PLE430PX - Manual
Contents
1. SUB CHANNEL speakers SUB CHANNEL power amplifier mounting and installation Please take the time to install your ple430px 2 4 x 6 mm machine screw 4 New Pyle Signal Processor ss a ee Securely according to this _ dashboard oN P i SS l diagram using the hardware Pin I 3 Provided Ee eer 1 This Half DIN size unit can also de installed inthe dash th adjacent to thehead unit provided thatthere isa slot available T Mounting Bracket 4x12 mm self tapping screw 2 E 4 mm spring When making electrical washer 2 connections to your amplifier 4 mm plain please observe the following washers Connect 12V DCfrom aconstant battery source to a 12V slip on spadeterminal and install a one 1 ampfuse in line Connect the signal processors GROUND toa good chassis ground near where the unit is mounted or tothe case ofthe head unit Connect the signal processors REMOTE TURN ON lead to theremote turn on lead out ofthe head unit andinstall a 1 2 amp fuse inline A relay should beused if turningon more than one component suchas Eqs Crossover or amplifier Connect stereo RCA cables from the heads left andright from outputs to theleft and right inputs of the signal processor Connect stereo RCA cables from the leftand right outputs and low mid andhigh outputs if applicable ofthe signal processor to theleft and rightinputs of youramplifier s o2. PYLE precautions ple430px a Never drive with the volume raised so high you cannothear whatis occurring in traffic around you a Be awarethat repeated exposure to excessive volume levels can permanently damage your hearing a Keep allelectronics away from moisture dust extreme heator extreme vibrations a Pyle Audio products are capable of sound pressure levels in excess of 150dB Continuous exposure to sound pressure levels over 100dB may cause permanent loss of hearing Use common sense and PRACTICE SAFE SOUND troubleshooting If you experience Signal Processor does not turn on Check that Remote Turn On Wire has 12V a 12V wirehas 12V Ground wire is properly connected Level of sound is low Check that Wiring is not loose or cables misconnected disconnected RCA cables are not faulty Background noise is too high Check that Wiring is not loose or cables misconnected disconnected RCA cables are not faulty MAIN VOL FADER 150M2 LE 430PX Parametrio Equalizer an a see asin er N HI SUB FREQ SUB VOL 4 mwe IsKHz ET i in d dash 4 band parametric aoe ES www pyleaudio com a vV E D congratulations Thank you choosing Pyle Audio and congratulations onjoining a select group of dedicated enthusiasts committed to the very best in mobile sound performance and dependability You are nowthe proud owner of one of the w
3. Subwoofer Volume Control Rotate clockwise or counter clockwise to increase or decrease the subwoofer output level 6 Master Volume Control Rotate clockwise or counter clockwise to increase or decrease the output level After the input gains are properly adjusted with the source unit we recommend that you set your source volume to 1 2 or 3 4 of way up and use the master volume of this EO to control the system volume as its performance is more linear 7 Equalizer Level Controls Rotate clockwise or counter clockwise to boost cut the level of each Bass Mid Bass Mid Hi frequency band by 18aB 8 Subwoofer Channel Outputs RCA cables are used to connect the subwoofer channel amplifier inputs 9 CD and Radio Inputs RCA cables are used to connect your car stereo head unit CD player or other source to either the line or AUX inputs 10 Front and Rear Channel Outputs RCA cables are used to connect the front channel outputs to the front channel amplifier inputs and the rear channel outputs to rear channel amplifier inputs 11 CD Radio Input Gain Control THE CD Radio L R channel can be adjusted from the top cover Turn the knob clockwise to increase the input level or turn counterclockwise to reduce the input level 12 Phase Shift Selector Switch Allows you to select the proper phase of the subwoofer output signal to compensate for the timing differences between the subwoofer output and the front rear output signals el
4. ectrical connection rear RED WIRE ip cs to remote E 358 Fuse 0 5A turn on Iwa Ca 12V Fuse 1A head unit p ae 12V battery BLACK WIRE System wiring basic system application using front rear and subwoofer amps ple430px l D Sa CCMOCICICY CD left andright CD inputs left and right CD outputs from head unit Y J N N REAR CHANNEL N speakers bw i REAR CHANNEL power amplifier P A JN V FRONT CHANNEL N speakers NC R FRONT CHANNEL power amplifier i ANI iE S SUB CHANNEL speakers SUB CHANNEL X R power amplifier system wiring basic system application using a 4 channel amp and subwoofer amp left and right CD outputs from head unit B CaCa aC CeCe C left and right CD inputs L R REAR speakers 0000000 S ooooo0o00 IiE 4 CHANNEL power amplifier L R FRONT speakers od
5. orld s most sophisticated electronics components This Pyle product isthe result of an extensive engineering program with the sole purpose of creating the finest mobile audio experienceimaginable We areconfident that this product will provide you with many years of outstanding musical entertainment specifications Frequency Bands SUB 150Hz LOW 400Hz MID 2 5KHz HIGH 15KHz Boost Cut 18dB Signal To Noise Ratio 110dB REF 1V INPUT Frequency Response 10Hz 15KHz 1dB Maximum Output Voltage 7V RMS Total Harmonic Distortion 0 05 Input Sensitivity 150mV Headroom 20dB Input Impedance t _ 110K OHMS Stereo Separation 82dB 1KHz Operating Voltage 11 15V NEGATIVE GROUND features and controls L inows 4 L indino ple430px qo Nivo 1NdNI ca wi 2 JH PHASE YLE essex and Crossover co al 1 1 1 IC 1 1 10 oe FADER BASS MID BASS SUB FREQ o nS oe vk x rl 1 T a features 1 Input Selector Switch Allows you to select either the radio or CD input 2 Illumination Selector Switch Allows you to select either amber or green color illumination 3 Preamp Fader Control Rotate Clockwise or counter clockwise to adjust the volume between the front and rear outputs 4 Subwoofer Crossover Control Allows you to select your desired crossover cutoff frequency in the 30Hz 250Hz range 5
6. r additional signal processor s Turn the unit on and adjust theinput gain onthe signal processor to matchthe output of the head unit 1 2 or atcenter position isabout 1 Vi Be carefulnot to overdrive the input of your amplifier s or signal processor Adjust each ofthe crossover or equalizer controls to achievethe desired sound characteristics
Download Pdf Manuals
Related Search