SHUTTERBOSS - B&H Photo Video Digital Cameras, Photography
Contents
1. SHUTTERBOSS VERSION II USER MANUAL VELLO INTRODUCTION Thank you for choosing the Vello ShutterBoss This device is more than just a remote shutter release It features many timer functions self timer interval timer long exposure timer as well as controls for the number of continuous shutter trips Powered by two AAA batteries it can take approximately two months of continuous shots with a delay of 5 minutes between exposures and an exposure length of 4 56 You can set the timer delays exposure times and intervals up to 99 hours 59 minutes 59 seconds in one second increments You can select anywhere from 1 to 399 continuous shots or set the device to take an unlimited number of photos The LCD screen has a backlit function for low light conditions The Vello ShutterBoss is great for time lapse recording of blooming flowers astrophotography etc We have added two new features in Ver Il 1 POWER OFF option This feature gives the ability to power the device off to conserve battery life 2 RESET option This feature allows the ShutterBoss to be reset to the default factory settings so that each setting doesn t need to be reset individually SAFETY WARNINGS There are no user serviceable parts inside the device Do not attempt to disassemble or perform any unauthorized modification Do not operate the ShutterBoss in the presence of flammable gas or vapors Do not handle with2. If TIMER ACTIVE is also blinking the timer has released the shutter Press Timer Start Stop if you wish to cancel the timer action If TIMER ACTIVE is not also blinking the shutter has been released manually A manual release can be cancelled by releasing the shutter release button sliding it back from its locked position if necessary 15 oO s ME D SELF LONG INTV No BEEP Activity Indicators CHANGING THE BATTERIES The low battery indicator will blink when battery power is low To change batteries 9 AC I Li D 1 Check that the TIMER ACTIVE and SELF LONG INTV No BEEP RELEASE buttons are not active 2 Turn off the camera and disconnect the ShutterBoss 3 Slide open the battery chamber cover on the back of the ShutterBoss 4 Remove the batteries 5 Wait for the display to go out and install two fresh 1 5V AAA alkaline batteries Low Battery Indicator 16 CARE OF THE SHUTTERBOSS Protect the ShutterBoss Do not drop the ShutterBoss The device may malfunction if subjected to a strong shock or vibration Keep Dry The ShutterBoss is not waterproof Avoid getting the device wet Do not expose to high humidity Avoid Sudden Temperature Changes Sudden changes in temperature such as entering or leaving a warm building on a cold day can cause damaging condensation inside the device Protect the ShutterBoss by placing it inside a carrying case or a sealed plastic bag and allowing it
3. locked If you see the displayed press the X Lock button until the lock icon disappears 3 Use the arrow button to set the cursor beneath LONG Press the left and right v arrows to move the cursor into place 4 Press the SET button to change the Exposure Length setting Use the left and right arrows to move between hours minutes and seconds Use the up and down arrows to change the time values 5 Press SET again to accept your selection 6 Press TIMER START STOP to begin timer 10 Cursor O 2 Tt D SELF LONG INTV No BEEP Hours Minutes Seconds TIMED INTERVALS The ShutterBoss allows you to control the amount of time between a series of shots Choose an interval that is longer than your exposure time from 1 second to 99 hours 59 minutes 59 seconds If using a flash be sure to set an interval that is longer than your flash recycle time 1 After connecting the ShutterBoss to your camera adjust your camera settings Choose your focus mode and set your exposure 2 Make certain that the controls on the ShutterBoss are not locked If you see the displayed press the X Lock button until the lock icon disappears Cursor 3 Use the arrow button to set the cursor A v rows voor the ee ios SES id SELF LONG INTV No BEEP 4 Press the SET button to change the Interval setting Use the left and right arrows to move between hours minutes and seconds Use the up and down arrows to change the time
4. the arrow button to set the cursor a Vus it for setting te delay beneath SELF iin the left and Pa 9 A I L D ith the ShutterBoss you can select a v arrows to move the cursor into place SELF LONG INTV 0 BEEP self timed delay from 1 second to 99 hours 59 minutes 59 seconds in one second PS UIS OFT outton toenanre the Self Timer setting Use the left and right increments arrows to move between hours minutes 1 After connecting the ShutterBoss to and seconds Use the up and down arrows your camera adjust your camera settings to change the time values Choose your exposure mode shutter speed focus mode and shooting mode Do not set the camera s self timer 6 Press TIMER START STOP to begin timer 5 Press SET again to accept your selection 2 Make certain that the controls on the ShutterBoss are not locked If you see the Hours Minutes Seconds displayed press the XX Lock button until the lock icon disappears TIMED EXPOSURE LENGTH The ShutterBoss can control shutter speeds that are much longer than your camera can With the ShutterBoss you can select shutter speeds from 1 second to 99 hours 59 minutes 59 seconds in one second increments The confirmation LED will blink every second during a long exposure 1 After connecting the ShutterBoss to your camera adjust your camera settings Choose your focus mode Set the exposure mode to B bulb 2 Make certain that the controls on the ShutterBoss are not
5. to adjust to temperature changes gradually Avoid Magnetic Fields Strong static charges or electromagnetic fields generated by equipment such as radio transmitters can interfere with the device A strong external static charge can cause unusual characters to display on the screen or may cause the device to malfunction In such a situation turn off the camera disconnect the ShutterBoss remove the batteries and then replace them a few seconds after the display goes out 17 Liquid Crystal Displays The display panel is a liquid crystal display At very low temperatures the display response my become slower And at temperatures higher than 60 C 140 F the display may darken In either case the display will return to normal at room temperature SPECIFICATIONS Supported Cameras See packaging Self Timer Delay Exposure Range Os to 99hr 59min 59s in one second increments Interval Number of Shots 1 399 unlimited Power Source OT EE EE AIN EE 20 to 50 C 4 to 122 F Dimensions Cord Length Approx 33 5 85 cm Weight 18 FCC COMPLIANCE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and
6. values 5 Press SET again to accept your selection 6 Press TIMER START STOP to begin timer Hours Minutes Seconds 11 NUMBER OF SHOTS The ShutterBoss allows you to control the number of shots taken in a sequence You can set the ShutterBoss to trigger the camera shutter up to 399 times Or you can set it to take shots until you tell it to stop By default there will be a one second interval between shots see the previous page 1 After connecting the ShutterBoss to your camera adjust your camera settings Choose your focus mode and set your exposure 2 Make certain that the controls on the ShutterBoss are not locked If you see the displayed press the XX Lock button until the lock icon disappears Cursor 3 Use the arrow button to set the cursor beneath No Press the left and right 9 ua IL I v arrows to move the cursor into place SELF LONG INTV No BEEP 4 Press the SET button to change the number of shots Use the up and down arrows to change the value To set the number of shots to infinite select which is beyond 399 or below 1 5 Press SET again to accept your selection 6 Press TIMER START STOP to begin timer Number Of Shots 12 AUDIBLE BEEP The ShutterBoss will give you an audible beep for the last three seconds of a countdown delay or interval It will also beep to confirm your settings You can turn off the audible beep 1 Make certain that the control
7. wet hands or immerse in or expose to water or rain Failure to Observe this precaution could result in fire or electric shock Keep out of the reach of children This device contains small parts which may pose a choking hazard Observe caution when handling batteries Batteries may leak or explode if improperly handled Use only the batteries listed in this manual Make certain to align batteries with correct polarity Batteries are prone to leakage when fully discharged To avoid damage to the product be sure to remove the batteries when leaving the product unattended for prolonged periods or when no charge remains Do not use or leave the device in conditions of extreme heat severe cold or high humidity Turn off the camera s power before inserting or removing the remote cord Dispose used batteries packaging and old devices in accordance with appropriate local environmental regulations FEATURES DIAGRAM Confirmation LED Display Panel Power On Off Timer Start Stop button Connector Cable Shutter Release Button Eyelet For __ Strap Or Lanyard Backlight Lock Button Set Button Control Selection Button Battery Cover DISPLAY PANEL Exposure Function Number of Shots Function Interval Function Self Timer Function Audible Beep Function ORNE RTS SELF LONG INTV No BEEP Function Cursor Battery Indicator Time Display Audible Beep Indicator LOCK Indicator Numb
8. er of Shots Indicator TIMER ACTIVE Indicator RELEASE Indicator SET Indicator CONNECT TO THE CAMERA The ShutterBoss comes in a variety of models that are compatible with different cameras The only difference in ShutterBoss models is the connector on the end of the cable Your ShutterBoss and camera may look different from those pictured in this guide 1 Make certain the camera is turned OFF 2 Make certain the TIMER ACTIVE and RELEASE indicators are not displayed on the ShutterBoss 3 Move the camera s remote cord socket cover to expose the remote cord jack and connect the ShutterBoss Look for this symbol Many camera manufacturers use it to indicate the jack for connecting remote devices 6 POWER RESET INSTRUCTIONS Press and hold TIMER START STOP for approximately 3 seconds to power the Shutterboss timer on or off Simultaneously press LOCK and TIMER START STOP to clear the current timer information OPERATING INSTRUCTIONS With the ShutterBoss you can release your camera s shutter manually or by using the internal timer Every camera handles remote switches differently Be sure to follow the instructions on using remote switches in your camera s manual as well as the steps in this guide Do not attempt to change any timer settings during exposures or during delay or interval countdowns Manual Release The ShutterBoss can be used manually even when there are no batteries in the dev
9. he warranty provider reserves the right to replace it with a model of equivalent quality and function This warranty does not cover damage or defect caused by misuse neglect accident alteration abuse improper installation or maintenance EXCEPT AS PROVIDED HEREIN THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE This warranty provides you with specific legal rights and you may also have additional rights that vary from state to state To obtain warranty coverage contact the Vello Customer Service Department to obtain a return merchandise authorization RMA number and return the defective product to Vello along with the RMA number and proof of purchase Shipment of the defective product is at the purchaser s own risk and expense For more information or to arrange service visit www vellogear com or call Customer Service at 212 594 2353 Product warranty provided by the Gradus Group VELLO www gradusgroup com A Gradus Group Brand VELLO is a registered trademark of the Gradus Group 2014 Gradus Group LLC All Rights Reserved www vellogear com Gas
10. ice The display panel will be off and no beep will sound Timed Release The ShutterBoss allows you to select any combination of the following Delay time before the shutter is tripped Exposure time or you can set this on the camera Interval the amount of time between a sequence of shots The number of shots to take in sequence You can even set the ShutterBoss to take photos until you tell it to stop MANUAL RELEASE The ShutterBoss can be used manually even when there are no batteries in the device The display panel will be off and no beep will sound To use the ShutterBoss manually 1 After connecting the ShutterBoss to your camera adjust your camera settings Choose your exposure mode shutter speed focus mode and shooting mode 2 Press the shutter release button halfway on the ShutterBoss The camera will focus if set to Auto Focus 3 Press full on the shutter release button to take the photo Release the button to end shooting The shutter release button can also be used to release the shutter while the timer is active The shutter will release and the timer will continue its countdown To lock the pressed shutter button slide the shutter release button forward If your camera is set to Bulb mode the shutter will stay open until you slide the locked shutter button back and release it SELF TIMER DELAYED RELEASE Cursor The self timer on your camera is limited in 3 Use
11. s on the ShutterBoss are not locked If you see the displayed press the Xt Lock button until the lock icon disappears 2 Use the arrow button to set the cursor beneath BEEP Press the left and Or y right arrows to move the cursor into place Cursor 3 Press the SET button to change the Audible Beep setting Use the up and down 9 AC LL m D SELF LONG INTV No BEEP arrows to turn the beep ON or OFF 4 Press SET again to accept your selection Audible Beep OFF 13 BACKLIGHT LOCK BUTTON Press the X Lock button briefly to activate the backlight on the display The backlight will remain lit for about 6 seconds Pressing the button again during backlighting will extend the backlighting for another 6 seconds To lock all the controls except the shutter release button press and hold the XX Lock button until the l icon appears in the display To unlock press and hold the Backlight Lock button until the B icon disappears ACTIVITY INDICATORS TIMER ACTIVE When TIMER ACTIVE is blinking it means the timer is active Do not attempt to change any settings While TIMER ACTIVE is blinking Press Timer Start Stop if you wish to cancel the timer action SET When SET is blinking it means that you are engaged in changing a setting Note the cursor it will confirm which parameter is active Press Set to confirm your setting RELEASE When RELEASE is blinking it means that the shutter is open
12. used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the distance between the equipment and the receiver 19 CAUTION Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Vello may void the user s authority to operate the equipment Limited One Year Warranty This VELLO product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one 1 year from the original purchase date or thirty 30 days after replacement whichever occurs later The warranty provider s responsibility with respect to this limited warranty shall be limited solely to repair or replacement at the provider s discretion of any product that fails during normal use of this product in its intended manner and in its intended environment Inoperability of the product or part s shall be determined by the warranty provider If the product has been discontinued t
Download Pdf Manuals
Related Search