Future One touch Cappuccino
Contents
1. ADVANCED SETTINGS FOR BREWING Speciality Coffees The Main Menu Coffee Recipes THE SETTINGS MENU Coffee Recipes using the Settings Menu Operating the Machine with or without the Water Filter Setting the Water Hardness Level Setting the Temperature Setting Time and Timer Functions Setting the Language Setting the Switch OFF Rinsing Function Setting the ECO Mode Reading Statistics MANUAL ADJUSTMENTS Setting the Grinder Preparing Pre Ground Coffee CARE CLEANING AND MAINTENANCE Rinsing the Cappuccinotori Milk Frother Cleaning the Cappuccinotori Milk Frother Rinsing the Spout Cleaning the System Descaling the System Regular Manual Cleaning of the Machine Cleaning the Brewing Unit Changing the Water Filter SYSTEM MESSAGES TROUBLESHOOTING ACCESSORIES FURTHER INSTRUCTIONS GUARANTEE Contents _ _ OO WANA AA HY AUAA HW WW W O M M M MA NIN OOUBR AND co C NNNNNNN DN N UUAN OOO NNNN N io O CON OV 1 Safety Instructions 1 Safety Instructions The SPRADA Future One Touch Cappuccino OTC is a domestic machine and not guaranteed for commercial use see guarantee conditions Operating voltage is 220 240 V Do not operate the machine if the Power Cord or machine case is damaged If damaged it should be replaced by a qualified technician Do not pull or let the Power Cord come into contact with hot parts2. and Fill up water 21 7 Care Raise the Height Adjustable Spout to its top position gt Remove the Drip Tray and the Coffee Grounds Container and empty them both gt If necessary fill the Water Reservoir with fresh water and put the Water Reservoir Drip Tray and Coffee Grounds Container back in the machine The machine will now start rinsing twice The display will now show the message Cleaning Tablet in powder shaft gt Open the cover on top of the machine gt Open the lid of the pre ground coffee chamber gt Place one Cleaning Tablet available separately see Section 9 in the pre ground coffee chamber and close the lid and cover gt Place a receptacle with at least 0 52 capacity under the Height Adjustable Spout The Display Screen will now show the message Start Cleaning gt Press the Rotary Control Knob The machine will now start the cleaning process and the Display Screen will show the message System Cleans The cleaning cycle will start automatically and last approximately ten minutes As soon as the cleaning cycle has finished the Display Screen will show the message Empty Tray gt Remove empty and clean the Drip Tray and the Coffee Grounds Container and put them back in the machine gt If necessary refill the Water Reservoir with fresh water The machine will now heat up and be ready for use again 7 5 Descaling the system 22 A A When the m
3. Sprada THE FUTURE FUTURE One Touch Cappuccino Fully Automatic Coffee Centre COFFEE YOUR ETE ES iT yk Familiarising yourself with your Future OTC D OW GD es 7 e Display Rotary Control Knob Button gt Button Exit Height Adjustable Spout Nameplate with Specifications inside Coffee Grounds Container inside Mains Switch on side panel Cover Panel Drip Tray T rOA MONWDS YDPVOZSETA Removable Water Reservoir Bean Container inside Pre Ground Coffee Chamber inside Cup Holding Plate Cup Warming On Off Button On Off Switch Service Door side panel Rear Rollers underneath at the back Milk Cooler Thermos Important areas on your Future OTC Water Reservoir K Water Filter Bean Container L Milk Cooler Thermos S Cappuccinotori access Grinder Setting Control Brewing Unit Release 2 1 2 2 2 3 2 4 2 5 3 1 3 2 3 3 3 4 35 3 6 4 1 4 2 5 1 5 2 5 3 5 4 5 5 5 6 5 7 5 8 5 9 6 1 6 2 7 1 7 2 7 3 7 4 7 5 7 6 7 7 7 8 10 11 12 SAFETY INSTRUCTIONS SETUP Preparing the Machine The most important Controls Adding Water and Beans The Cappuccinotori Milk Frother Pre Warming your Cups SWITCHING ON AND GETTING STARTED Mains Switch On Off Switch Brewing with Factory Settings Brewing two Cups of Coffee Emptying the Drip Tray and the Coffee Grounds Container Hints for First Time Users
4. Centres Guarantee and customer service conditions Please consult the detailed guarantee and customer service conditions in the appropriate information booklet Please visit our website www sprada ch for additional information on this product 12 Guarantee Your SPRADA Future OTC is a precision device manufactured to the highest European standards and is guaranteed against manufacturing defect for a period of one year from the date of purchase or until it has made 7500 cups whichever comes first The machine is not guaranteed against damage caused by normal wear and tear neglect or misuse arising from operation not in accordance with that described in the manual or lack of routine cleaning as specified and furthermore it is not guaranteed against damage caused by power fluctuations or surges or lightning strikes To ensure that your guarantee is valid please retain your proof of purchase In addition you can submit your details via the easy to use Electronic Guarantee Option on the website www sprada ch with the date of purchase and attach a copy of the original invoice from your retailer Should you wish to claim under this guarantee please return the SPRADA Future OTC in its original packaging together with a detailed description of the fault to one of our service centres that can be found on www sprada ch A downloadable repair form is available from the website to facilitate this process Upon receipt our technicians will i
5. Do not pull on the Power Cord to disconnect the machine e Observe the cleaning amp descaling instructions provided Otherwise claims under the guarantee may not be accepted Make sure to switch off and unplug the machine before maintenance or cleaning e The SPRADA Future OTC is for indoor use only and should be located on a firm and level surface Do not place the machine on a hot surface or near an open flame e Keep out of reach of children and ensure that they do not play with the appliance Unplug the machine during extended periods of absence Do not leave the machine switched on unnecessarily e Never allow the machine to become submerged in water Do not use a dishwasher to clean the machine or individual parts Unplug immediately if there is a defect Liability for damage cannot be accepted if the machine is incorrectly operated or serviced by non accredited service agents Make sure there is nothing but roasted coffee beans in the beans container e This machine is not suitable for individuals including children with physical sensory or mental impairments including individuals who do not have sufficient experience or knowledge unless they are shown how to operate the machine or initially supervised by someone responsible for their safety e Please contact the retailer from whom you purchased the machine for repair or send the machine to a SPRADA national customer service centre 1 Safety Instr
6. Screen will show the message Connect hose pipe with Spout and put in Drip Plate gt Connect one end of the hose to the Height Adjustable Spout Place the other end of the hose in the Drip Tray at the rear on the right The Display Screen will now show the message Cleaning Frother do not remove h p As soon as the cleaning cycle has finished the machine will heat up and be ready for use 7 3 Rinsing the Spout You should rinse the Spout from time to time Rinse the Spout as follows gt Turn the Rotary Control Knob to the maintenance symbol Press the Rotary Control Knob gt Turn the Rotary Control Knob to Rinse Spout Press the Rotary Control Knob The Display Screen will now show the message Rinsing As soon as the rinsing cycle has finished the machine will heat up and be ready for use again 7 4 Cleaning the system The machine detects when it should be cleaned Please Clean will appear on the Display Screen You can still brew coffee or prepare hot water and steam but we would advise you to run the cleaning program as soon as possible The cleaning process takes about 10 minutes Caution You must not interrupt the cleaning program whilst it is running Only add Cleaning Tablets when indicated by the machine gt Turn the Rotary Control Knob to Clean system Press the Rotary Control Knob The Display Screen will now alternately show the messages Empty trays
7. taste For easy use the most important controls are common to the various Speciality Coffees and machine setup functions The Main Power Switch is on the lower left hand front side of the machine The On Off Switch is on the top of the machine The multi function turn and press control knob Rotary Control Knob for short is the most important control Rotating it selects options and menu items while pressing it confirms the selection or initiates the machine cycles The gt Button Press the gt Button to move to the next menu or item The Exit Button Press the Exit Button to move one menu level back or abort a process in progress The Height Adjustable Spout moves up and down to accommodate different sizes of cups or glasses 2 Set up 2 3 Adding water and beans A Water e Open the cover on the left side of the machine and remove the Water Reservoir e Rinse and fill the Water Reservoir with cold water up to the maximum mark and click into place on the machine Caution only fill the Water Reservoir with cold clear water Never use carbonated water or other liquids Note The machine will not function if the water level is too low The display will indicate Fill up water Beans e Open the cover on the right hand side of the machine Remove the Bean Container lid and fill with untreated roasted coffee beans Close the lid and the cover Caution Do not use beans tre
8. than a few minutes a message Please rinse will appear on the Display Screen accompanied by a flashing semi circular icon in the bottom centre of the display to indicate that the Rotary Control Knob should be pressed gt Press the Rotary Control Knob The system rinses and the Main Menu is displayed 3 3 Brewing with Factory Settings The Main Menu on the Display Screen is a visual representation of the different Speciality Coffees that your SPRADA One Touch can make You can start making coffee immediately as each icon represents a coffee brewed according to Factory Settings e Espresso the world s best e Caf Cr me black with superior creme and aroma e Caffe Lungo for the BIG coffee lover e Cappuccino delicious frothy coffee e Latte Macchiato layered milk and coffee as you like it e Warm Milk for hot chocolate e Hot Water for tea ee all at the touch of one button Place the cup under the Height Adjustable Spout Turn the Rotary Control Knob to highlight an icon gt Press the Rotary Control Knob to start the brewing process The brewing light will illuminate and a delicious cup of coffee will be dispensed 3 Switching on and getting started While the brewing cycle is in process the icons below the bar on the display will flash Turning the Rotary Control Knob will change the setting of the flashing icon At any stage the process can be aborted by pressing the Exit Button next to the
9. will not see a message on the Display Screen in this case Using the dial at the head of the Filter the month display you can set the Filter change date 25 8 System messages 8 System Messages Message FILL UP PIPE SYSTEM Meaning Fill or rinse out water hoses inside Fresh water Filter in use may be faulty What to do Press the Rotary Control Knob Remove or change the Filter cartridge FILL UP WATER FILL UP BEANS Water Reservoir is empty Water Reservoir is absent or incor rectly positioned Not enough coffee beans Coffee beans do not fall into Grinder stuck Add fresh water Correctly position Water Reservoir see point 2 3 Add beans to the container see point 2 3 Stir beans e g with a spoon to loosen Note The message FILL UP BEANS only disappears when coffee has been brewed after refilling EMPTY TRAYS Drip Tray and or used coffee tray are full Contacts on back of Drip Tray are not clean and or dry Empty Drip and or used Coffee Tray Clean dry contacts TRAYS MISSING PLEASE CLEAN Drip Tray and Coffee Grounds Container used are absent or not correctly positioned Contacts on back of Drip Tray are not clean and or dry Cleaning programme is needed Position drip and coffee trays correctly Clean dry contacts Clean machine see point 7 4 PLEASE DESCALE Descaling programme is needed Descale the machine see poi
10. Cooler Thermos with warm soapy water to keep it in perfect condition 2 5 Pre Warming your cups Your machine is equipped with a high quality active Cup Warming Function that can be switched on and off while power is applied gt Press the button to turn on the Cup Warming Function The Mains Switch must also be on The Display Screen will show the message Cup Heater On gt By pressing the button again you can turn the Cup Warming Function off The Display Screen will show the message Cup Heater Off E Tip Use the warming function to optimise the temperature and aroma of your coffee to enhance your coffee experience 3 Switching on and getting started 3 Switching on and getting started 3 1 Mains Switch Switch on the Mains Switch located at the lower left hand front side of the machine to put the machine in Standby Mode An on off symbol will move across the display if the Clock Function has not been setup If the Clock Function has been initialised the time will be displayed Note If you are switching on a brand new machine first skip forward to Section 5 to set up the basic functions 3 2 On Off Switch gt Press the On Off Switch on top of the machine to bring the machine out of Standby A The message Heating will appear on the Display Screen accompanied by a rotating hourglass icon to indicate that an action is happening inside the machine If the machine has been off for more
11. Rotary Control Knob For instance if the cup size does not correspond to the capacity of the cup under the Spout press Exit to stop it overflowing 40m ix cE Hint You may notice a delay between the grinding and dispensing of coffee when making milky drinks This extra time is for the Cappuccinotori Milk Frother to heat up in order to prepare warm rich and creamy milk After a set amount of time the machine reverts to energy saving mode Save Energy is displayed on the display panel Touching any control will immediately bring up the Main Menu again 3 4 Instructions for brewing two cups of coffee To brew two cups of coffee one after the other press the Rotary Control Knob twice in quick succession when starting the brewing process Another method is to press the gt Button until the 1x 2x icon below the display bar is highlighted and then use the Rotary Control Knob to select 2x Press the Exit Button to save the setting Two consecutive grinding processes will automatically occur If the water or bean supply runs out or the trays have to be emptied after the first grinding process you will be notified on the Display Screen and the second cup of coffee will not be brewed gt Follow the message on the Display Screen and then press the Rotary Control Knob once to brew the second cup of coffee 3 Switching on and getting started 3 5 Emptying the Drip Tray and Coffee Grounds Container T
12. achine needs to be descaled the following message will appear on the Display Screen Please Descale You can also start the descaling program manually at any time Caution Please follow the instructions below exactly as given You can continue to prepare drinks but we would advise you to carry out the descaling program as soon as possible Caution You must not interrupt the descaling program whilst it is running Never use vinegar or vinegar based products for descaling Always use the liquid products normally recommended for fully automatic coffee centres Clean frother Clean EN 7 Care Caution You must remove the Filter from the Water Reservoir before starting the descaling program gt Turn the Rotary Control Knob to the maintenance symbol Press the Rotary Control Knob gt Turn the Rotary Control Knob to Descale system Press the Rotary Control Knob The Display Screen will now show the message Empty Tray gt Remove the Drip Tray and the Coffee Grounds Container and empty gt Put the Drip Tray and the Coffee Grounds Container back in the machine The Display Screen will now show the message Remove Tank gt Fill the Water Reservoir up to the 0 52 mark with fresh water and add the Descaling Agent available separately see Section 9 Put it back in the machine Caution Always first add water up to the 0 52 mark and then add the Descaling Agent never the other way round Follo
13. ated with supplements such as sugar either during or after roasting Supplements can damage the grinding mechanism Note The machine automatically detects when the bean level is low and will not function The display will indicate Fill up beans 2 4 The Cappuccinotori Milk Frother The SPRADA One Touch is supplied with an insulated Milk Cooler Thermos which attaches directly to the machine to make delicious milky coffee and hot milk drinks Connect one end of the pipe to the top of the Milk Cooler Thermos Make sure it is pushed down firmly into the grommet on the removable lid of the container Connect the other end of the pipe to the grommet on the right hand side of the Height Adjustable Spout Unscrew the top of the Milk Cooler Thermos and make sure that the steel pipe is firmly inserted in the grommet from the inside This ensures that milk is sucked up right to the bottom of the container Fill the Thermos with cold milk Screw the lid back on the Milk Cooler Thermos and make sure the pipe is not stretched tight as this might impede the flow of milk The milk in the container should remain cold for some hours because of the high quality insulation 2 Set up Always empty and clean the Milk Cooler Thermos a minimum of once a day Rancid milk can cause blockages that will cause malfunction of the machine Caution Do not wash the Milk Cooler Thermos in a Dishwasher as this will damage it Hand wash the Milk
14. coffee is being brewed gt Ifyou wish to abort a brewing process press the Exit button Please note if you inadvertently open the pre ground coffee chamber or did not press the Rotary Control Knob after adding pre ground coffee the machine will automatically be rinsed approximately one minute after the lid is closed and it will then be ready for use again Caution The pre ground coffee chamber is not a storage unit so please only add one portion at time and only use fresh or vacuum packed pre ground coffee produced from coffee beans Do not use water soluble instant coffee 19 7 Care 7 Care Cleaning and Maintenance 7 1 Rinsing the Cappuccinotori Milk Frother A N Caution Do not interrupt the rinsing program whilst it is running Rinse the Cappuccinotori Milk Frother after every milky drink or when a message appears on the display alternating with the selected drink message gt Turn the Rotary Control Knob to select the Care icon Press the Rotary Control Knob gt Turn the Rotary Control Knob to Rinse Frother Press the Rotary Control Knob The Display Screen will now show the message Connect hose pipe with Spout and put in Drip Plate gt Remove the hose end connecting the Milk Cooler Thermos with the Height Adjustable Spout and connect to the Drip Tray grommet at the right rear of the Drip Tray Image gt Place a receptacle with at least 0 52 capacity under the Height Adjus
15. elected will apply to all drinks and only if you select Individually will you be able to set different temperatures for different drinks gt Turn the Rotary Control Knob to select your desired Temperature gt Press the Rotary Control Knob to confirm your selection Note If the Temperature is not set to Individually in this menu the Temperature option will be removed on the Coffee Recipes menu 14 5 The Settings Menu 5 5 Setting Time and Timer Functions Tines Unit suto OW at Unit auto OFF after Cup heater auto ON Time format 2 12pm Set clock Hours Unit auto OH at Set au Exit Unit auto OFF after Time is a versatile method of controlling the The SPRADA One Touch There are a number of options in this menu which must be set in sequence Clock Options are Disabled or Set Clock Disabled disables all Clock Functions and a small on off icon will appear on the Display Screen when the SPRADA Future OTC is in Standby mode To disable scroll down to the option with the Rotary Control Knob and press to select Select Exit to return to Times menu Set Clock When this is set the time will be displayed when the SPRADA One Touch is in Standby mode Select by pressing the Rotary Control Knob The hours display flashes Set to current hours with Rotary Control Knob Press to select The minutes display flashes Set the curr
16. ent minutes and press to select The display returns to the Times menu to confirm that the clock has been successfully set Note Once the clock time has been set it will appear on the display screen when the machine is in standby mode If the clock time has not been set the on off symbol will appear on the display screen in standby mode Unit Auto ON at The SPRADA One Touch can be programmed to switch itself on every day at a set time Select either Disabled or set the time at which you wish the machine to come on automatically using the same method as detailed above Press Rotary Control Knob to confirm selection The display will return to the Times menu automatically when the Auto ON has been successfully set Note If you Select Disabled you must Exit to return to the Times menu Unit Auto OFF after Select with the Rotary Control Knob from 0 5 hours to 12 hours Press Rotary Control Knob to confirm selection Display will return to Times menu when the Auto OFF has been successfully set 15 5 The Settings Menu Cup heater suto OH Exit Time format Cup Heater Auto ON Select Disabled Enabled with the Rotary Control Knob Press the Rotary Control Knob to confirm selection Time format Select either 24 hours or am pm with the Rotary Control Knob Press the Rotary Control Knob to confirm selection Select Exit or press Exit Butt
17. f water The Display Screen will then show the message Replace Filter You can continue to prepare drinks but it is advisable to change the Filter immediately gt Select Settings with the Rotary Control Knob and press to confirm gt Select Filter with the Rotary Control Knob and press to confirm gt Select Insert Filter Yes so that the machine knows that the Filter is being inserted gt Empty the Water Reservoir and unscrew the old Filter using the Assembly Tool at the end of the Measuring Spoon Remove it from the holder provided in the Water Reservoir gt Press the Rotary Control Knob The message Insert Filter or Filter Inserted will now appear on the Display Screen gt Carefully screw the new Filter available separately into the holder provided in the Water Reservoir using the Assembly Tool at the end of the Measuring Spoon Caution Be careful not to turn too far or to cause it to snap off gt Fill the tank with fresh water and put it back into the machine gt Place a receptacle with at least 0 52 capacity under the Spout and press the Rotary Control Knob The message Rinsing Filter will appear on the Display Screen and the machine will rinse Thereafter the message Heating will appear on the Display Screen and the machine will then be ready for use Caution Even if you use only a small amount of water you must change the Filter at least every two months You
18. for sophisticated control of your personal tastes refer to Section 5 1 1 Using the Display Bar Icons All Speciality Coffees Warm Milk Hot Water and My Coffee can be adjusted by pressing the gt key next to the Rotary Control Knob The icons below the bar on the display represent the current settings and can be adjusted to suit individual taste and cup sizes The icon below the Display Bar will flash when selected to indicate that modifications of the settings are in progress The Rotary Control Knob is then used to modify the setting and the Exit button pressed to store the modifications Pressing the gt Button first selects the coffee strength and is adjustable from one bean to five beans 6686G40om 1x Gf 4 Adjusting the Basic Settings 10 Pressing the gt Button again allows setting of the cup volume from 20ml to 240ml according to the cup size Pressing the gt Button again highlights 1x 2x and either one cup or two cups can be made automatically If a milky coffee setting is being modified Pressing the gt Button will allow the ratio of milk to coffee to be changed A higher percentage equals more coffee and less milk and a lower percentage equals more milk and less coffee The taste is preserved by automatically changing this ratio if the cup size is changed Press the Exit key and the icon on the Main Menu flashes to indicate that the new settings are bei
19. g the Test Strip A Water Hardness Detection Strip is supplied with the machine as an accessory It is used to determine Water Hardness Water hardness ei gt Dip the Test Strip in the water and shake off excess water gt After about a minute count the number of Red Dots on the Test Strip gt The number of dots correspond to the hardness level Test Strip Degree of hardness display 1 Red Dot HARDNESS LEVEL 1 2 Red Dots HARDNESS LEVEL 2 3 Red Dots HARDNESS LEVEL 3 4 Red Dots HARDNESS LEVEL 4 Gi Note If no Red Dot appears set Water Hardness to Level 1 Setting the Water Hardness Level The basic factory setting for Water Hardness is LEVEL 3 but this depends on Water Hardness in your area The machine detects when descaling is necessary but the correct Water Hardness level must be set before using the machine Setting the Water Hardness Level gt Turn the Rotary Control Knob to select Water Hardness gt Press the Rotary Control Knob to confirm your selection gt Match the flashing Level to that measured with the Water Hardness Testing Strip with the Rotary Control Knob gt Press Rotary Control Knob to confirm selection 5 4 Temperature The Temperature can be set with the Rotary Control Knob to Normal High Maximum or Individually Temperature ign Maasi mum Individually Exit The factory setting is High for all Speciality Coffees The setting s
20. he Drip Tray and Coffee Grounds Container are integral to the machine and require emptying on a regular basis or when the display indicates that this should be done with the message Empty Drip Tray Move the Height Adjustable Spout to its uppermost position Grasp the Drip Tray assembly in the middle and carefully pull outwards The message Insert Tray will be displayed and the machine will not operate Remove the Coffee Grounds Container empty and rinse with clean water Empty the Drip Tray and rinse with clean water Remove the stainless steel Drip Cover and wash with clean water Re assemble the components of the Drip Tray assembly Gently push the Drip Tray all the way in and seat The display will return to the Main Menu and the machine can be used 3 6 Hints for First Time Users If the message Fill Up Pipe System appears on the display when the SPRADA Future OTC is used for the very first time Refer to section 2 3 gt Place a receptacle or large cup with its centre under the Spout gt Press the Rotary Control Knob The system will now be filled Water may come out of the Spout After the system has heated up the message Please Rinse will appear on the Display Screen gt Press the Rotary Control Knob again The system is now filled with water If the message Fill up beans appears on the display gt Fill the bean hopper gt Select any coffee gt Press the Rotary Control K
21. he Height Adjustable Spout gt In the Main Menu turn the Rotary Control Knob to Espresso the Espresso symbol gt Press the Rotary Control Knob gt While the Grinder is grinding change the Grinder setting by moving the Grinder Setting Control The smaller the dot the finer the ground coffee e alight roast requires a finer setting control further to the left e a dark roast requires a coarser setting control further to the right You can try different settings to find the one which best suits your taste gt Close the service door guiding the projections at the rear of the door into the corresponding recesses and pressing the door to click it shut 6 2 Preparing Pre Ground Coffee 18 gt Open the cover on top of the machine gt Open the lid of the Pre Ground Coffee Chamber After a moment the Display Screen will show the message Fill in Coffee Powder alternating with the message Close Powder Shaft gt Add one level Measuring Spoon of pre ground coffee Close the lid and the cover The display will now show the message Powder is ready gt Place a cup under the Height Adjustable Spout gt Inthe Main Menu turn the Rotary Control Knob to the drink of your choice gt Press the Rotary Control Knob to start brewing your coffee 6 Manual Adjustments Please note If you start preparing your coffee inadvertently or too early you can actually change the amount while the
22. here the machine uses minimal power but is ready for use at the touch of a button This can either be Disabled or the delay set from 3 minutes to 15 minutes before going into ECO Mode Touching any control on the machine brings the machine out of ECO mode but will take a few seconds longer to heat up Select the function using the Rotary Control Knob Press to confirm selection Statistics shows an interesting breakdown of the drinks that the machine has brewed since it was set up Select using Rotary Control Knob Press to confirm selection Scroll down list using Rotary Control Knob for information on ny M n M n M Espresso Caf Cr me Caff Lungo Cappuccino Latte Macchiato My coffee Powder Coffee 1 cup 2 cups Total sum of all coffees Hot water Milk Cleaning Descaling Filter replace Press Exit to return to the Setup menu 17 6 Manual Adjustments 6 Manual Adjustments 6 1 Setting the Grinder Caution The Grinder setting can only be changed while the Grinder is operating The Grinder can be adjusted to suit the roast of your coffee beans It is advised that you always keep the Grinder on a medium setting To change the grinding level gt Open the service door on the right side of the machine The Grinder Setting Control is on the top right Image gt Place a cup under t
23. k Cooler Thermos and rinse Remove the Cappuccinotori by pulling it downwards and dismantle it Clean the components thoroughly and reassemble Push the Cappuccinotori back up into the Height Adjustable Dispenser and carefully seat Attach the cover panel Reconnect the pipe to the Milk Cooler Thermos VV Vvvv vv The machine is ready for use and the Main Menu will be displayed Please note Your machine is equipped with moving rear rollers and can be moved on a level work surface So you can also clean underneath the machine 7 Care 7 7 Cleaning the Brewing Unit Caution Only remove the Brewing Unit when the machine is in Standby mode Open and remove the service door on the right of the machine To unlock the Brewing Unit press the red button and turn the handle all the way to the left until it unlocks Remove the Brewing Unit carefully using the handle Clean the Brewing Unit under clean running water and leave it to dry Do not use detergents to clean and never put it in the dishwasher Carefully put the Brewing Unit back in the machine and lock it in by pressing the red button and turning the handle all the way to the right until the unit clicks into place Close the service door by first guiding the projections at the rear of the door into the corresponding recesses and then pressing the door to click it shut VVVVU vv Vv 7 8 Changing the Filter Filters lose their efficiency after processing about 502 o
24. ll not have to descale your machine as often However using the Filter is only an option and will depend on the water quality in the your area Filter inserted No is the default setting You must set the filter setting to Filter inserted Yes Highlight and select Filter with the Rotary Control Knob gt Turn the Rotary Control Knob to select Insert Filter Yes so that the machine knows that the Filter is being inserted gt Press the Rotary Control Knob The message Insert Filter appears on the Display Screen gt Empty the Water Reservoir and carefully screw the Filter into the holder provided in the Water Reservoir using the Assembly Tool on the end of the Measuring Spoon N Caution Do not overtighten as it could snap off gt Fill the Water Reservoir with fresh water and put it back into the machine gt Place a receptacle with at least 0 52 capacity under the spout and slightly to the left and press the Rotary Control Knob The message Rinsing Filter appears on the display screen 12 O 5 The Settings Menu gt Wait until water stops coming out of the spout The message Please Rinse appears on the Display Screen gt Press the Rotary Control Knob The machine rinses and is ready for use Note ALWAYS TAKE THE FILTER OUT before descaling The Filter loses its efficiency after precossing about 50 litres of water Note Even if the Display Screen does not
25. ng stored and all subsequent drinks will be made using this setting Please note If you start brewing your coffee inadvertently or too early you can actually change some parameters while the coffee is being brewed The parameter that you can change with the Rotary Control Knob will flash in the bottom line of the Display Screen 5 The Settings Menu 5 The Settings Menu OC OLE The Settings menu allows access to many other functions that are integral to the operation of the SPRADA One Touch Scroll through the options using the Rotary Control Knob and select by pressing e Coffee recipes e Filter e Water Hardness e Temperature e Times e Language e Off rinse e ECO mode e Statistics e Exit 5 1 Coffee Recipes Using the Settings menu recipes il ter Water hardress Teapera ture imes OCE You can do everything you have learnt so far and more by accessing the recipes under the Settings icon Scroll through the list of options with the Rotary Control Knob and press to select Highlight Coffee Recipes and confirm selection by pressing the Rotary Control Knob Classic coffees Espresso Caf Cr me and Caffe Lungo have three items in the recipe that can be selected using the Rotary Control Knob e Flavour Very Mild Mild Normal Strong Very strong e Amount Total Dependant on cup size and can be set from 20ml to 240ml e Temperature Normal High Maximum The display item fla
26. nob gt Ifthe Grinder does not grind it is because it is still empty gt Press the Rotary Control Knob again The Grinder is now full and grinding will take place 4 Adjusting the Basic Settings 4 Adjusting the Basic Settings For the more advanced coffee lover Once you have mastered the basic settings and to get the most out of your machine you can change the basic settings to match your own preferences 4 1 The Main Menu The Main Menu is the key to making the SPRADA One Touch your own Each speciality coffee is represented by an icon Espresso Caf Creme Caffe Lungo Cappuccino Latte Macchiato In addition there are icons for Warm milk and Hot water For ultimate ease the My Coffee icon can be assigned to any coffee recipe from the list above The Settings icon explained in Section 5 and the Care icon explained in Section 6 allow even greater control of the internal functions of the machine Highlighting the icon with the Rotary Control Knob and then pressing the Rotary Control Knob initiates the brewing process While highlighted the recipes and functions can be personalised as explained below 4 2 Coffee Recipes Your SPRADA machine enables you to brew a range of speciality coffees just how you like them There are two methods of changing the Factory Settings to suit your preference 1 Using the icons under the Display Bar on the display 2 Using the Settings icon
27. nspect the machine and deliver a full report on the probable cause of the defect Should this be attributed to amanufacturing fault the machine will be repaired at no charge Should the fault have been caused by one of the above circumstances not covered by the guarantee a quotation will be submitted for the repair Courier fees will be for the account of the purchaser 29
28. nt 7 5 REPLACE FILTER BREWING UNIT REMOVED Filter is no longer efficient Brewing Unit is incorrectly positioned inserted Replace Filter see point 7 8 Check and insert lock Brewing Unit correctly see point 7 7 26 9 Troubleshooting Fault Meaning No hot water steam comes Milk Frother is blocked out of jet 9 Troubleshooting What to do Disassemble and clean Milk Frother thoroughly Too little milk foam or foam The system may have a build up of too liquid lime scale Unsuitable milk Milk Frother is blocked Please use a large dose of descaler see point 7 5 Use cold milk Disassemble and clean Milk Frother thoroughly Coffee only comes out in drips The system may have a build up of lime scale Grinder setting is too fine Pre ground coffee is too fine Please use a large dose of descaler see point 7 5 Select coarser Grinder setting Use coarser pre ground coffee Coffee without crema The system may have a build up of lime scale Unsuitable coffee type Please use a large dose of descaler see point 7 5 Change coffee type Grinder makes loud noise Beans no longer fresh Grinder settings not adjusted to coffee beans Other substances in Grinder e g little stones Use fresh beans Optimise Grinder settings Contact Customer Service meanwhile pre ground coffee can be used If you are unable to correct a fault system me
29. on to return to Settings Menu Note If the machine has been switched off at the mains or if there has been a power failure the clock and the Auto ON functions must be set again 5 6 Setting the Language Sprache Deuts Langue fF rare amp Linguas Italiano Idioma Espa ol 5 7 OFF Rinse OFF Finzse Disabled Exit 16 The language used on the display can be changed with the Rotary Control Knob Select and highlight language of preference with the Rotary Control Knob Press to confirm selection The Switch On Rinsing Function is pre programmed by the manufacturer Each time it is switched on when cold the machine will first rinse to ensure that the machine always dispenses fresh water The Display Screen indicates when rinsing is required and the rinsing function must be started manually by pressing the Rotary Control Knob The option can be set to also rinse the machine on switching off Select Enabled Disabled using the Rotary Control Knob Press to confirm selection Note If the OFF Rinse Function is enabled the machine will only be rinsed if it has brewed at least one drink before being switched off 5 8 ECO Mode ECO Mocde lisablec Disabled After 3 Ainutes After 3 Ainutes After 15 Minutes Exit 5 9 Statistics Statistics Espresso Caf Crime Caffe Lungo re Latte Hscohiato 5 The Settings Menu A unique feature of the SPRADA Future OTC is the power saving ECO Mode w
30. process The Display Screen will now show the message Rinsing The rinsing cycle will start and run automatically for approximately two minutes As soon as the rinsing cycle has finished the Display Screen will show the message Empty Tays gt Empty and clean the Drip Tray and the Coffee Grounds Container and put them back in the machine The machine is ready for use Caution Please always remove all descaling residue left on the machine with a damp cloth machine regularly by hand Caution Never submerge the machine in water and do not use scouring agents gt Clean the machine inside and out using only a soft damp cloth gt Move the Height Adjustable Spout to the uppermost position and empty the Drip Tray and the Coffee Grounds Container regularly or when indicated to do so on the Display Screen This will only be indicated when the machine is on Ensure that both metal contacts and the areas between them at the rear of the tray are always clean and dry gt The Water Reservoir should be rinsed with clear water and refilled with fresh cold water every day gt Clean the Cappuccinotori Milk Frother Hose and Spout regularly If the machine is to be left unused for a period of time the Cappuccinotori Milk Frother must be dismantled and rinsed under clear running water Remove the Cover Panel of the Height Adjustable Spout The display will indicate Attach Frother Remove the pipe to the Mil
31. shes when it can be set with the Rotary Control Knob Press the Rotary Control Knob when you have set your preference Milky drinks Cappuccino and Latte Macchiato have five parameters that can be selected and customized using the Rotary Control Knob e Flavour Very Mild Mild Normal Strong Very strong e Amount Total Dependant on cup size and can be set from 20ml to 240ml Changing this will affect the Prop coffee and the Amount Frothy milk e Prop coffee The amount of coffee in the drink expressed as a percentage Changing this will not affect the Amount Total but will change the Amount Frothy milk 11 5 The Settings Menu e Amount Frothy milk The amount of milk in millilitres Changing this will not affect the Amount Total but will change the Prop coffee Temperature Normal High Maximum Hot Water Used for making tea for instance Has no settable items oR O Warm Milk Two items can be changed e Amount total The amount of hot water and milk together e Prop Frothy milk The amount of milk in the mixture expressed as a percentage from 0 to 87 ITY My coffee Can be set to brew any of the classic coffees or milky coffees To return to the Main Menu select Exit or press the Exit Button 5 2 Operating the machine with or without the Filter Operating the machine with a Filter A Claris Filter and an Assembly Tool are supplied with the machine as accessories If you use this Filter you wi
32. show the message Replace Filter and even if the machine is only used occasionally the filter must be changed every two months Operating the machine without a Filter If you wish to operate the machine without the filter you must set the filter setting to Filter inserted No This is important because the machine needs to be descaled more often if operated without a filter depending on water hardness The machine s default factory setting is Filter inserted No Press to confirm No and the machine reverts to the Settings menu gt Turn the Rotary Control Knob to select Insert Filter No gt Press the Rotary Control Knob to confirm your selection The water hardness setting will now appear on the Display Screen Please note once again It is possible that the machine s pipe system will still be empty when it is set up This will be indicated when the machine is turned on using the On Off Button as the message Fill up pipe system will appear on the display screen gt Place a receptacle with at least 0 51 capacity with its centre under the spout gt Press the Rotary Control Knob The system will now be filled Water may come out of the spout After the system has heated up the message Please rinse will appear on the display screen gt Press the Rotary Control Knob The system will now be filled with water 13 5 The Settings Menu 5 3 Water Hardness Usin
33. ssage yourself calla SPRADA Service Centre and please consult the Guaratee details in Section 13 Caution If the display reads Error Service Tel note the code Switch off and unplug the machine and call a SPRADA Service Centre and with the helpof the code they will be able to suggest the best course of action 27 10 Accessories 10 Accessories 28 You can purchase new accessories from any well stocked specialist retailer or contact SPRADA directly CLARIS Filter Cartridge The CLARIS Filter Cartridge is filled with purely organic material without chemical additives and if changed regularly it ensures that you will have to descale your SPRADA machine less often SPRADA Cleaning Tablets Your fully automatic coffee centre provides an integrated cleaning programme Cleaning Tablets are specifically designed for this purpose and completely remove stains from coffee residues SPRADA Descaling Tablets Your fully automatic coffee centre provides an integrated descaling programme The descaler will reliably remove lime scale without damaging the machine SPRADA Milk Cleaning Powder SPRADA Milk Cleaning Powder easily cleans all Milk Frothers of milk residues 11 Further instructions 11 Further instructions Customer service SPRADA products are designed to meet the highest quality standards If you have questions as to the operation of your machine please consult your dealer or contact the SPRADA Service
34. table Spout as this cleaning takes place under high pressure and can cause splashing gt Press the Rotary Control Knob The following message will appear on the Display Screen Rinsing Frother do not remove h p hosepipe The rinsing cycle will start automatically and last approximately twenty seconds As soon as the rinsing cycle has finished the machine will heat up and be ready for use again 7 2 Cleaning the Cappuccinotori Milk Frother N Caution Do not interrupt the cleaning program whilst it is running Clean the Cappuccinotori Milk Frother from time to time or as indicated automatically on the display gt Select Clean Frother with the Rotary Control Knob and press to select The Display Screen will show the message Connect hose pipe with Spout and put in cleaner gt Put some water and cleaning agent available separately with a total volume of at least 0 32 in a container Follow the cleaning agent manufacturer s instructions to obtain the correct mixing ratio 7 Care gt Connect one end of the hose to the Height Adjustable Spout and submerge the other end of the hose in the cleaning solution gt Place a receptacle with at least 0 52 capacity under the Height Adjustable Spout gt Press the Rotary Control Knob The machine will now start the cleaning process and the Display Screen will show the message Cleaning Frother do not remove h p After a short time the Display
35. uctions gt gt Caution Electrical appliances should be repaired only by qualified personnel as non professional repairs can expose the user to significant risk Liability for damages cannot be accepted if the machine is used for anything other than the intended purpose or is incorrectly maintained or serviced Caution Using the On Off Switch or Mains Switch during brewing can damage the machine Only switch off the appliance when in Standby mode Caution Splashes from the Spout can cause scalding when drawing steam or hot water Leave to cool for a few minutes before touching Specifications Mains voltage 220 240 V Power requirement 1465 W 2 Set up 2 Set up 2 1 Preparing the machine The following items are packaged with the machine User Manual Milk Cooler Thermos with separate Connecting Pipe Measuring Spoon with Assembly Tool for Filter 2 Cleaning Tablets 1 Claris Water Filter 1 Water Hardness Test Strip Unpacking Carefully remove the machine and all parts from the packaging Please keep all packaging including the styrofoam inserts in case you need to return the machine for service Place the machine on a level dry and stable work surface Connect the machine to a properly installed mains socket Place the Milk Cooler Thermos upright next to the machine and connect pipe 2 2 The most important controls Your SPRADA One Touch brews a range of Speciality Coffees according to your own personal
36. w the Descaling Agent manufacturer s instructions gt Connect one end of the hose to the Height Adjustable Spout gt Place the other end of the hose in the Drip Tray at the rear on the right The Display Screen will now show the message Start Descaling gt Place a receptacle with at least 0 52 capacity under the Spout and slightly to the left gt Press the Rotary Control Knob The machine will now start the descaling process and the Display Screen will show the message System Decalcifies The descaling process will start automatically and will last approximately twenty minutes The Descaling Solution will flow through the system at intervals Once all the Descaling Solution has flowed through the system the Display Screen will show the message Empty Trays Remove the Drip Tray and Coffee Grounds Container and empty them both Put the Drip Tray and the Coffee Grounds Container tray back in the machine Remove the Water Reservoir and rinse it out with clear water Replace the Filter in the Water Reservoir if used Fill the Water Reservoir with fresh water and put it back in the machine Connect one end of the hose to the Height Adjustable Spout Place the other end of the hose into the Drip Tray at the rear on the right VVVVV vv The Display Screen will now show the message Start Rinsing 23 7 Care A 7 6 Cleaning the 24 gt Press the Rotary Control Knob to start the rinsing
Download Pdf Manuals
Related Search