Home

guide

1. Z y D Upper Original Feeder Upper Original Feeder accepts a sheet type original that is 0 05 0 1mm in thickness Please set the original with face up The original fed from here Feeder is ejected to the front side of scanner via Lower Original Feeder Lower Original Feeder Lower original Feeder accepts a sheet type original that is 0 05 1 49mm in thickness as well as a board type original that is 1 5 16 0mm in thickness Please set the original with face down The original fed from here is ejected to the rear side of scanner and received by the Rear Steel Tray Upper Original Feeder This lights green when the Upper Original Feeder can accepts original Indicator insertion Lower Original Feeder This lights green when the Lower Original Feeder can accepts original Indicator insertion And in the Board Original Mode it blinks green when the scanner detects original Original Guides These guides can be shifter left and right according to the original width and prevent the original from skewing during scanning vers Board Lamp lights green when the Board Original Mode is enabled Stop Button amp Lamp Pressing the Stop Button during scanning will stop scanning and original transportation in the middle and one more will eject the original to either front or rear Power Lamp This shows the status of scanner Blinking in green During initialization not ready Lighting in green Ready for scanning or during scanning Ligh
2. KIP 2300 User Guide We highly appreciate your purchasing our KIP 2300 Image Scanner This User s Manual contains functional and operational explanation for KIP 2300 Image Scanner Read this User s Manual carefully before use in order to understand the KIP 2300 Image Scanner completely and to use more efficiently Keep this User s Manual for future reference 1 For U S A This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 For Europe This equipment complies with the requirements in Pub 22 of CISPR Rules for a Class B computing device Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take whatever steps are necessary to correct the interference Do not install Machine around electronics equipment or precision instruments It may be influenced by electrical reason or vibration while operation If Machine is installed near electronics equipment such as TV or radio interference to equipment such as noise or flickering may be occurred Use separate power line and install Machine as far as such equipment As an ENERGY STAR Partner Katsuragawa Electric Co Ltd has determined ae that this product meets the ENERGY STAR
3. Platen and Feeding Rollers once a week or as needed Dirt of these parts may result in the image problem or getting dirt on the scan original 4 1 1 Document Glass Open the scanner upper unit Wipe the Document Glass with a soft cloth with a little water or with neutral detergent first and wipe it with a dry soft cloth Document Glass 4 1 A CAUTION The Document Glass can be removed if the thumb screws on both sides and the brackets are removed But do not touch this screw as only the service technician is allowed for removing the Document Glass If the Document Glass is removed some foreign substance may drop into the machine and may cause several troubles as short circuit Do not touch this screw 4 2 4 1 2 Platen Wipe the entire white part of the Platen with a soft cloth with a little water or with neutral detergent first and wipe it with a dry soft cloth Platen Clean the entire white part 4 3
4. guidelines for energy efficiency Ur The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving through the penetration of energy efficient computers and other office equipment The program backs the development and dissemination of products with functions that effectively reduce energy consumption It is an open system in which business proprietors can participate voluntarily The targeted products are office equipment such as computers monitors printers facsimiles copiers scanners and multifunction devices Their standards and logos are uniform among participating nations The symbol shown indicates that this product conforms to Directive 2002 96 EC of the European Parliament and the council of 27 January 2003 on waste electrical and electronic equipment WEEE and does not apply to countries outside of EU Only For EU Member States The symbol shown indicates that this product conforms to SJ T 11364 2006 of People s Republic of China Electronic Industry Standard and does not apply to countries outside of People s Republic of China The symbol shown indicates that this product conforms to GB 18455 2001 11364 2006 of National Standard of the People s Republic of China and does not apply to countries outside of People s Republic of China WARNING FOR THE SAFETY OBSERVE THESE WARNING Following warnings are very important to use this equipment safely and to prev
5. ctrical reason or vibration while operation If Machine is installed near electronics equipment such as TV or radio interference to equipment such as noise or flickering may be occurred Use separate power line and install Machine as far as such equipment 1 2 h 2 Specifications Model KIP2300 Image Scanner Type Desktop scanner Reading sensor 3 CCD Reduction Optical System 3 CCD of RGB 7450 pixels Optical Resolution Main scanning horizontal direction 600dpi Sub scanning vertical direction 600dpi Range of Scan Resolution Scan mode Binary mode 8 bit gray mode 24 bit color mode Scanning method Scan speed Monochrome Gray mode 100dpi 12 sec lower feeder 5 sec upper feeder 600dpi 5 sec lower feeder 5 sec upper feeder 2400dpi 1 25 sec lower feeder 1 25 sec upper feeder Color Mode 100dpi 12 sec lower feeder 5 sec upper feeder 600dpi 2 sec lower feeder 2 sec upper feeder 2400dpi 0 5 sec lower feeder 0 5 sec upper feeder Sheet type amp board type Upper original feeder can accept 0 05 0 1mm Lower original feeder can accept 0 05 16 0mm Maximum reading width 914 4mm 36 Transportable original Max 16 000mm length Min 210mm Original type NOTE 48 is the maximum length for board type original Transportable original Max 1066 8mm 42 width Min 210mm Thickness of original Ma
6. eady 2 2 Auto Power OFF KIP 2300 has Auto Power OFF feature for energy saving purpose which automatically switches off the scanner when 15 minutes of inactive period has passed Please turn on the scanner again with the Power Switch for using the scanner again Power switch 2 2 3 1 Original Misfeed When the original is mis fed during scanning remove it manually as instructed in below 3 1 When feeding into upper original feeder 1 Open the document upper cover with holding both sides Document upper cover Hold here when opening the document upper cover 2 Pull up both blue levers to open the scanner upper unit Blue levers 3 1 3 Remove the mis fed original Mis fed original A CAUTION Take cere not to catch your hand when closing the document upper cover or scanner upper unit 3 2 3 2 When feeding into lower original feeder 1 Open the scanner upper unit by pulling up the blue levers on both sides Blue levers 2 Remove the mis fed original Mis fed original A CAUTION Take cere not to catch your hand when closing the scanner upper unit 3 3 3 2 Error The Power Lamp lights in red when the scanner has any error See the description of error indicated on the controller monitor and correct the error appropriately Power Lamp lights in red when any error occurs 4 1 Cleaning lt is recommended to clean Original Glass
7. ent the operator from danger and his her property from being damaged Hazardous or damage degree is classified and shown as follows when this machine is erroneously used ignoring this USER S MANUAL WARNING This caution mark denotes that the failure to follow given instructions in handling the machine could result in a death or serious injury CAUTION This caution mark denotes that the failure to follow given instructions in handling the machine could result in an injury or physical damage only This symbol signifies what must not be done This symbol signifies General Mandatory Action WARNING Connect the scanner and Ground with each other surely with the grounding wire Otherwise it is dangerous for you if you receive an electric shock or at the time of lightning If the outlet does not have a Grounding Terminal or if it is impossible to connect call the vendor or service professional for the installation Power source should be rated from 100V 240V 6 10 6A or higher and 50 60Hz It is preferable that the used power circuit is provided with a dedicated breaker Install the machine as close as possible to the outlet When you wish to move the machine to another place make sure to ask your service engineer the outlet abnormally and cause a fire Do not put anything heavy on the power cord It may cause a fire or receiving an electric shock Do not step on the power cord and do not damage or p
8. ipment 4 The temperature must be within 10 through 32 degrees centigrade and the humidity must be within 20 through 80 5 Keep the equipment away from fire dust and direct sunlight If it is impossible to avoid the direct sunlight please pull the curtain to intercept the sunlight 7 Keep enough space around the machine as follows The following values are the least requirements Please keep a wider space if possible pp 1600mm Rear side lee y KIP2300 Front side 1000mm 2000mm is required if the original is thicker than 1 2mm 1 1 Reference Machine Noise Information Ordinance 3 GSGV January 18 1991 The maximum sound pressure level is equal or less than 70dB A according to ISO 7779 A NOTE 1 For U S A This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 For Europe This equipment complies with the requirements in Pub 22 of CISPR Rules for a Class B computing device Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take whatever steps are necessary to correct the interference Do not install Machine around electronics equipment or precision instruments It may be influenced by ele
9. result in a fire or receiving an electric shock If nobody operates the scanner in the night time make sure to turn it off for the safety If nobody operates the machine for a long time during consecutive holidays make sure to turn it off for the safety Nothing should be put near the power plug so as to disconnect it quickly anytime LED Safety Safety of LED Products Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure As the LED on the Light Source PCBs PW12130 amp PW12131 are Class 2 LED singularly it is not allowed for using it with disassembling or converting Classification of LED product CLASS 1 LED PRODUCT IEC 60825 1 2001 EN 60825 1 1994 A2 2001 A1 2002 Maximum class of the embedded LED CLASS 2 WHITE LED Maximum power 4 0mW 1 1 Installation Requirements The following conditions have to be satisfied when installing the KIP2300 Scanner 1 Satisfy the following input power condition Voltage 100 240V 6 10 Current 6A or higher Frequency 50 or 60Hz KIP2300 can be connected to the outlet simply so far as the voltage is within 100 240V 6 and 10 are acceptable 2 Connect the power plug to the grounded outlet 3 To completely disconnect the equipment from the power source please draw the power plug from the outlet The outlet must be easily accessible near the equ
10. rocess it It may also cause a fire or receiving an electric shock Do not tie the power cord or make a knot on it It may also cause a fire or receiving an electric shock Do not put a flower vase a flowerpot or a water filled glass on the top of the machine If the water spilt out it may also cause a fire or receiving an electric shock If the machine generates abnormal smell or noise turn it off and then disconnect the power plug from the outlet necessarily Do not handle the power plug with the wet hand positively It may cause to receive an electric shock Insert the power plug into the outlet completely If the power plug is not inserted completely it may cause a fire Use only the attached power cord Make sure to catch the Plug when you unplug the machine Otherwise you may break the cord and may result in a fire or receiving an electric shock S Do not use a multi wiring connector that might raise the temperature of Do not disassemble or tamper the machine Otherwise it may cause a fire or receiving an electric shock N CAUTION Do not install the machine at the following places 1 Humidified or dusty place 2 Unstable floor When the machine comes down it may cause the injury Be careful not to catch your hand between Upper Unit and Main Unit when you close the Upper Unit Unplug the machine before you move it to another place Otherwise the power cord may be damaged and may
11. ting in orange Scanning original transportation is paused Blinking in orange Ejecting the original Lighting in red Scanner has any error Front Steel Tray Helps feeding a board type original into the Lower Original Feeder Rear Steel Tray Receives the original ejected from the scanner after scanning rn us Max number of originals about 50 sheets of 36 x48 Max weight of originals 5kg square meter we 7 1 6 1 4 2 Rear view zz h Name Rear Counter Rollers Help to transport the original when ejected 2 USB Terminal USB cable is connected Connected to the PC Type B Connector 5V max u HIL Terminal HIL Connector is connected Connected to the PC 5V max 1 7 2 1 Turning ON OFF 1 Prepare a power cable that satisfies the following specifications 2 Connect the KIP2300 scanner to the outlet via the power cable 3 Turn on the KIP2300 scanner pressing the bar side of Power Switch on the left Press this side for turning on 4 Scanner takes initialization It takes about 10 seconds for the initialization and the scanner does not accept original insertion during this period which is shown by green flash of Power Lamp Power Lamp flashes before ready 2 1 5 Scanner gets ready when all the initializations are finished which is shown by continuous lighting of Power Lamp in green Power Lamp lights when r
12. x 16mm Min 0 05mm Centered White LED Less than 10 seconds 256MB DDR DIMM Windows 7 Vista XP amp 2000 NOTE KIP2300 supports only 32 bit version of the above OS USB 2 0 for controlling amp image data transfer HIL High speed Image Link for image data transfer Placement of original Light source Warm up time Memory Operation system Interface NOTE Connected PC needs to have a PCI Express card slot for installing the HIL Add in Card A NOTE Specifications may change without notification 1 3 Power source Voltage 100 240V 6 10 Frequency 50 or 60Hz Average power US 120V consumption During scanning Standby In Power Save Mode OW EUR ASIA 200 240V During scanning Stand by In Power Save Mode OW Dimension 1 366mm Width x 543mm Depth x 323mm Height NOTE Original Guides Original Tray and Pedestal are excluded Environmental conditions Temperature 10 32 degrees centigrade Humidity 15 85 RH No dew Recommended 23 degrees centigrade and 60 RH No dew Acoustic noise Stand by Less than 55db During scanning Less than 60db Impulse sound Less than 70db Pedestal Scanner Stand A NOTE Specifications may change without notification 1 4 N a m e amp Fr u n C ti Ion O f E a C h P a rt 4 r O n tv ie W 4 1 N 4

guide

Contents

Download Pdf Manuals

Related Search

Related Contents