RRC-330
Contents
1. is set you can put the next empty core on the ACH without readjusting the Locking Levers OPERATION 1 Place the STOP RUN Switch in the STOP Position 2 Place your Roll of Labels on the Roll Holder at the left of the RRC 330 The Take Up Spindle on the right rotates in a counter clockwise direction Note that your rewind can be Wind In or Wind Out according to which way you place the Label Roll on the Roll Holder right side up or upside down 3 The 2 plastic rings on the paper guides need to be used only if the unwind roll is unevenly wound to begin with Setting the rings at the proper height will correct the unevenness of the roll on the rewind side 4 The machine will stop when out of paper To re start load paper and set the Stop Run Switch to STOP Re set the counter if necessary Start by switching to RUN 5 Place an empty label Core not included over the Take Up Spindle and secure the Label Web using a piece of tape 6 Enter the desired Label Count via the Push Buttons on the Counter If you do not use preset set the value to O IMPORTANT It is recommended to use the machine at its maximum speed Keep unwind plate clean of particles and glue2. set at 7 5V below 7 5V the machine sees no label and above 7 5V the machine sees a label MAINTENANCE Your RRC 330 requires no maintenance LABELMATE LLC 69 AVENUE ALPHONSE XIII 1180 BRUSSELS BELGIUM TEL 322 375 69 60 FAX 322 375 38 96 brussels labelmate com www labelmate com LABELMATE User_RRC 330 09 10 RRC 330 Reel to Reel Counter e Variable Speed Control e 6 Digit Digital Pre set Counter e 330mm 13 Roll Diameter Remove all parts from the shipping container and verify contents Package Contents e User Manual this document e RRC 330 Unit e Power Supply Module e Separate User Manual for Counter Unit Retain the Shipping Container and Packaging for Storage and Transport e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e SPECIFICATIONS Max Label Roll Weight Max Label Roll Size 6Kg 13 2Lb 330mm 13 diameter Power Supply Input 220 240VAC 50 60Hz Output 24VDC 4 17A Speed Min 65cm sec with 76mm take up roll diameter SET UP 1 Plug the Power Supply Output Cable to the Power Jack on the Rear Panel of the RRC 330 Plug the Power Supply into a suitable AC Power Mains Outlet Place the Power Switch on the rear of the RRC 330 to the ON 1 position Observe that numbers are displayed on the Counter See the separate User Manual for the Counter Modules itself for other operations 2 The Counter is pre programmed as a Preset Count Up Counte
3. LEFT SIDE CONTROL PANEL SPEED VARIABLE or MAXIMUM A two 2 position Selector Switch allows fa the user to select maximum MAX C i St speed not adjustable or adjustable speed set by the front panel Speed Control Knob The maximum speed in the VARIABLE position with the SPEED potentiometer fully clockwise is about 10 lower than the speed obtained in the MAX Speed position of the Speed Switch When the printing is correct the unit can be used at MAX Speed at all times PHOTOCELL ADJUST Potentiometer TEST Connector ADJUSTING THE LABEL DETECTOR PHOTOCELL TN PHOTOCELL SPEED ADJUST MAX VARIABLE The label detector photocell has been adjusted at the factory potentiometer fully CCW and requires no adjustment for a large variety of labels However some specific labels very transparent or relatively opaque backing paper might require adjustment of the photocell Using a voltmeter you can do a more accurate adjustment of the photocell Connect the provided test cable to the TEST connector on the side of the machine and connect the leads to a DC voltmeter with a range of 20V Load a roll of labels on the machine and position the backing paper in front of the photocell Make sure that the labels are tensioned when doing the test Set the voltage with the potentiometer to around 5V now put a label in front of the photocell the voltage should now be 10V or more The reference voltage in the machine is
4. r If you want to use the preset function introduce the number of labels with the blue push button on the counter If you do not want to use preset set the value to 0 3 When the preset number of labels is reached the RRC 330 will stop Pressing R on the counter will reset the count and restart the RRC 330 A WARNING This Product is for indoor use only Not for use in wet locations USING THE ADJUSTABLE CORE HOLDER 1 Unlock the three Locking Levers underneath the take up Flange by turning them clockwise If the Levers are difficult to grasp pull straight down on the Lever Arm and reposition the Arm so it is more or less perpendicular to the metal Hub 2 While holding the Take Up Flange rotate the black Plate underneath the Take Up Flange to bring the Fingers together 3 Place your Take Up Core over the Fingers about half way down and rotate the black Plate again to bring the fingers in contact with the Core Lock the Locking Levers by turning them counter clockwise Reposition the Lever Arms if necessary by pulling straight down and rotating them to a convenient position 4 Push the Core all the way down on the Fingers The Core should now be held tight on the fingers If not tight enough re do the operation 5 For easy removal of the roll from the ACH release one of the Locking Levers temporarily remove the Roll and re tighten the Locking Lever 6 Once the ACH diameter
Download Pdf Manuals
Related Search
RRC 330 rc 330 rc 330v rrc 340b rrc 340b percentage rc a330 for sale rc330tnb rc3300 rc330e2s11 rc330kn rc a330 rc330v 36s/940 psd w60l60 mxo rc330b rc330v 42s/940 seia w60l60 ia4 mxo