cs 969 quick / smart stop
Contents
1. CREATING MODIFYING DELETING A FILE Starting from the main menu press the FILES menu The files sub menu appears Create Modify Erase Free memory xxx 800 All the submenus of CREATE MODIFY DELETE contain a FILE LIST key which will provide a list of files already saved Touch CREATE then type the reference of your file 8 digits max using the numeric key pad Touch the validation key 928 The message PLEASE WAIT appears for about 1 2 second then the file data screen appears You can modify any of the values using the numeric keypad All the values entered must be validated immediately by touching the Lea key Use the key 5 to move from one value to another The meaning of the values displayed is as follows mould th Moulding thickness at the bottom of the rebate wd Frame width pos Dimension position Internal or external Ign Frame length EXTERNAL DIMENSION INTERNAL DIMENSION Once the values have been entered you can use the OK key to validate the file or choose not to validate it and return to the file menu using the RET key Likewise from the file menu screen you can modify an existing file delete a file or view the file list The files are not necessarily arranged in chronological entry order A deleted file is in fact a file with values set to OOOO this programme function is also found on models CS4095 CS2095 EXECUTING A FILE In the main menu touch EXECUTE If the sto2. ARTICLES LIST ARTICLE TO CREATE ARTICLE S SPECIFICATION DIMENSIONS MOULDING WIDTH FRAME WIDTH FRAME LENGTH MARIE LOUISE FUNCTION 1 UNPACKING THE NUMERIC STOP NS Open the crate and put the NS foot stand into an upright position With a 4mm hex head key unscrew the 4 screws of the 2 foot stand locking plates Pl and P2 Push P1 and P2 right back with a mallet then slide them down to the bottom of each foot Retighten the 4 screws of plates P1 and P2 With a 5mm hex head key unscrew V1 and V2 and put the NS feet in the outside position as shown in figures 3 and 4 ASSEMBLY OF THE NUMERIC STOP NS The NS can only be assembled after the CS 969 has been made level on the ground The right hand extension and its support bracket have been dismantled and the 2 frame fastening screws are used THE FOLLOWING PROCEDURE REQUIRES AT LEAST TWO PEOPLE TO CARRY IT OUT j i a sat P CUTTING TABLE e Take the NS out of the crate and turn it over Place the bed of the NS on bracket E and screw them together 10mm long tubular socket wrench 5mm hex head key without tightening with the 2 screws 2 washers and 2 nuts provided ry T3 Unlock locking screw Z and slide the guide GB of the NS along screws 1 2 3 of the right hand table and the nuts of the 2 ruler supports R1 and R2 Screw 3 should be visible in hole T3 Tighten screws 1 2 3 and V1 and V2 of r
3. rebate and external outside of frame measures unless the external dimension is locked see Parameters section The machine features a cut counter which is incremented each time the blades START a cut To reset to OOOO touch the CUT key This does not reset the general counter to 00000000 dis played on the first screen at start up If STOP OFF is pressed red rotating locking mushroom button the stop returns to its point of origin after unlocking Any mouldings present must be removed If a dimension beyond the stop limits is entered it is automatically reset to the limit position STANDARD SIZES The 969 Quick Stop Smart Stop can also store 80 standard frames identified only by their length and width dimensions The standard frame menu is accessed either via the Main menu or via the Execution menu There are 10 pages of 8 standard sizes All the dimensions can be reprogrammed using the numeric keypad A frame is executed by touching its key the execution screen will appear allowing only the length and width values of the standard frame to be adjusted This allows standard frames to be combined with the SMART STOP measuring function or a stored file MENU MAINTENANCE PARAMETERS In the main menu touch MAINTENANCE to access the parameters SS age UBM pag All the values can be modified There is no need to switch off the power for the new values to be acknowledged RESET MEASURER Press t
4. Remove the alignment thread 2 Insert the plug at the end of the section CONNECTING THE NUMERIC STOP The NS has 3 DIN plugs to be connected to the machine above the front right hand foot N 2 3 FEMALE FEMALE 4P DIN SP DIN USING THE 969 QUICK SMART STOP The operation of the stop has almost no effect on saw operation The only signals exchanged are Disabling stop movement if the blades are moving forward Rebate bottom measurement pushbutton Smart Stop Rebate bottom measurement coder value Smart Stop The 969 Quick Stop Smart Stop can store 800 files comprising An 8 digit reference Moulding rebate bottom thickness accuracy 1 10th mm Frame width accuracy 1 10th mm Frame length accuracy 1 10th mm Dimension position Internal or external The 969 Quick Stop Smart Stop can also store 80 standard frames identified only by their length and width dimensions Using the touch screen The 969 Quick Stop Smart Stop is equipped with an intuitive touch screen for man machine dialogue The operating principle is the same as for the other machines in the range 4095 3099 2095 The screen only displays the information required and the keys represent the only possible choices This makes it much simpler to use as the user is guided When the numeric keypad appears any values changed must be validated If the terminal detects a problem the corresponding message is displayed until the problem 1
5. 5 remedied e g STOP OFF etc At start up the initialisation screen appears programme version screen version number of cuts distance travelled and choice of available languages Zon 2 399 VER hh lt a CE tel 2271 1684424362 tax 733 11644 SE 23 bs 969 SMART STOF uts 100570 SoB Pls 5 864355 __VERSCR 204 00 VERPROG OSa oa When the screen is touched the main menu appears SMART STOP REBATE BOTTOM THICKNESS MEASURER Switch the machine on by setting the main switch to ON If you are using the SMART STOP the following warning message appears if the measurer button is pressed THICKNESS MEASURER STARI POSITION NOT CHECKED YEE PEER gt In this case you will need to remove any moulding and let the measurer position itself against the fixed rule G Now still keeping the measurer button pressed down touch the RESET MEASURER screen key gt If you make a mistake e g a moulding was still in place you can start the procedure again via the MAINTENANCE menu Once the measurer origin 1s set the execute screen will appear when the measurer button is touched ro Gay z Milli heer The moulding measurement will be displayed in the MEASUREMENT key 032 1 for example The measurement is validated by touching the MEASUREMENT key and it will be used to com pute the required position
6. 717160 iS Cassese CS 969 QUICK SMART STOP TECHNICAL AND USER MANUAL MANUEL D UTILISATION amp TECHNIQUE MANUAL DE UTILIZACION Y TECNICO CASSESE SA ZONE INDUSTRIELLE 77390 VERNEUIL PETANG FRANCE 04 2006 Cassese Communication CS 969 QUICK SMART STOP TECHNICAL DATA DIAGRAM PROGRAM UNPACKING ASSEMBLY ADJUSTEMENT CONNECTING USING THE 969 QUICK SMART STOP THE TOUCH SCREEN SMART STOP REBATE BOTTOM THICKNESS MEASURER CREATING MODIFYING DELETING A FILE EXECUTING A FILE STANDARD FRAMES MENU MAINTENANCE PARAMETERS Cassese Communication 04 2006 2 3 4 TECHNICAL DATA Dimensions length 2390 mm width 512 m height 1130 mm Power supply 380 V 220 V distributed from the 45 or multi angle saw 969 Automatic stop measuring function See diagram below Thickness measurement without rebate Max moulding thickness check 150 mm Options Length measurement greater than 1860 mm on request Bar code scanning PC connection MOULDING WIDTH MINI 10 INTER 2160 maxi 100 int min with moulding 10 10 inter MOULDING CUTTING PLANE MOULDING WIDTH MAXI 150 INTER 1860 max with moulding 150 100 mini with moulding 150 150 inter MOULDING CUTTING PLANE PROGRAM OF QUICK SMART STOP CS 969 STANDARD PLAY STOP OFFSET LOCK EXT DIMENSION MAINTENANCE STANDARD SIZES EXECUTE INCREASE PLAY MAIN MENU ARTICLES FILE CREATE MODIFY ERASE
7. he measurer button and this key simultaneously to reset the meas urer origin 1f it is incorrectly set STANDARD PLAY Type the play value allowance you wish to add automatically for internal dimension positioning e g 1 5 mm Stop mechanical offset Dimension at which the automatic stop is initialised each time the power is switched on and the EXECUTE key is touched for the first time This dimension can be checked by cutting a moulding at 45 and measuring its thickness without rebate If necessary this dimension can be adjusted each time a stop or coder 1s removed In this case check that the stop initialises approximately 2 3 cm beyond the proximity detector of the origin take up area LOCK EXT SIZE Type the value 1 if you do not wish the operator to be able to work with external dimensions the INTER EXTER keys will be disabled To release type the value 0 Pin code Reserved for maintenance
8. p is not yet initialised it will return to its origin point stop offset This will be the one and only time that automatic initialisation occurs after switching on after this the position is set automatically The first execution screen is then displayed The file parameters displayed in this screen are the last parameters created modified listed or executed This means that after a machine power failure you do not need to re enter a reference before resuming work Also you can list the file that you are inter ested in and then execute it without having to call up its reference You can call up a reference for execution via the FILE key You can modify the execution pa rameters by touching GIVE SIZES or STD SIZES This does not alter the saved parameters but only those that are executed In every case The dimension depends on the moulding thickness and the dimension position Internal or Ex ternal If the dimension is INTERNAL the standard play allowance is automatically added see how to set this play in Parameters section The play for the cut to be made can be modified by pressing the ADD PLAY key on the screen The minimum and maximum measure capacities depend on the moulding thickness and the dimension position internal external Use the dimension keys that are shown next to the length and width of the frame to switch from short to long dimension Use INTER EXTER to switch your choice between internal
9. uler supports 1 and R2 with a 4mm hex head key 2 ADJUSTMENT OF THE NUMERIC STOP NS Slide the NS head towards the cutting table and position plate GA right next to screw VBI see fig 4 PR reference posi tion Tighten screw VB1 with a 4mm hex head key Repeat for the following screw VB2 and so on for the other screws up to the end of the NS Lining up the stops Pass the thread under the head of the NS against the inner face of the guide GB Put in one screw and two nuts at one end of the thread looped and hook to the left tip of the left extension stop Repeat for the other end of the thread Adjust the length of the thread so as to create tension when it is hooked to the right tip of the NS guide Increase the tension in the thread by tightening the nuts with a 10mm open end Proper adjustment 1 The thread is stretched uniformly on the right and left stops 2 There is no gap in the STOP MACHINE joint J If this is not the case move the NS sideways until the thread is fully stretched on the two stops and the gap in joint J disappears Perpendicular level base Horizontal Stop level Levelling With a 19mm open end wrench adjust the NS levels in relation to the machine table by screwing and unscrewing nut EH of the NS feet Check the levels with a ruler After adjusting level alignment tighten the nuts of bracket E permanently 10mm tubular socket wrench 5mm hex head key
Download Pdf Manuals
Related Search