• • • • •
Contents
1. other to Channel 2 the clock display can tell you which sensor has been activated by flashing ch 1 or ch 2 on the display Py en LY cn lle The light sensor s level of sensitivity can be adjusted Turn the Light rotary knob towards to make it more sensitive to light or to make it less sensitive to light Insert a thin blunt instrument into the hole below Reset to return to the default settings TECHNICAL SPECIFICATIONS TYPE DESCRIPTION Remote Unit Dimensions LxWxH 88 x 43 x 112 mm 3 46 x 1 69 x 4 41 inches Weight without battery 140 g 0 31 Ibs Remote Unit Motion Sensor Coverage Approx 5 metres Distance Motion Sensor Warm Up Approx 2 minutes after power on Time RF Frequency 433 MHz 30 metres 98 feet with no obstructions Power Remote Unit 3 x UM 3 AA 1 5V batteries or 4 5V AC Adaptor NOTE jt is recommended that you use alkaline batteries with this product for longer performance NOTE Design and specifications are subject to change without notice TROUBLESHOOTING PROBLEM SYMPTOM REMEDY Remote nightlight Does not activate 1 Adjust batteries AC adaptor the backlight 2 Check Control Clock switch is set to On 3 Check the Code switch on the nightlight matches the main unit Code display NOTICES Oregon Scientific will not be held liable for any bodily injury death property damages or any other claims of whatever2. Orecon REMOTE NIGHTLIGHT NR868 USER MANUAL USER MANUAL CONTENTS AAPP Introduction Key Features Front View Back View Safety And Care Safety Precautions Caring For This Getting Started Ae kad seaks aakaesaeaamae da Product Overview Package Contents Batteries AC Adaptor Nightlight Activating The Nightlight Using The Mode Button Activating The Clock Backlight Using The Control Button The Code Switch The Channel Switch Light Rotary Knob Reset Button Technical Specifications Troubleshooting Notices Statement Of Responsibility About Oregon Scientific EC Declaration Of Conformity INTRODUCTION Thank you for selecting the Oregon ScientificTM Remote Nightlight This device is designed as an accessory for the RF Wall Clock JMR868 The remote nightlight supports the following functions Continuous nightlight display e Sensor activated nightlight display lights up for 20 seconds when it detects movement in a dark room e Simultaneously activated nightlight and clock backlight by the sensor e Remotely activated clock backlight lights up for 10 seconds when the Light ON button on the nightlight is pressed Wall mount and table stand Keep this manual handy as you use your new product It contains practical step by step instructions as well as technical specifications and wa
3. atteries are a good power source for back up usage NIGHTLIGHT The nightlight can be activated independently to the clock unit You can set the nightlight to the following options il Nightlight On When the room is dark the nightlight will stay on Slide the Mode button to On 2 Nightlight Off The nightlight stays off all the time Slide the Mode button to Off 3 Nightlight Auto When the nightlight detects motion in a dark room it will light up for 20 seconds Slide the Mode button to Auto NOTE when the motion sensor on the nightlight is turned on it needs approximately 2 minutes to warm up before giving a response You can control the backlight of the clock through the nightlight You can set the backlight to the following options 1 Control On The clock backlight is controlled by the activation of the nightlight Slide the Clock Control switch to On 2 Control Off The nightlight does not control the clock backlight Slide the Clock Control switch to Off NOTE See the Clock Backlight section in your Wall Clock JMR868 Manual which shows you how to set the nightlight sensors to be activated at times specified by you The Code switch on the nightlight must be set to the same setting as the Code setting on the main unit The Code allows the nightlight to recognize the main unit s settings Up to 2 nightlights can be linked to 1 wall clock By setting 1 nightlight to Channel 1 and the
4. nature resulting from the misuse or negligence of the product whether intentional or unintentional Oregon Scientific will not be responsible for any deviations in the usage of the device from those specified in the user instructions or any unapproved alterations or repairs of the product ABOUT OREGON SCIENTIFIC lt Please insert texts gt EC DECLARATION OF CONFORMITY lt Please insert texts gt OreGon SCIENTIFIC REMOTE NIGHTLIGHT MODEL NR868 USER MANUAL
5. ng up and using this product Heat sources Keep the product away from heat sources such as radiators stoves heaters and other heat generating products Water and moisture Do not use the product in or near water or in high moisture areas such as a bathroom e Power source The product may be susceptible to power surges It should be unplugged during severe storms or whenever you will be away for a long time Only use the type of power source specified in this manual Do not overload power strips and extension cords as this can cause a fire hazard To ensure you receive the maximum benefit from using this product please observe the following guidelines Do not clean any part of the product with benzene thinner or other solvent chemicals this may cause permanent damage that is not covered by the guarantee When necessary clean it with a damp cloth Keep your product away from hot humid conditions or strong sunlight Every effort has been made to ensure the highest standards of reliability for your nightlight However if something does go wrong please do not try to repair it yourself consult your supplier Do not use your product outdoors in the rain or handle it with wet hands water can damage electrical equipment GETTING STARTED e The nightlight can be set independently to light up in the dark so you can see where you are going The clock and nightlight can also be used together
6. rnings you should know KEY FEATURES pare pe Rotary Motion Sensor Detects motion and activates the nightlight and clock backlight in accordance with the settings used Twist the knob to direct the sensor to the position you want Light Sensor Detects the light intensity of the environment Light ON Press to turn the clock backlight ON for 10 seconds remotely Power ON OFF Slide to the appropriate setting to turn the battery or AC power ON or OFF 4 5V Adaptor Socket Light Panel When activated the panel will light up LED Indicator v pope a R868 pare Wall Mount Hole Battery Compartment Uses 3 x UM 3 AA 1 5V batteries Channel 1 2 Slide to select either Channel 1 or Channel 2 Code switch Slide to change the Code Mode On Off Auto Slide switch to ON the nightlight will turn on in a dark room Slide switch to OFF the nightlight is turned off Slide switch to AUTO the nightlight will only be activated by motion in a dark room Clock Control On Off Slide switch to ON when motion is detected the clock backlight will be activated Slide switch to OFF the clock backlight will not be activated by the motion sensor Light Rotary knob Rotate to adjust the sensitivity of the light sensor Reset button Press to reset the nightlight SAFETY AND CARE Please observe the following safety precautions when setti
7. to turn the clock backlight on when you walk into a dark room or wave your arm from the comfort of your bed It can do this because the nightlight has 2 types of sensor One sensor responds to light and the other responds to movement From the clock unit you can set these sensors to be active during a certain period of time The clock can support up to 2 nightlights When you unpack your remote nightlight make sure you keep all the packing materials in a safe place in case you need to later transport the device or return it for servicing In the box you will find Remote Nightlight 3 x UM 3 AA 1 5V Batteries 4 5V AC Adapter NOTE Main Clock Unit JMR868 can be purchased separately The nightlight uses 3 x UM 3 AA 1 5V batteries To install the batteries simply insert them making sure they match the correct polarities and NOTE jt is recommended that you use alkaline batteries with this product for longer performance NOTE Change all the batteries at the same time it is dangerous to mix old and new batteries Protect your environment by taking exhausted batteries to authorized disposal stations The LED indicator on the motion sensor will flash in red when the batteries are low The 4 5V AC adaptor connects to the nightlight unit as shown below NOTE The nightlight has a Power ON OFF switch to help conserve power Use the AC adaptor when using the nightlight for long periods of time The b
Download Pdf Manuals
Related Search