13119 INSTALLATION INSTRUCTIONS 9"
Contents
1. DO NOT EXCEED VEHICLE MANUFACTURER S RECOMMENDED TOWING CAPACITY WARNING ALL NON TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS FAILURE TO PROPERLY SUPPORT NON TRAILER LOADS WILL VOID PRODUCT WARRANTY HAVING INSTALLATION QUESTIONS CALL TECHNICAL SUPPORT AT 1 800 798 0813 RUBBER ISOLATOR REMOVAL DIAGRAM This technique can be used if an Exhaust Hanger Removal Pliers is not available Using a 5 8 open end wrench slide the Y DRIVER SIDE wrench up to the rubber isolator cradling e ONS FRAME RAIL the hanger rod as shown Next place the flat edge of a pry bar between the wrench and the hanger stop or hanger rod Then simply rotate the pry bar toward the wrench to remove the rubber isolator Note Using a spray lubricant or soapy water on the hanger rod and the rubber isolator helps removal PASSENGER SIDE FRAME RAIL To remove debris from weldnuts in frame spray lubricant or compressed air into hole UNDERBODY PANEL For heavy debris use a SHOWN TRIMMED small wire brush Be careful not to damage threads CONICAL TOOTHED WASHER ORIENTATION DIAGRAM HITCH SIDE CONICAL TOOTHED CAL TOO feson INSTALLED HITCH INSTALLATION STEPS 1 Remove 10 fasteners and lower underbody panel 2 Lower exhaust by removing 2 rubber isolators from the hangers attached to the exhaust See RUBBER ISOLATOR REMOVAL DIAGRAM Mark and trim underbody panel Reattach u2. HROUGH 3 Mark and trim underbody panel Reattach underbody panel using fasteners removed in Step 1 Note Dimensions are approximate confirm fit prior to trimming Use ribs of the underbody panel as cutting guides EXISTING TOW LOOP CUT OUT 4 Insert 7 16 U bolt through tow hook as shown Raise hitch into position and secure using 7 16 flange nuts to the U bolt and 10mm bolts with 7 16 conical toothed washers to the weldnuts in the frame rails de i To remove debris from weldnuts in frame spray lubricant or compressed air into hole For heavy debris use a small wire brush Be careful not to damage threads 5 Torque all 7 16 hardware to 50 ft lbs Torque all 10mm hardware to 48 ft lbs 6 Raise exhaust back into position For more information log onto www curtmfg com amp for helpful towing tips log onto www hitchinfo com HONDA CR V 1 28 2013 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH 3 500 LBS TRAILER WEIGHT amp 350 LBS TONGUE WEIGHT DO NOT EXCEED VEHICLE MANUFACTURER S RECOMMENDED TOWING CAPACITY WARNING ALL NON TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS FAILURE TO PROPERLY SUPPORT NON TRAILER LOADS WILL VOID PRODUCT WARRANTY HAVING INSTALLATION QUESTIONS CALL TECHNICAL SUPPORT AT 1 800 798 0813 Parts List ITEM QTY PART NUMBER DESCRIPTION N PASSENGER SIDE SQ 7 16 CONICAL TOOTHED WASHER 7_16 14
3. Safety glasses should be worn at all times while installing this product 13119 INSTALLATION INSTRUCTIONS WEIGHT CARRYING TRAILER WEIGHT 3 500 LBS TONGUE WEIGHT 350 LBS INSTALLATION TIPS VEHICLE PHOTO THE INSTALL TIME LISTED IS FOR PROFESSIONAL 4 BEFORE YOU BEGIN INSTALLATION READ ALL INSTALLERS IF YOU ARE HESITANT TO UNDERTAKE INSTRUCTIONS THOROUGHLY THIS TASK ON YOUR OWN CONTACT AN AUTHORIZED 7 1O FASE INSTALLATION 2 PEOPLE MAY BE CURT INSTALLER FOR ADDITIONAL ASSISTANCE REQUIRED 3 USING PROPER TOOLS WILL GREATLY IMPROVE THE QUALITY OF THE INSTALL AND REDUCE THE INSTALLATION REQUIRES TIME REQUIRED J 4 NEED HELP OR HAVE SOME QUESTIONS l CALL TECHNICAL SUPPORT AT 800 798 0813 9 W amp TORQUE SOCKET WRENCH EXTENSION CHALLENGING as 10mm 17mm _ a 11 16 HITCH ILLUSTRATION SCREW UNDERBODY PANEL DRIVER Oen TRIMMING REQUIRED LOWER EXHAUST MAKE SURE YOUR HITCH MATCHES PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND CURT Manufacturing LLC warrants this product to be free of defects in material and or workmanship at the time of retail purchase by the original purchaser If the product is found to be defective Curt Manufacturing LLC may repair or replace the product at their option when the product is returned prepaid with proof of purchase Alteration to misuse of or improper installati
4. nderbody panel using fasteners removed in Step 1 Note Dimensions are approximate confirm fit prior to trimming Use ribs of the underbody panel as cutting guides See Underbody panel trim diagram Insert 7 16 U bolt through tow hook as shown Raise hitch into position and secure using 7 16 flange nuts to the U bolt and 10mm bolts with 7 16 conical toothed washers to the weldnuts in the frame rails See WELDNUT CLEANING DIAGRAM Torque all 7 16 hardware to 50 ft lbs Torque all 10mm hardware to 48 ft lbs Raise exhaust back into position PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND Curt Manufacturing LLC warrants this product to be free of defects in material and or workmanship at the time of retail purchase by the original purchaser If the product is found to be defective Curt Manufacturing LLC may repair or replace the product at their option when the product is returned prepaid with proof of purchase Alteration to misuse of or improper installation of this product voids the warranty Curt Manufacturing LLC s liability is limited to repair or replacement of products found to be defective and specifically excludes liability for incidental or consequential loss or damage
5. on of this product voids the warranty Curt Manufacturing LLC s liability is limited to repair or replacement of products found to be defective and specifically excludes liability for incidental or consequential loss or damage For more information log onto www curtmfg com amp for helpful towing tips log onto www hitchinfo com 1 28 2013 NO DRILLING REQUIRED REPRESENTATIVE PHOTO INSTALLATION WALKTHROUGH REMOVE O a TENES ee eee race noovipanel ITEM PART NUMBER DESCRIPTION 7 16 14x 1 75 x 1 00 C C U BOLT 7 16 14 HEX FLANGE NUT M10 1 25 x 30 HEX BOLT 7 16 CONICAL TOOTHED WASHER CONICAL TOOTHED WASHER ORIENTATION DIAGRAM VEHICLE FRAME HITCH SIDE PLATE CONICAL TOOTHED WASHER HEX BOLT 2 Lower exhaust by removing 2 rubber isolators from the hangers attached to the exhaust RUBBER ISOLATOR REMOVAL DIAGRAM This technique can be used if an Exhaust Hanger Removal Pliers is not available Using a 5 8 open end wrench slide the wrench up to the rubber isolator cradling the hanger rod as shown Next place the flat edge of a pry bar between the wrench and the hanger stop or hanger rod Then simply rotate the pry bar toward the wrench to remove the rubber isolator Note Using a spray lubricant or soapy water on the hanger rod and the rubber isolator helps removal For more information log onto www curtmfg com amp for helpful towing tips log onto www hitchinfo com INSTALLATION WALKT
6. x 1 75 x 1 00 C C U BOLT JOC eee RUBBER ISOLATOR RACHET TORQUE WRENCH 9 EXTENSION 10mm SOCKET 17mm SOCKET 11 16 SOCKET SCREW DRIVER ROTARY TOOL SAFETY GLASSES MUFFLER TRUNK PAN WELDNUTS BOTH SIDES DRIVER SIDE FRAME RAIL TOW LOOP NOTE DIMENSIONS ARE APPROXIMATE CONFIRM FIT PRIOR TO TRIMMING EXISTING TOW LOOP CUT OUT HITCH WEIGHT 30 LBS INSTALL TIME PROFESSIONAL 30 MINUTES NOVICE DIY _60 MINUTES INSTALL NOTES NO DRILLING REQUIRED STRING EEGUIRED UNDERBODY PANEL TRIM DIAGRAM LOWER EXHAUST PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND Curt Manufacturing LLC warrants this product to be free of defects in material and or workmanship at the time of retail purchase by the original purchaser If the product is found to be defective Curt Manufacturing LLC may repair or replace the product at their option when the product is returned prepaid with proof of purchase Alteration to misuse of or improper installation of this product voids the warranty Curt Manufacturing LLC s liability is limited to repair or replacement of products found to be defective and specifically excludes liability for incidental or consequential loss or damage 13119 HONDA CR V GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH 3 500 LBS TRAILER WEIGHT amp 350 LBS TONGUE WEIGHT
Download Pdf Manuals
Related Search