6002TA User Manual B
Contents
1. 6002TA terminal adapter base Plug the cable from the terminal adapter base into the expansion connector on the telephone The polarization tab on the plug must fit into the opening on the side of the phone connector 5 Snap the terminal adapter base onto the phone The base may be rotated for wall mounting 6 Replace the retaining screw required for UL compliance Connecting the POTS Device Connect the analog telephone device to the jack on the back of the base using a standard 4 or 6 conductor cable WARNING The 6002TA is intended to connect to local analog POTS telephone devices via relatively short less than 300 feet inside plant cabling Do not connect to wiring that extends outside or between buildings or that may be subject to electrical hazards such as lightning or power line crosses Do not connect to a telco network telephone line Damage to the POTS port may occur 8 Tone Commander 6002TA User Manual POTS Port Options The following options can be configured from the POTS Port Options menu e Ring Control e Call Waiting e POTS Line Privacy e POTS Originating Call Appearance POTS Port Options Menu You can enter the POTS Port Options menu at any time Setup Press the Setup key SETUP MENU INSTL ADMIN USER POTS a Select POTS Pars PORT OPTIONS RING PRIV CALLWT ORIG Tone Commander 6002TA User Manual POTS Ringing Control You can control the audible ringing at the analog tele2. menu select ORIG Setup gt POTS ORIG The current outgoing call appearance will be shown in the display and the CA DN key will alternately flash red and green POTS ORIGINATING CA CAI If you want to use a different call appearance press another CA DN key Status indicators for available CA DN keys will be green When finished press the Done key to return to the POTS Port Options menu or the Setup key to exit Setup Mode Tone Commander 6002TA User Manual 13 AppendixA Warranty and Service Tone Commander Product Warranty For a period of one year from date of dealer purchase but not to exceed 16 months from date of manufacture Tone Commander Systems Inc Tone Commander warrants its products to be free from defects in material and workmanship under conditions of normal use and service Tone Commander shall at its option repair or replace any defective product which in its opinion has not been misused damaged or improperly installed Repair or replacement under this warranty will be performed at Tone Commander s factory Authorization must be obtained from Tone Commander prior to returning a product for repair Freight must be prepaid for all units returned to Tone Commander Units repaired under warranty will be shipped UPS Ground or equivalent freight prepaid by Tone Commander Products that are older than the warranty period but less than 7 years old or still manufactured by Tone Commander may be
3. TONE COMMANDER 6002TA Analog Port Terminal Adapter User Manual TONE COMMANDER Contents Introduction ss PTA T gcdecccacs osbcctecsvacccdoathieansazecevaaa Operation ee NE tet decade de Placing a Call nennen ser Answering a Call ss Switching a Call Between the POTS Port and Speakerphone or Handset 0 cher add BA KARNA KAKA MERA eek in Call Waiting satser EA AASE sn durs S modes fe eat eter aed Conferencing Calls AATA Transferring Galls 3 322422 AM ann ae breite ine Using an Analog Modem or Fax Installation ul 2 0 He ee HER SN NEAR SES KARA snus aa entretenue Mounting the Base nu na rennen Connecting the POTS Device ssssssssssesssrrsssrsssesssrsssssrsssrrrennr ns nn nenn POTS Port Options sers ee eben POTS Port Options Menu s sserrrrsssesrerrsssensenrnernrrrensn nere rr seen sr nn nr rr rr nenn POTS Ringing Control ss POTS Line Privacy ua ee are aa POTS Line Call Waiting Alert ss sees ss ser sn seen sn nn POTS Line Originating Call Appearance nenne Appendix A Warranty and Service Appendix B Specifications sis Factory Default Settings Appendix C UL FCC Statements issus Tone Commander 6002TA User Manual ii Tone Commander 6002TA User Manual Introduction The Model 6002TA Analog Port Terminal Adapter adds one POTS Plain Old Telephone Service port to a Tone Commander 6210 or 6220 ISDN telephone
4. acteristics 0 dB Transmit Loss 3 dB Receive Loss 1 dB 300 3000 Hz Echo Return Loss gt 12 dB 600 or 900 ohms Power Requirements 24 to 56 5 VDC powered through 6210 or 6220 ISDN phone Typical 1 5 W idle 3 5 W off hook including 6220T ISDN phone Tone Commander 6002TA User Manual 15 Standards Compliance FCC Part 15 Part 68 UL cUL 60950 Section 508 1194 23 a non acoustic connection point for TTYs Physical Dimensions 6 4 W x 5 7 D x 2 4 H replacement base for 6210 6220 ISDN phone Weight 0 5 Ib Environmental Operating Temperature 32 to 104 F 0 to 40 C Storage Temperature 32 to 122 F 0 to 50 C Humidity 5 to 95 non condensing 16 Tone Commander 6002TA User Manual Factory Default Settings Parameter Ringing Control Privacy Call Waiting Originating Call Appearance Default Value Always Ring all call appearances Off Disabled Call Appearance 1 Tone Commander 6002TA User Manual 17 Appendix C UL FCC Statements Important Safety Instructions 1 Never install telephone wiring during a lightning storm 2 Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations 3 Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface 4 Use caution when installing or modifying telephone lines When using your telephone equipment basic safety precauti
5. e to answer the call The originating call appearance indicator on the 6210 6220 will light amber and no calls can be placed from the 6210 6220 while the POTS port remains in use The 6210 6220 has ring delay settings independent from the POTS port Calls may ring at the 6210 6220 before ringing at the POTS port if the POTS port has a longer ring delay If multiple calls are ringing the first call appearance to ring at the POTS port is answered when going off hook on the analog phone Tone Commander 6002TA User Manual 3 Switching a Call Between the POTS Port and Speakerphone or Handset Use the 6210 6220 Spkr key or hookswitch to switch a call from the analog phone to the 6210 6220 speakerphone or handset The call will be disconnected from the POTS port To switch the call back to the analog phone hang up the analog phone first go off hook then press the key on the analog phone You will not hear dial tone and the tone will not be sent out over the ISDN line You can continue to switch the call between the phones regardless of where the call was answered This feature is disabled if Privacy is set to ON see page 11 Call Waiting Most telephones have a Flash key that sends a timed hookflash This key is used during call swapping conferencing and transferring If your analog phone does not have a Flash key you can send a flash by quickly pressing and releasing the hookswitch When the POTS port is in use and another ca
6. fer The ISDN conference feature provisioned on your line must support implicit transfer capability Otherwise the two remaining parties will be disconnected when you hang up If the second party is busy or you want to abort the transfer hang up without flashing Your phone will ring and you will be reconnected to the first party when you answer Tone Commander 6002TA User Manual 5 Using an Analog Modem or Fax An analog modem or fax device may be connected to the POTS port For this application If you have a dedicated call appearance directory number for incoming modem or fax calls set ringing control for the POTS port to ALWAYS on that call appearance page 10 for immediate answer by the fax or modem device Set all other call appearances to NEVER Set the ringing control for the 6210 6220 to NEVER for the fax modem call appearance Setup gt USER gt RING gt CONTROL Set the fax modem call appearance as the primary originating POTS call appearance page 13 Privacy must be set to ON page 11 Disable POTS port call waiting page 12 Using a Text Telephone TTY A text telephone can be connected to the POTS port allowing you to answer text calls After answering a call on the ISDN phone you will hear a TTY alert tone from the calling party Go off hook and dial on the text telephone to switch the call from the ISDN phone For TTY applications If you have a dedicated call appearance directory numbe
7. for standard telephones fax machines or analog modems Adapter circuitry is housed in a telephone base that replaces the standard base POTS port features include independent ring delay settings call waiting tone and caller ID display support a privacy option to prevent line access from the 6210 6220 when busy call transfer and conference and originating call appearance selection Typical Applications Cordless handset or headset calls can be originated or answered from a cordless phone or cordless headset phone Call transfer and conference features are provided On hook and off hook call waiting caller ID displays are supported as well as call waiting tones Conference Room Speakerphone use high performance analog conference room equipment such as a Polycom SoundStation on your ISDN line Calls can be dialed or answered on either the ISDN phone or the conference room speakerphone and easily switched between devices Analog Modem data rates up to 56Kbps for outgoing calls may be supported depending on your modem and the connecting party Call waiting tones may be disabled to ensure data integrity Fax your fax machine can answer and originate calls on your primary directory number or any other number provisioned on your ISDN line Privacy options are provided to ensure reliable fax transmission Answering Machine your answering machine can answer calls to any number provisioned on your ISDN line Separate
8. g other information the FCC Registration for this equipment You must upon request provide this information to your telephone company The following jacks must be ordered from the telephone company in order to interconnect this product with the public communication network RJ49C If your 6210 6220 or 6002TA causes harm to the telephone network the Telephone Company may discontinue your service temporarily if possible they will notify you in advance But if advance notice is not practical you will be notified as soon as possible You will be informed of your right to file a complaint with the FCC Your telephone company may make changes in its facilities equipment operations or procedures that could affect the proper functioning of your equipment If they do you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service The 6210 and 6220 are hearing aid compatible HAC per Section 68 316 FCC Rules and Regulations If you have trouble with the 6210 6220 or 6002TA please refer to the Troubleshooting section in the 6210 6220 manual or contact us at the address listed on the back of this manual for information on obtaining service or repairs The telephone company may ask that you disconnect the telephone from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning NOTE This equipment has been tested and found to comply with the lim
9. iceman when some service or repair work is required Opening or removing covers may expose you to dangerous voltages or other risks Incorrect reassembly can cause electric shock when the appliance is subsequently used 15 Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions A When the power supply cord or plug is damaged or frayed w If liquid has been spilled into the product O If the product has been exposed to rain or water U If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation E If the product has been dropped or the case has been damaged F If the product exhibits a distinct change in performance 16 Avoid using a telephone other than a cordless type during an electrical storm There may be a remote risk of electric shock from lightning 17 Do not use the telephone to report a gas leak in the vicinity of the leak SAVE THESE INSTRUCTIONS Tone Commander 6002TA User Manual 19 FCC Requirements The Tone Commander Models 6210T 6210U 6220T and 6220U with an attached 6002TA comply with Part 68 of the FCC Rules The label affixed to this equipment contains amon
10. its for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense 20 Tone Commander 6002TA User Manual Tone Commander 6002TA User Manual 21 22 Tone Commander 6002TA User Manual TONE COMMANDER 13 102874 Rev B 2003 11609 49th Place West Mukilteo WA 98275 4255 800 524 0024 425 349 1000 Fax 425 349 1010 www tonecommander com
11. ll rings a call waiting tone and or a caller ID display may be sent to the analog phone Press the Flash key on the analog phone to place the current call on hold and answer the incoming call Swap between the calls by flashing Call waiting may be set for caller ID call waiting tone only or disabled see page 12 4 Tone Commander 6002TA User Manual Conferencing Calls Press the Flash key on the analog phone to place the current call on hold and originate a new call Dial the second party After the second party answers flash again to conference all parties together If the second party is busy does not answer or does not want to join the conference hang up Your phone will ring and you will be reconnected to the first party when you answer To add another party to the conference flash again Dial another party as above The number of parties that can be in a conference is determined by your ISDN line provisioning from your service provider typically 3 or 6 Transferring Calls Calls can be transferred by establishing a conference call then removing yourself from the conference After establishing a call press the Flash key then dial the second party Any time after the second party begins to ring you can flash to conference all parties together then hang up to remove yourself from the conference You can wait until the second party answers to announce the call or flash and hang up immediately for an unscreened trans
12. ons should always be followed to reduce the risk of fire electric shock and injury to persons including the following 5 Read and understand all instructions 6 Follow all warnings and instructions marked on the product 7 Unplug the line cord before cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning 8 Do not use this product near water for example near a bathtub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool 9 Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product 10 This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your dealer or local power company 11 Do not allow anything to rest on the power cord Do not locate this product where the cord will be abused by persons walking on it 12 Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock 13 Never push objects of any kind into this product through any openings as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock Never spill liquid of any kind on this product 18 Tone Commander 6002TA User Manual 14 To reduce the risk of electric shock do not disassemble this product but take it to a qualified serv
13. phone device for each call appearance Similar independent settings in the User Options menu Setup gt USER gt RING gt CONTROL control ringing at the 6210 6220 telephone refer to the 6210 6220 User Manual Call appearances set to ALWAYS will ring immediately at the POTS port NEVER completely disables ringing at the POTS port for the call appearance WAIT delays ringing at the POTS port for 2 to 7 ringing cycles 6 seconds per cycle When using a cordless phone on the analog port select ALWAYS for primary call appearances and NEVER for secondary or shared call appearances You can select a WAIT option on primary call appearances when the analog phone is used as a backup answering position set the POTS port ring delays longer than the 6210 6220 delays to ensure that calls always ring at the 6210 6220 first Note You cannot answer a call on the POTS port unless it is ringing ring delays have timed out For fax or modem applications select ALWAYS for the fax call appearance and NEVER for all other call appearances Set the 6210 6220 ringing for the call appearance to NEVER fax modem calls will only ring at the POTS port A From the POTS Port Options menu select RING Setup gt POTS gt RING All multifunction keys that are programmed for call appearances or DSS will have a steady green indication 177 Press a lit key to view its current POTS ring control setting The key s indicator will alternately fla
14. r for TTY calls set ringing control for the POTS port to ALWAYS on that call appearance page 10 for immediate answer by text telephone Set all other call appearances to NEVER If you do not have a dedicated TTY call appearance and want to answer calls on the ISDN phone set ringing control for the POTS port to NEVER or WAIT2 7 for all call appearances Privacy must be set to OFF page 11 Disable POTS port call waiting page 12 You may want to create a phone directory entry on the text telephone to simplify call switching This entry should contain only the character Tone Commander 6002TA User Manual Telephone operating software must be version 01 05 xx or higher to support the 6002TA To view the installed software version select VERS then S W from the Administration Options menu Setup gt ADMIN gt VERS gt S W If your phone s software version is lower than 01 05 xx call Tone Commander at 800 524 0024 to request an update Mounting the Base 1 Disconnect the line cord from the telephone Power must be disconnected before installing the 6002TA Wait 10 seconds after disconnecting power before proceeding 2 Remove the retaining screw in the center of the base 3 Press the top of the tall edge of the base to disengage the snap tabs then lift the original base from the telephone body Do not touch the expansion connector Tone Commander 6002TA User Manual 7 4 Replace the original base with the
15. repaired at the factory for a flat rate charge Repaired out of warranty units are warranted for 90 days from the date of repair The repair or replacement of a product under this warranty represents the entire obligation of Tone Commander Tone Commander shall not be liable for any special or consequential damages resulting from or caused by any defect failure incapacity or malfunction of any of its products The foregoing express warranty is in lieu of all other warranties express or implied including but not limited to any implied warranty of merchantability fitness or adequacy for any purpose or use quality productiveness or capacity Tone Commander to the extent permitted by law hereby disclaims all such other warranties 14 Tone Commander 6002TA User Manual Appendix B Specifications Contents of Shipping Container 6002TA telephone base Manual Compatibility 6210T 6220T 6210U or 6220U ISDN phones may require firmware upgrade May not be used with 6030X 30 Button Expansion Module or 6001TA Terminal Adapter for TAPI Capacity Supports up to 3 standard analog telephone POTS devices Connector Arrangement One RJ 11 6 position modular jack Battery Feed 48 V on hook 50 mA maximum off hook loop current 1000 V minimum isolation from primary ISDN power Ringing 20 Hz 70 Vrms nominal Maximum Load REN 3 Maximum Recommended Loop Length 300 ft 100 M with 24 26 AWG inside wiring only Transmission Char
16. ring delays may be programmed on the analog port to allow calls to be answered on the ISDN phone before the answering machine picks up Tone Commander 6002TA User Manual 1 TTY the analog port provides a standard non acoustical connection point for TTY teletypewriter devices that meets the accessibility requirements of Section 508 for communication disabled users You cannot place a modem or fax call and a voice call at the same time only one active call is allowed See page 6 for modem and fax application settings 2 Tone Commander 6002TA User Manual Operation Placing a Call Go off hook on the analog phone wait for dial tone then dial the called number The originating call appearance indicator on the 6210 6220 will light amber while that line is in use by the POTS port The call appearance selected for originating POTS calls see page 13 is used if idle If this call appearance is in use another primary originating call appearance will be used if available Only one call can be active at a time Calls cannot be placed on the POTS port if the 6210 6220 is on an active call When the POTS port is busy no calls can be placed from the 6210 6220 the display will show ANALOG PORT IN USE if you attempt to place a call from the ISDN phone Answering a Call Call appearances will ring at the POTS port after the selected ring delay see page 10 unless the ring delay is set to NEVER Go off hook on the analog phon
17. sent to the POTS port when it is active and another inbound call arrives at the phone For fax or modem applications select DISABLE to prevent interruptions during a call Your analog phone must have a caller ID display and support call waiting caller ID CIDCW for the CALLID function to work Call waiting tone may still be available if provided by the ISDN network A From the POTS Port Options menu select CALLWT Setup gt POTS gt CALLWT The current call waiting alert setting will be shown in the display CALL WAITING CALLER ID CALLID TONE DISABLE A Select one of the displayed options CALLID calling party ID is sent to the analog telephone device if provided by the ISDN network Your POTS phone must be CIDCW compatible TONE waiting calls are indicated by an alert tone DISABLE call waiting alerting is disabled Done When finished press the Done key to return to the POTS Port Options menu or the Setup key to exit Setup Mode 12 Tone Commander 6002TA User Manual POTS Line Originating Call Appearance This option selects the primary call appearance used for outgoing calls from the POTS port If the selected call appearance is busy when placing a call another call appearance may be used if available For fax or modem applications you can assign a secondary directory number if provisioned on your line for outgoing fax or modem calls a Done fo From the POTS Port Options
18. sh red and green KEYOLSALWAYS RING ALWAYS NEVER HAITZ WAITS KEYOL ALHAYS RING HAITA WAITS WAITE WAIT 10 Tone Commander 6002TA User Manual A If you want to change the setting for the selected key select ALWAYS NEVER or WAIT2 WAIT7 Done Press the Done key to return to the POTS Port Options menu or the Setup key to exit Setup Mode POTS Line Privacy The Privacy setting determines whether phone and POTS calls are mutually exclusive or if they can be swapped between the handset POTS port and speakerphone With Privacy off an active call can be freely passed between the handset speakerphone or POTS port by using the hookswitch or Spkr key With Privacy on an active call cannot be passed between the handset speakerphone and the POTS port Set Privacy ON if a fax or modem is connected to the POTS port and OFF for most other applications A From the POTS Port Options menu select PRIV Setup gt POTS PRIV The current Privacy setting will be shown in the display POTS LINE PRIVACY OFF ON BEE A Select ON to enable Privacy or OFF to disable Privacy Done When finished press the Done key to return to the POTS Port Options menu or the Setup key to exit Setup Mode Tone Commander 6002TA User Manual 11 POTS Line Call Waiting Alert The Call Waiting option determines whether CIDCW Calling Identity Delivery on Call Waiting signaling Call Waiting tone only or no signaling will be
Download Pdf Manuals
Related Search