Home

REDMX 1.06 USER MANUAL - Techni-Lux

1. Press the Qlist button at the top of the editor to activate the cue list window By selecting one or more cues and moving the encoder wheels it is possible to modify the Delay Fade in Wait and Fade out times of each cue if you omit the Wait and Fade out times the cue continues to control the channels until a second cue intervenes or the Release playback is performed Size100 Menu store 1 store palette 2 store cue Cue list window Editing a cue From the cue list display windows Qlist Chase Sequence or Live windows select the cue you wish to edit and press the Load key in this way a copy of the cue in question is loaded into the editor Thanks to the editor it is now very easy to perform the required editing tasks Finally press the Update key to substitute the original cue Palette Palettes are predefined memories which speed up programming each fixture usually already has some predefined palettes in the fdf file but the user can create new personalised ones The preparation of pan tilt palettes is very useful in that once having finished preparing the palettes fixture pointing is done by simply by selecting the fixtures concerned and then clicking on the palette of the desired location IMPORTANT it is useful to program a show by using the palettes because the time spent preparing the palettes is recovered with interest during the programming phase which entails selecting the fixtures individual or in gro
2. e Orange not all fixture group parameters are under the editor s control Off the editor does not control any parameter The right led indicates whether the fixture group is selected or not In the case of the groups it can also turn yellow to indicate that the group has been partially selected By pressing the Fixt Grp button you switch from fixture to group display and vice versa The Clear key deletes all editor content of the selected fixtures Pressing the same key twice in quick succession deletes ALL editor content The wheels enable you to set or edit the attribute values of the selected fixtures The left buttons Intensity Colors allow you to scroll through the attributes which are controlled by the wheels The trackball is always active on the pan and tilt of the selected fixtures ee ex 419 20 err 40ex __ scroller 0 Editor fixture display mode Editor group display mode Saving a cue When you want to save a new cue press the Store key to activate the Store menu and then select the Cue button doing this will add a new cue to the current playback in which the contents of the editor will be copied Pag 14 RedMx 1 06 WARNING normally the programming of a cue begins by selecting the fixtures involved and pressing the Locate key in order to set all the fixture attributes to a defined value Only in advanced use for expert users it is possible to program the cues by leaving Empty attributes
3. the context specific menu we will find the new Ls 40 ex fixture in the RedLighting brand Fixtures patch This window enables you to tell the console which and how many fixtures are involved in the show and the information related to their dmx addressing Pressing the Address Patch button from the Setup Menu activates the patch window This window is divided into two sections the left section allows us to navigate in the fixtures library while the right section show the fixtures which have already been added to the show enabling us to edit them For example if we wanted to add 8 identical fLs 40 ex fixtures connected to the DMX 2 line and mapped next to one another starting from the dmx 120 addressing we would first have to select the RedLighting button on the left hand side of the window and then the Ls 40 ex button the Add fixtures window will appear and using the encoder wheels we will set 8 in the Fixtures to add field 2 in the Dmx universe field and 120 in the Dmx start add field finally we will have to confirm the data by pressing the Add fixtures button Once this has been completed the Add fixtures window disappears and the right hand side of the Address patch window is populated with 8 buttons one for each fixture added Fixtures to add Dmx universe Fixture ID Dmx start add Brand scroll Pato Scroll Fixture to add Fixture ID Dmx Universe Start address Inserting new fixtures in the show Address patch window populated
4. Cue selection leds red selected off not selected 3 Execution led off cue not in execution yellow cue execution completed red in execution 4 Delay time in seconds 5 Fade in time in seconds 6 Delay Fade in timeline bar Cue list in sequence mode Buttons Unselect all Deselects all Qlists Lock when activated to edit the current glist a clear command is needed this can be given via the Se ect button otherwise simply trigger a glist to make the cue list current Qlist Chase Sequence Live cue list mode selection buttons EDITOR recalls the editor window Link Next cue button disabled in this mode Wheels The wheels are used in two separate ways if one or more cues operating on the wheels are selected the Delay e Fade in times are set otherwise the wheels allows you to set the Master Size Master Speed Master Intensity The fourth wheel is always used for window scroll IMPORTANT during playback it could be useful to use the wheels to regulate in real time the amplitude Master Size and the speed master Speed of the effects of the cue or the intensity of the dimmer Master Intensity These three values are not saved on the disk and every time the cue list is activated they return to their default values Pag 32 RedMx 1 06 Live mode A cue list in Live mode allows you to activate single cues directly from the touchscreen by pressing a button of the window a trigger is sent to the corres
5. Opens the browser to allow loading an existing fxr or fdf file Save Saves all changes made to the current file Save As Opens the digital keyboard to save another copy of the current file under a new name Edit Dmx Ch Allows to change the number of DMX channels of the fixture Pag 54 RedMx 1 06 6 SMPTE TIMECODE The SMPTE timecode is a signal which contains a time identification in the hours minutes seconds frame format it was invented in the cinematographic industry to synchronise audio and video and is ideal for solving general synchronisation problems The console is capable of receiving a SMPTE signal generated by a SMPTE master the device which stores the reference clock for synchronisation and activating certain events at predefined times smptet 1 Selection led Off not selected event Red selected O 1 5 3 Trig glist 2 cue 1 event O 1 9 1 Trig glist 2 cue 2 2 Trigger led Green triggered event Off not triggered event 3 Event activation times in Hours Minuts seconds Frames 4 Real time smpte clock Hours Smpte window Buttons Edit puts the list in edit mode When the Edit button is active you can edit the list eliminating or editing the activation times of single events Record puts the list in record mode When the Record button is active all the events which occur in the console are added to the list limited to the types recognised by the programme Play puts the list in play mode W
6. are free the editor is not controlling them e red all parameters associated to the wheel are controlled by the editor e yellow only some parameters associated to the wheel are controlled by the editor the remaining are Empty Group display The groups window is identical in both form and features to the fixtures window except for the fact that the selection is made for groups by pressing a group button all the fixtures therein can be alternately selected and de selected The organization of the fixtures into groups is particularly useful when a show includes many fixtures and these are often managed together in recurring groups As for the fixtures each group button has two leds the first informs us on the status of the channels when switched off all parameters of all the group fixtures are Empty when red all parameters of all the group fixtures are controlled by the editor for all other cases the led is orange The context specific menu is identical to the context specific menu of the fixtures window with the exception of the Pag 19 RedMx 1 06 Select Range button which does not appear here scroller 0 Group display editor mode Create edit a group To create a new group you must select the fixtures that will be part of the group press the Group button on the Store Menu recall by pressing the Store key and then type the name of the new group to be created using the virtual keyboard IMPORTAN
7. doubt do not use the appliance and contact an authorised assistance centre The packaging plastic bags polystyrene foam nails etc must not be left within reach of children as they are potential sources of danger Avoid flammable liquids water or metal objects from entering the appliance In the event of liquid spillage onto the appliance disconnect the power supply immediately Do not disassemble or modify the appliance Do not install this appliance outdoors directly exposed to rain or moisture Avoid using the appliance e In places subject to excessive moisture e In places subject to vibration or possible knocks e In places at temperatures above 45 or lower than 2 C Do not operate the appliance before it has reached its ambient temperature to avoid condensation Never attempt to repair the machine yourself Repairs carried out by inexperienced people may cause damage or serious malfunctioning Consult your nearest authorised Technical Service Centre When performing any operation observe all safety regulations in force in the country of use Console Specifications Pag 5 RedMx 1 06 INTERFACE e 7 inch 800x480 pixel touchscreen color monitor for a powerful and intuitive graphical interface e 2 backlit LCD Displays with 72 characters 2 lines x 36 characters to display the configuration of the sliders e 12 led buttons for direct access to playback and programming functions e 2 Sliders with led button i
8. equal to the Fade out e At the Delay Fade in stage the entrance stage of the cue is completed all LTP and HTP attributes with values other than zero and not Empty will have reached the final value o At the Wait Fade out stage all the HTP attributes with values other than zero and not Empty will have completed the fade out and will be at zero value e Once the fade in is completed if the Link next cue button is active the next cue will automatically receive a trigger otherwise all outputs remain the same until the following trigger arrives Wait and Fade out times are optional if not inserted they are considered to be equal to Delay and Fade out times HTP fade out Value controlled by next cue amp HTP fade in time _ OoOo Wat L ei out Next trigger Fade in and Fade out trend in time Pag 29 RedMx 1 06 I Cue list mode selection buttons 2 Cue selection leds red selected off not selected 3 Execution led off cue not in execution yellow cue execution completed red in execution 4 Delay time in seconds 5 Fade in time in seconds 6 Wait time in seconds means value not inserted 7 Fade out time in seconds means value not inserted 5 Delay Fade in timeline bar 9 Wait Fade out timeline bar Size100 Cue list in Qlist mode Buttons Unselect all Deselects all cues Lock when activated to edit the current glist a clear command is needed this can be done via the Sel
9. in the library palettes cannot be higher than 1024 The next paragraphs contain a step by step explanation on how to create a new fdf file Parameters window Open the Fixture builder programme and press the Add parameters button The number of DMX channels that form the fixture has not yet been defined therefore the digital numeric keyboard will appear asking to type in a value Insert the number of DMX channels for the fixture and confirm The parameters selection window will open select the features included in the fixture If the fixture includes parameters which are not listed choose a parameter with a similar function to be subsequently renamed Use properly the 8 bit and 16 bit buttons to select the size of the feature Please remember that this operation does not have to be completed at once it can be resumed modified reduced or expanded at any time Once completed press OK Next time the parameters window will be opened all previously set parameters will be Pag 50 RedMx 1 06 displayed Data can be edited by clicking on the different fields and using the wheels On the top part of the screen the following buttons are displayed Move up Move down Delete Parameter Rename parameter The Add parameter button goes back to the parameter selection window where more parameters can be added IMPORTANT please remember to carefully check the Htp Itp value Throughout several processes the console uses different computi
10. internal memory and makes it available for Paste operations The led indicator on the Paste button becomes green to signify that the Paste buffer now contains a path Paste This button is used together with the Copy brand and Copy file buttons to perform Copy and Paste operations If the led indicator is turned off the Paste buffer is empty and therefore it cannot be used Copy and Paste operations are primarily used to move a file from one brand to another or from one disk to another Internal Disk from the context specific menu Sets the internal disk as current disk and displays the list of available brands USB Disk from the context specific menu Sets the USB drive as current disk and displays the list of available brands New brand from the context specific menu Activates the digital keyboard to create a new brand on the current disk Rename brand from the context specific menu Activates the digital keyboard to allow renaming the current brand Rename file from the context specific menu Activates the digital keyboard to allow renaming the current file Erase Brand from the context specific menu Completely erases after asking to confirm the current brand and all files contained in it Erase file from the context specific menu Completely erases after asking to confirm the current file Pag 48 RedMx 1 06 Diagnostic IMPORTANTE the diagnostic programme interrupts all processes including data transf
11. means that the dmx channels ranging from 101 to 124 are used to control the intensity SS i master of all 24 console playbacks and the dmx channels ranging from 125 to 148 are used to send them Trigger and Release Total playbacks to map i commands Dmx Start Address Go Release Dmx Start Address 125 First Playback Playbaeks Count Start Address Go Rely Start Add Dmx In Playbacks Configuration window Window buttons and fields Dmx In Enable Dmx playbacks control global enable Pag 59 RedMx 1 06 Dmx In Disable Dmx playbacks control global disable If this button is on the console will ignore all the rest of the configuration and the playbacks control by dmx input is inhibited Go Rel Enable Trigger and Release receive command enable Two dmx channels for each dmx controlled playback are used if this button is selected Go Rel Disable Trigger and Release receive command disable Only the intensity master of playbacks is controlled if this button is selected OK If the new configuration is error free it will be activated and saved on the disk and the configuration window will be closed otherwise an error message will appear Cancel It aborts all the changes made and goes back to the Setup Menu First playback to map This is the first playback that you will control by the external Dmx device You can control up to 24 Playbacks Total playbacks to map This value is the total number of playbacks
12. of new cues happens when the slider passes through 0 To regain control of the cues which are active in a bank other than the current one you must activate the bank in question crossing the old controller value with the slider Pag 37 RedMx 1 06 5 SETUP Setup and utility functions can be accessed from the console Setup menu To access the Setup menu press the Setup button which always appears in the context specific menu A brief overview of the single functions is given below Setup menu Address patch Allows access to the patch window which enables to add or take out fixtures from the configuration of the show and set their dmx addresses General options Allows to set up general options which modify some specific behaviour of the console Fixture configuration Allows to edit the configuration of fixtures used in the current show All changes applied through this function only affect the current show leaving the fixture library unchanged Controller configurations Configuration and personalisation of all Controllers Pan Tilt options Allows to invert and swap the Pan and Tilt function of the show s fixtures Artnet configuration Configuration of Ethernet port and Artnet connector Backup restore For managing and restoring saved show files both from internal memory and USB drive Library manager Manages the fixture library Allows to import and or export single files or folders from the internal memor
13. of the channel to one another so that if the last cue were to be disabled the control of the channel would be given back to the previous cue and so on until the first cue If no cue controls the channel the channel is put in standby mode if the stand by value has been defined otherwise it is left as it is the dimmers are usually set to zero while the remaining channels remain unaltered Activating a cue To activate a cue just press the corresponding playback key Following this operation other cues may activate in sequence depending on how the cue list is configured see Chap 3 Cue list paragraph Qlist Mode The master playback is internally set at 100 with the exception of playbacks which have controllers configured as playback masters in which case the slider becomes the master playback A cue can also be activated through the cue list window in Live mode see Chap 3 Cue list paragraph Live Mode IMPORTANTE the default configuration of the controller is Playback master which means that playbacks 1 to 12 have both an intensity slider and a flash key while playbacks from 13 to 24 only have a trigger key Switching off a playback To turn off a playback press the Release key and the playback key or alternatively press in quick succession the Release key and playback key before the led of the Release key switches off Change page When changing page all playbacks are assigned a cue list in the new page with the exception of
14. phase of the show The console provides the operator with up to 48 glists at the same time 24 if the expansions are not connected and up to a maximum of 12 manual cues according to how the controllers have been configured The result of the elaboration of the parameters is defined by the active cues and the controllers controllers here are to be intended as those which have been configured in manual cue The parameters which aren t involved by the active cues and the manual cues are set in Standby mode if the Standby mode is not defined then the output remains stable on the last value set by a cue or a manual cue IMPORTANT the editor and Hilite key always have priority on playbacks and controllers therefore with the exception of specific cases the transmission of a show occurs after having set the editor to zero double click on the Clear key Cue input When two or more cue lists compete for a channel the following criteria is applied depending on the Playback mode option setting in the General Options window o HTP channel the cue which has received the most recent trigger gains control of the channel regardless of the Playback mode settings e HTP channel and Playback mode LTP the criteria of the previous point is applied o HTP channel and Playback mode HTP is considered the highest value of all the cues contending the channel For each channel the console stores the organised list of cues which in time have passed the control
15. playbacks which aren t switched off active playbacks continue to control the cue list until they are disabled Only after the playbacks are disabled they will be assigned a new cue list Pag 26 RedMx 1 06 Controller input After having calculated the input of the active cues of the playbacks the console determines the input of the controllers in Manual cue mode the controller slider controls the cross fade between the manual cue and the cue playback processing result in practice when the slider is at zero the controller cannot give any input if the slider is at 100 the playback cues are ignored and the controller cue takes priority in intermediate cases to determine the final value the following criteria which also depends on how the manual cue was Saved is applied All channel fade the final value is the linear combination between the value of the controller and the result of the processing of the cues the closer the slider is to 100 the greater the influence is of the controller and the lower the Cue input and vice versa linear path e Snap Start channels which have path Linear follow the All channel fade criteria while to channels with path Snap_start or Snap_end the following criteria is applied if the slider is O the value of the playback cues appears the controller gives no input if the slider is above 0 the controller value appears Snap End the channels which have path Linear follow the All
16. pressing the Midi configuration button from Setup Menu First of all you have to define which cannel Midi messages directed to the console will be transmitted on you can set this value by moving the first wheel if you select All the console will receive all Midi messages regardless of the channel number which they are transmitted on Then you have to select the specific Midi message that will manage each functions In order to do this you have to move the second and third wheel for selecting respectively the message type Midi status byte and the starting value for the first Midi data byte Midi start value The first Midi data byte value represents the number of Cue list involved by the function this number is obtained by making the difference between the Midi data byte value and the Midi start value if the difference is null the current cue will be selected In this way a range of 25 values for each function will be reserved except for the Change page command that require only 24 values to address all the pages because the destination page number is calculated as the difference above mentioned plus 1 Pag 57 RedMx 1 06 The Playback level Effect soeed and Effect size commands need 3 bytes messages in order to be completely defined thus they cannot be managed by the Program change message that has 2 bytes only the first Midi data byte contains the Cue list number using the same convention already pointed out on previous paragra
17. shows previously saved on disk as for each show its data is saved in the fixture information It is often necessary to edit an existing fixture or it can be easier to create a new fixture basing on an existing one rather than starting from scratch From the context specific menu press Open a window will appear allowing to navigate the brands available on the internal disk or on the USB drive As in the Library manager a file can be selected and displayed or edited Pressing the Edit Dmx Ch button from the context specific menu allows to change the number of channels taken up by the fixture All other data concerning the fixture is directly available for display and editing in the Parameters Commands and Palettes windows After editing as needed the older fixture version on the disk can be overwritten by pressing the Save button in the context specific menu To save the fixture under a new name and or with another brand select Save As IMPORTANT fxr files recognisable from the character at the end of their name can be read but cannot be written and therefore cannot be edited It is possible though to open an fxr file and then save it as an fdf file Context specific menu The Context specific menu is the same in all of the three windows Lyp aici _ miina iii h v if calca aala alaa Context specific menu Buttons New Resets all programme data and prepares to create a new fixture definition file Open
18. status When the hilite is active the Hilite palette which usually opens the shutter and sets the dimmer at 100 is forced in the fixtures selected in the editor The hilite is typically used to create a cue without dimmer information in fact the operator can see the fixture s behaviour but such information is not inserted into the editor and therefore is not saved in the cue Locate Apply the Locate palette to the selected fixtures it defines a definitive status for all cue parameters typically dimmer 100 pan amp tilt 50 wheel color white etc Normally used before starting to program a series of cues Select Used to display the current playback or select a new playback By pressing the Se ect key the current playback led turns on if while the led is turned on you press the new playback key this playback becomes the current new playback You can also select a current new playback by pressing the Se ect key and the playback key in quick succession Selecting the current playback also occurs when pressing a playback key to transmit a cue the selected key is therefore used to change the current playback without transmitting any further cue Pressing the select key twice in quick succession selects the next playback Load Used to load a cue or a palette into the editor for any amendments The Load key loads the last cue or palette selected into the editor or if pressed simultaneously with the flash key of a controller it l
19. that will be controlled by the external Dmx device Since you can control the playbacks ranging from 1 to 24 the sum of First Playback To Map and Total playbacks to map fields has to be not above 25 Dmx Start Address This is the first of the n dmx channels used to control the playbacks intensity master with n equal to the Total playbacks to map value Go Release Dmx Start Address This is the first of the n dmx channels used to send Trigger and release commands to playbacks with n equal to the Total playbacks to map value Using the dmx channel that controls the playbacks intensity master is useful to address the cue storing If you move a slider after pressing the Store key the cue will be saved on the register controlled by the slider moved The Go Release channel works in the following way e Atrigger will be sent to the playback when the channel reach 100 e When the channel value goes down to 0 a release command is sent If you use aconsole having sliders and flash buttons you can set the sliders position at about 50 and use flash keys for to send triggers and move down the sliders to 0 to send Release commands IMPORTANT The dmx remote playbacks control has priority over built in controllers If the same playback is configurated in order to be controlled by a built in slider and by an external dmx device the Dmx device will take precedence and the built in slider will be disabled Pag 60 RedMx 1 06 Remote controller
20. wheel itself will be indicated Pag 10 RedMx 1 06 Console setup The setup of the console is very easy and consists of the following points Plug the power cable into the corresponding socket The console can be supplied with a voltage between 90 and 260 volts at a frequency of between 40 to 60 Hertz e Connect the dmx outputs to the fixtures or alternately the Artnet output to an Artnet Dmx converter in the case of the latter enable the Artnet output see Cap 5 Setup Artnet paragraph Connect any expansion units e Turn on the power switch located on the rear panel of the console IMPORTANT Each dmx output foresees two xlr connectors one 5 pin and one 3 pin that are internally connected in parallel Connect the fixtures to only one of these two connectors do not use both otherwise a mismatching of impedances may occur leading to a malfunction of the dmx Pag 11 RedMx 1 06 2 CREATE A NEW SHOW The creation of a new show requires a configuration phase in which the console is configured with all the settings and more importantly the number and type of fixtures involved in the show are set on the console All these operations are accessible from the Setup menu which in turn can easily be recalled by pressing the Menu key and selecting the Setup button located on the context specific menu Context specific menu Setup menu Adding fixtures to the library The console uses FDF files fixture de
21. window continue to show the same cue list until this cue list is released Pag 33 RedMx 1 06 Context specific menu The four cue list modes share the same context specific menu Cue list context specific menu Buttons Rename Qlist activates the digital keyboard in order to assign an new name to the cue list Copy Qlist duplicates the current cue list and assigns it to a new playback when open the virtual numeric keyboard digits the number of the page and of the destination playback separated by a dot Delete Qlist deletes the current cue list and all the cues contained in it Rename Cue opens the virtual number keyboard to edit the name of the selected cue Copy Cue duplicates and adds the selected cues to the end of the Qlist Delete Cue permanently deleted all selected cues after confirmation Move Cue opens the virtual number keyboard to assign a new ID to the selected cue IDs can be whole numbers or numbers with two decimals Change color opens the color picker to change the color of the buttons of the selected cues Pag 34 RedMx 1 06 4 CONTROLLER The controllers can be configured in three different ways using the Controller Configuration feature accessible from the Setup menu Playback master default configuration Group master e Manual cue The configuration of each controller is completely independent therefore it is possible to obtain any combination of modes Controller c
22. with 8 Add fixtures window Ls 40 ex fixtures of which only 6 are visible Pag 13 RedMx 1 06 Editor The console manages 24 pages of 24 playbacks each of which contains a cue list which in turn can be made up of in the simplest of cases one single cue or a maximum of 999 cues To create or edit a cue use the editor window or simply editor the editor allows you to control all attributes of all fixtures of the show and save their values as playback cues manual cues or palettes To edit a parameter of one or more fixtures first select them by pressing the buttons of the fixtures involved editor in fixture mode or by pressing the group buttons editor in group mode then with the buttons on the left select the family of attributes you wish to edit and finally using the wheels set the values To set the value of a previously set attribute to Empty click on the button of the wheel which controls it The trackball is always active on the pan and tilt of the selected fixtures Values can be conveniently set by using the palettes instead of the wheel and trackball see Palette paragraph In this case programming the cue is limited to selecting the fixtures single or in groups and to selecting the various palettes to use position colors gobo etc Each button of the fixtures and groups has two leds the left led shows the status of the fixture parameters Green all fixture group parameters are under the editor s control
23. 2 10 Midi Smpte and Dmx in sockets 11 Artnet output 6 universes 12 Dmx output universe 1 and 2 13 Power socket with switch Pag 8 RedMx 1 06 Edit keys Release used to interrupt a single playback Release playback key a single controller Release flash controller key all playbacks Release Page all controllers Release Bank all registers and all controllers double click on the key releases in quick succession Page used to select a new playback page the console manages 24 pages each of which contains 24 cue lists To select a new page simultaneously press the Page key and playback key corresponding to the new desired page or press these two keys in quick succession Press the Page key twice in quick succession to go to the next page Bank used to select a new controller bank the console manages 24 banks each of which contains up to 12 controllers depending on the configuration of the console To select a new bank press Bank the playback key corresponding to the new desired bank or press the two mentioned keys in quick succession Press the Bank key twice in quick succession to go to the next bank Clear Pressing once only erases the contents of the editor limited to the selected fixtures pressing twice in quick succession erases the entire content of the editor and unchecks all fixtures Clear all function Hilite Two state key alternatively activates and deactivates the hilite
24. REDMX 1 06 USER MANUAL LIGHTING REDMX General Warnings Check the power supply voltage is between 90 and 240 volts 50 60 Hz before connecting the device Class 1 Appliance It is compulsory to connect to a power supply with a solid grounding Do not open the appliance there are dangerous high voltage cables and live parts inside contact could cause an electric shock This appliance is not for household use only for professional use Keep out of reach of children and unauthorized users After removing the packaging ensure the appliance is intact if in any doubt do not use the appliance and contact an authorised assistance centre The packaging plastic bags polystyrene foam nails etc must not be left within reach of children as they are potential sources of danger Avoid flammable liquids water or metal objects from entering the appliance In the event of liquid spillage onto the appliance disconnect the power supply immediately Do not disassemble or modify the appliance Do not install this appliance outdoors directly exposed to rain or moisture Avoid using the appliance e In places subject to excessive moisture e In places subject to vibration or possible knocks e In places at temperatures above 45 or lower than 2 C Do not operate the appliance before it has reached its ambient temperature to avoid condensation Never attempt to repair the machine yourself Repairs carried out by inexperienced people m
25. Snap end When you save the console allows you to assign a reminder tag to the controller although you can enter up to 30 characters due to space constraints only the first 10 appear on the alphanumeric console display on the controller IMPORTANT The manual cue does not support effects potential effects in the editor will not be saved min nee nin maannimi ee in nen nen ign von nh i ie iene A a a oman aian mben PP a a R _ Dimmer Locate Save controller select mode Save controller insert tag Pag 36 RedMx 1 06 Editing a manual cue to load it in the editor press the key Load the flash of the controller Press and hold the Load key while pressing the flash key of the controller Once you have completed your changes simply press the Update key to Update the values of the manual cue Changing the current Bank To move to the next bank press the Bank key twice in quick succession To switch to a random bank press the Bank key in quick succession and the playback key of the desired new Bank or press bank key playback key The status bar of the console will reflect the change The bank change influences only the number One controllers of each bank the Fixed controllers always control the same cue regardless of the current bank When you change a bank you can no longer intervene on the active manual cues of the previous bank as the sliders and the controller keys control the cues of the new bank Activation
26. T If a group already exists with the same name the old group is overwritten To edit a group you proceed as just described paying attention when inserting the name of the group you want to edit Palettes display Palettes are predefined memories which speed up programming each fixture usually already has some predefined palettes in the fdf file but the user can create new personalised ones The preparation of pan tilt palettes is very useful in that once preparation of the palettes is complete the pointing of the fixtures is done simply by selecting the fixtures concerned and then clicking on the palette of the desired location IMPORTANT When programming the cues with the palette make sure the reference to the palette is saved rather than the values contained in it in this way when you edit a palette the changes made will be reflected on all its cues This photo is particularly useful to make positioning amendments on previously programmed shows The palettes are organised in the 6 parameter families Intensity Pan Tilt Colors Gobos Prism and Blade which can be selected by pressing the corresponding button The palette window displays all available palettes for the set of fixtures selected in the current family if no fixture is selected then all the palettes in the current family s show will be displayed The palette window shows a context specific menu which button is practically identical to the context specific menu of the fixtur
27. al to the user palette but these cannot be edited In this display mode the wheels and the Intensity Pan Tilt Colors Gobos Prism and Blade buttons maintain the same features as in the fixtures display mode Pag 21 RedMx 1 06 ee Sas e ___Gobo Rot 0 Gb Index 0 Program 0 Editor Rosco Palette display Context specific menu The context specific menu of the editor has the following buttons Free sets all the parameters of the selected fixtures to Empty Read copies all the current available output values into all the parameters of the selected fixtures This command ensures that all parameters of the selected fixtures are set to a not Empty value and therefore saving a cue stores the complete status of the fixtures and not just the directly assigned parameters IMPORTANT The Read command reads the status of the dmx and therefore loses the information of any paletted values or effects In this case the instant value of the parameter is considered Rename opens the virtual keyboard to edit the name of the selected fixture Change color opens the color picker window to select a new color to apply to the buttons of the selected fixtures Change ID opens the virtual number keyboard to edit the IDs of the selected fixtures The fixtures ID determines the order in which the fixtures are displayed in the editor the IDs can be whole numbers or numbers with two decimals If two or more fixtures are selected they will
28. alues Htp highest take precedence or Ltp Latest take precedence This value affects the computing criteria applied to the fixture s Htp channel usually for dimmers In Ltp mode the final value calculation uses the value of the cue activated most recently while in Htp mode the value used is the highest among all the cues affecting the channel Input mode Valid values Percentage or Raw This parameter only affects the way in which the values are displayed In percentage mode values are displayed on a per cent basis from 0 to 100 while in Raw mode values are numbers going from 0 to 255 for 8 bit channels or two values going from 0 to 255 for 16 bit channels Rgb Cmy palette set Set of all palettes that can be used in the editor Valid values Chris Gam Lee Rosco The editor provides the selected palette set to be used with all the fixtures having a CMY or RGB color mixing system Pag 42 RedMx 1 06 Fixture configuration This window allows to edit the configuration of all fixtures used in the current show All changes applied through this function only affect the current show leaving the fixture library unchanged All changes are automatically saved without any confirmation needed The first wheel allows too scroll down the list of features for the currently selected fixture The second wheel allows to select one of the show s fixtures To edit a value it is necessary to select it by pressing the corresponding but
29. ary to erase from the show all occurrences of that ixture entailing the loss of their programming and subsequently reload it Library manager Buttons Brand List Back to brand list display Pag 47 RedMx 1 06 Export brand Import brand This button which becomes Import brand when the USB drive is selected allows to copy all files contained in the current brand from the selected disk to the other disk The brand is copied without changing its name If the destination already contains a brand with the same name the programme will ask whether to replace it or to cancel the operation Export file Import brand This button which becomes Import file when the USB drive is selected allows to copy the current file from the selected disk to the other disk The backup file is copied from one disk to the other without changing its name If the destination already contains a backup with the same name the programme will ask whether to replace it or to cancel the operation Copy brand This button is used together with the Paste button to perform Copy and Paste operations It saves the current brand s path in the internal memory and makes it available for Paste operations The led indicator on the Paste button becomes green to signify that the Paste buffer now contains a path Copy file This button is used together with the Paste button to perform Copy and Paste operations It saves the current file s path in the
30. ay cause damage or serious malfunctioning Consult your nearest authorised Technical Service Centre When performing any operation observe all safety regulations in force in the country of use User Manual You can find a pdf version of the RedMx manual on the usb memory stick shipped with the console REO LIGHTING S R L Sede Legale Viale dei Mille 60 50131 Firenze Sede Operativa Via al Mare 143 47842 San Giovanni in Marignano RN tel 39 0541 1646317 fax 39 0541 16422094 www red lighting com Part IVA 06209690483 RedMx 1 06 TABLE OF CONTENTS lnutrod ctiON ess scsricsdcrrinisd rodot rirdi nda rh uurida ra D adde Eraka asiad CaN a a A E E E E AREEN Console Specifications OOS e TEE A P E E E Part 1 Quick start Guide 1 Overview of the console 1 1 Edit keys 1 2 Playback keys 1 3 Controllers 1 4 Grand Master e DBO 1 5 Pan tilt pointing 1 6 Encoder wheels 1 7 Console setup 2 Create a new SNOW sesssssesosossscsossossescsssessosssesossessoseeese 2 1 Adding fixtures to the library 2 2 Fixtures patch 2 3 Editor 2 4 Saving a cue 2 9 Editing a cue 2 6 Palette 24s 2 8 Store menu Part 2 User Manual We GCL AEE EE E EEP EE E AE E E E S EES D E E E ee E E E T Playing or transmitting a cue Editing an existing palette 1 1 Fixtures display 1 2 Groups display 1 3 Palettes display 1 3 1 Creating a new palette 13 2 1 4 Predefined palettes 1 5 Context specifi
31. be assigned progressive IDs Select Range The fixtures can be selected directly from the ID as well as by pressing the corresponding buttons By pressing the ID button a virtual number keyboard appears insert the maximum and minimum ID values corresponding to the fixtures to be selected separating them with a dot and confirm Context specific menu Pag 22 RedMx 1 06 Fan The fan feature assigns a sequence of values to the same attribute of the selected fixtures The sequence of values can follow the trend of a ramp or of a semicircle Once having selected all the fixtures involved in the editor press the Fan button and the corresponding window will appear fsa Linear Fan Amplitude t a Arc Fan Amplitude 0 Fan window Example of a Linear to Arc Fan The two series of buttons at the top allow you to select the parameter you wish to edit in the illustrated case we are working on the pan The distribution of the values assigned is influenced by 4 factors Fan type buttons e Linear selects a linear distribution of the values that is to say that the values assigned to the fixtures will be equally spaced e Arc assigns values according to an arc path Pivot buttons enables to select the pivot element of the group that is to say the element which remains fixed in position and around which the others move It is possible to select the first fixture eft the last fixture right or the central fixt
32. bnet mask must form a unique combination for each device Artnet configuration To configure Artnet simply press the Enable button and set the Sub Net and Universe values to the same ones assigned to the Artnet receiver These two values indicate the first DMX Universe of the console The other 5 DMX Universes are sent through the same Sub net and the following Universe Enable Enables disables Artnet output Sub Net Set a value between 0 and 15 accordingly to the receiver connected to the console Universe Set a value between O and 15 accordingly to the receiver connected to the console This value constitutes the first of the six DMX Universes transmitted by the console while the other 5 are sent through consecutive Universe values Certain Artnet systems use the naming Net and Universe whose validity range is respectively 0 127 and 0 255 In this case Net must be set to 0 while Universe must equal 16 x SubNet Universe The OK button saves all changes made and goes back to the Setup menu The Cancel button goes back to the Setup menu without saving any change Pag 45 RedMx 1 06 Backup restore The Backup Restore window allows to access a number of functions for the managing of copies and for restoring a show It is highly recommended to save a copy of the whole show also on an external USB drive every time a show is modified This operation while taking up only a few minutes can be of vital importance in case of emergenc
33. c Dmx device as a console expansion and control all playbacks and up to 288 manual cues through device sliders Two programs are provided in order to configure both features IMPORTANT Please connect the Dmx device or switch it on only when the console is up and running otherwise the console will not recognize the device Remote playbacks configuration The remote playback control by Dmx input you allows to manage the console playbacks through a generic device capable of transmitting Dmx data keeping the built in sliders free for other pourpose as Controller or group masters You can send Trigger and Release commands to console registers and control their intensity master using two dmx channels per playback The use of one dmx channel for sending triggers and Release commands is optional The Dmx n Playbacks Configuration window can be opened by pressing the homonymous button from Setup Menu On the status bar on the top right corner you can see the dmx input status if the dmx input is not connected or no dmx data are transmitted the Dmx In no signal message will be displayed otherwise three numbers will be showed that mean the receiver status 1 stands for receiver on the number of received data packets and the number of transmission errors The last two numbers are reset to zero every time the configuration window is opened You can change all the configuration values by moving the weels The configuration showed on the left
34. c menu 1 6 Fan 1 7 Effects 1 7 1 Editing an effect 1 8 Color picker 2 1 Cue input Zell Activating a cue NH ol on Pag 2 RedMx 1 06 Ola Switching off a playback 2133 Change page 2 2 Controller input pape Activating a manual cue 222 Switching off a controller Dies Change bank 2 3 Grand master and group masters De US TSE cocaine cana sas oaresasatnetteacnaten E E E EAE AARS 29 3 1 Qlist mode 3 2 Chase mode 3 3 Sequence mode 3 4 Live mode 3 5 Context specific menu Ws NCO WE e EE cred seus ey EEE ees Cera odes E E E 35 4 1 Controller configuration 4 1 1 Playback master mode 4 1 2 Group master mode 4 1 3 Manual cue mode 4 1 4 Saving a manual cue 4 1 5 Editing a manual cue 4 1 6 Changing the current Bank Pe a E E eaten A E E enol unesitaaas 38 5 1 Add fixtures 5 1 1 Patch window Dla Add fixtures window 5 2 General Options 5 9 Fixture configuration 5 4 Controller configuration 5 5 Pan tilt options 5 6 Artnet configuration 5 7 Backup restore 5 8 Library manager 5 9 Diagnostics 5 9 1 Dmxl output test I Dmx2 output test 5 9 3 Midi connection test 5 9 4 SMPTE Test 5 9 5 Expansion test l and 2 5 10 Fixture builder 5 10 1 5 10 2 5 10 3 5 10 4 5 10 5 Parameters window Command window Palette window Save in library Editing a fixture already included in the library Pag 3 RedMx 1 06 6 SMPTE Timi 6G Cis515 c cecccacccassescscatetnsiegesassesscensadheecasin
35. channel fade criteria while the channels with path Snap_start or Snap_end the following criteria is applied If the slider is lower than 100 the value of the playback cues appears the controller gives no input if the slider is equal to 100 the value of the controller appears A direct consequence of this algorithm is that if the manual cue contains a zero then by raising the controller slider to 100 the value of the channel is taken to zero The elaboration of the controllers is done according to the chronoplaybackical order of their activation therefore if one same channel is involved in two manual cues an intermediate result is calculated first by applying the calculation criteria while considering the oldest controller and then the intermediate result is elaborated again using the most recent controller Resultant Value Snap end path Cue Value Linear path Snap start path Manual cue Value 0 100 Slider position The drawing above is the graphical representation of 3 algorithms Activating a manual cue To activate a controller just move the slider away from zero if the slider of a controller is place on a value other than zero first take the slider to zero In any case pressing the flash key activates the controller which returns to its previous status when the key is released Switching off a controller A controller can be disabled by setting its slider at zero It is automatically disabled if
36. configuration This feature allows you to control by an external dmx device up to 288 manual cues that means you can have all the cues of all the console banks on your finger tips One or two channels can be used to control each manual cue one channel is used to control manual cue slider and the other one is used to manage the flash and release commands The Dmx n Controllers Configuration window can be opened by pressing the homonymous button from Setup Menu On the status bar on the top right corner you can see the dmx input status if the dmx input is not connected or no dmx data are transmitted the Dmx In no signal message will be displayed otherwise three numbers will be showed that mean the receiver status 1 stands for receiver on the number of received data packets and the number of transmission errors The last two numbers are reset to zero every time the configuration window is opened You can change all the configuration values by moving the weels The configuration showed on the left means that the first 48 channels of the external dmx device are used to control only PY Total controliers to map 48 the sliders of 48 manual cues Controller count Start Address Flash Relr Start Add Finestra Dmx In Controllers Configuration Window buttons and fields Dmx In Enable Dmx manual cue control global enable Dmx In Disable Dmx manual cue control global disable If this button is on the console will ignore a
37. ctors 2x Dmx Out e 23 pin xlr connectors Dmx duplication out 1rj45 connector 100Mbit Ethernet Artnet e I 5 pin xlr connector DMX In e 61 3 pin xlr connector SMPTE in e 3 DIN connectors Midi in Out Thru e 1 USB port for backup on external USB mass storage USB to light port Pag 6 RedMx 1 06 Glossary Attribute or Parameter every single function of a fixture which is controllable via Dmx or Artnet such as dimmers pan tilt color wheel gobo wheel etc Bank a group of 12 manual cues associated to as many controllers It is possible to store up to 288 manual cues arranged in 24 banks containing 12 manual cues each Button GUI element to press in order to activate the corresponding function It differs from the switch which is an actual key of the console Controller Controller an entity consisting of a slider and a freely configurable key playback master group master or manual cue Cue defines the status of an array of attributes It is often referred to as Scene or Memory Cue list an ordered set of cues also referred to as Qlist Cue list timing o timing a set of values which define the timing behaviour of the Qlist and of individual Cues Editor a programme that allows access to the parameters of the show s fixtures It is used to create and edit cues and palettes The editor has priority over all playback functions Empty status was not assigned to an attribu
38. d must be added to the show Fixture ID identification number of the fixtures to be added If two or more fixtures are being added the programme will assign them progressive ID numbers Dmx universe valid values for a DMX universe range from 1 to 6 both included Dmx start add starting DMX address If two or more fixtures are being added the programme will assign them progressive DMX addresses taking into account the number of channels used by each fixture and passing if necessary to the following universe IMPORTANT Universe 1 and 2 are also available on the console s xlr connectors while universe 3 4 and 5 are only available on Artnet Pag 41 RedMx 1 06 General options This window allows to edit the console s general options To edit a value select it by pressing one of the two corresponding buttons and use the fourth wheel The OK button saves all changes made and goes back to the Setup menu while the Cancel button goes back to the Setup menu without saving any change Percentage i Rosco Edit value General options window Default delay time Default value of the cue s delay time When a new cue is created it will be assigned this value Default fade in time Default value of the cue s fade in time When a new cue is created it will be assigned this value Stand by time Default value of the cue s stand by time When a new cue is created it will be assigned this value Playback mode Valid v
39. d then use the wheels IMPORTANT the Artnet connector uses a 100Mbit Ethernet connection It is necessary to verify that the device connected to the console supports such speed Pag 44 RedMx 1 06 Ethernet configuration Artnet configuration Static IP 192 168 0 52 Subnet 0 M Universe man ee pee Artnet configuration window Ethernet configuration DHCP Enable Disable This function can be enabled only if the console is connected to an Ethernet network with a DHCP server In this way the console will automatically acquire the IP number and the subnet mask from the DHCP server Static IP f the function DHCP Enable Disable is enabled this field will be ignored Otherwise it should be set accordingly to the other devices connected with the network While editing this field each wheel modifies one octet of the field Subnet Mask f the function DHCP Enable Disable is enabled this field will be ignored Otherwise it should be set in accordance with the other devices connected with the network in general it is set to 255 0 0 0 or 255 255 255 0 While editing this field each wheel modifies one octet of the field The IP number and the subnet mask are each composed of 4 octets ranging from O to 255 separated by a full stop A simplified rule to assign IP numbers to a network without a DHCP server is as follow all devices must have the same octets for the subnet mask 255 while the octets corresponding to the Os in the su
40. e Expansion test 1 and 2 Pressing the buttons Exp 1 and Exp 2 allows to verify the correct functioning of these two expansions When pressing the button Exp 1 the diagnostic programme receives data from the selected expansion instead of the internal card of the controllers playbacks When expansion commands are activated the graphical representation on the screen will respond immediately Pressing the button Exp 2 performs the same test on Expansion 2 Press the Cntrl button to go back to the test of the console s internal card Fixture builder For each fixture included in a show the console uses a fixture definition file called fdf containing the information necessary to hide from the user s view all technical details The information necessary for creating an fdf file is number of DMX channels taken up by the fixture e list of fixture s features and corresponding internal patch any information on commands such as reset lamp on etc e information for inserting predefined palettes value ranges for color wheels or gobos macro channels etc It is not mandatory to insert a palette the user is free to decide whether to use them or not Of course a fixture with a good palette set is easier to use IMPORTANT Each fixture is subject to the following restrictions Maximum number of parameters 128 Maximum number of commands 16 Maximum number of library palettes 64 Moreover the total number of features included
41. ecauses 55 6 1 Creating a list of events 6 2 Executing the list of events 6 3 Smpte connection 1 MTD inier ACG po cotucu eceeihaatiedenchesudinerasdeidesgdessientestraeddadesnunes 57 7 1 MIDI configuration D CET a soe ise teen seo enee tenet E T 59 8 1 Remote playbacks configuration 8 1 Remote controllers configuration fe Og E ET ee eee 63 9 1 Console connection 9 2 How the expansion works 9 2 1 Page organisation O 2 2 Sliders and keys Pag 4 RedMx 1 06 Introduction This manual is divided into two parts the Quick Start Guide which gives a general overview of the console and enables the operator to be immediately operational using the basic functions The second part is the actual user manual where many of the concepts seen in the first part are examined in greater detail It is recommended that you first read the Quick Start Guide in order to have a global overview of the console s features and settings and to be able to contextualize the information in the second part more accurately General Warnings Class 1 Appliance It is compulsory to connect to a power supply with a solid grounding Do not open the appliance there are dangerous high voltage cables and live parts inside contact could cause an electric shock This appliance is not for household use only for professional use Keep out of reach of children and unauthorized users After removing the packaging ensure the appliance is intact if in any
42. ect button otherwise simply trigger a glist to make the cue list current Qlist Chase Sequence Live cue list mode selection buttons EDITOR recalls the editor window Link Next cue if activated upon completion of the Fade in it sends an automatic trigger to the following cue Wheels When one or more cues are selected the wheels allow you to respectively set Delay Fade in Wait e Fade out times if there are no cues selected the wheels respectively become Master Size Master Speed Master Intensity and Scroll wheel IMPORTANT during playback it could be useful to use the wheels to regulate in real time the amplitude Master Size and the speed master Speed of the effects of the cue or the intensity of the dimmer Master Intensity These three values are not saved on the disk and every time the cue list is activated they return to their default values Chase mode In a cue list configured in Chase mode all cues are assigned a common timing and timings at single cue level are disregarded If the Auto mode is active upon every Fade in completion a trigger is automatically sent to the following cue on the other hand in Manual mode to activate the following cue a clear trigger is necessary One of four options can be selected for the execution order of the cues e Forward the cues are executed in the natural order that is to say from the first to the last and then starting again from the first e Reverse the cues are e
43. er through DMD and Artnet outputs This programme allows to verify the good functioning of all the consoles buttons sliders inputs and outputs The diagnostic window displays through graphical representation all commands trackballs wheels sliders and buttons When any command is activated the graphical representation on the screen immediately responds allowing to check whether all command work properly The status bar on top shows in real time the data transfer between the console s internal cards Data packets are displayed in the following order transferred packets received packets packets containing errors For a correct functioning the number of transferred packets should be almost identical to that of received packets and the number of errors should be lower than 0 1 1 per mil of transferred packets Master Tx Rx err 515 513 Editor keys Grand master and DBO Controllers and playbacks keys Trackball and Pan lock Fine and Tilt Lock keys Encoder weels Diagnostic window Dmx1 output test Connect with a male to female DMX cable the Dmx1 output with the Dmx in input and press the Dmx1 button the console will transfer a certain number of data packets through the Dmx1 port and compare them with the data received from the Dmx in input If the two sets of data match the test is considered as a pass if they do not match the test is considered as a fail Obviously this test also verifies the correct functioning
44. es between Fixture display and Group display e Palette recalls the Palette display Cmy Recalls the default palette window which can be used on all fixtures with RGB or CMY color mixing systems e Effects Recalls the Effects window o Fan Recalls the Fan window e Unselect All Deselects all selected fixtures 3 parameter selection buttons Pressing one of these buttons the 4 parameters of the corresponding family limited to selected fixtures are displayed on the wheels and can be edited If the selected family has more than 4 parameters press the button again to scroll through Pag 18 RedMx 1 06 them all 4 at a time 4 wheel buttons Each wheel is associated with the parameter displayed on the corresponding button relating to all selected fixtures with the wheel it is possible to contemporaneously edit the fixture values Pressing the wheel button resets all the attributes associated with it to Empty There are three reporting and status features on each button The tag 9 the representation of the anaplayback value 10 and the status of the led channels 11 5 slider fixture buttons scroll bar The scroll bar is also provided with a Bookmark button This button is used to move quickly to an exact location on the list Press and hold the Bookmark button for more than 0 5 seconds in doing so the current position is saved and the led on the button is lit each time you press the Bookmark button the li
45. es window however the Select Range does not appear Pag 20 RedMx 1 06 Creating a new palette After having set the parameters of the fixtures to the desired value you can save their status in a new palette by recalling the Store menu which is done by clicking the Store key select the type of palette you wish to save buttons 1 and then insert the name of the new palette you wish to create by using the virtual keyboard IMPORTANT when creating a new palette only the parameters which belong to the same type of the created palette are saved Palette display editor mode Store menu Editing an existing palette To edit an existing palette do as follows e Select the palette by pressing the corresponding button e Press the Load key the Load key loads the last palette used into the editor e by using the features of the editor carry out the necessary changes o finally press the Update key which will substitute the old palette with the new values IMPORTANT if you edit a palette all the cues which referred to this palette will consequently be modified Predefined palettes The console has four sets of predefined palettes Chris Gam Lee and Rosco with RGB and CMY color mixing system The window of the predefined palettes to display press the CMY button displays the palettes of the current set which can be set in the General Options menu located in the Setup Menu The predefined palettes can be identic
46. ey are Pag 16 RedMx 1 06 Store menu The Store menu which is activated by pressing the Store key enables you to save different types of objects Store palette Store cue buttons _ __ buttons Dimmer Locate Menu store Buttons Intensity Pan Tilt Color Gobo Prism and Blade save the editor content limited to the selected type of parameters in a new corresponding palette Cue saves the editor content adding it as new cue into the current playback Snapshot saves the status of the channels controlled by the Editor Playbacks and Controllers by adding it like a new cue to the current playback Controllers saves the status of the channels controlled by the Controllers adding it like a new cue to the current playback Group Creates a new group containing the selected fixtures Pag 17 RedMx 1 06 PART 2 USER MANUAL 1 Editor The editor is the programme which enables you to set and edit the values of all parameters of the fixtures and to save their status as a cue or palette The editor has various windows and displays when switched on the console shows the editor in display fixtures mode Fixtures display scroller Locate Fixture display editor mode Window contents 1 status bar From left to right Current playback Current page and Current Bank 2 command buttons Each of these buttons carries out a specific command or opens a different window Fixt Grp Switch
47. finition files or Pilot 3000 FXR files as it is fully compatible with the latter To import fdf or fxr files into the console use a normal USB drive on the USB create an FDFLIB folder which will contain the folders of the brands which contain fdf files then place the USB in the USB port of the console and using the Library manager Setup menu import copy single files or entire folders Do you want to copy the current file on internal disk Importing a fixture into the console library For example importing a RedLighting Ls 40 Ex fxr file Supposing the USB memory is recognised as a disk G of our PC Pag 12 RedMx 1 06 1 We create the G FDFLIB folder and then a G FDFLIB REDLIGHTING folder we then copy the Ls 40 ex fxr file into the G FDFLIB REDLIGHTING we have just created 2 We place the USB drive into the USB port of the console press the Menu key to recall the Setup menu and select Library manager er From the Library manager we press the Menu key and then USB disk all the folders available in FDFLIB will be displayed by pressing the RedLighting button all existing files in the FDFLIB REDLIGHTING folder will be displayed 4 We select our fixture by pressing the RedLighting button and then again on the Ls 40 Ex fxr button the led of the Ls 40 ex button will turn red to confirm the selection 5 We press the Import button and confirm In this way by going back to the internal disk Internal disk button of
48. for example we had set Fade 40 and Speed 15 bpm in Auto mode we would have a total cue time of 60 15 4 seconds with a Fade in of 4 40 100 1 6 seconds therefore the cues would take 1 6 seconds to perform the fade in and would be activated every 4 seconds In any case in Manual mode we would have a Fade in time of 1 6 seconds but activation of the cues would remain under the control of the operator IMPORTANT during playback it could be useful to use the wheels to regulate in the real time the amplitude Master Size and speed master Speed of the cues or the intensity of the dimmer Master Intensity These three values are not saved on the disk and every time the cue list is activated they return to their default values Pag 31 RedMx 1 06 Sequence mode In Sequence mode the cues are automatically activated upon fade in completion of the previous cue the order of activation is the natural one that is to say from the first cue to the last and then starting again from the first IMPORTANT when the first cue of the sequence is activated for the first time the Delay time is disregarded that is to sa that when a trigger is sent to a sequence this is done disregarding the Delay of the first cue which will be considered normally in the following automatic activations Wait and Fade out times cannot be inserted in this mode and are considered identical to the Delay and Fade in times I Cue list mode selection buttons 2
49. he first cue on the cue list contained in the playback or it activates the following cue if the cue list had already been activated Go function It can be used together with the Release e Select keys respectively to release and select the cue list Pag 64 RedMx 1 06 The selection pause key located in the first row of keys at the bottom has two different task depending on whether the cue list is on or off If the cue list is off it is used to select the current playback without having to use the Select button When the cue list is active it transforms into a play pause key when pressed once it freezes any on going effects or fade ins and fade outs when pressed a second time it unfreezes the evolution of the cue which starts again from where it had been suspended Pag 65 p E Techni luv www techni lux com
50. he fixtures belonging to the group itself IMPORTANT if a fixture belongs to more groups the lowest master is considered Pag 28 RedMx 1 06 3 CUE LIST A cue list or glist is an organised group of cues Each cue contains information on the status of one or more parameters belonging to one or more fixtures and the information relating to its trend in time Each cue list can be configured according to four different modes Qlist Chase Sequence or Live Depending on the mode the way in which the cues are triggered and the calculation of their timing changes Qlist mode The evolution of a cue in time is determined by the trigger and evolves according to the times inserted Delay Fade in Wait e Fade out Cues are triggered either by pressing the playback key which controls it or due to a predefined event on one of the input ports o Delay time between the trigger and actual activation of the cue e Fade in fade in time of the cue Wait time between the trigger and fade out e Fade out fade out time IMPORTANT Delay Fade in and Wait Faidtout times define two time lines and are not in sequence Time evolution of a cue which has received a trigger At the Delay stage the LTP e HTP attributes set at values other than zero start to move towards the final value will reach it in a time equal to the Fade in At the Wait stage the LTP e HTP set at zero or Empty start to move towards zero and will reach it in a time
51. hen the Play button is active each event is compared against the smpte time and potentially activated Unselect all deselects all events valid only in Edit mode Sort tidies the list of events based on a growing smpte times valid only in Edit mode Delete deletes after confirmation all selected events valid only in Edit mode New from the context specific Menu Deletes the current list and prepares for the creation of a new list Save as from the context specific Menu saves duplicates the current list under a new name Open from the context specific Menu opens the browser to load a list which had previously been saved on the disk IMPORTANT before putting a list in the play status make sure it is tidy otherwise press the Sort button if the list is not tidy the correct execution of events is not quaranteed Play status is maintained even after exiting the Smpte window Pag 55 RedMx 1 06 Creating a list of events When the Smpte window is in Record mode any event generated by the console for example sending a trigger to a playback is added to the queue of Smpte events in a new line If the Smpte source is not connected the new event has 0 0 0 0 activation time the Smpte source is connected the activation time is read by the Smpte timecode The events which can be included on the list are Cue trigger Cue list release e Release of all Qlists e Change page Usually the Record stage is follo
52. her without changing its name If the destination already contains a backup with the same name the programme will ask whether to replace it or to cancel the operation Internal disk e USB disk These two buttons allow to select respectively the internal disk and the USB drive The red led indicator on the button corresponding to the selected disk will turn on Exit The Exit button goes back to the Setup menu Library manager The Exit button goes back to the Setup menu The fixture library is composed of fdf files fixture definition file and fxr files which the console uses to avoid displaying all technical details of the fixtures included in the show Fdf files are organised in brands or folders which are in turn located inside the FDFLIB folder This programme allows to manage this structure through the copy delete duplicate functions both on a single file basis and on a brand basis Library manager displays all brands available on the internal disk To view the fixtures included in a brand just push the corresponding button Pushing the Brand button goes back to the brand list To exit the programme use the context specific menu IMPORTANTE substituting or deleting a library file does not affect in any way the current show nor the shows previousl created When a fixture is loaded in a show the console automatically creates a copy of the fdf file and saves it in the show s data To apply the changes made to a library fixture it is necess
53. his measure through a specific message Delete After asking to confirm this command deletes the selected features from the show Deletion is final it cannot be undone and eliminates all settings for the deleted fixtures This command however does not modify in any way the fixture library files IMPORTANTE if the fixture definition file for the show is incorrect it is necessary to remedy the mistake through the Fixture configuration programme Editing the corresponding fdf library file does not have any effect In order to appl changes to a library file it is necessary to erase from the show all corresponding fixtures thereby losing their rogramming including palettes and subsequently re insert them Pag 40 RedMx 1 06 Add fixtures window Pressing one of the fixtures buttons in the navigation section of the Patch window displays the Add fixture window Generic fixtures 3 pm Fixture Name Ls 40 ex Fixtures to add Dmx universe i Fixture ID Dmx start add i ee PVA Fixture to add Dmx Universe Startaddress Add Fixtures window Buttons Edit name opens the digital keyboard allowing to edit the name to be used for a fixture during the show Add fixture this button closes and finalizes the addition of a fixture to the show Cancel this button cancels the operation closes the Add Fixture window and goes back to the Patch window Wheels Fixture to add how many fixtures of the selected kin
54. i messages The playback functions controllable by Midi protocol are Cue list activation Cue list release Cue List flash activation Cue List flash deactivation Cue list intensity submaster setting Cue list effect speed master setting Cue list effect size master setting Page change CON DU BWHN FR Before exploring how the Midi configuration window works we will talk a little bit about Midi messages structure a Midi message has 2 or 3 bytes depending on message type the first byte called Midi status byte contains both the message type Note On Note Off and the channel number the following bytes called Midi data bytes have different names and meanings depending on message type and their value can range from 0 to 127 In order to control the console playback functions it is necessary to assign a Midi status byte to each of them the available messages for console playback control are e Note Off 3 bytes followed by Note number and velcity e Note On 3 bytes followed by Note number and velcity e Control Change 3 bytes followed by Control number and Nnew value e Program Change 2 bytes followed by New program NOTE by convention it is assumed that a Note On message with zero velocity is interpreted as Note Off Due to its features the Program Change message cannot be used to control the master setting functions functions 5 6 and 7 MIDI Configuration The Midi configuration window can be opened by
55. ile executing particularly complex shows Diagnostic Launches the diagnostic programme allowing to verify the good functioning of all hardware and of the whole system IMPORTANT this function interrupts the console s normal functioning suspending DMX and Artnet transmission Software upgrade This function updates the console to a newer software version Once the software update is completed the console must be restarted Where specific instructions are not given with the update insert the USB drive containing the update file and confirm After about ten seconds an update complete message will appear together with a reminder to restart the console Back to editor Exits Setup menu and opens the editor Add fixtures The console can manage a maximum of 3072 channels 6 DMX Universes and in any case no more than 1024 fixtures IMPORTANT Universe 1 and 2 are also available on the console s xlr connectors while universe 3 4 and 5 are only available on Artnet Pag 39 RedMx 1 06 Patch window The Address Patch button in the Setup menu opens the Patch window which is divided in two main parts one to navigate the fixture library and the other to view the list of fixtures included in a show EEGs 1 Fixture library browsing area dgani ew qT 3 2 2 Elenco delle fixture inserite nello show 3 DMX universe valid values are from 1 to 6 4 DMX start address Brand scroll Patch Scroll Patch wi
56. ith the Release Select Page and Bank keys see Edit Keys section Controllers The controllers can be individually configured in three different ways Playback master manual cue or group master Configuration of the controllers is carried out by means of the Controller configuration window retrievable from the Setup menu see Chap 4 Controllers the default value after a Clear show is Playback master Grand Master e DBO The grand master slider only regulates the level of the console HTP channels usually the channels that regulate the brightness of the fixtures Pressing the DBO key Dead Blackout will immediately force all HTP channel levels to zero and these will remain at zero as long as the key is pressed Pan tilt pointing For all pan and tilt pointing the console features a 38 mm trackball and three keys Pan lock Tilt lock and Fine The Pan lock and Tilt lock keys are two state keys which allow to respectively lock the pan and tilt movements while the Fine key is a three state key that when repeatedly pressed activates three different types of trackball sensitivity 8 12 and 16 bits The Fine key affects the behavior of the encoder wheels too Encoder wheels Encoder wheels are used differently depending on which windows are active but their main use is to change values or scroll to lists of names and or objects On a case by case basis on the graphic screen in correspondence of each wheel the function completed by the
57. ll the rest of the configuration and the manual cue control by dmx input is inhibited Flash Rel Enable Flash and Release receive command enable Two dmx channels for each dmx controlled manual cue are used if this button is selected Flash Rel Disable Flash and Release receive command disable Only the slider of manual cue is controlled if this button is selected Pag 61 RedMx 1 06 OK If the new configuration is error free it will be activated and saved on the disk and the configuration window will be closed otherwise an error message will appear Cancel It aborts all the changes made and goes back to the Setup Menu Total controllers to map This value is the total number of manual cues that will be controlled by the external Dmx device You can control up to 288 manual cues that means all the manual cues of all the console banks Dmx Start Address This is the first of the n dmx channels used to control the manual cue sliders with n equal to the Total Controllers to map value Flash Release Dmx Start Address This is the first of the n dmx channels used to flash and send release commands to controllers with n equal to the Total Controller s to map value Using the dmx channel that controls the manual cue sliders is useful to address the manual cue storing if you move a slider after pressing the Store key the scene will be saved on the manual cue controlled by the slider moved The Flash Release channel works in the fol
58. lly involved offers a compact visualisation of all relevant palette data To eliminate a parameter of the set of active parameters set it to e View All Parameters View all parameters in the palette body The display mode allow you to add parameters to the set of parameters used by setting them to a value other than Save in library From the context specific menu press the Save button If the fixture had already been saved it will be simply overwritten If it is being saved for the first time a window will open automatically as in the Library manager to allow navigating the brands available on the internal disk or on the USB drive When a brand is selected the digital keyboards will appear asking to type in a name for the fixture The programme always verifies the data inserted and if an inconsistency is identified it will display a diagnostic message The message can contain two kinds of notification a warning or an error Warning notifications signal an unusual yet valid situation e g not all DMX channels are occupied by a parameter The user can decide whether to cancel the command and properly edit the fixture or to go on saving Error warnings signify invalid situations and must be corrected before saving e g two features sharing the same internal patch Pag 53 RedMx 1 06 Editing a fixture already included in the library IMPORTANT editing a library file does not affect in any way the current show nor the
59. lowing way e Reaching 100 is equivalent to bring the manual cue slider at 100 e When the channel value goes down to 0 a release command is sent IMPORTANT if you enable the manual cues remote control by dmx all the controllers configurated as manual cues are changed in playbacks masters and the control of all manual cues is moved to the extern dmx device Pag 62 RedMx 1 06 9 EXPANSION ety empty empty empty emety empty Front panel l Playback status Flash keys Intensity Master Trigger Keys Select Pause Keys oe eS E Power socket with switch Pag 63 RedMx 1 06 Connection to the console The expansion is connected to the console via the single cable provided 6 pin phone cable with a pin to pin connection and does not require a power cable Connecting is very easy e Make sure that the console is switched off Connect the connection cable between the Exp 1 or Exp 2 switch and the socket on the rear panel e Switch on the console It is possible to connect up to maximum two expansions per console IMPORTANT connect the expansion to the console exclusively using the cable provided The use of unsuitable cables may cause permanent damage to the expansion How the expansion works Each expansion gives the operator an extra 12 playbacks Each playback is made up of a cursor potentiometer and three keys It is a fully configured system with two expansions capable of transmitting 48 cue lists co
60. n of playbacks which have controllers configured as playback masters in which case the slider becomes the intensity master When two cues belonging to two different playbacks clash on a same channel the console applies the following criteria if the channel is LTP the LTP criteria is always applied the most recently activated cue has priority e if the channel is HTP the LTP or HTP criteria is applied the highest values appears as specified in the Playback mode field of the General options page Setup Menu You can productively choose the Live window to transmit cues without a predefined order ATTENTION The editor has priority over the playbacks therefore ensure it is not checking any fixtures prior to transmitting a cue To reset the editor press the Clear key twice in quick succession ee See ae ae Pan Chorus Tilt Chorus PT Speed 0 Gobo Rot 0 ___Gb Index 0 Program 0 Pan tilt palette window with highlighted Predefined Rosco palettes in 1 the selection buttons of the palette family To turn off a playback press the Release key and the playback key in quick succession before the led of the Release key switches off or alternatively press and hold the Release key while pressing the playback key This action puts all projectors involved by the cue to Stand By mode defined by the Stand by values in the fixture configuration window the dimmer is typically reset to 0 while the remaining channels stay set the way th
61. ndividually configurable as playback master group master manual cue e 24 keys for direct access to the playback registers e 4 wheel encoder to control the features during programming and to control effects during playback e 38mm Trackball for immediate and precise control of PAN and TILT movements e Grand Master Slider DBO Button FEATURES e Powerful graphical interface able to easily manage the scheduling and playback of up to 576 Cue lists organized into 24 pages from 24 cue lists each having a maximum of 999 Cues e 3072 Channels on 6 independent universal DM Xs for the management of dimmer and or motorized projectors of which 2 simultaneously available on 5 pin xlr and 3 pin xlr connectors e Simultaneous playback of up to 48 cue lists e Advanced effects generator Updatable personalities library e 6 families of programmable palettes for a quick and flexible programming of the intelligent projectors e 6 Pre programmed Chris Gam Lee Rosco palettes for use on all machines with RGB or CMY color mixing e Cues max 999 for each playback register e A maximum number of 9999 storable cues per show e flexible led light e Internal interchangeable universal 85 265 volt power supply e Appliance equipped with a 454 Mhz processor with 128 MB RAM e 6Internal 4 GB SD memory card to store libraries and user data CONNECTIONS All console inputs and outputs except for the usb ports are galvanically isolated e 25 pin xlr conne
62. ndow Buttons Brand List Back to the Brand list Exit Back to Setup menu Pressing one of the brands buttons directly display the list of fixtures belonging to the corresponding brand Pressing one of the fixtures buttons directly displays the Add Fixture window allowing to add a fixture to the show The context specific menu in the Patch window contains the following buttons Disable fixture Disable the selected fixtures Disabled fixtures do not take up any DMX channel and are not taken into account in any computation they are easily recognisable as their address is displayed in grey font and preceded by an asterisk Enable fixture Opposite to the disable fixture button it re enables the selected fixtures If this command creates an overlapping the programme automatically disables some of the fixtures in order to restore a valid configuration and notifies the user of this measure through a specific message Change Address Displays the digital numeric keyboard to allow editing the universe and the DMX address of the selected fixtures type in the value for the universe and for the address separated by a full stop If two or more fixtures are selected the programme will assign them consecutive DMX addresses passing to the following universe if necessary If the newly assigned address creates an overlapping the programme automatically disables some of the fixtures in order to restore a valid configuration and notifies the user of t
63. ng algorithms for Htp and Ltp channels sometimes generating results apparently unaccountable IMPORTANT please remember to carefully check the Standby Hilite and Locate values For obvious reasons default values are not always appropriate Gobo Spin Gobo Rot cabo Index Effect Macro Prism Prism Rot Blade Blade Rot Insert number of dmx channels Parameters selection Parameter Htp Ltp Type Patch H Patch L Path Standby Hilite Locate Hip Ltp Type Pateh High Patch Low Parameters window Pag 51 RedMx 1 06 Commands window Once the parameters have been inserted by pressing the Commands button it possible to insert the fixture commands such as Lamp on Lamp off Motor reset etc Pressing the New Cmd button allows to add a new command to the list which at the beginning will be empty of course The command s values are set using the wheels Internal patch DMX address for the output of the command value Dmx value value to output Time time in seconds for which the value has to remain constant during output More complex commands can be added by inserting more rows of values through the Add row button Internal patch Dmx Value Time i mi E m un Comando selezionato Lista comandi Internal Patch Time seconds Commands window The window includes several buttons for editing data e New Cmd Allows to add a new command e Add Row Allows to add a ne
64. ntemporaneously 24 are controlled by the console playbacks and 24 are controlled by the playbacks of the two expansions Page organisation The connection of the expansions does not modify the amplitude of the pages of the console which continue to contain 24 cue lists each the presence of expansions simply allows you to control two pages at the same time the current page thanks to the console playbacks and the following page through the expansions If only one expansion were connected this would allow you to control the first 6 cue lists of the following page To use the expansions as conveniently as possible we recommend always setting the current page on an even page this way even pages are on console playbacks and odd pages are on expansions The advantage of this type of organisation consists in being able to easily access all cue lists of a show designed and prepared for the use of expansions even when these are not present Sliders and keys Each expansion controls 12 playbacks each of which has 3 keys and a slider The slider is the cue list s master of intensity that is to say it reduces all HTP channels controlled by the cue list The key above the slider performs the playback s flash function when you press it it instantly sets the slider value at 100 and keeps it that way for as long as it is pressed The trigger key located right under the slider is the equivalent of the console s playback key when pressed it activates t
65. ntent of the cue and recreates the groups of fixtures which have the same effect To open simply press the Selector button when you are in the effects generator window The column button on the left highlights how many groups of fixtures contain effect for each family of attributes for example in the picture there is a cue which contains 4 groups of fixtures having as many effects two Intensity effects and two Pan Tilt effects Press the buttons on the left to scroll and select in sequence the groups of fixtures having the same effect Once having identified the group which contains the effect to be edited press OK to go back to the effects generator window and edit OS gt ae j dE First of two Intensity effects is selected Two different pan amp tilt effects available 0 0 ee A l540ex Prism 7 l 20 070 amannan o B40 Selector window Color picker The color picker window is used to change the color of the buttons relating to different types of objects Fixtures palettes cues Colors can be selected directly from the bitmap 1 or using the first three wheels the RGB CMY HSB button selects the input mode scrolling through the three available colors Red Green Blue Cyan Magenta Yellow and Hue Saturation Brightness Hue 64 aon 237 Bri SS 242 Color picker Pag 25 RedMx 1 06 2 PLAYBACK Playback is the moment when the programming activity of the show is finalised or the execution
66. oads the controller cue into the editor only if the controller is configured in manual cue Pag 9 RedMx 1 06 Store Activates the Store menu When the store menu is active it is possible to save a palette yellow buttons a cue brown buttons or save the currently selected fixtures as a new group If a controller is configured in manual cue by simultaneously pressing the Store key and its flash key the contents in the editor are saved in the cue associated with the controller itself Pressing the Store key twice in quick succession saves the contents of the editor as a new cue in the current playback Update Updates and saves the last cue or palettes loaded into the editor During loading the console keeps track of the amount loaded into the editor the Update key overwrites the original cue or palette with the current contents of the editor Edit Qlist Key that alternately recalls the windows of the editor and cue lists Menu Activates a pop up menu that allows access to auxiliary functions of a particular window In each window for reasons of space or opportunity less frequently used functions are placed in the context specific menu Playback keys When you press a playback key it activates the first cue on the cue list contained in the playback or activates the next cue if the cue list was already active Go function this last playback also becomes the current registry playback Can be used in conjunction w
67. of the Dmx in input Dmx2 output test Connect with a male to female DMX cable the Dmx1 output with the Dmx in input and press the Dmx2 button the console will transfer a certain number of data packets through the Dmx port and compare them with the data received from the Dmx in input If the two sets of data match the test is considered as a pass if they do not match the test is considered as a fail Obviously this test also verifies the correct functioning of the Dmx in input The two DMX connectors of each output are internally connected but in order to make sure that the wiring works properly it is advised to verify each port twice using first one connector and then the other Midi connection test Pag 49 RedMx 1 06 Connect with a midi cable the midi in input to the midi out output and press the Midi button the console will transfer a certain number of data packets through the midi out port and compare them with the data received from the midi in input If the two sets of data match the test is considered as a pass if they do not match the test is considered as a fail This test verifies at the same time all Midi in and Midi out ports No test is available for the Midi thru port Smpte test To test the Smpte port simply connect a Smpte generator to the corresponding input on the console The diagnostic status bar top right scrolls the Smpte frames in real time allowing to verify the correct reception of the Smpte timecod
68. onfiguration Press the Controller configuration button from the Setup Menu to access the window Controllers 1 1 mee E One for each bank TET aa panan pan por Hil rns noiae cow ne Scroll list Change value Controller configuration window Buttons OK saves the changes and returns to the Setup menu Cancel returns to the Setup menu without saving any changes Clear all cues deletes after confirmation all controller cues of all banks Playback master mode In this mode playback master the slider and the controller key become master and flash of the corresponding playback i e controller 1 becomes master and flash of playback 1 controller 2 of playback 2 and so on until controller 12 playbacks 13 to 24 cannot have a master Group master mode In Group master mode group master the slider becomes the master of intensity of all fixtures belonging to the group allocated to the controller IMPORTANT If a fixture belongs to two or more distinct groups that are assigned to as many controllers the fixture will be E Pag 35 RedMx 1 06 lowered according to the lowest value of the sliders Manual cue mode In this mode it is possible to associate a single cue to the controller Fixed mode or up to 24 different cues organized in as many banks mode One for each bank In Manual cue mode the slider controls the cross fade between the controller s cue and the playback proce
69. other controllers or the editor take away channel control To reactivate the controller set the slider at zero and then raise it to the desired value Pag 27 RedMx 1 06 Change Bank When changing bank all controllers configured in manual cue mode One for each bank will control the manual cue it has been assigned in the new bank If a manual cue is active it will stay active and continue to give its contribution even by changing bank it is important to note that in such a situation there is no control on the console capable of controlling the above mentioned manual except Release All to regain control it is necessary to change the bank once again and return to the previous bank and then move the controller slider until crossing the original value of the manual cue A controller configured in Manual cue Fixed mode is not influenced by the bank change and keeps controlling the same manual cue Grand Master and group masters You can intervene in real time on the result of the cue and manual cue elaboration using the Grand Master and DBO key and group masters The Grand Master only influences the HTP channels typically the fixtures dimmer proportionally reducing their value The controllers can be configured as group masters see Controllers paragraph in this case we could have up to 12 intensity masters corresponding to as many groups A group master just like a Grand Master proportionally reduces all HTP channels of t
70. ph and the second Midi data byte contains the master value information coded in two different way depending on the command e Playback level the level is expressed as percentage if the value is above 100 will be interpreted as 100 e Effect size and Effect speed the level is expressed in step of 4 percentage points so that the value 25 stands for 100 the value 127 that is the maximun value allowed for midi data bytes stands for 508 Midi status byte Midi start value EE aeons A 6 arenes I Note On 0 CO Note On 30 F 2 E Note On 60 C5 Note On 90 F 7 Ctl Change 0 a Ctl Change 30 Ctl Change 60 Pgm Change 0 MidiCh All Status Byte Midi Message Midi configuration window Buttons Midi Enable Enables the Midi protocol processing Mdi Disable Disables the Midi protocol processing OK Saves all changes and goes back to the Setup menu Cancel Goes back to the Setup menu without saving any change Some examples that refer to the configuration showed on above picture Note On 9 e Trigsthe current cuelist nn must be different from 0 Note On eS i eee CU nn must be different from 0 Note On nn must be different from 0 Control Change a ae Sets the master speed level of cue list 10 to 200 Control Change Sets the master size of cue list 11 to 80 Program Change ie Set the page 11 as the current page Pag 58 RedMx 1 06 8 DMX IN INPUT The Dmx input allows you to connect a generi
71. ponding cue which becomes active and is transmitted In this way the cues of the cue list can be activated in any given order depending on your requirements at any given time The timings of the cues are the ones inserted in Qlist mode this window due to space and opportunity does not allow to insert times therefore this activity is to be performed with the cue list in Qlist mode Once the timings have been inserted the Live mode can be set of course it is possible to return to the Qlist mode at any point to make amendments to the times and then return to the Live mode l Cue list mode selection buttons 2 Cue status led red last triggered cue yellw previously triggered cue Size100 Speed 100 Master 100 Cue list in Live mode Buttons Lock when activated to edit the current qlist a clear command is needed this can be given via the Select button otherwise simply trigger a qlist to make the cue list current Qlist Chase Sequence Live cue list mode selection buttons EDITOR recalls the editor window IMPORTANT in this mode the Lock button is particularly important as it ensures control of the cue list is not lost when other playbacks are activated The Live window is to be considered as an extension of the physical commands of the corresponding playback when changing page the Live window will show the cue list corresponding to the new page regardless of the Lock button status Only if the cue list is active will the
72. sible to obtain Mexican wave type effects by operating on the fourth wheel Spread and on the phase effect selection buttons Base _ j Size E N Dimmer A 0 Dimmer B 0 Period 5 0 Dread 100 Movement effects generator for pan and tilt Effects window 1 Selection phase Zi Parameter selection 3 Family attribute selection In the case of movement effects applied to the pan and tilt of the fixtures the situation is slightly different as the movement is defined by the central or base point which is set by pressing the palette buttons or operating on the first wheel and the amplitude set by using the second wheel In the case of the Circle effect the pan e tilt share the same amplitude value while the two values are independent from one another in all other cases The two Left Right and Sync No Sync buttons at the top are used to generate chasing effects in case two or more fixtures are used The Remove button removes the applied effect The Selector button recalls the selector window Pag 24 RedMx 1 06 Editing an effect To edit an effect which had previously been saved in a cue load the cue into the editor select the fixtures involved and finally open the window of the effects generator to edit If the show contains many fixtures and if one cue contains more groups of fixtures with different effects selecting the fixtures may be a difficult task In this case the Selector window helps analyse the co
73. ssing result in practice when the slider is at zero the controller cannot give any input if the slider is at 100 the controller s cue is transmitted in intermediate cases the actual contribution of the controller depends on how the controller cue has been saved All channel fade the final value is the linear combination between the value of the controller and the result of the processing of the cues the closer the slider is to 100 the greater the influence is of the controller and the lower the cue input and vice versa linear path e Snap Start channels which have path Linear follow the All channel fade criteria while to channels with path Snap_start or Snap_end the following criteria is applied if the slider is O the value of the playback cues appears the controller gives no input if the slider is above 0 the controller value appears o Snap End the channels which have path Linear follow the All channel fade criteria while the channels with path Snap_start or Snap_end the following criteria is applied If the slider is lower than 100 the value of the playback cues appears the controller gives no input if the slider is equal to 100 the value of the controller appears Saving a manual cue To save a cue in a controller press Store the flash of the controller press and hold the Store key while pressing the flash key on the controller Cues can be saved in 3 different ways All channel fade Snap Start or
74. st is taken to the stored position 6 list of fixtures that make up the show Each button has two leds the first 7 indicates whether the fixture is being controlled by the editor if it is green then all parameters are controlled by the editor if it is switched off the editor does not control any parameter of the fixture in the other cases the led turns orange The second led 8 indicated whether the fixture is selected red led or not led off 7 report of fixtures controlled by the editor This led can be switched off the editor does not control any parameter of the fixture e green the editor controls all fixture parameters e orange the editor controls only certain channels of the fixture 8 report of selected fixture This led can be e switched off the fixture is not selected e red the fixture is not selected 9 wheel tag This tag indicates both which attribute is being controlled by the wheels and its value If the value is not absolute but paletted the name of the palette is displayed When the wheel controls the parameters of two or more fixtures that do not have the same value is displayed If the wheel does not control any attribute the string is displayed 10 value bar Anaplayback representation of the parameter value controlled by the wheels 11 parameter status This led can be switched off all parameters associated to the wheel are Empty i e they
75. te When you save a cue only the assigned attributes are saved and the Empty attributes are disregarded Fixture a generic term for any projector or device connected to the console via Dmx or Artnet and controlled by the latter Manual cue cue to be associated to a controller unlike standard cues it does not have timing or effects Page group of 24 cue lists associated to the 24 Playbacks on the console By changing page a new set of 24 cue lists will be associated to the playbacks Palette status of one or more attributes related to one or more fixtures to be conveniently used for creating cues Updating a palette entails automatically upgrading all cues involved Playback a feature which allows you to control a cue list A cue list can be saved edited and aired only if it is associated with a playback It can consist of a single key or two keys and a slider if internal depending on the configuration of the console or of three keys and a slider if these belong to the expansion Parameter see Attribute Switch or Key physical interface button Key see Switch Trigger event which determines the activation of a cue Pag 7 RedMx 1 06 PART 1 QUICK START GUIDE 1 OVERVIEW OF THE CONSOLE Rear panel 1 Controller status 2 Configurable controllers 3 Playbacks 4 Edit keys 5 Main touchscreen 6 Encoder wheels 7 Grand Master e DBO 8 Pan amp Tilt pointings 9 Expansion connector 1 and
76. ton and using the third wheel Edit value to set the new value The exit button closes the window and goes back to the Setup menu Ls 40 ex te Attribute scroll Fixture scroll Edit value Fixture configuration window Controller configuration See Controllers section Pag 43 RedMx 1 06 Pan tilt options This window allows to invert and swap the Pan Tilt functions for each fixture used in the show Fiturename name Pan inversion inversion Tilt inversion Tilt inversion Pan Tilt swap Pan Tilt swap swap m 13 Ls 40 ex icdiliecladdatl 15 Ls 40 ex ex Fixture scroll Pan tilt options window The first wheel together with the scrolling buttons on the left allows to scroll down all the show s fixtures which include a Pan Tilt function By clicking the option buttons for each fixture it is possible to separately select the Pan Tilt inversion and their swap The Save and Exit button saves all data and goes back to the Setup menu Data are also saved if the window is closed by using the context specific menu or the Edit Qlist button Artnet configuration The configuration window for the Ethernet port and the Artnet connector is divided in two parts the left part allows to configure the Ethernet port on the console while the right part allows to configure Artnet To edit the Static lp Subnet Mask Sub net and Universe fields it is necessary to push the corresponding button an
77. ups and various palettes to use positions colors gobo etc To recall the palette window simply press the Palette button located at the top in the editor To save a new palette bring up the Store menu by pressing the Menu key and then select one of the yellow buttons relating to the family of values that we want to save in fact when saving a palette not all the content in the editor is saved but only the parameter values that belong to the same family of the button pressed The palettes like the parameters of the fixtures are organized into 6 families Intensity Pan tilt Colors Gobos Prism and Blade the palettes displayed in the window are those relating to the current family which can be changed by pressing the Pag 15 RedMx 1 06 buttons on the left of the screen and ONLY those relating to the selected fixtures In the case that no fixture is selected all fixtures of the current family are displayed The console also contains 4 sets of default palettes Chris Gam Lee and Rosco usable on all fixtures that have RGB or CMY color mixing systems The current set can be selected in the General options window accessible from the Setup menu Playing or transmitting a cue To activate a cue just press the corresponding playback key Once the playback key is pressed the following cue is activated once the last one is reached it starts again from the first one The intensity master is set at 100 with the exceptio
78. ure Center if the number of fixtures is even the fixed value will be the intermediate value between the two central fixtures Offset wheel moves all values in parallel in the same direction increasing or reducing them in equal measure Amplitude wheel increases or decreases the amplitude of distribution negative values are also acceptable Pag 23 RedMx 1 06 Effects An effect is the predefined trend of a value which is repeated in cycle in time and which can be applied to any parameter of one or more fixtures speed and amplitude can be edited by the operator A typical effect is the Circle which when applied to the pan and tilt of the fixture force them to follow circular trajectories on the stage Different fixtures can share the same effect in order to move in a coordinated fashion To apply an effect to an attribute of the previously selected fixtures do as follows select the attribute interested by the effect by choosing its family to do so press one of the buttons on the right and then press one of the attribute buttons placed horizontally on the wheels e select the minimum and maximum values of the wave form by clicking on the palette buttons or operating on the first two wheels with the linear and square buttons it is possible to select the wave form respectively sinusoid and square wave e The third wheel Period enables to vary the speed of the effect When two or more fixtures are involved it is pos
79. w row of values to the selected command e Rename Cmd Opens the digital keyboard to rename the selected command e Delete Cmd Completely deletes after asking to confirm the selected command e Delete Row Completely deletes after asking to confirm the selected row Palette window The fixture could be now considered as completed but predefined palettes can also be added In order to do so press the Palettes button to open the Palette window Pag 52 RedMx 1 06 Palette list Palette body Scroll Palette Parameter Value Scroll Parameters Palette window The information necessary for inserting a new palette is name type Int PT Color Gobos Prism or Blade and the state of the features affected by the palette palette body Pressing the New Palette button activates the digital keyboard allowing to type in a name for the new palette to be created Afterwards the palette can be assigned a type and a value for each channel affected by using the wheels Channels not affected by the palette must be set to The window includes several buttons for editing data e New Palette Allows to insert a new palette e Move Up e Move Down Moves the selected palette respectively up and down e Rename Palette Allows to change the name of a selected palette e Delete Palette Permanently delete the current palette after confirmation e View Active Parameters Displays in the palette body only the parameters which are actua
80. wed by an Edit stage during which the activation times are amended and it is often necessary to return to the Record mode in order to add any missing events Execution of the list of events To execute the list of events set it to Play mode In order for the list to be correctly processed it has to be in the right chronoplaybackical order the Sort button when the list is in Edit mode serves this purpose In Play mode the received timecode is constantly compared against the events on the list which are activated when necessary Smpte Connection The Smpte input of the console is made up of an audio transformer connected to pins 2 and 3 of the XLR connector See picture below and is suitable for directly connecting a Smpte device with differential output The galvanically isolated structure of the input allows to use a Smpte source with a single ended output by connecting the hot wire and the signal mass respectively to pins 2 and 3 of the XLR connector After connecting verify that the Smpte frames are scrolling on the status bar in the top right hand corner of the Smpte window SMPTE INPUT SECTION Audio transformer To SMPTE Receiver CHASSIS SMPTE input section schematic Pag 56 RedMx 1 06 7 MIDI INTERFACE The main playback functions of the console can be controlled by MIDI comunication protocol this can be usefull for controlling and or syncronizing the console playback by any device capable of trasmitting Mid
81. xecuted in a reversed order e Bounce the cues are executed from the first to the last and then backwards from the last to the first and so on e Random the cues are executed in a random order Pag 30 RedMx 1 06 Cue list mode selection buttons FA Cue selection leds red selected off not selected 3 Execution led off cue not in execution yellow cue execution completed red in execution 4 Delay time in seconds 5 Fade in time in seconds 6 Delay Fade in timeline bar Fade 51 Speed 60 bpm Master 100 Cue list in chase mode Buttons Unselect all Deselects all Qlists Lock when activated to edit the current qlist a clear command is needed this can be given via the Select button otherwise simply trigger a qlist to make the cue list current Qlist Chase Sequence Live cue list mode selection buttons EDITOR recalls the editor window Manual each cue must be activated by a manual trigger Auto the cues are automatically activated in sequence Forward Reverse Bounce e Random cue activation order selection buttons Wheels The first three wheels are used to set the timings which refer to all cues while the fourth wheel controls the window scrolling The common values which can be set with the wheels are e Fade percentage of cue time dedicated to Fade in Speed speed of the cue expressed in beats per minute the cue time in seconds is calculated as 60 Speed Master master of intensity If
82. y Backstore restore window Buttons Erase This button completely erases after asking to confirm the selected backup file Rename This button activates the virtual keyboard allowing to rename the selected backup file Restore This button erases after asking to confirm the current show and substitutes it with the selected backup file All data of the current show is deleted If necessary create a backup file for the current show before launching the Restore command Backup This button copies the current show on the selected disk Before copying the digital keyboard is displayed to type in a name for the new copy Both the internal disk and a USB drive cannot contain two backup files with the same name To avoid this the programme will ask whether to erase the pre existing file or to cancel the operation On the USB drive each backup consists of a folder containing all data concerning the show The name of these folders is the same as the one typed in for the backup file On the USB drive all backup files are saved in the Backup folder If the folder does not already exist the programme will automatically create it Export Import This button which becomes Import when the USB drive is selected allows to copy the current backup file on the USB drive when the internal disk is selected and vice versa when the USB drive is selected The backup file is copied from one EEEE E EE Pag 46 RedMx 1 06 disk to the ot
83. y to a USB drive and vice versa Pag 38 RedMx 1 06 Clear show Completely erases all show data including cue lists and patch data and restores default configuration Fixture libraries and all backup files stored in the internal memory are not erased Touch calibrations Touchscreen calibration In general the console is delivered with a properly calibrated touchscreen but it can be newly calibrated whenever needed To calibrate the screen touch the spots pointed out by the programme To go back to the Setup menu touch a blank spot on the screen Dmx in Playbacks configuration Program to configure the remote control of console playbacks by DMX input Dmx in Controllers configuration Program to configure the remote control of manual cues by DMX input Midi configuration Program to configure the remote control of the console by MIDI protocol Fixture builder A programme to create configuration files for a fixture not included in the library In order not to display the different fixture s technical details the console needs a fixture definition file for each of them consisting in an fdf or fxr file the console has full compatibility with fxr files from Pilot 3000 which form the fixture library This library can be expanded by the user by creating new fdf files with the programme fixture builder which can be recalled by clicking on the fixture builder button IMPORTANT it is recommended not to use this program wh

REDMX 1.06 USER MANUAL - Techni-Lux

Contents

Download Pdf Manuals

Related Search

Related Contents