USER AND MAINTENANCE MANUAL
Contents
1. gt the electrical specifications recorded under the machine The complete disc 6 can be considered to be a part subject to wear For the machine to operate properly it is recommended that a check is also made that the seal 13 is in good condition in particular the absence of any signs of tearing of the lip CLEANING The appliance should neither be cleaned in a jet of water nor with a high pressure spray 1 Put the appliance on stop position by pushing the On Off button and disconnect the plug 2 Remove the chute lever assembly and the grating disk 3 Wash the chute lever assembly the grating disc and the drawer with washing up detergent rinse dry and reassemble the unit 4 The frame is to be sponged clean then dried Polish from time to time with a non abrasive product for windows or a cleaning agent for metal 98102 US 5 2 03 2011 WN www santos fr TROUBLESHOOTING Identifying the cause of appliance stoppage precisely The appliance does not start figure 6 e Check the mains supply the condition of the supply cord e Check the position of the drawer 1 on its slideway 2 the position of the lever 4 no more than 2 cm outside the chute 3 The appliance stops further to an overload see the chapter motor overload safety feature MACHINE TECHNICAL SPECIFICATIONS 220 240 100 120 50 60 50 160 150uF 160V 250uF 160V Start relay 02409 02409B SANTOS reference or 09409 or2. 3 For electrocution risk protection reasons never plunge the base into water or any other liquid 4 Unplug the appliance before carrying out any work on it cleaning maintenance or repair 5 The use of spare parts other than certified SANTOS original parts is prohibited ELECTRICAL CONNECTION e The appliance s power supply is available in 3 voltages o 220 240V 50 Hz single phase o 220 240V 60 Hz single phase o 100 120V 50 60 Hz single phase Line_protection The appliance shall be connected only to a power 2 pole earth socket supplied by a branch circuit of suitable voltage The branch circuit shall have been established by a qualified electrician according to national and local codes and laws and provided with suitable protective equipments such as fuse circuit breaker etc as defined by these codes and laws CARE e Before connecting the machine check that the mains electrical voltage is the same as the voltage for your appliance Its value is shown gt either on the identification plate under the machine gt or on the identification plate on the last page of this manual e If the power cable is damaged it should be replaced by a special assembly available from approved SANTOS dealers or from SANTOS 98102 US 5 2 03 2011 WN www santos fr Sur USING FOR THE 1st TIME Take the precaution of carefully washing the drawer 1 and the disc 6 before using for the first time RECYCLING THE PROD
3. 01ED 02201FD Disc for cheese for fondues 02201GD e Grater no 2 is also appropriate for grating almonds and hazelnuts or for making breadcrumbs Ice crusher N9 e Designed in exactly the same way as Grater no 2 Ice Crusher no 9 only differs on the following points o specific disc with an adjustable knife to crush the ice cubes o Stainless steel sheet at the bottom of the drawer www santos fr 98102 US 5 2 03 2011 8 3 USING THE MACHINE usine figure 1 Prepare the pieces of cheese to be grated or the ice cubes beforehand 7 Make sure the drawer is correctly in place 1 operating is servo controlled by a safety device linked to the drawers presence For the ice crusher place the stainless steel sheet inside the drawer 3 Start the machine by operating the On Off button 5 4 Lift up the lever 4 insert a piece of cheese to be grated or ice cubes and push on the lever steadily without forcing 5 Repeat the above procedure as many times as necessary 6 After use stop the machine by operating the On Off Button 5 COMMENT removing the drawer 1 or lifting up the chute 3 stops the appliance from working figure 6 For easier cleaning do not leave food to dry in the drawer or on the grating disc CHANGING DISC Push the end of the lever 4 pull on the closing key 14 and remove the chute lever unit to get to the disc 6 figure 2 TAKING APART left handed thread figure 3
4. 09409B 650 3 5 Motor speed rpm 1500 1800 1500 1800 71 71 kg Packaged weight Drawer capacity Liters 1 These ratings are provided as a rough guide The exact electrical specifications can be found on the rating plate 2 Noise level measured with sound pressure appliance in operation 1 m from the machine s centerline in accordance with standards ISO 11201 1995 and ISO 4871 1996 on load Appliance placed on a work surface 75cm above the ground Microphone turned towards the appliance at 1 6 m from the floor and 1 m from the appliance 98102 US 5 2 03 2011 ay www santos fr 98102 US 5 2 03 2011 D D q 4 Q ei E Saar 220 240V 50Hz wiring diagram Marron Noir Condensateur Blanc Blanc 5 Sege S curit d 3 levier LINA 6 BI id Marron Noir dee l Relais de d marrage Marron Als 3 Marche Arr t P1 S curit tiroir Blanc 1 EN Blanc de 98102 US 5 2 03 2011 a www santos fr 100 120V 50 60Hz wiring diagram Bleu Noir T Condensateur Blanc S curit levier SW Marron 7 Noir Relais de 4 sx 3 d marrage Marche Arr t E E 11 ua bp P2 P1 Noir Securite tiroir LJ Blanc Noir Blanc Blanc L AJ Noir Noir 3 Vert jaune 9 d 98102 US 5 2 03 2011 a www santos fr Saar 220 240V 60HZ wiring diagram Rouge Bleu Blanc sum Ter Marron Blanc BI Noir e 2 Sec
5. ETY FEATURE amaa ele a 8 MAINTENANCE een 8 Dischargingthecapacitor eee 8 ce gg e A ee EM 8 A ME E ea 9 TROUBLE SHOOTING ass eee ae an leman era em emen meka ellerle ekeni elemek 10 Theappliancestopsfurhertoanoverload 10 MACHINE TECHNICAL SPECIFICATIONS enn eee 10 RER Kale eebe e Te 12 100 120V50 60Hz wiring diagram m 13 220 240V 60Hz wiringdiagram e 14 WARRANTY CERTIFICATE e e lm abm ale ae 16 APPLIANCE IDENTIFICATION PLATE 16 98102 US 5 2 03 2011 7 www santos fr awe CE COMPLIANCE DECLARATION THE MANUFACTURER SANTOS sas 140 150 Av Roger SALENGRO 69120 VAULX EN VELIN LYON FRANCE declares that the appliance intended for the professional market described below Description Grater Ice Crusher Type number 02 09 complies with e the statutory provisions defined in appendix 1 of the European machines directive n2006 42 CE and the national legislation transposing it e the statutory provisions of the following European directives and regulations o N 2006 95 CE low voltage directive N 2004 108 CE EMC directive No 2002 95 CE RoHS directive No 2002 96 CE WEEE directive N 1935 2004 CE regulation relating to materials and articles intended to come into contact with foodstuffs O O O E Harmonised European standards used to give presumption of conformity with the essen
6. R OVERLOAD SAFETY FEATURE Should the motor become blocked foreign body object that is too hard too much pressure with the lever on the products being processed the On Off switch 5 automatically trios to the 0 position Correct the problem and press the On Off switch 5 position 1 lf the problem persists switch off the power supply to the machine unplug the cord from the mains socket and call in the maintenance service or contact a SANTOS approved dealer MAINTENANCE Before carrying out any work on the appliance it must in all cases be unplugged from the mains power supply and the motor start capacitor discharged Discharging the capacitor Use a screwdriver with insulated handle to touch the 2 connectors on the capacitor 12 The appearance of an electric arc shows that the capacitor has discharged Spare parts IMPORTANT Use of spare parts other than certified original SANTOS parts is prohibited This machine requires no specific maintenance The bearings are lubricated for life lf work is required to replace worn parts such as start relay or the electric or other components refer to the parts list see exploded view at the end of the manual or which you can download from our website www santos fr 98102 US 5 2 03 2011 7 www santos fr awe For all spare part orders see references in the exploded view at the end of the manual state gt the type gt the machine serial number and
7. SANTOS SAS 140 150 AVENUE ROGER SALENGRO 69120 VAULX EN VELIN LYON FRANCE gt TEL 33 0 472 37 35 29 FAX 33 0 478 26 58 21 SANTOS E Mail santos santos fr WWW Santos fr GRATER N2 ICE CRUSHER N9 USER AND MAINTENANCE MANUAL IMPORTANT documents included in this manual to be kept e CE COMPLIANCE DECLARATION e WARRANTY CERTIFICATE Coffee grinders Fruit juicers Mixers Blenders Drinks dispensers Planetary mixers Cheese graters Ice crushers Mincers Vegetable slicers Dough mixer Moulins a cafe Presse fruits Mixers Blenders Distributeurs de boissons Batteurs melangeurs P trin Rapes a fromage Broyeurs gla ons Hache viande Coupe l gumes MODELES DEPOSES FRANCE ET INTERNATIONAL INTERNATIONALLY PATENTED MODELS 98102 US 5 2 03 2011 7 www santos fr Danos CONTENTS CE CONPLIANCEDECEARADION cercaran zer e diker el le dai 3 IMPORTANTSAFEGUARDS eren serena er ana ene ans er anna 4 IMPROPER A PANE Sa GE 4 ELECTRICAL SONNE E 4 USING FOR THE 1st TIME iii 5 RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE 5 JOSETTE 6 CN E E E 6 ICE gg aa a A Go ad 6 USING THE MACHINE een 7 SINE QUIS a a ee EE 7 Eet El ERR 7 TAKING APART left handed thread figure 3 7 R ASSENIB ENS EA sree aes e RA 7 ADJUSTING THE ICE CRUSHER figure 5 7 SAFE ACCESS TO THE TOOLS figure 6 7 MOTOR OVERLOAD SAF
8. UCT AT THE END OF ITS SERVICE LIFE This equipment is marked with the selective sorting symbol relating to wastes from electrical and electronic equipment It signifies that this product should be taken over by a selective collection system conforming to the Guideline 2002 96 EC WEEE part Professional Equipment so that it can be either recycled or dismantled in order to reduce any impact on the environment For more information please contact your Retailer or the SANTOS For eliminating or recycling components of equipment please contact a specialized company or contact SANTOS The electronic products not undergoing a selective sorting are potentially dangerous for the environment The damaging materials should be eliminated or recycled according to the regulations in force www santos fr 98102 US 5 2 03 2011 7 Bros INTRODUCTION Grater N2 e Solidly built cast aluminum and stainless steel sheet equipped with an unbreakable food quality plastic drawer grater No 2 is particularly suited for professional use Restaurants Pizzerias Cheese dairies Supermarkets Public Bodies e lt has a powerful motor and a high output stainless steel grating disc 110 mm in g the average delivery of grated cheese is 50 kg hr e Normally supplied with a disc with holes of 9 3 mm for Gruyere Grater no 2 can be used with other discs on request Disc with holes of 6 mm 02201DD Disc with holes of 8 mm 022
9. e Clamp the disc 6 and undo the screw 7 following the arrow clockwise with the closing key 14 REASSEMBLING figure 4 e Check that the key 8 is present on the motor shaft e Check that the seal 13 is present on the disc 6 e Place the disc on the motor shaft making the key match the key groove e Clamp the disc 6 and tighten the screw 7 following the arrow anti clockwise ADJUSTING THE ICE CRUSHER figure 5 t is possible to adjust the position of the knife on the ice crusher disc by loosening the 2 fastening screws 9 fixing the knife 10 onto its support 11 and by moving it to increase or to reduce the cutting height of the knife into the ice cube Tighten the 2 screws 9 carefully after adjusting SAFE ACCESS TO THE TOOLS figure 6 98102 US 5 2 03 2011 VN www santos fr The appliance can only start if the lever 4 is not extending out of the chute to insert the food 3 and if the drawer catching the food 1 is correctly placed on the slideway 2 Removing the drawer 1 causes the machine to stop Re starting the appliance requires specific operation of the On Off switch 5 again position 1 A cut in the mains power supply results in the On Off switch 5 stopping position 0 The fact of lifting the lever to add food into the chute 3 causes the motor to stop without causing the appliance to stop completely Lowering the lever 4 allows the motor to be restarted MOTO
10. ir of the defective products In case of revelation of an imperfection during the warranty period the Distributor has to unless a different written agreement of SANTOS indicate to his customer to stop any use of the defective product Such a use would release SANTOS of any responsibility APPLIANCE IDENTIFICATION PLATE SPECIMEN For all documents not supplied with the appliance I I Printed Faxed and Downloaded 98102 US 5 2 03 2011 www santos fr
11. k of maintenance or disrespect of elementary security electric rules It does not apply in case of regular wear and tear Any replacement of parts under warranty will be realized after return of the defective part in our workshops postage paid supported by a copy of a conformity statement on which appears the serial number of the appliance Every appliance is equipped with a descriptive plate conforming to the EC recommendations and of which a duplicate exists in the conformity statement serial number manufacturing date electrical characteristics In case of serious damage judged repairable only in our workshops and after prior consent from our departments any appliance under guarantee is sent by the Distributor carriage paid In case of repairs or reconditioning of appliances not under guarantee the round trip transport is payable by the distributor The parts and workforce are invoiced at the current rate A preliminary estimate can be supplied Coffee grinder not using SANTOS original burrs are not taken under guarantee The warranty conditions repairs reconditioning of the espresso coffee grinder are the object of a specific note Our guarantee does not extend to the payment of penalties the repair of direct or indirect damages and notably to any loss of income resulting from the nonconformity or the defectiveness of products SANTOS s global responsibility being limited to the sale price of the delivered product and to the possible repa
12. tial requirements of the above mentioned directives e NF EN 1678 A1 2010 Food processing machinery Vegetable cutting machines Safety and hygiene requirements This European standard is a type C standard as defined in EN ISO 12100 When the provisions of this type C standard differ from those stated in the type A or B standards the provisions of the type C standard override the provisions of the other standards This standard provides the means to comply with the requirements of the machines directive n 2006 42 CE see appendix ZA e NF EN ISO 12100 1 and 2 2004 Safety of machinery General principles for design e NF EN 60204 1 2006 Safety of machinery Electrical equipment of machines General requirements e NF EN 1672 2 2005 Food processing machinery Basic concepts Hygiene requirements Drawn up in VAULX EN VELIN on 01 01 2010 Signatory s position CHIEF EXECUTIVE OFFICER Signatory s name Aur lien FOUQUET Signature 98102 US 5 2 03 2011 www santos fr IMPORTANT SAFEGUARDS When using cleaning or maintaining the machine always follow these instructions Read all instructions Note You will find it easier to understand the next few paragraphs if you refer to the diagrams at the end of this manual IMPROPER USE 1 Do not place food in the channel and press with the plunger before you have started the machine 2 Neither a hose nor a pressure hose should be used for cleaning
13. urite H 4 3 Marron AAA levier ANA LJ 2 een Marron Noir Relais de 4 Lac Ja d marrage Marche Arr t E AL P1 S curit tiroir Blanc Blanc 1 Vert jaune 9 98102 US 5 2 03 2011 ay www santos fr Barros 7 TRANSLATION CHART FOR ELECTRICAL COMPONENTS Protecteur thermique Thermals cut out Relais de d marrage Starter rela Marche Arr t On Off Switch Micro Switch TRANSLATION CHART FOR WIRE COLORS VERT JAUNE GREEN YELLOW TRANSLATION CHART FOR COMPONENTS Re Designation 6 Complete disc S Kky Key o Fastening screw for the ice crusher knife Ice crusher knife Ice crusher knife support Capacitor Seal Closing key www santos fr 98102 US 5 2 03 2011 a WARRANTY CERTIFICATE WARRANTY Since the 01 01 95 all our appliances comply with CE and possess the CE label Our guarantee is of 24 months from the manufacturing date mentioned on the descriptive plate except concerning the asynchronous motors consisting of a rotor and a stator which are warranted for 5 years from their manufacturing date Warranty is strictly limited to the free replacement of any part of origin recognized by us as defective due to a defect or building default and identified as belonging to the concerned appliance Warranty does not apply to damages resulting from installation or use non complying with our appliance data sheet user s manual or in case of an evident lac
Download Pdf Manuals
Related Search