CONTENTS Pdf

Home

1. In this case the cycle time must be set to t0 00 During the cycle While the robot is operating the display screen shows the time remaining before the cleaning process is programmed to stop In automatic mode one can at any given time increase or reduce the amount of time remaining before the system stops by using the or buttons in 30 minute intervals However the Programme menu cannot be changed during the cycle You can also adjust the robot s operating mode When you press the button the TE or indicator is activated on the screen If the indicator is active the robot cleans the bottom and the sides of the pool If the E inicato is active the robot only cleans the bottom of the pool When you press the P button you move from automatic mode to manual mode and vice versa 15 The QP or O indicator shows the current mode auto or manual In antl mode pressing the buttons causes the robot to advance or reverse until the ania or the opposite direction s button is pressed When you press Q or E93 button the robot turns in the corresponding direction As soon as you release the button the robot continues in a straight line These 24 programmes are designed for the optimal performance of your robot They enable you to choose the parameters that are best suited to the dimen sions and the shape of your pool You should choose one of these programmes according to the width and the shape of your po
2. is not as clean as it should be when using your robot s automatic programme it only takes a minute to finish off the cleaning using the manual mode gt Do not leave your robot permanently in the water gt Disconnect the cable from the control box and wind it round the hooks on the trolley 18 IN THE EWENT OF A PROBLEM Your robot is fitted with a protection system for the motors in the event of a blockage A message appears on the screen EEO1 or EEQ2 or EE06 gt If a message numbered between EE04 and EE06 appears on the screen check that nothing is blocking the movement of the propeller or the brushes and re initialise the control unit by pressing both the ED and oie buttons at the same time gt If a message between EE01 and EE03 appears on the screen the problem is more serious and you should take the robot and the control unit in to your retailer 1 The robot is not functioning the screen remains blank and the buttons are not responding the power supply is not functioning Check the plug by plugging in a different electrical appliance Re connect the control unit s cable if the plug functions correctly 2 The robot is not staying on the bottom of the pool as it Should do or is regularly coming up towards the pool s surface There is still some air inside the system s shell Go back through the steps for submerging the robot respecting the recommendations given earlier in thi
3. Dear Customer Thank you for your confidence in choosing the LAZERNAUT from ZODIAC This product has been designed manufactured and tested with the utmost care in order to provide you with complete satisfaction We recommend you read these instructions carefully before using your LAZERNAUT They contain all the information you need in order to benefit fully from your LAZERNAUT in complete safety Please contact your retailer a swimming pool professional for any further information He will advise you on the usage and maintenance of your robot He can also supply you with spare parts and is qualified to provide you with after sales service CONTENTS _ HOW TO INSTALL YOUR LAZERNAUT Unpacking Installation Submerging the robot Electrical connections HOW TO USE YOUR LAZERNAUT Description of the control keyboard Functions of the 8 buttons and 5 indicators The control keyboard To start Programming the robot During the cycle Programmes HOW TO MAINTAIN YOUR ROBOT Cleaning the filter bag Changing the brushes Maintaining the robot IN THE EVENT OF A PROBLEM YOUR SAFETY CONFORMITY YOUR GUARANTEE The packaging should contain the following items HOW TO INSTALL YOUR G SaR including the control unit LAZERNAUT Check that your appliance has not suffered any damage during transport bumps broken parts etc If you detect the slightest problem please conta
4. ct your retailer immediately before using your LAZERNAUT gt Assembling the transport trolley Before removing the appliance from its box Pull the upper section of the trolley containing the control unit out of the box Remove the robot from the box being careful not to let the cable get caught up in the trolley Remove the lower section of the trolley Loosen the lock wheels completely and remove the screw from the axle pin Fit the upper section of the trolley into the lower section so that the control unit s keyboard is facing the front of the trolley Diagram 1 Fix the screws in place to hold the 2 sections of the trolley Diagram 1 together Be sure to position a plastic washer on both sides of these screws Tighten the lock wheels as far as they will go the lock wheels must face the back of the trolley Diagram 2 Make sure the cable wrap around hooks are facing backwards Diagram 3 lazernaut For your safety and for the LAZERNAUT to function correctly place the control unit at a distance of at least 3 5 metres from the edge of the pool making sure that the unit is not exposed to direct sunlight Diagram 2 Important Under no circumstances should anyone be allowed to swim when the LAZERNAUT is in your pool a Stage 1 Submerge the robot in the water and evacuate any air that it Diagram 3 contains by turning it over Diagram 4 TE ie lao O Stage 2 Squeeze the foam brushes with
5. erstood that these improvements cannot be added to previous models within the context of our guarantee If in spite of all the care and know how used in the manufacture of our products you were to have need of the guarantee please be aware that it only applies to the free replacement of faulty parts Transport and labour costs remain your responsibility The guarantee does not cover accidents breakage or deterioration due to causes unrelated to or independent of the recorded fault We are fully within our rights to cancel the guarantee if the appliance has been seen to by a third party not known to our workshops or by a technician who has not been approved by us or if modifications have been carried out without our written agreement We are also fully within our rights to cancel the guarantee in the event of usage that does not comply with the instructions provided with the appliance at the time of purchase gt Not covered by the guarantee gt Normal wear and tear of the operational parts such as the foam brushes or the filter bags gt Electrical damage caused by lightning or a bad electrical connection gt Breakage due to impact gt Under no circumstances can repairs or replacements made as part of the guarantee prolong the appliance s guarantee period 2 Period of guarantee The period of guarantee is fixed at three years from the date of invoicing the first user During the guarantee period defined above any
6. estroyed and hence the disposal operations When you dispose of this product comply with the local waste disposal instructions Do not throw it away in the middle of nowhere take it to a waste collection centre that specialises in used electrical and electronic products and or consult your dealer when buying a new product This appliance has been designed and manufactured in accordance with the following standards gt In compliance with Electromagnetic compatibility 2004 108 EC and the standards EN 55014 1 2000 A1 2001 A2 2002 EN 55014 2 1997 A1 2002 EN 61000 3 2 2000 A2 2005 EN 61000 3 3 1995 A1 2001 A2 2005 gt In compliance with Low Voltage Directive 2006 95 EC and the following standards EN 60335 1 2002 A1 2004 A2 2006 A11 2004 A12 2006 EN 60335 2 41 2003 A1 2004 The LAZERNAUT pool cleaning robot is labelled CE according to the following directives gt C E M 89 336 CEE and 92 31 CEE gt Low voltage 73 23 CEE 73 23 CEE vis a vis those to which it complies The product has been tested in normal usage conditions 20 YOUR GUARANTEE These terms are in accordance with French law at the time of printing 1 Conditions All our technical experience and concern for quality has been used in the construction of our equipment It has all been subjected to quality control tests Our models are regularly updated and improved to make the most of technological advances It is und
7. l mode Selection of Bottom Sides mode or Bottom only In automatic mode this button selects the Programme or Time menus During programming it C CANCEL cancels the choice that has been made for the Programme or the Time In manual mode this button turns the robot to the left while it is still underwater Diagram 7 on In automatic mode this button selects the Programme or Time menus During programming it validates the Programme or the Time choice In manual mode this button turns the robot to the right while it is still underwater In manual mode this button stops the movement of the robot Diagram 9 NB the pump is still functioning In automatic mode this button increases the programme numbers or the length of the cleaning process In manual mode pressing this button makes the robot go forward In automatic mode this button reduces the programme numbers or the length of the cleaning process In manual mode pressing this button makes the robot go backwards Diagram 8 Indicators These are logos in front of which small triangles appear when the mode that they represent is active e 0 lt p Automatic mode Manual mode B Cleaning of the bottom and of the sides of the swimming pool D of the bottom only O Stop button for the robot Diagram 9 14 i Diagram T1 The control keyboard When switched on the robot is in sleep mode and the display is bla
8. mend that you change the brushes at the end of each season It is imperative that they are changed if they are noticeably worn gt Turn the robot over gt Lift up the clip that is located between the 2 rollers Diagram 20 Bring them together so that you can free their extremity from the 4 pins attached to the drive unit Diagram 21 and then remove the brush holder Diagram 22 gt Remove the used brushes from the rollers and replace them with new ones gt Join the 2 rollers reposition them and then move them apart again making sure that their extremity is properly fitted to the 4 pins attached to the drive unit gt Lock the central clip the clip shows that the rollers are properly attached to the unit Diagram 23 Important To get the best out of your LAZERNAUT run in the foam pads To do this carry out four 1 hour cleaning cycles in bott mode see paragraph Programming the Robot page 15 In order that your robot retains its original appearance we suggest that you follow the recommendations given below gt The robot must be cleaned regularly in tap water or slightly soapy water without using any solvents such as trichlorethylene Rinse thoroughly gt Clean the filter bag at the end of each cycle gt Use your robot vacuum cleaner as often as possible your pool will always be wonderfully clean and the filter bag will not clog up so quickly gt If part of the pool
9. nk The robot is now waiting for a start or programming command To start When the Qoton is pressed the robot starts in automatic mode Diagram 10 A small triangle appears opposite the indicator on the top right hand side of the screen and the and B or mode indicators The programme the length of operation time and the bottom only or bottom sides parameters are those memorised during the previous cleaning cycle The amount of time remaining before the system is due to stop appears on the screen Diagram 11 When the robot is in sleep mode pressing any button except Programming of the robot takes one into the programming mode The screen displays the length of the cycle By pressing Qro E93 one moves alternatively between the Time and the Programme menu The active menu is shown on the display t time P Programme The possible values are increased or decreased using the Q buttons Example for the programmes P 01 P 02 03 Q Piece P 00 P 01 See chapter Programmes page 16 for selecting programmes The modified value flashes and is then validated by g or cancelled by ED cancel The length of the cycle can be set for 30 min to 6 hours in 30 minute intervals using the or O tons You can also use a programming clock not supplied the robot starts and stops automatically according to the time and programming parameters that you have defined using this clock
10. ol To activate one of these programmes refer to chapter Programming the robot on page 15 The programmes in the robot s memory are The Lazernaut is controlled by a microprocessor to ensure optimal cleaning in all pool configurations This microprocessor also offers the following functions Poolside system In the event that your Lazernaut comes out of the pool onto a poolside surface the microprocessor is able to detect the lack of water The robot turns around and goes back into the pool to continue cleaning Out of water security system If the Lazernaut does not succeed in going back into the water or if the robot is started out of the water the microprocessor shuts off the robot s power supply after approximately 20 seconds to avoid damage to the waterproof joints 16 ae oo moe sa q 5 Era A 4 X hi YOUR E a E D oS GZ 3 Diagram 14 Diagram 17 HOW TO MAINTAIN ROBOT Cleaning the filter bag We recommend that you clean the filter bag at the end of each cycle gt Bring the robot in by pulling on the cable Diagam 12 or using the manual mode see page 14 for manual mode utilisation gt Switch the robot off and unplug the control unit from the mains gt As soon as the robot is out of the water pick it up by the handle and lay it upside down on the poolside so that you have access to the filter holder plate located benea
11. part recognised as faulty will be mended or exchanged by the manufacturer with a new part or in correct operating condition In all cases travel and labour costs will be the responsibility of the user In the event of a return to the workshop return transport costs will be the responsibility of the user but labour costs remain the responsibility of the manufacturer The immobilisation and the prevention of possession of an appliance in the event of any necessary repairs cannot give rise to compensation In all circumstances the legal guarantee of the seller continues to be applied in accordance with article 4 of decree n 78 464 of 24 March 1978 The legal guarantee of article 1641 of the civil code is applied 4 Transport damage Appliances always travel at the risk and peril of the user It is up to the user before taking delivery of the appliance to check that it is in perfect condition Under no circumstances can we be held responsible for transport damage 21
12. s document point by point Turn the robot right over and hold it underwater so that all the air trapped in the shell can escape Squeeze the foam pads to evacuate the air Leave the robot for a while operating in bottom only mode 3 The robot does not or has stopped climbing the sides There are 2 reasons for this gt the filter bag is full or has become clogged up it just needs cleaning gt although the water seems clear there are microscopic algae in your pool invisible to the naked eye that make the sides slippery and prevent the robot from climbing them Carry out shock treatment and lower the pH a little Do not leave the robot in the water during the shock treatment process 4 The robot is not moving and the screen is switched on Check that the robot s power cable is properly connected underneath the control unit Check that the O indicator is lit up If not press 3 The result of the cleaning process does not seem to he as good gt Clean the filter bag gt Check that the foam brushes have not deteriorated We recommend that you change the foam brushes at the end of each season 19 Your LAZERNAUT is manufactured according to the strictest standards To ensure complete safety when using your appliance please respect the following recommendations gt Only connect the control unit to a plug fitted with a security residual current protection system of 30 mA maximum gt Make sure the
13. socket outlet is always and easily accessible gt Make sure that the control unit is at least 3 5 metres from the edge of the pool and avoid exposure to direct sunlight gt On no account should you ever allow anyone to swim while the robot is in the pool If by accident the trolley were to fall into the water it is essential that you unplug the electric supply before recovering the trolley gt To avoid any risk of an electric shock never open the electric control unit Call a qualified technician gt Never try to repair the mains power cable Contact the Customer Services Department to have it replaced to avoid any danger gt Do not use the appliance in your pool if the water temperature is above 35 C gt Always disconnect the mains power lead after use and before doing any cleaning maintenance or servicing work This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety In accordance with the provisions of the Waste Electrical and Electronic Equipment WEEE 2002 96 EC Directive used electric and electronic products must be destroyed separately from normal household waste in order both to promote re use recycling and other forms of recovery and to reduce the quantity of waste to be d
14. th the robot Diagram 13 to 19 gt Push down on the outside of the 2 clips that hold the filter holder plate in position and free it from the robot still holding it upside down so that the debris stays in the bag The filter is attached to the plate gt Remove the filter from the plate There is slight resistance behind the clips gt Empty the bag and clean it with running water or if necessary with slightly soapy water If you use soap rinse it thoroughly whilst turning it over Do not wring it out You can also machine wash it following the instructions given on the label inside the bag gt Also rinse the filter holder plate and remove any debris caught under the valves gt Replace the bag in the filter holder plate by pressing down on the filter s frame in the corners and behind the clips so that the frame is firmly in position on the plate Important the bag must be facing the right way When the bag is in position on the filter holder plate the Zodiac label must be visible gt Fit the filter holder plate back onto the robot when the filter bag is dry and click it into place Make sure that the clip attachments are properly in place by pushing them outwards Diagram 16 gt Diagram 19 Diagram 19 Diagram 18 17 Diagram 20 Diagram 22 Diagram 23 Your robot is fitted with foam brushes mounted on a brush holder that consists of a male and a female roller We recom
15. your hands to push out the air and to allow water in Diagram 9 It is essential that the appliance sinks to the bottom of the pool and stays there without aid Stage 3 Lay out the cable on the pool leaving the float closest to the control unit on the pool s edging To get the best out of your LAZERNAUT run in the foam pads To do this carry out four 11 2 hour cleaning cycles in bottom only mode see paragraph Programming the Robot page 15 Electrical connections fernaut Connect the robot s cable to the control unit and lock the connector under the unit Diagram6 Only connectthe controlunittoa plug fitted with a security residual current protection system of 30 mA maximum if in doubt contact an electrician installer Diagram 9 Diagram 6 13 You can choose to run your LAZERNAUT in either automatic or manual mode To select the operation mode use the control keyboard located on the transport trolley Diagram 17 Description of the control keyboard The keyboard consists of 8 buttons micro contact and a screen with 4 figures and 5 indicators 5 buttons control usage in manual mode 4 directions and a stop button and the programming of the robot HOW TO USE 3 buttons provide access to the function modes of the robot Z n 8 YOUR LAZERNAUT vane Functions of the 8 buttons and 9 indicators Buttons The Start Stop button for the robot y Selection of automatic or manua

CONTENTS

Contents

Download Pdf Manuals

Related Search

Related Contents