Home

Certificate LVD Test Report `VKO` ( PDF 10,37MB )

1. 1 03 02 2009 Date s of performance of tests 08 02 2009 05 02 2009 General remarks This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02 The test results presented in this report relate only to the object tested This report shall not be reproduced except in full without the written approval of the Issuing testing laboratory see Enclosure refers to additional information appended to the report see appended table refers to a table appended to the report Throughout this report a point is used as the decimal separator General product information The fans are designed for ventilation of domestic and similar purposes and for continuous operation Meaning of characters in type references VENTS xxx VKOy w z turbo VENTS trade mark xxx the diameter of the duct mm It can be 100 125 150 VKO indication of the series y can be blank k modified enclosure shape w can be blank 220 240 V or 12 V Z can be blank L long lasting bearing turbo can be blank turbo motor with increased power is installed Possible variants can be seen in table of model list on page 3 TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 5 of 67 Report No 282071
2. TUVRheinland Mell klet 2 Attachment 2 Jegyz k nyv sz m Test report No 28207138 001 Oldal Page 1 1 Probe M r eszk z Gy rt Lelt ri sz sz ria sz K v kalibr ci Measuring equipment Manufacturer Inventory Serial No Next calibration Dielectric strength tester Kikusui 211 23246 2005 2009 06 Ohm meter Ganz 2110 045 2009 09 Leakage current measurer HIOKI 2110 718 2010 06 Wattmeter Norma 211 570632 xx1 2005 2009 08 Hybrid recorder Yokogawa 2112 637 2010 08 EMF tester Narda 53298 2011 03 17 EMF tester Magnetic Field aga 53299 2011 03 17 Megjegyz s Remark F 27 X1 1 0 Page 1 1 2007 07 10 t l
3. ETN Certificate T VRheinland Ll d ud d wy of Conformity MEE according to Low Voltage Directive 2006 95 EC Certificate No M1 2992114 01 Report No 28207138 001 Certificate Holder VENTILATION SYSTEMS JSC 1 Mikhaila Kotzubinskiego str UA 01030 Kiev Ukraine Manufacturer VENTILATION SYSTEMS JSC 1 Mikhaila Kotzubinskiego str UA 01030 Kiev Ukraine Product Fans Identification VENTS xxx VKOy w z turbo Trademark VENTS xxx the diameter of the duct mm 100 125 150 VKO indication of the series y can be blank k modified enclosure shape w can ber Drank 220 240 V or 312 ve z can be blank L long lasting bearing turbo can be blank turbo motor with increased power is installed turbo motor with increased power can be blank Ratings AC 220 240V Class II 12V Class III IP x4 Name and adress of the factory Ventilation Systems JSC 36 40 Richchya Zhovtnya Str Boyarka 08150 Kiev Region Ukraine Tested according to EN 60335 2 80 2003 A1 EN 60335 1 2002 A1 A11 A12 A2 A13 EN 50366 2003 A1 This certificate refers to the above mentioned product This is to certify that the test sample is in conformity with the requirements of Annex of the Directive The holder of the certificate is entitled to use this certificate for the declaration of conformity according to Annex III of the Directive This certificate does not imply assessment of the production of the product an
4. 26 11 Replace Notes 1 and 2 by the following N A NOTE Conductors connected by soldering are not considered to be positioned or fixed so that reliance is not placed upon the soldering alone to maintain it in position unless they are held in place near the terminals independently of the solder A T VRheinland Page 10 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict 27 PROVISION FOR EARTHING 27 6 The printed conductors of printed circuit boards shall N A not be used to provide earthing continuity in hand held appliances They may be used to provide earthing continuity in other appliances if at least two tracks are used with independent soldering points and the appliance complies with 27 5 for each circuit 28 SCREWS AND CONNECTIONS Replace the penultimate row of Table 14 by the following gt 4 7 and 5 3 0 8 2 0 1 0 N A 28 3 Thread cutting self tapping screws and thread N A rolling screws shall only be used for electrical connections if they generate a full form standard machine screw thread However thread cutting self tapping screws shall not be used if they are likely to be operated by the user or installer Thread cutting thread rolling and space threaded N A screws may be used in connections providing earthing continuity provided it is not necessary to disturb the connection in normal use d
5. 800 1120 1260 NA 35000 and 26300 20 0 25 0 360 500 710 80 0 __ _ NA 55000 and lt 6300 20 01 25 0 360 50 0 630 7101 800 NA nse 50 0 720 100 0 126 0 142 0 160 0 N A 56300 and 8000 25 0 32 0 45 0 63 0 90 0 100 0 NA 6300and 8000 25 0 32 0 450 630 90 0 11000 NA 56300 and 8000 50 0 640 90 0 1260 160 0 180 0 2000 N A ETE 40 0 56 0 80 0 100 0 110 0 125 0 NA 58000 and 510000 32 0 40 0 560 800 1100 1250 NA gt 8000 and lt 10000 64 0 80 0 112 0 160 0 2000 2200 2500 NA 510000 and 12500 40 0 50 0 71 0 100 0 125 0 140 0 160 0 NA 510000 and 12500 40 0 50 0 71 0 100 0 125 0 140 0 160 0 NA 10000and 12500 80 0 100 0 142 0 200 0 2500 2800 3200 N A B Basic S Supplementary and R Reinforced 0 Between winding and motor body 9 between motor body and accessible part of enclosure 3 Between switch terminal and accessible part of enclosure Creepage distance mm Pollution degree TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 64 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict lt 50 02 06 08 1 8 P gt 50 and lt 125 0 3 0 7 1 0 2 2 N A gt 125and lt 250 04 10
6. IEC 60335 2 80 The temperature rise limits for fans marked with an P ambient operating temperature are reduced by the difference between the marked value and 25 C IEC 60335 2 80 13 LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING P TEMPERATURE 13 1 Leakage current not excessive and electric strength P adequate Heating appliances operated at 1 15 times rated N A power Init cc e rete ctr tete i Motor operated appliances and combined appliances 254 4V 1 06x240V P supplied at 1 06 times rated voltage 112 72 V 1 06x12 V Protective impedance and radio interference filters N A disconnected before carrying out the tests 13 2 Leakage current measured by means of the circuit P described in figure 4 of IEC 60990 Leakage current measurements See appended table P 13 3 The appliance is disconnected from the supply P Electric strength tests according to table 4 See appended table P No breakdown during the tests P 14 TRANSIENT OVERVOLTAGES N A Appliances withstand the transient overvoltages to N A which they may be subjected TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 12 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict Clearances having a value less than specified in Clearances are not less than N A table 16 subjected to an impulse voltage test the test specified voltage specified in table 6 No flashov
7. temperature rise exceeding the value specified for handles which are held for short periods only 22 14 No ragged or sharp edges creating a hazard for the Verified by visual inspection P user in normal use or during user maintenance No exposed pointed ends of self tapping screws etc P liable to be touched by the user in normal use or during user maintenance 22 15 Storage hooks and the like for flexible cords smooth N A and well rounded 22 16 Automatic cord reels cause no undue abrasion or No automatic cord reel N A damage to the sheath of the flexible cord no breakage of conductors strands no undue wear of contacts Cord reel tested with 6000 operations as specified N A Electric strength test of 16 3 voltage of 1000 V N A applied 22 17 Spacers not removable from the outside by hand or No spacers N A by means of a screwdriver or a spanner 22 18 Current carrying parts and other metal parts resistant P to corrosion under normal conditions of use 22 19 Driving belts not used as electrical insulation No driving belt N A 22 20 Direct contact between live parts and thermal Verified by visual inspection N A insulation effectively prevented unless material used is non corrosive non hygroscopic and non combustible Compliance is checked by inspection and if N A necessary by appropriate test 22 21 Wood cotton silk ordinary paper and fibrous or No such material P hygroscopic material not used as insulation unl
8. 19 1 Appliances subjected to tests of 19 101 19 102 and N A 19 103 19 101 Appliances supplied at rated voltage for 168 h the N A battery being continually charged 19 102 Short circuiting of the terminals of the battery being N A fully charged for appliances having batteries that can be removed without the aid of a tool TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 44 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 19 103 Appliances having batteries replaceable by the user N A supplied at rated voltage under normal operation with the battery removed or in any position allowed by the construction 21 101 Appliances having pins for insertion into socket N A outlets have adequate mechanical strength checked according to procedure 2 of IEC 68 2 32 Part of the appliance incorporating the pins subjected to the free fall test procedure 2 N A of IEC 60068 2 32 the number of falls being 100 the mass of part does not exceed 250 g N A 50 the mass of part exceeds 250 g N A After the test the requirements of 8 1 15 1 1 16 3 N A and clause 29 are met 22 3 Appliances having pins for insertion into socket N A outlets tested as fully assembled as possible 25 13 An additional lining or bushing not required for N A interconnection cords operating at safety extra low voltage 30 2 For parts of the appliance connected
9. 2 2 Appliances operated while attended parts of non N A metallic material supporting current carrying connections and parts of non metallic material within a distance of 3mm of such connections are subjected to the glow wire test of IEC 60695 2 1 1 The glow wire test is not carried out on parts of N A material classified as having a glow wire flammability index according to IEC 60695 2 12 of at least 750 C for connections carrying a current exceeding N A 0 5 A during normal operation 650 C for other connections N A Test as specified for an interposed shielding material N A When the glow wire test of IEC 60695 2 11 is carried N A out the temperatures are 750 C for connections carrying a current exceeding N A 0 5 A during normal operation 650 C for other connections N A Test not applicable to conditions as specified N A 30 2 3 Appliances operated while unattended tested as P specified in 30 2 3 1 and 30 2 3 2 Tests not applicable to conditions as specified N A A T VRheinland Page 13 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict 30 2 3 1 Parts of non metallic material supporting P connections that carry a current exceeding 0 2 A during normal operation and parts of non metallic material within a distance of 3 mm of such connections are subjected to the glow wire test of IEC 60695 2 11 with a test se
10. 56 80 10 125 NA gt 800 and lt 1000 48 80 11 2 160 20 0 220 250 N A 32 5 0 7 1 10 0 14 0 16 0 NA 32 50 71 10 0 140 160 NA 64 100 142 200 290 320 NA 42 63 90 125 18 0 20 0 NA 42 63 90 125 180 200 _ NA 84 12 180 250 36 0 400 NA 56 8 0 110 160 22 0 250 NA 56 80 110 160 220 250 NA 1600and 2000 11 2 16 0 220 320 440 500 NA 75 100 140 200 28 0 32 0 NA 52000 and lt 2500 7 5 10 0 140 200 25 0 280 320 _ NA ETT IK 20 0 280 400 500 560 640 N A TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 63 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark 2500and 3200 10 0 125 180 250 360 400 NA 32500 and lt 3200 10 0 12 5 18 0 250 36 0 400 NA 32500 and lt 3200 20 0 25 0 360 500 72 0 800 NA 33200 and lt 4000 1125 16 0 22 0 320 45 0 50 0 NA 33200 and lt 4000 125 16 0 220 320 450 500 NA 33200 and 54000 250 32 0 440 640 90 0 1000 NA 54000 and 65000 16 0 20 0 28 0 40 0 56 0 63 0 NA ETT M 20 0 280 40 0 560 630 NA gt 4000 and lt 5000 32 0 40 0 560
11. 57 and 87 supply cords have N A a T rating of 60 C IEC 60227 Types 52 and 53 supply cords have a T rating of 70 C IEC 60227 Types 56 and 57 supply cords have a T rating of 90 C 14 TRANSIENT OVERVOLTAGES The impulse test voltage has a no load wave shape N A corresponding to the 1 2 50 us standard impulse specified in IEC 61180 1 It is supplied from a generator having conventional impedance not exceeding 42 Q The impulse test voltage is applied three times for each polarity with intervals of at least 1s A T VRheinland Page 3 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict 16 LEAKAGE CURRENT AND ELECTRIC STRENGTH 16 3 Electric strength tests according to table 7 see appended table P accordance with IEC 61180 1 Note 2 The characteristics of the high voltage P source used for the test are described in Table 5 Delete the penultimate paragraph of the test P specification 19 ABNORMAL OPERATION 19 1 Appliances incorporating contactors or relays N A subjected to the test of 19 14 19 7 In the second paragraph replace IEC 60252 by N A IEC 60252 1 19 11 Replace the second and third paragraphs by the N A following Appliances incorporating an electronic circuit are subjected to the tests of 19 11 3 and 19 11 4 Appliances incorporating an electronic circuit that N A relies upon a programmable co
12. Instructions for safe use provided Sufficient details for installation supplied Type or model number of luminaries which may be installed for fans intended for this purpose IEC 60335 2 80 For partition fans if intended for mounting in outside walls or windows IEC 60335 2 80 For fans intended to be mounted at high level fan has to be installed so that the blades are more than 2 3 m above the floor or windows IEC 60335 2 80 For duct and partition fans precautions taken to avoid back flow of gases into the room IEC 60335 2 80 If the instructions state that the guard has to be removed for cleaning purposes the instructions shall state the substance of the following Ensure that the fan is switched off from the supply mains before removing guard IEC 60335 2 80 No partition fans User s Manual Safety requirements states the necessary warning No guard N A N A N A N A P P N A 7 12 2 7 12 3 7 12 4 Stationary appliances not fitted with means for disconnection from the supply mains having a contact separation in all poles that provide full disconnection under overvoltage category III the instructions state that means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules Insulation of the fixed wiring in contact with parts exceeding 50 K during clause 11 instructions stating that the fixed wiring must be protected Instructions for bui
13. N A soldering points and the appliance complies with requirements of 27 5 for each circuit the material of the printed circuit board complies N A with IEC 60249 2 4 or IEC 60249 2 5 28 SCREWS AND CONNECTIONS 28 1 Fixings electrical connections and connections providing earthing continuity withstand mechanical stresses Screws not of soft metal liable to creep such as zinc Only metal screws used P or aluminium Diameter of screws of insulating material min 3 mm N A Screws of insulating material not used for any N A electrical connection or connections providing earthing continuity TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 37 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict Screws used for electrical connections or P connections providing earthing continuity screw into metal Screws not of insulating material if their replacement N A by a metal screw can impair supplementary or reinforced insulation Type X attachment screws to be removed for N A replacement of supply cord or for user maintenance not of insulating material if their replacement by a metal screw can impair basic insulation For screws and nuts test as specified see appended table P 28 2 Electrical connections and connections providing Class II Class III appliances N A earthing continuity constructed so that contact pressure
14. No such fans N A IEC 60335 2 80 Load four times the mass of the fan is suspended N A from the body of the fan for 1 min IEC 60335 2 80 A torque of 1 Nm is then applied to the fixed body of N A the fan for 1 min The test is repeated with the torque applied the reverse direction IEC 60335 2 80 22 CONSTRUCTION P 22 1 Appliance marked with the first numeral of the IP N A System relevant requirements of IEC 60529 are fulfilled 22 2 Stationary appliance means to provide all pole disconnection from the supply P provided the following means being available a supply cord fitted with a plug N A a switch complying with 24 3 No switch with all pole N A disconnection a statement in the instruction sheet that a Statement in the User s P disconnection incorporated in the fixed wiring is to be Manual provided an appliance inlet No appliance inlet N A Singe pole switches and single pole protective N A devices for the disconnection of heating elements in single phase permanently connected class appliances connected in the phase conductor 22 3 Appliance provided with pins no undue strain on No pins N A socket outlets Applied torque not exceeding 0 25 Nm N A Pull force of 50N to each pin after the appliance has N A being placed in the heating cabinet when cooled to room temperature the pins are not displaced by more than 1mm TRF No IEC60335_2_80B_mod TRF originator KEMA www tuv com Page
15. POWER INPUT AND CURRENT The permissible deviations apply for both limits of the range for appliances marked with a rated voltage range having limits differing by more than 10 of the arithmetic mean value of the range Note 1 and 2 do not apply N A The permissible deviations apply for both limits of the range for appliances marked with a rated voltage range having limits differing by more than 10 96 of the arithmetic mean value of the range Test for an appliance with one or more rated voltage ranges N A N A A T VRheinland Page 2 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict 11 HEATING Table 3 P First entry Replace the terms class A class E class B class F and class H by the terms class 105 class 120 class 130 class 155 and class 180 Table 3 P Fifth entry Rubber polychloroprene or polyvinyl chloride insulation of internal and external wiring including supply cords without temperature rating or with a temperature rating not exceeding 75 C with temperature rating T where T exceeds 75 C Footnote N A The temperature rise limit of windings in transformers and inductors mounted on printed circuit boards is equal to the thermal class of the winding insulation reduced by 25 K provided the largest dimension of the winding does not exceed 5 mm in cross section or length j IEC 60245 Types 53
16. Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict For coatings used on printed circuits boards to N A protect the microenvironment Type A or to provide basic insulation Type B annex J applies The microenvironment is pollution degree 1 under N A Type A coating No creepage distance or clearance requirements N A under Type B coating 29 1 Clearances not less than the values specified in table P 16 taking into account the rated impulse voltage for the overvoltage categories of table 15 unless for basic insulation and functional insulation they N A comply with the implulse voltage test of clause 14 However if the construction is affected by wear N A distortion movement of the parts or during assembly the clearances for rated impulse voltages of 1500V and above are increased by 0 5 mm and the impulse voltage test is not applicable Impulse voltage test not applicable P when the microenvironment is pollution degree 3 P for basic insulation of class 0 and class 01 N A appliances Appliances are in overvoltage category II Considered P Clearances less than specified in table 16 not N A allowed for basic insulation of class 0 and class Ol appliances or if pollution degree 3 is applicable Compliance is checked by inspection and measurements as specified 29 1 1 Clearances of basic insulation withstand the P overvoltages taking into account the rated impulse voltage Clearance at
17. X attachment fitted with a N A flexible cord as described Appliances incorporating an appliance inlet tested N A with or without an connector whichever is most unfavourable Detachable parts removed N A Overfilling test with additional amount of E N A water over a period of 1 min l The appliance withstands the electric strength test of N A 16 3 No trace of water on insulation that can result in a N A reduction of clearances and creepage distances below values specified in clause 29 15 3 Appliances proof against humid conditions 48h 95 25 C Humidity test for 48 h in a humidity cabinet The appliance withstands the tests of clause 16 16 LEAKAGE CURRENT AND ELECTRIC STRENGTH 16 1 Leakage current not excessive and electric strength adequate TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 14 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict Protective impedance disconnected from live parts N A before carrying out the tests 16 2 Single phase appliances test voltage 1 06 times 254 4V 1 06x240V P rated voltage cceccecceccesceceeceeeececeeceeeeeeeeeseeeeeees 12 72 V 1 06x12 V Three phase appliances test voltage 1 06 times N A rated voltage divided by V3 Leakage current measurements See appended table 16 3 Electric
18. an earthed screen between the primary and secondary windings clearances of basic insulation on the secondary side not less than those specified in table 16 but using the next lower step for rated impulse voltage Circuits supplied with a voltage lower than rated voltage clearances of functional insulation based on the working voltage used as the rated voltage in table 15 Creepage distances not less than those appropriate for the working voltage taking into account the material group and the pollution degree Pollution degree 2 applies unless precautions taken to protect the insulation pollution degree 1 N A N A N A N A N A insulation subjected to conductive pollution pollution degree 3 29 2 1 Microenvironment is pollution degree 3 unless insulation is enclosed or located that it is unlikely to be exposed to pollution during normal use IEC 60335 2 80 Compliance is checked by inspection and measurements as specified Creepage distances of basic insulation not less than specified in table 17 TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 40 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict For pollution degree 1 creepage distance not less N A than the minimum specified for the clearance in table 16 if the clearance has been checked according to the test of clause 14
19. appliances to the water mains complying with IEC 61770 and supplied with the appliance Thermal cut outs in duct fans in order to comply with cl 19 are not self resetting IEC 60335 2 80 TRF No IEC60335 2 80B mod N A N A N A Approved thermal link P TRF originator KEMA A T VRheinland www tuv com Page 29 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 25 SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS P 25 1 Appliance not intended for permanent connection to fixed wiring means for connection N A to the supply supply cord fitted with a plug N A an appliance inlet having at least the same degree N A of protection against moisture as required for the appliance pins for insertion into socket outlets N A 25 2 Appliance not provided with more than one means of Only one supply connection P connection to the supply mains Stationary appliance for multiple supply may be N A provided with more than one means of connection provided electric strength test of 1250 V for 1 min between each means of connection causes no breakdown 25 3 Connection of supply conductors for appliance P intended to be permanently connected to fixed wiring possible after the appliance has been fixed to its support Appliance provided with a set of terminals for the N A connection of cables or fixed wiring cross sectional areas specified in 26 6 Appliance pr
20. burning not exceeding 15 s J ANNEX J NORMATIVE COATED PRINTED CIRCUIT BOARDS Testing of protective coatings of printed circuit boards N A carried out in accordance with IEC 60664 3 with the following modifications 5 7 Conditioning of the test specimens When production samples are used three samples N A of the printed circuit board are tested 5 7 1 Cold The test is carried out at 25 C N A 5 7 3 Rapid change of temperature Severity 1 is specified N A 5 9 Additional tests This subclause is not applicable N A Q ANNEX Q INFORMATIVE SEQUENCE OF TESTS FOR THE EVALUATION OF ELECTRONIC CIRCUITS Replace 19 10 by 19 10 and 19 14 in two places N A A T VRheinland Page 17 of 17 Report No Report No 28207138 001 Attachment 1 EN 60335 1 A12 Clause Requirement Test Result Remark Verdict 29 CLEARANCE CREEPAGE DISTANCES AND SOLID INSULATION 29 3 Replace the third dashed item by N A Assessment of thermal quality of the material combined with an electric strength test 29 3 71 If accessible reinforced insulation consist of a single P layer the thickness of this layer comply with Table Z1 EN 60335 1 A13 Clause Requirement Test Result Remark Verdict 24 COMPONENTS 24 1 7 Remote operation is via telecommunication network Telecommunication interface circuity EN 41003 and EN 60950 1 2006 subclause 6 3 N A www tuv com M r eszkoz lista Measuring equipment list
21. deformation as a result of an external force applied to the enclosure Software used in protective electronic circuits is software class B or C Appliances connected to the water mains withstand the water pressure expected in normal use No leakage from any part including any inlet water hose Not movable appliance No mercury Not adjustable Not like a toy No software No connection to the water N A N A N A N A N A N A N A N A 22 48 23 23 1 22 101 Appliances connected to the water mains constructed to prevent backsiphonage of non potable water Appliances having provision for attaching a luminaire incorporate appropriate terminals and internal wiring IEC 60335 2 80 INTERNAL WIRING Wireways smooth and free from sharp edges Wires protected against contact with burrs cooling fins etc Wire holes in metal well rounded or provided with bushings Wiring effectively prevented from coming into contact with moving parts TRF No IEC60335 2 80B mod No such parts fixed N A N A The internal wiring is properly N A TRF originator KEMA A T VRheinland www tuv com Page 26 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 23 2 Beads etc on live wires cannot change their position No beads N A and are not resting on sharp edges or corners Beads inside flexible metal conduits con
22. foil 500 No 125 VKO Live and motor surface 1250 No Motor surface and enclosure wrapped with foil 1750 No Live and enclosure wrapped with foil 3000 No 17 TABLE Overload protection temperature rise N A Temperature rise of part at 19 7 TABLE Abnormal operation locked rotor moving parts P TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 59 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict Artiblent t 9C oet cirea ern te tn ped Temperature of winding 19 13 TABLE Abnormal operation temperature rises de 125 VKOk 12 turbo enclosure Ez according to clause 30 1 125 VKO enclosure 29 according to clause 30 1 TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Report No 28207138 001 Page 60 of 67 IEC 60335 2 80 Clause Requirement Test Result Remark An asterisk indicates a mark which assures the agreed level of surveillance TABLE Components P Object part No Manufacturer Type model Technical data Standard Mark s of trademark conformity For 12 V appliances Terminal Simet 210LTA 12 380V 2 5mm T85 EN 60998 2 1 BBJ 2 5 Switch VLM S p A 200 AC 250V 2A EN 61058 1 IMQ T125 cord operated Motor Hua Ning YJ 5816 5816 AC 12 V 50Hz EN 60335 1 Tested in the equipment Thermal link Aupo E
23. length of four times of the duct diameter 400mm 11 3 Temperature rises other than of windings P determined by thermocouples Temperature rises of windings determined by P resistance method unless the windings makes it difficult to make the necessary N A connections 11 4 Heating appliances operated under normal operation No heating appliances N A at 1 15 times rated power input 11 5 Motor operated appliances operated under normal 254 4V 1 06x240V and 12 72 P operation at most unfavourable voltage between 0 94 V 1 06x12 V were the most and 1 06 times rated voltage unfavourable for each model TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 11 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 11 6 Combined appliances operated under normal N A operation at most unfavourable voltage between 0 94 and 1 06 times rated voltage f 11 7 Operation until steady conditions are established P IEC 60335 2 80 11 8 Temperature rises not exceeding values in table 3 See appended tables Sealing compound does not flow out Protective devices do not operate except components in protective electronic circuits tested for N A the number of cycles specified in 24 1 4 Fans for tropical climates Temperature limits are N A reduced by 15 K
24. of test results information comments Design of rating label of other models is identical to the above except for type designation voltage rated power and flow rate Summary of testing Tests were conducted on models 125 VKOk 12 turbo 125 VKO During the documentation check the English User s Manual was evaluated Manufacturer Ventilation Systems JSC 1 Mikhaila Kotzubinskiego St Kiev UA 01030 Ukraine Factory location 36 40 Richchya Zhovtnya Str Boyarka 08150 Kiev Region Ukraine The following standard amendments are added by MEEI in the Attachment 1 IEC 60335 1 2001 A2 2006 EN 60335 1 2002 A2 2006 EN 60335 1 2002 A12 2006 EN 60335 1 2002 A13 2008 Attachments 1 Standard amendments TRF 17 pages 2 Measuring equipment list This Test Report consists of two parts first part contains requirements of IEC 60335 2 80 2002 incl A1 2004 in conjunction with IEC 60335 1 2001 incl A1 2004 EN 60335 2 80 2003 incl A1 2004 in conjunction with EN 60335 1 2002 incl A11 2004 and A1 2004 and EN 50366 2003 A1 2006 second part 1 attachment contains requirements of IEC 60335 1 2001 A2 2006 EN 60335 1 2002 A2 2006 EN 60335 1 2002 A12 2006 EN 60335 1 2002 A13 2008 TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 3 of 67 Report No 28207138 001 Model list
25. or automatic controls in flexible cords are allowed for appliances not exceeding 25 W IEC 60335 2 80 No devices causing the protective device in the fixed wiring to operate in the event of a fault in the appliance No thermal cut outs that can be reset by soldering Switches intended for all pole disconnection of stationary appliances are directly connected to the supply terminals and having a contact separation in all poles providing full disconnection under overvoltage category III conditions Plugs and socket outlets for extra low voltage circuits and heating elements not interchangeable with plugs and socket outlets listed in IEC 60083 or IEC 60906 1 or with connectors and appliance inlets complying with the standard sheets of IEC 60320 1 Capacitors in auxiliary windings of motors marked with their rated voltage and capacitance and used accordingly Voltage across capacitors in series with a motor winding does not exceed 1 1 times rated voltage when the appliance is supplied at 1 1 times rated voltage under minimum load N A N A N A N A N A N A No such appliance or circuit N A No auxiliary windings N A N A 24 6 24 7 24 101 Working voltage of motors connected to the supply mains and having basic insulation that is inadequate for the rated voltage of the appliance not exceeding 42V In addition the motors are complying with the requirements of Annex I Hose sets for connection of
26. out consecutively 22 Construction N A 22 101 For class I appliances incorporating a motor supplied N A by a rectifier circuit the d c circuit being insulated from accessible parts of the appliance by double or reinforced insulation TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 49 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict Compliance checked by the tests specified for double N A and reinforced insulation J ANNEX J NORMATIVE N A COATED PRINTED CIRCUIT BOARDS Testing of protective coatings of printed circuit boards No coated PCB N A carried out in accordance with IEC 60664 3 with the following modifications 6 6 Climatic sequence N A When production samples are used three samples N A of the printed circuit board are tested 6 6 1 Cold N A The test is carried out at 25 C N A 6 6 3 Rapid change of temperature N A Severity 1 is specified N A 6 8 6 Partial discharge extinction voltage N A Type A coatings not subjected to a partial discharge N A test 6 9 Additional tests N A This subclause is not applicable N A K ANNEX K NORMATIVE P OVERVOLTAGE CATEGORIES The information on overvoltage categories is P extracted from IEC 60664 1 Overvoltage category is a numeral defining a P transient overvoltage condition Equipment of overvoltage category IV is for use at N A the origin of the instal
27. parts separated from live parts by basic insulation only Only possible to touch parts separated from live parts P by double or reinforced insulation TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 10 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict After the removal of detachable parts for the N A purposes of user maintenance the basic insulation of internal wiring may be touched provided that it is electrically equivalent to the insulation of cords complying with IEC 60227 or IEC 61245 IEC 60335 2 80 9 STARTING OF MOTOR OPERATED APPLIANCES N A Requirements and tests are specified in part 2 when N A necessary 10 POWER INPUT AND CURRENT 10 1 Power input at normal operating temperature rated See appended table voltage and normal operation not deviating from rated power input by more than shown in table 1 Shutters or similar devices are in open position N A IEC 60335 2 80 10 2 Current at normal operating temperature rated Rated current is not marked N A voltage and normal operation not deviating from rated current by more than shown in table 2 Shutters or similar devices are in open position N A IEC 60335 2 80 11 HEATING 11 1 No excessive temperatures in normal use 11 2 Placing and mounting of appliance as described On horizontal support with a duct with a
28. parts of components and accessible parts of the appliance NOTE 4 Unless otherwise specified the Approved components used P requirements of 30 2 of this standard apply to parts of non metallic material in components including parts of non metallic material supporting current carrying connections inside components Components that have been previously tested and P shown to comply with the resistance to fire requirements in the IEC standard for the relevant component need not be retested provided that the severity specified in the component standard is not less than the severity specified in 30 2 of this standard and unless the preselection alternative is used the test report for the component states whether it complied IEC standard for the relevant component with or without flame Flames existing for a cumulative time not exceeding 2 s during the test are ignored A T VRheinland Page 8 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict If the above two conditions are not satisfied the N A component is tested as part of the appliance There are two levels of severity specified for N A appliances for which 30 2 3 is applicable Components that have not been previously tested N A and shown to comply with the IEC standard for the relevant component are tested according to the requirements of 30 2 of this standard In the fi
29. technical data UM Rated Rated IP Fan type Classification voltage power protection VENTS 100 VKO 14W VENTS 100 VKOL 14W VENTS 100 VKO turbo 16W VENTS 100 VKOk 14W VENTS 100 VKOk L 14W VENTS 100 VKOk turbo 16W 220 240V VENTS 125 VKO Class 1 50Hz 16W VENTS 125 VKOL 16W VENTS 125 VKO turbo 22W VENTS 150 VKO 24W VENTS 150 VKOL 24W IPX4 VENTS 150 VKO turbo 30 W VENTS 100 VKO 12 14W VENTS 100 VKOk 12 14W VENTS 125 VKO 12 16 W VENTS 125 VKOk 12 16 W VENTS 150 VKO 12 Class III 12 V 50 24W VENTS 150 VKOk 12 Hz 24 W VENTS 100 VKO 12 turbo 16 W VENTS 100 VKOk 12 turbo 16 W VENTS 125 VKO 12 turbo 20 W VENTS 125 VKOk 12 turbo 20 W Models differ in model name rated power shape of enclosure and bearing TRF No IEC60335_2 80B_mod TRF originator KEMA A T VRheinland www tuv com Page 4 of 67 Report No 28207138 001 Test item particulars Do Classification of installation and use Class Il Class III Supply Connection eene Permanent connection supply cord is not provided Possible test case verdicts test case does not apply to the test object N A test object does meet the requirement P Pass test object does not meet the requirement F Fail Testing rre pedit repere Date of receipt of test item
30. the terminals of tubular sheathed N A heating elements may be reduced to 1mm if the microenvironment is pollution degree 1 Lacquered conductors of windings considered to be N A bare conductors 29 1 2 Clearances of supplementary insulation not less than P those specified for basic insulation in table 16 29 1 3 Clearances of reinforced insulation not less than P those specified for basic insulation in table 16 but using the next higher step for rated impulse voltage TRF No IEC60335 2 80B mod TRF originator KEMA www tuv com Page 39 of 67 Clause IEC 60335 2 80 Requirement Test A T VRheinland Report No 28207138 001 Result Remark Verdict 29 1 4 For functional insulation the values of table 16 are applicable unless the appliance complies with clause 19 with the functional insulation short circuited Lacquered conductors of windings considered to be bare conductors However clearances at crossover points are not measured Clearance between surfaces of PTC heating elements may be reduced to 1mm P N A N A N A N A 29 1 5 29 2 Appliances having higher working voltage than rated voltage the voltage used for determining clearances from table 16 is the sum of the rated impulse voltage and the difference between the peak value of the working voltage and the peak value of the rated voltage If the secondary winding of a step down transformer is earthed or if there is
31. 004 and A1 2004 EN 50366 2003 4 A1 2006 added by MEEI in attachment IEC 60335 1 2001 A2 2006 and EN 60335 1 2002 A2 2006 A12 2006 A13 2008 Test DIOGSdUte 5 secet CB Scheme Non standard test method N A Test Report Form No IEC60335 2 80B mod RE ONNO acce hene nares KEMA modified by Hungarian Institute for Testing and Certification of Electrical Equipment Kft MEEI Kft Member of the T V Rheinland group MaSIBE ERES Iur neret Dated 2005 06 Copyright 2004 IEC System for Conformity Testing and Certification of Electrical Equipment IECEE Geneva Switzerland All rights reserved This publication may be reproduced in whole or in part for non commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material IECEE takes no responsibility for and will not assume liability for damages resulting from the reader s interpretation of the reproduced material due to its placement and context Test item description Fans UH MEER sd esteem oett VENTS Model Type reference VENTS xxx VKOy w z turbo model list on page 3 REG tW ENTRA NITET 220 240 V Class II 12 V Class III IP X4 for details see model list on page 3 TRF No IEC60335 2 80B mod TRF originator KEMA EIT ITE TITEL IE I T A T VRheinland www tuv com Page 2 of 67 Report No 28207138 001 Copy of marking plate and summary
32. 1 4 3 2 P gt 250 and lt 400 08 16 22 5 0 N A 5400 and 500 10 20 28 6 3 N A 5500 and 800 18 32 45 10 0 N A gt 800 and lt 1000 24 40 5 6 12 5 N A gt 1000 and lt 1250 32 5 0 7 1 16 0 N A gt 1250 and lt 1600 42 6 3 9 0 20 0 N A 51600 and lt 2000 56 8 0 11 0 25 0 N A gt 2000 and lt 2500 7 5 10 0 14 0 32 0 N A 52500 and lt 3200 10 0 12 5 18 0 40 0 N A gt 3200 and lt 4000 12 5 16 0 22 0 50 0 N A 54000 and lt 5000 16 0 20 0 28 0 63 0 N A 55000 and lt 6300 20 0 25 0 36 0 80 0 N A 56300 and lt 8000 25 0 32 0 45 0 100 0 N A 58000 and 10000 32 0 40 0 56 0 125 0 N A 510000 and lt 12500 40 0 50 0 71 0 160 0 N A 30 1 TABLE Ball pressure P Part Test temperature C Impression diameter Allowed impression mm diameter mm 125 VKOk 12 turbo Enclosure 75 0 8 2 Thermoplastic material held in 80 1 0 2 place the motor Terminal 125 0 4 2 125 VKO Enclosure 75 0 8 2 Thermoplastic material held in 80 1 0 2 place the motor Terminal 125 0 4 2 TRF No IEC60335 2 80B mod TRF originator KEMA A TUVRheinland www tuv com Page 65 of 67 Report No 28207138 001 Pictures of the appliances 125 VKOk 12 turbo front 125 VKOk 12 turbo back A TUVRheinland www tuv com Page 66 of 67 Report No 28207138 001 Pictures of the appliances 125 VKOk 12 turbo motor 125 VKOk 12 turbo front insid
33. 21 of 67 Clause IEC 60335 2 80 Requirement Test A TUVRheinland Report No 28207138 001 Result Remark Verdict 22 4 Each pin subjected to a torque of 0 4Nm the pins are not rotating unless rotating does not impair compliance with the standard Appliance for heating liquids and appliance causing undue vibration not provided with pins for insertion into socket outlets No such appliance N A N A 22 5 22 6 22 7 22 8 No risk of electric shock when touching the pins of the plug the appliance being disconnected from the supply at the instant of voltage peak Electrical insulation not affected by condensing water or leaking liquid Electrical insulation of Class II appliances not affected in case of a hose rupture or seal leak Adequate safeguards against the risk of excessive pressure in appliances provided with steam producing devices Electrical connections not subject to pulling during cleaning of compartments to which access can be gained without the aid of a tool and that are likely to be cleaned in normal use No steam No such cleaning N A N A N A N A N A 22 9 22 10 22 11 Insulation internal wiring windings commutators and slip rings not exposed to oil grease or similar substances Adequate insulating properties of oil or grease to which insulation is exposed Not possible to reset voltage maintained non self resetting thermal cut o
34. 29 2 2 Creepage distances of supplementary insulation at P least as specified for basic insulation in table 17 29 2 3 Creepage distances of reinforced insulation at least P double as specified for basic insulation in table 17 29 2 4 Creepage distances of functional insulation not less P than specified in table 18 Creepage distances may be reduced if the appliance N A complies with clause 19 with the functional insulation short circuited 29 3 Supplementary and reinforced insulation having P adequate thickness or a sufficient number of layers to withstand the electrical stresses Compliance checked by P measurement in accordance with 29 3 1 or P an electric strength test in accordance with 29 3 2 N A or an assessment of the thermal quality of the material N A combined with an electric strength test in accordance with 29 3 3 29 3 1 Supplementary insulation having a thickness of at 1 6 mm P least 1 mm Reinforced insulation having a thickness of at least 2 2 1 mm P mm 29 3 2 Each layer of material withstand the electric strength N A test of 16 3 for supplementary insulation Supplementary insulation consisting of at least 2 N A layers Reinforced insulation consisting of at least 3 layers N A 29 3 3 The insulation is subjected to the dry heat test Bb of N A IEC 60068 2 2 followed by the electric strength test of 16 3 N A If the temperature rise during the tests of Clause 19 N A does not exceed the value specified in Table 3 the t
35. 38 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 5 GENERAL CONDITIONS FOR THE TESTS Tests performed according to cl 5 e g nature of supply sequence of testing etc 5 7 Fans to be used in tropical climates the tests of Not for tropical climates N A clause 10 11 and 13 are carried out at 40 C 2 C IEC 60335 2 80 Fans to be marked with ambient operating Test of Clause 10 11 and 13 P temperature the tests of clause 10 11 and 13 are are performed on the carried out at the marked value 2 C temperature of 45 C IEC 60335 2 80 6 CLASSIFICATION 6 1 Protection against electric shock Class II and III 12 V Class 0 0l WMG ML assai io iioi ect joe tuto etc see Group differences too 6 2 Protection against harmful ingress of water IP X4 Duct fans shall be at least IPX2 IEC 60335 2 80 See above 6 101 Classification to climatic conditions temperature For temperate climate climates tropical climates IEC 60335 2 80 7 MARKING AND INSTRUCTIONS P 7 1 Rated voltage or voltage range V 1220 240 V 12V P Nature of supply essen Rii P Rated frequency Hz ses 150 Hz P Rated power input W sssssss 14 16 20 22 24 30 W for P details see model list on page 3 Rated current A cecceccescesceececeeceeceeeeseeseeeeeeteees Rated power state
36. 80B mod TRF originator KEMA A T VRheinland www tuv com Page 15 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 19 3 Test of 19 2 repeated test voltage V power input of N A 1 24 times rated power input 19 4 Test conditions as in cl 11 any control limiting the N A temperature during tests of cl 11 short circuited 19 5 Test of 19 4 repeated on Class OI and appliances N A with tubular sheathed or embedded heating elements No short circuiting but one end of the element connected to the elements sheath The test repeated with reversed polarity and the other N A end of the heating element connected to the sheath The test is not carried out on appliances intended to N A be permanently connected to fixed wiring and on appliances where an all pole disconnection occurs during the test of 19 4 19 6 Appliances with PTC heating elements tested at No PTC N A rated voltage establishing steady conditions The working voltage of the PTC heating element is N A increased by 5 and the appliance is operated until steady conditions are re established The voltage is then increased in similar steps until 1 5 times working voltage or until the PTC heating element ruptures 19 7 Stalling test by locking the rotor if the locked rotor P torque is smaller than the full load torque or locking moving parts of other appliances Locked rotor motor c
37. A www tuv com Page 53 of 67 IEC 60335 2 80 A TUVRheinland Report No 28207138 001 Clause Requirement Test Result Remark Verdict H 11 12 7 1 For appliances using software class C having a N A single channel with self test and monitoring structure the manufacturer provides the measures necessary to address the fault errors in safety related segments and data H 11 12 8 Software fault error detection occurs before N A compliance with 19 13 of IEC 60335 1 is impaired H 11 12 8 1 Replace text N A H 11 12 13 Software and safety related hardware under its N A control initializes and terminates before compliance with 19 13 of IEC 60335 1 is impaired TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 54 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict CLASSIFICATION 6 1 Protection against electric shock Glass Il Il IM iai tti rh eter Class LL TI 7 MARKING AND INSTRUCTIONS 7 1 Rated voltage or voltage range V 1220 240 V 12V Single phase appliances 230 V covered Covered see previous line Multi phase appliances 400 V covered 25 SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS 25 6 Plugs fitted with only one flexible cord Supply cords of single phase portable appliances having a rated current not exceeding 16 A shall be fitted with a plug complyi
38. IEC 61000 4 11 19 11 4 7 The appliance is subjected to mains signals in N A accordance with IEC 61000 4 13 test level class 2 19 12 If the safety of the appliance for any of the fault N A conditions specified in 19 11 2 depends on the operation of a miniature fuse link complying with IEC 60127 the test is repeated measuring the current flowing through the fuse link measured current A rated current of the fuse link A 19 13 During the tests the appliance does not emit flames P molten metal poisonous or ignitable gas in hazardous amounts Temperature rises not exceeding the values shown see appended table P in table 9 Enclosures not deformed to such an extent that P compliance with cl 8 is impaired If the appliance can still be operated it complies with N A 20 2 Insulation other than of class III appliance withstand the electric strength test of 16 3 P the test voltage specified in table 4 basic insulatiori nee eee L N and motor surface 1000V P Live and surface 500 V 12 V supplementary insulation esse Motor surface and enclosure P wrapped into metal foil 1750V reinforced insulation eee eee L N and enclosure wrapped P into metal foil 3000V The appliance does not undergo a dangerous P malfunction and no failure of protective electronic circuits if the N A appliance is still operable Appliances tested with an e
39. Page 9 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict polychloroprene sheathed at least 60245 IEC 57 N A cross linked polyvinyl chloride sheathed at least N A 60245 IEC 87 Polyvinyl chloride sheathed N A Not used if they are likely to touch metal parts having a temperature rise exceeding 75K during the test of Clause 11 light polyvinyl chloride sheathed cord at least N A 60227 IEC 52 appliances not exceeding 3 kg ordinary polyvinyl chloride sheathed cord at least N A 60227 IEC 53 other appliances Heat resistant polyvinyl chloride sheathed N A Not used for type X attachment other than specially prepared cords Heat resistant light polyvinyl chloride sheathed cord N A at least 60227 IEC 56 appliances not exceeding 3 kg heat resistant polyvinyl chloride sheathed cord N A 60227 IEC 57 other appliances 26 TERMINALS FOR EXTERNAL CONDUCTORS 26 2 NOTE Conductors connected by soldering are not N A considered to be positioned or fixed so that reliance is not placed upon the soldering alone to maintain it in position unless they are held in place near the terminals independently of the solder In Table 13 replace the last two rows by the N A following gt 32 and x50 6 and 10 6 to 16 gt 50 and lt 63 10and16 10 to 25 26 3 Compliance checked by inspection and by the test of subclause 9 6 of IEC 60999 1
40. V rated A measured A dl Required dl etedi iniii epa e i iia 120944 1272 45 C Thermocouple locations AT K Max AT K 125 VKOk 12 turbo Terminal block 40 Supply cord of the motor Enclosure 125 VKO Terminal block According to clause 30 1 40 30 According to clause 30 1 Supply cord of the motor Enclosure TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 56 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict Note s With a rated maximum ambient temperature of 45 C the max temperature rise is calculated as follows Winding components Class B resistance method ATmax 95K 45 25 K 75K Surface of components Terminal block ATmax 60 45 25 K 40K Internal wire ATmax 50 45 25 K 30K TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 57 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict TABLE Heating test resistance method P Test voltage V sess pier e Ambient ee eee i Temperature rise of winding Insulation class 0L X IL EAE p TABLE Leakage current Heating appliances 1 15 x rated input Dg Motor operated and combined appliances 1 06 x
41. a flame persists longer than 2 s during the test N A parts above the connection as specified subjected to the needle flame test of annex E unless the material is classified as V 0 or V 1 according to N A IEC 60695 11 10 30 2 4 Base material of printed circuit boards subjected to N A needle flame test of annex E Test not applicable to conditions as specified N A 31 RESISTANCE TO RUSTING P Relevant ferrous parts adequately protected against P rusting 32 RADIATION TOXICITY AND SIMILAR HAZARDS N A Appliance does not emit harmful radiation N A Appliance does not present a toxic or similar hazard N A A ANNEX A INFORMATIVE N A ROUTINE TESTS Description of routine tests to be carried out by the N A manufacturer B ANNEX B NORMATIVE N A APPLIANCES POWERED BY RECHARGEABLE BATTERIES The following modifications to this standard are No batteries N A applicable for appliances powered by batteries that are recharged in the appliance This annex does not apply to battery chargers N A TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 43 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 3 1 9 Appliance operated under the following conditions N A the appliance supplied by its fully charged battery N A operated as specified in relevant part 2 the battery is charged the battery being initially N A discharged to such an extent that th
42. ances and creepage N A distances for functional insulation across full disconnection and micro disconnection as stated in table 24 ANNEX I NORMATIVE N A MOTORS HAVING BASIC INSULATION THAT IS INADEQUATE FOR THE RATED VOLTAGE OF THE APPLIANCE The following modifications to this standard are N A applicable for motors having basic insulation that is inadequate for the rated voltage of the appliance Protection against access to live parts N A 8 1 Metal parts of the motor are considered to be bare N A live parts 11 Heating N A 11 3 Temperature rise of the body of the motor is N A determined instead of the temperature rise of the windings 11 8 Temperature rise of the body of the motor where in N A contact with insulating material not exceeding values in table 3 for the relevant insulating material 16 Leakage current and electric strength N A 16 3 Insulation between live parts of the motor and its N A other metal parts not subjected to the test 19 Abnormal operation N A 19 1 The tests of 19 7 to 19 9 not carried out N A 19 101 Appliance operated at rated voltage with each of the following fault conditions N A short circuit of the terminals of the motor including N A any capacitor incorporated in the motor circuit short circuit of each diode of the rectifier N A open circuit of the supply to the motor N A open circuit of any parallel resistor the motor being N A in operation Only one fault simulated at a time the tests carried N A
43. anded conductor test 8 mm insulation removed N A No contact between live parts and accessible metal N A parts and for class II constructions between live parts and metal parts separated from accessible metal parts by supplementary insulation only 26 6 Terminals for type X attachment and for connection Terminal block is suitable for P to fixed wiring suitable for connection of conductors connection up to 2 5 mm with required cross sectional area according to rated current 3A table 13 rated current A nominal cross sectional area mis ied poeti loe a oce pa amt ne iae Terminals only suitable for a specially prepared cord N A 26 7 Terminals for type X attachment accessible after N A removal of a cover or part of the enclosure 26 8 Terminals for the connection to fixed wiring including P the earthing terminal located close to each other 26 9 Terminals of the pillar type constructed and located P as specified TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 35 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 26 10 Terminals with screw clamping and screwless N A terminals not used for flat twin tinsel cords unless conductors ends fitted with a device suitable for screw terminals Pull test of 5 N to the connection N A 26 11 For type Y and Z attachment soldered welded N A crimped and similar connections may b
44. apacitors open circuited or No motor capacitor N A short circuited if required Locked rotor capacitors open circuited one at a time N A Test repeated with capacitors short circuited one at a N A time if required Appliances with timer or programmer supplied with N A rated voltage for each of the tests for a period equal to the maximum period allowed Other appliances supplied with rated voltage for a P period as specified Separate controls are mounted on a dull black No such controls N A plywood board IEC 60335 2 80 Approximately 5096 of the area of each ventilation N A opening is blocked IEC 60335 2 80 Winding temperatures not exceeding values See appended table P specified in table 8 TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 16 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict Temperature of the dull black painted board for the No such controls N A separate control do not exceed 50K for appliance with T marking 65K for other appliances IEC 60335 2 80 19 8 Three phase motors operated at rated voltage with Single phase motors N A one phase disconnected 19 10 Series motor operated at 1 3 times rated voltage for No series motor N A Iu Tm During the test parts not being ejected from the N A appliance 19 11 Electronic circuits compliance checked by evaluation N A of the faul
45. ces separated from accessible metal parts by supplementary insulation unless complying with 2242 Capacitors not connected between the contacts of a thermal cut out Lamp holders used only for the connection of lamps TRF No IEC60335 2 80B mod Not hand held use Not hand held use N A N A N A N A N A N A N A N A N A TRF originator KEMA www tuv com Page 25 of 67 Clause IEC 60335 2 80 Requirement Test A TUVRheinland Report No 28207138 001 Result Remark Verdict 22 40 22 41 22 42 22 43 22 44 22 45 22 46 22 47 Motor operated appliances and combined appliances intended to be moved while in operation or having accessible moving parts fitted with a switch to control the motor The actuating member of the switch being easily visible and accessible No components other than lamps containing mercury Protective impedance consisting of at least two separate components Values specified in 8 1 4 not exceeded if any one of the components are short circuited or open circuited Appliances adjustable for different voltages accidental changing of the setting of the voltage unlikely to occur Appliances are not allowed to have an enclosure that is shaped and decorated so that the appliance is likely to be treated as a toy by children When air is used as reinforced insulation clearances not reduced below the values specified in 29 1 4 due to
46. ct contact with basic or reinforced insulation For class II constructions conductive liquids which are in contact with live parts not in direct contact with reinforced insulation No liquid N A N A N A N A N A 22 34 22 35 22 36 22 37 22 38 22 39 Shafts of operating knobs handles levers etc not live unless the shaft is not accessible when the part is removed Handles levers and knobs held or actuated in normal use not becoming live in the event of an insulation fault Such parts being of metal and their shafts or fixings are likely to become live in the event of an insulation fault they are either adequately covered by insulation material or their accessible parts are separated from their shafts or fixings by supplementary insulation This requirement does not apply to handles levers and knobs on stationary appliances other than those of electrical components provided they are either reliably connected to an earthing terminal or earthing contact or separated from live parts by earthed metal Handles continuously held in the hand in normal use are so constructed that when gripped as in normal use the operators hand is not likely to touch metal parts unless they are separated from live parts by double or reinforced insulation Capacitors in Class II appliances not connected to accessible metal parts unless complying with 22 42 Metal casings of capacitors in Class II applian
47. d N A Manufacturer s or responsible vendor s name VENTS P trademark or identification mark Model or type reference See copy of marking plate Symbol 5172 of IEC 60417 for Class II appliances See copy of marking plate IP number other than IPXO sss IP X4 See copy of marking plate Symbol IEC 60417 5036 for the enclosure of No water valve N A electrically operated water valves in external hose sets for connection of an appliance to the water mains TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 6 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict For tropical climates marked with letter T Not for tropical climates N A IEC 60335 2 80 Fans intended for operation in locations where the 45 C is marked as Tmax P local ambient temperature exceeds 40 C marked with ambient operating temperature IEC 60335 2 80 7 2 Warning for stationary appliances for multiple supply N A Warning placed in vicinity of terminal cover N A 7 8 Range of rated values marked with the lower and 220 240 V 12V P upper limits separated by a hyphen Different rated values marked with the values N A separated by an oblique stroke 7 4 Appliances adjustable for different rated voltages the Not adjustable N A voltage setting is clearly discernible 7 5 Appliances with more than one rate
48. d does not permit to use of a T V Rheinland or MEEI mark The certificate is valid up to 3 years provided that the test specifications and construction of the product remain unchanged during this period Budapest 2009 02 09 C The CE marking may be used if all relevant and effective EC Directives are AX T vRheinland TEST REPORT IEC 60335 2 80 Safety of household and similar electrical appliances Part 2 Particular requirements for fans Report Reference No 28207138 001 Compiled by signature Ferenc Horvat Approved by signature Zoltan Zs kai DOW OF 18806 osse mon 05 02 2009 Number of pages 67 pages of test report CB Testing Laboratory Hungarian Institute for Testing and Certification of Electrical 7 Equipment Ltd MEEI Kft Member of the T V Rheinland gro p 5 PROBS duce enr ER RT H 1132 Budapest V ci t 48 a b Hungary Testing location procedure CBTL X SMT TMP POEM iiia ia dar e RREUNV As above Applicant s name Ventilation Systems JSC C GEN SSS E Loses 1 Mikhaila Kotzubinskiego St Kiev UA 01030 Ukraine Test specification SIBndafd vesicae E A IEC 60335 2 80 2002 Second Edition incl A1 2004 in conjunction with IEC 60335 1 2001 Fourth Edition incl A1 2004 EN 60335 2 80 2003 incl A1 2004 in conjunction with EN 60335 1 2002 incl A11 2
49. d voltage or one N A or more rated voltage ranges marked with rated input or rated current for each rated voltage or range unless the power input is related to the mean value of the Difference is less than 10 P rated voltage range Relation between marking for upper and lower limits N A of rated power input or rated current and voltage is clear 7 6 Correct symbols used P 7 7 Connection diagram fixed to appliances to be N A connected to more than two supply conductors and appliances for multiple supply 7 8 Except for type Z attachment terminals for connection to the supply mains indicated P as follows marking of terminals exclusively for the neutral P conductor N marking of protective earthing terminals symbol Class II III N A 5019 of IEC 60417 marking not placed on removable parts P 7 9 Marking or placing of switches which may cause a No such switch N A hazard 7 10 Indications of switches on stationary appliances and N A controls on all appliances by use of figures letters or other visual means ssssssssseeeeeeeee b The figure 0 indicates only OFF position unless no N A confusion with the OFF position TRF No IEC60335 2 80B mod TRF originator KEMA www tuv com Page 7 of 67 Clause IEC 60335 2 80 Requirement Test A T VRheinland Report No 28207138 001 Result Remark Verdict 7 11 7 12 7 12 1 Indication for direction of adjustment of controls
50. dged 19 11 4 Appliances having a switch with an off position N A obtained by electronic disconnection or a switch that can be placed in the stand by mode N A subjected to the tests of 19 11 4 1 to 19 11 4 7 N A Appliances incorporating a protective electronic N A circuit subjected to the tests of 19 11 4 1 to 19 11 4 7 except that appliances operated for 30 s or 5 min during the test N A of 19 7 are not subjected to the tests for electromagnetic phenomena 19 11 4 1 The appliance is subjected to electrostatic discharges N A in accordance with IEC 61000 4 2 test level 4 19 11 4 2 The appliance is subjected to radiated fields in N A accordance with IEC 61000 4 3 test level 3 19 11 4 3 The appliance is subjected to fast transient bursts in N A accordance with IEC 61000 4 4 test level 3 or 4 as specified 19 11 4 4 The power supply terminals of the appliance N A subjected to voltage surges in accordance with IEC 61000 4 5 test level 3 or 4 as specified TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 18 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict Earthed heating elements in class appliances N A disconnected 19 11 4 5 The appliance is subjected to injected currents in N A accordance with IEC 61000 4 6 test level 3 19 11 4 6 The appliance is subjected to voltage dips and N A interruptions in accordance with
51. e A TUVRheinland www tuv com Page 67 of 67 Report No 28207138 001 Pictures of the appliances 100 VKOL nihil id 100 VKOk L Attachment 1 Clause A T VRheinland Page 1 of 17 IEC EN 60335 1 A2 GENERAL CONDITIONS FOR THE TESTS Tests performed according to cl 5 e g nature of supply sequence of testing etc The test of 19 14 is carried out before the tests of 19 11 MARKING AND INSTRUCTIONS Report No Report No 28207138 001 Requirement Test Result Remark Verdict 7 6 7 12 The power input is related to the arithmetic mean value of the rated voltage range Correct symbols used Instructions for safe use provided The instructions state that the appliance is not to be used by children or persons with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction PROTECTION AGAINST ACCESS TO LIVE PARTS Without appreciable force is considered to be a force not exceeding 1N Note 2 Without appreciable force is considered to be a force not exceeding 1N Note 2 Without appreciable force is considered to be a force not exceeding 1N Note1 for peak values over 15kV the energy in the discharge not exceeding 350 mJ N A N A 10 10 1 Note 1 does not apply Note Built in appliances and fixed appliances are tested after installation
52. e appliance cannot operate if possible the appliance is supplied from the supply N A mains through its battery charger the battery being initially discharged to such an extent that the appliance cannot operate The appliance is operated as specified in relevant part 2 If the appliance incorporates inductive coupling N A between two parts that are detachable from each other the appliance is supplied from the supply mains with the detachable part removed 3 6 2 Part to be removed in order to discard the battery is N A not considered to be detachable 5 101 Appliances supplied from the supply mains tested as N A specified for motor operated appliances 7 1 Battery compartment for batteries intended to be N A replaced by the user marked with battery voltage and polarity of the terminals 7 12 The instructions for appliances incorporating N A batteries intended to be replaced by the user includes required information Details about how to remove batteries containing N A materials hazardous to the environment given 7 15 Markings placed on the part of the appliance N A connected to the supply mains 8 2 Appliances having batteries that according to the N A instruction may be replaced by the user need only have basic insulation between live parts and the inner surface of the battery compartment If the appliance can be operated without batteries N A double or reinforced insulation required 11 7 The battery is charged for the period described N A
53. e used For Class II appliances the conductor so positioned N A or fixed that reliance is not placed on soldering welding or crimping alone For Class II appliances soldering welding or N A crimping alone used barriers provided clearances and creepage distances satisfactory if the conductor becomes free 27 PROVISION FOR EARTHING P 27 1 Accessible metal parts of Class 0l and I appliances N A permanently and reliably connected to an earthing terminal or contact of the appliance inlet Earthing terminals not connected to neutral terminal N A Class 0 II and III appliance have no provision for Class II III appliances no P earthing provision for earthing Safety extra low voltage circuits not earthed unless N A protective extra low voltage circuits 27 2 Clamping means adequately secured against N A accidental loosening Terminals used for the connection of external N A equipotential bonding conductors allow connection of conductors of 2 5 to 6 mm and do not provide earthing continuity between different N A parts of the appliance Conductors cannot be loosened without the aid of a N A tool 27 3 For detachable parts that are plugged into another N A part of the appliance and having an earth connection the earth connection made before and separated after current carrying connections when removing the part For appliances with supply cord current carrying N A conductors become taut before earthing conductor
54. eeding 3 kg ordinary polyvinyl chloride sheathed cord N A 60227 IEC 53 appliance exceeding 3 kg Temperature rise of external metal parts exceeding N A 75 K PVC cord not used unless appliance so constructed that the supply cord is not N A likely to touch external metal parts in normal use or the supply cord is appropriate for higher N A temperatures type Y or type Z attachment used 25 8 Nominal cross sectional area of supply cords Not provided N A according to table 11 rated current A cross sectional area mm sse 25 9 Supply cord not in contact with sharp points or edges N A 25 10 Green yellow core for earthing purposes in Class N A appliance 25 11 Conductors of supply cords not consolidated by lead N A tin soldering where they are subject to contact pressure unless clamping means so constructed that there is no risk N A of bad contacts due to cold flow of the solder 25 12 Moulding the cord to part of the enclosure does not N A damage the insulation of the supply cord 25 13 Inlet opening so shaped as to prevent damage to the P supply cord Unless the enclosure at the inlet opening is of N A insulation material a non detachable lining or bushing complying with 29 3 for supplementary insulation provided TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 31 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remar
55. environment Degrees of pollution in the microenvironment For evaluating creepage distances the following degrees of pollution in the microenvironment are established pollution degree 1 no pollution or only dry non N A conductive pollution occurs The pollution has no influence pollution degree 2 only non conductive pollution N A occurs except that occasionally a temporary conductivity caused by condensation is to be expected pollution degree 3 conductive pollution occurs or According clause 29 2 of P dry non conductive pollution occurs that becomes IEC 60335 2 80 conductive due to condensation that is to be expected pollution degree 4 the pollution generates N A persistent conductivity caused by conductive dust or by rain or snow N ANNEX N NORMATIVE N A PROOF TRACKING TEST TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 51 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict The proof tracking test is carried out in accordance N A with IEC 60112 with the following modifications 7 Test apparatus N A 7 3 Test solutions N A Test solution A is used N A 10 Determination of proof tracking index PTI N A 10 1 Procedure N A The proof voltage is 100 V 175 V 400 V or 600 V N A The last paragraph of Clause 3 applies N A The test is carried out on five specimens N A In case of doubt add
56. er during the test unless of functional N A insulation In case of flashover of functional insulation the N A appliance complies with clause 19 with the clearance short circuited 15 MOISTURE RESISTANCE 15 1 Enclosure provides the degree of moisture protection according to classification of the appliance Compliance checked as specified in 15 1 1 taking P into account 15 1 2 followed by the electric strength test of 16 3 No trace of water on insulation which can result in a P reduction of clearances and creepage distances below values specified in clause 29 15 1 1 Appliances other than IPXO subjected to tests as Tested for IP X4 P specified in IEC 60529 ss I Water valves in external hoses for connection of an N A appliance to the water mains tested as specified for IPX7 appliances Outer part of fans mounted in external structure of a N A building subjected to clause 14 2 4 a of IEC 60529 IEC 60335 2 80 Fans marked with the second numeral of the IP Tested for IP X4 P System are subjected to the appropriate of IEC 60529 both at rest and in operation while supplied at rated voltage IEC 60335 2 80 15 1 2 Hand held appliance turned continuously through the N A most unfavourable positions during the test Built in appliances installed according to the N A instructions Appliances placed or used on the floor or table N A placed on a horizontal unperforated support Appl
57. ess impregnated 22 22 Appliances not containing asbestos No asbestos P TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 23 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 22 23 Oils containing polychlorinated biphenyl PCB not P used 22 24 Bare heating elements adequately supported No heating elements N A In case of rupture the heating conductor is unlikely to N A come in contact with accessible metal parts 22 25 Sagging heating conductors cannot come into N A contact with accessible metal parts 22 26 The insulation between parts operating at safety No such parts N A extra low voltage and other live parts complies with the requirements for double or reinforced insulation 22 27 Parts connected by protective impedance separated No protective impedance N A by double or reinforced insulation 22 28 Metal parts of Class II appliances conductively N A connected to gas pipes or in contact with water separated from live parts by double or reinforced insulation 22 29 Class II appliances permanently connected to fixed Compliance is checked by P wiring so constructed that the required degree of visual inspection access to live parts is maintained after installation 22 30 Parts serving as supplementary or reinforced N A insulation fixed so that they cannot be removed without being seriously damaged or so constr
58. est of IEC 60068 2 2 is not carried out 30 RESISTANCE TO HEAT AND FIRE P TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 41 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 30 1 External parts of non metallic material parts supporting live parts and thermoplastic material providing supplementary or reinforced insulation sufficiently resistant to heat Ball pressure test according to IEC 60695 10 2 External parts at 40 C plus the maximum Enclosure tested on 75 C temperature rise determined during the test of clause 11 or at 75 C whichever is the higher emperaire C AE E EE EL E E pA M LM IDEEN Parts supporting live parts at 40 C plus the Terminal block tested on 125 C P maximum temperature rise determined during the test of clause 11 or at 125 C whichever is the higher temperature C sss Parts of thermoplastic material providing Thermoplastic material held in P supplementary or reinforced insulation 25 C plus the place the motor 80 C maximum temperature rise determined during GAUSS 19 if higher temperature C i 30 2 Relevant parts of non metallic material adequately P resistant to ignition and spread of fire 30 2 1 Glow wire test of IEC 60695 2 11 at 550 C unless Enclosure P the material is classified at least HB40 accordin
59. ew and old hose sets for N A appliances connected to the water mains by detachable hose sets 7 13 Instructions and other texts in an official language English and German provided P 7 14 Marking clearly legible and durable P 7 15 Marking on a main part P Marking clearly discernible from the outside if Marking label repeated inside P necessary after removal of a cover too For portable appliances cover can be removed or N A opened without a tool For stationary appliances name trademark or N A identification mark and model or type reference visible after installation For fixed appliances name trademark or P identification mark and model or type reference visible after installation according to the instructions Indications for switches and controls placed on or N A near the components Marking not on parts which can be positioned or repositioned in such a way that the marking is misleading 7 16 Marking of a possible replaceable thermal link or fuse Non replaceable thermal link N A link clearly visible with regard to replacing the link provided 8 PROTECTION AGAINST ACCESS TO LIVE PARTS P 8 1 Adequate protection against accidental contact with P live parts TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 9 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 8 1 1 Requirement applies for all positions detachable P parts removed Insertion or rem
60. f N A burning not exceeding 15 s F ANNEX F NORMATIVE N A CAPACITORS Capacitors likely to be permanently subjected to the N A supply voltage and used for radio interference suppression or voltage dividing comply with the following clauses of IEC 60384 14 with the following modifications 1 5 Terminology N A 1 5 3 Class X capacitors tested according to subclass X2 N A 1 5 4 This subclause is applicable N A 1 6 Marking N A Items a and b are applicable N A 3 4 Approval testing N A 3 4 3 2 Table II is applicable as described N A 4 1 Visual examination and check of dimensions N A This subclause is applicable N A 4 2 Electrical tests N A 4 2 1 This subclause is applicable N A 4 2 5 This subclause is applicable N A 4 2 5 2 Only table IX is applicable N A Values for test A apply N A TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 46 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict However for capacitors in heating appliances the N A values for test B or C apply 4 12 Damp heat steady state N A This subclause is applicable N A Only insulation resistance and voltage proof are N A checked 4 13 Impulse voltage N A This subclause is applicable N A 4 14 Endurance N A Subclauses 4 14 1 4 14 3 4 14 4 and 4 14 7 N A applicable 4 14 7 Only insulation resistance and voltage proof are N A checked Visual exami
61. g to N A IEC 60695 11 10 Parts for which the glow wire test cannot be carried N A out meet the requirements in SO9772 for category HBF material 30 2 3 Appliances operated while unattended tested as P specified in 30 2 3 1 and 30 2 3 2 Test not applicable to conditions as specified P 30 2 3 1 Parts of insulating material supporting connections 12V P carrying a current exceeding 0 2A during normal operation and parts of insulating material within a distance of 3mm N A having a glow wire flammability index of at least Approved components 12 V P 850 C according to IEC 60695 2 12 30 2 3 2 Parts of insulating material supporting current P carrying connections and parts of insulating material within a distance of 3mm N A subjected to glow wire test of IEC 60695 2 1 1 P TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 42 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict Test not carried out on material having a glow wire N A ignition temperature according to IEC 60695 2 13 as specified Glow wire test of IEC 60695 2 11 the temperature being P 775 C for connections carrying a current exceeding Approved components 12 V P 0 2A during normal operation 650 C for other connections Approved components P Parts that during the test produce a flame persisting N A longer than 2 s tested as specified If
62. ge for both the basic insulation and supplementary insulation is taken as the working voltage across the complete double insulation System It is not divided according to thickness and dielectric constant of the basic insulation and supplementary insulation 30 RESISTANCE TO HEAT AND FIRE 30 2 Parts of non metallic material adequately resistant to P ignition and spread of fire This requirement does not apply to decorative trims N A knobs and other parts unlikely to be ignited or to propagate flames that originate inside the appliance Compliance checked by the test of 30 2 1 P In addition attended appliances 30 2 2 applies unattended appliances 30 2 3 applies Appliances for remote operation 30 2 3 applies N A Base material of printed circuit board 30 2 4 applies N A The tests are carried out on parts of non metallic P material that have been removed from the appliance When the glow wire test is carried out the parts are placed in the same orientation as they would be in normal use A T VRheinland Page 12 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict 30 2 1 Glow wire test of IEC 60695 2 11 at 550 C unless P the material is classified at least HB40 according to IEC 60695 11 10 Parts for which the glow wire test cannot be carried N A out meet the requirements in ISO9772 for category HBF material 30
63. hen touching the pins of the plug the appliance being disconnected from the supply at the instant of voltage peak Delete the note N A 22 04 This requirement does not apply to magnesium N A oxide and mineral ceramic fibres used for the electrical insulation of heating elements Delete note 2 N A 22 32 Insulating material in which heating conductors are N A embedded is considered to be basic insulation and not reinforced insulation Delete Note 1 and renumber existing Note 2 as N A Note 22 35 Instead of first paragraph N A actuated in normal use shall not become live in the event of a failure of basic insulation If these handles levers and knobs are of metal and if their shafts or fixings are likely to become live in the event of a failure of basic insulation they shall be adequately covered by insulating material or their accessible parts shall be separated from their shafts or fixings by supplementary insulation 22 40 Unless the appliance can operate continuously N A automatically or remotely without giving rise to a hazard appliances for remote operation being fitted with a switch The actuating member of the switch being easily visible and accessible 22 44 Appliances shall not have an enclosure that is P shaped or decorated like a toy 22 49 For remote operation the duration of operation shall N A be set before the appliance can be started unless the appliance switches off automatically or can operate conti
64. how the relief from strain and the N A prevention of twisting are obtained they are suitable for different types of cord N A cord cannot touch the clamping screws of cord N A anchorage if these screws are accessible unless separated from accessible metal parts by supplementary insulation TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 32 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict the cord is not clamped by a metal screw which N A bears directly on the cord at least one part of the cord anchorage securely N A fixed to the appliance unless part of a specially prepared cord screws which have to be operated when replacing N A the cord do not fix any other component if applicable if labyrinths can be bypassed the test of 25 15 is N A nevertheless withstood for Class 0 Ol and appliances they are of N A insulating material or are provided with an insulating lining unless a failure of the insulation of the cord does not make accessible metal parts live for Class II appliances they are of insulating N A material or if of metal they are insulated from accessible metal parts by supplementary insulation 25 17 Adequate cord anchorages for type Y and Z N A attachment 25 18 Cord anchorages only accessible with the aid of a P tool or so constructed that the cord can only be fitted with N A the aid of a
65. iances normally fixed to a wall and appliances N A with pins for insertion into socket outlets are mounted on a wooden board For IPX3 appliances the base of wall mounted N A appliances is placed at the same level as the pivot axis of the oscillating tube TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 13 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict For IPX4 appliances the horizontal centre line of the P appliance is aligned with the pivot axis of the oscillating tube However for appliances normally used on the floor or N A table the movement is limited to two times 90 for a period of 5 min the support being placed at the level of the pivot axis of the oscillating tube Appliances normally fixed to a ceiling are mounted N A underneath a horizontal unperforated support the pivot axis of the oscillating tube located at the level of the underside of the support For IPX4 appliances the movement of the tube is P limited to two times 90 from the vertical for a period of 5 min Wall mounted appliances take into account the N A distance to the floor stated in the instructions Appliances with type X attachment fitted with a N A flexible cord as described Detachable parts tested as specified N A 15 2 Spillage of liquid does not affect the electrical No spillage in normal condition N A insulation Appliances with type
66. if the cord slips out of the cord anchorage TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 36 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 27 4 No risk of corrosion resulting from contact between N A metal of earthing terminal and other metal Adequate resistance to corrosion of coated or N A uncoated parts providing earthing continuity other than parts of a metal frame or enclosure Parts of steel providing earthing continuity provided at N A the essential areas with an electroplated coating thickness at least 5 um Adequate protection against rusting of parts of N A coated or uncoated steel only intended to provide or transmit contact pressure In case of aluminium alloys precautions taken to N A avoid risk of corrosion 27 5 Low resistance of connection between earthing N A terminal and earthed metal parts This requirement does not apply to connections N A providing earthing continuity in the protective extra low voltage circuit provided that clearances of basic insulation are based on the rated voltage of the appliance Resistance not exceeding 0 1 O at the specified low N A resistance test 27 6 The printed conductors of printed circuit boards not N A used to provide earthing continuity in hand held appliances They may be used in other appliances if N A at least two tracks are used with independent
67. ions as specified N A 32 RADIATION TOXICITY AND SIMILAR HAZARDS Appliance shall not emit harmful radiation present a toxic or similar hazard due to their operation in normal use Compliance is checked by the limits or tests specified in Part 2 However if no limits or tests are specified in Part 2 then the appliance is deemed to comply with the requirement without testing D ANNEX D NORMATIVE THERMAL MOTOR PROTECTORS Delete the note P E ANNEX E NORMATIVE NEEDLE FLAME TEST Needle flame test carried out in accordance with N A IEC 60695 11 5 with the following modifications 7 Severities The duration of application of the test flame is 30 s N A tis A T VRheinland Page 16 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict Test procedure 9 1 The specimen so arranged that the flame can be N A applied to a vertical or horizontal edge as shown in the examples of figure 1 9 2 The first paragraph does not apply N A If possible the flame is applied at least 10 mm from a N A corner 9 3 The test is carried out on one specimen N A If the specimen does not withstand the test the test N A may be repeated on two additional specimens both withstanding the test 11 Evaluation of test results The duration of burning not exceeding 30 s N A However for printed circuit boards the duration of N A
68. istances satisfactory if the conductor becomes free at the soldered joint TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 34 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 26 3 Terminals for type X attachment and for connection P to fixed wiring so constructed that the conductor is clamped between metal surfaces with sufficient contact pressure and without damaging the conductor Terminals for type X attachment and those for connection to fixed wiring so fixed that P when tightening or loosening the clamping means the terminal does not loosen internal wiring is not subjected to stress clearances and creepage distances are not reduced below the values in 29 Compliance checked by inspection and by the test of 0 28 P subclause 8 6 of IEC 60999 1 the torque applied being equal to two thirds of the torque specified Nominal diameter of thread mm screw category torque NM ssiri 26 4 Terminals for type X attachment except those with a P specially prepared cord and those for connection to fixed wiring no special preparation of conductors required and so constructed or placed that conductors prevented from slipping out 26 5 Terminals for type X attachment so located or N A shielded that if a wire of a stranded conductor escapes no risk of accidental connection to other parts that result in a hazard Str
69. itional test with proof voltage N A reduced by 25V the number of drops increased to 100 10 2 Report N A The report stating if the PTI value was based on a N A test using 100 drops with a test voltage of PTI 25 V O ANNEX O INFORMATIVE P SELECTION AND SEQUENCE OF THE TESTS OF CLAUSE 30 Description of tests for determination of resistance to P heat and fire P ANNEX P INFORMATIVE N A GUIDANCE FOR THE APPLICATION OF THIS STANDARD TO APPLIANCES USED IN WARM DAMP EQUABLE CLIMATES Modifications applicable for class 0 and 01 appliances having a rated voltage N A exceeding 150V intended to be used in countries having a warm damp equable climate and that are marked WDaE Modifications may also be applied to class 1 appliances having a rated voltage N A exceeding 150V intended to be used in countries having a warm damp equable climate and that are marked WDaE if liable to be connected to a supply mains that excludes the protective earthing conductor 5 General conditions for the tests N A 5 7 The ambient temperature for the tests of Clauses 11 N A and 13 is 40 7 7 Marking and instructions N A 7 1 The appliance marked with the letters WDaE N A TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 52 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 7 12 The instructions state that the appliance is to be N A su
70. k Verdict If unsheathed supply cord a similar additional N A bushing or lining is required unless the appliance is class 0 N A 25 14 Supply cords adequately protected against excessive N A flexing Flexing test N A applied force N sese Doe N A number of flexings eser N A The test does not result in N A short circuit between the conductors N A breakage of more than 10 of the strands of any N A conductor separation of the conductor from its terminal N A loosening of any cord guard N A damage within the meaning of the standard to the N A cord or the cord guard broken strands piercing the insulation and N A becoming accessible 25 15 Conductors of the supply cord relieved from strain Cord anchorage provided P twisting and abrasion by use of cord anchorage The cord cannot be pushed into the appliance to P such an extent that the cord or internal parts of the appliance can be damaged Pull and torque test of supply cord values shown in 30N 0 1 Nm P table 10 pull N torque not on automatic cord reel NM Max 2 mm displacement of the cord and conductors P not moved more than 1 mm in the terminals Creepage distances and clearances not reduced P below values specified in 29 1 25 16 Cord anchorages for type X attachments constructed and located so that N A replacement of the cord is easily possible N A itis clear
71. lation Equipment of overvoltage category III is equipment in N A fixed installations and for cases where the reliability and the availability of the equipment is subject to special requirements Equipment of overvoltage category II is energy According to the clause 29 1 P consuming equipment to be supplied from the fixed installation If such equipment is subjected to special N A requirements with regard to reliability and availability overvoltage category III applies TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 50 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict N A Equipment of overvoltage category is equipment for connection to circuits in which measures are taken to limit transient overvoltages to an appropriate low level L ANNEX L INFORMATIVE P GUIDANCE FOR THE MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES Sequences for the determination of clearances and P creepage distances M ANNEX M NORMATIVE P POLLUTION DEGREE The information on pollution degrees is extracted P from IEC 60664 1 Pollution The microenvironment determines the effect of pollution on the insulation taking into account the microenvironment Means may be provided to reduce pollution at the P insulation by effective enclosures or similar Minimum clearances specified where pollution may P be present in the micro
72. lectronic switch in the off N A position or in the stand by mode do not become operational 19 101 Fans incorporating shutters or similar that are N A operated automatically are supplied at rated voltage in the closed or open position whichever is more unfavourable IEC 60335 2 80 TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 19 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 20 STABILITY AND MECHANICAL HAZARDS P 20 1 Adequate stability Appliance shall be installed N A properly according to the User s Manual Tilting test through an angle of 10 appliance placed N A on an inclined plane horizontal plane appliance does not overturn Tilting test repeated on appliances with heating N A elements angle of inclination increased to 15 Possible heating test in overturned position N A temperature rise does not exceed values shown in table 9 Portable pedestal fans exceeding 1 7 m and No such fans N A exceeding 10 kg tested with a force of 40 N at 1 5 m IEC 60335 2 80 20 2 Moving parts adequately arranged or enclosed as to P provide protection against personal injury Protective enclosures guards and similar parts are P non detachable Adequate mechanical strength and fixing of P protective enclosures Self resetting thermal cut outs and overcurrent No such cut outs N A protective devices not causi
73. lectronics P7 AC 250V 2A EN 60691 VDE Ltd Ti150 C Motor Johnson SP 5812 12 V 50 Hz EN 60335 1 Tested in the 5816 5820 equipment Thermal link Matsushita 109 AC 250V 2A EN 60691 VDE T 150 C Electric actuator ELTEK 100331 12 V AC DC EN 60730 1 ENEC EN 60730 2 14 For 220 240 V appliances Terminal SIMET 210LTA12 380V 2 5 mm EN 60998 BBJ 2 5 Motor JOHNSON SP 5820 220 240 V 50 Hz EN 60335 1 VDE 20W Thermal link Matsushita N 109 AC 250 2 A 114 C EN 60691 VDE alternate Matsushita N 124 AC 250 2 A 130 C EN 60691 VDE alternate Matsushita N 126 AC 250 2 A 133 C EN 60691 VDE Motor JOHNSON SP 5816 5812 220 240 V 50 Hz EN 60335 1 VDE Thermal link Matsushita EYP2BN109 114 C EN 60691 VDE TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 61 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark 28 1 TABLE Threaded part torque test OP Threaded part identification Diameter of thread Column number Applied torque mm I II or III Nm Motor holder screw 3 8 II 1 2 Cable anchorage 2 7 II 0 4 29 1 TABLE Clearances P Overvoltage category II P Type of insulation Rated impulse Min cl Basic Functional Supplementary Reinforced Verdict Remark voltage V mm 330 0 5 N A 500 05 56 P 800 05 N A 1500 1 0 N A 2500 20 5 5 P between winding and motor body between mot
74. lt condition is not applied between the two circuits of an optocoupler e failure of triacs in the diode mode N A f failure of an integrated circuit N A TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 17 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 19 11 3 If the appliance incorporates a protective electronic No protective electronic circuit N A circuit which operates to ensure compliance with clause 19 the relevant test is repeated with a single fault simulated as indicated in a to f of 19 11 2 During and after each test the following is checked N A the temperature rise of the windings do not exceed N A the values specified in table 8 the appliance complies with the conditions specified N A in 19 13 any current flowing through protective impedance N A not exceeding the limits specified in 8 1 4 If a conductor of a printed board becomes open circuited the appliance is considered N A to have withstood the particular test provided all three of the following conditions are met the material of the printed circuit board withstands N A the burning test of annex E any loosened conductor does not reduce the N A clearances or creepage distances between live parts and accessible metal parts below the values specified in cl 29 the appliance withstands the tests of 19 11 2 with N A open circuited conductor bri
75. lt in appliances dimensions of space User s Manual Preparation to device operation states the necessary disconnection Duct fan N A dimensions and position of supporting means distances between parts and surrounding structure dimensions of ventilation openings and arrangement v VU v D v connection to supply mains and interconnection of separate components allow disconnection of the appliance after installation by accessible plug or a switch in the fixed wiring unless TRF No IEC60335 2 80B mod N A TRF originator KEMA A T VRheinland www tuv com Page 8 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict a switch complying with 24 3 N A 7 12 5 Replacement cord instructions type X attachment N A with a specially prepared cord Replacement cord instructions type Y attachment N A Replacement cord instructions type Z attachment N A 7 12 6 Caution in the instructions for heating appliances with No heating appliances N A a non self resetting thermal cut out 7 12 7 Instructions for fixed appliances stating how the P appliance is to be fixed 7 12 8 Instructions for appliances connected to the water mains N A max inlet water pressure Pa No water mains N A min inlet water pressure if necessary Pa Doe N A Instructions concerning n
76. mponent to function correctly subjected to the test of 19 11 4 8 In the existing third paragraph replace switch by P device in two places In the sixth paragraph replace all three by both N A and delete the last dashed item 19 11 2 g failure of an electronic power switching device in a N A partial turn on mode with loss of gate base control During this test winding temperatures shall not exceed the values given in 19 7 19 11 4 In the first paragraph replace switch by device in N A three places A T VRheinland Page 4 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict In the last paragraph replace arresters by N A protective devices 19 11 4 6 The appliance is subjected to the Class 3 voltage N A dips and interruptions in accordance with IEC 61000 4 11 19 11 4 8 The appliance is supplied at rated voltage and N A operated under normal operation After 60s the power supply is reduced to a level such that the appliance ceases to respond or a programmable component cease to operate The appliance continues to operate normally or N A requires a manual operation to restart 19 13 After the tests and when the appliance has cooled to approximately room temperature compliance with Clause 8 shall not be impaired and the appliance shall comply with 20 2 if it can still be operated After operation o
77. nation no visible damage N A 4 17 Passive flammability test N A This subclause is applicable N A 4 18 Active flammability test N A This subclause is applicable N A G ANNEX G NORMATIVE N A SAFETY ISOLATING TRANSFORMERS The following modifications to this standard are No transformers N A applicable for safety isolating transformers 7 Marking and instructions N A 7 1 Transformers for specific use marked with N A name trademark or identification mark of the N A manufacturer or responsible vendor model or type reference N A 17 Overload protection of transformers and associated circuits N A Fail safe transformers comply with subclause 15 5 of N A IEC 61558 1 22 Construction N A Subclauses 19 1 and 19 1 2 of IEC 61558 2 6 are N A applicable 29 Clearances creepage distances and solid insulation N A 29 1 29 2 The distances specified in items 2a 2c and 3 in table N A and 29 3 13 of IEC 61558 1 apply TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 47 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict H ANNEX H NORMATIVE N A SWITCHES Switches comply with the following clauses of IEC 61058 1 as modified N A The tests of IEC 61058 1 carried out under the N A conditions occurring in the appliance Before being tested switches are operated 20 times N A without load 8 Marking and documentation N A Switches are not requi
78. ng a hazard by unexpected reclosure Not possible to touch dangerous moving parts with P test probe 20 101 Fan blades other than those for mounting at high Blades are guarded after the P level shall be guarded unless installation according the IEC 60335 2 80 User s Manual by the duct 21 MECHANICAL STRENGTH 21 1 Appliance has adequate mechanical strength and is constructed as to withstand rough handling Checked by applying blows to the appliance in P accordance with test Ehb of IEC 60068 2 75 spring hammer test impact energy 0 5 J If necessary supplementary or reinforced insulation N A subjected to the electric strength test of 16 3 If necessary repetition of groups of three blows on a N A new sample TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 20 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 21 2 Accessible parts of solid insulation having strength to P prevent penetration by sharp implements The insulation is tested as specified unless N A the thickness of supplementary insulation is at least 1 P mm and reinforced insulation is at least 2 mm 21 101 Fan guards are subjected to a push and pull force of Blades are guarded after the P 20 N Dangerous moving parts are not accessible installation according the IEC 60335 2 80 User s Manual by the duct 21 102 Ceiling fans have adequate strength
79. ng with the following standard sheets of IEC 60083 1975 No power supply cord provided N A N A N A N A for Class I appliances Standard Sheet C2b C3B or C4 N A for Class II appliances Standard Sheet C5 or C6 25 7 Supply cord not lighter than N A N A ordinary polychloroprene sheathed flexible cord code designation 60245 IEC 57 N A When supply cords having high flexibility are used they shall not be lighter than rubber insulated and sheathed cord code designation 60245 IEC 86 rubber insulated crosslinked PVC sheathed cord code designation 60245 IEC 87 crosslinked PVC insulated and sheathed cord code designation 60245 IEC 88 N A N A N A N A ANNEX EMF The appliance operated in continuous mode TRF No IEC60335 2 80B mod The Tested product also complies to the requirements of EN 50366 2003 A1 2006 Limit acsi 100 VENTS 125 VKOk turbo Measured max 0 319 P TRF originator KEMA A T VRheinland www tuv com Page 55 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict TABLE Power input deviation Input deviation of at P rated W P measured Dp W Required dP Remark W W 125 VKOK 12 turbo 20 18 3 1 7 4 See below 125 VKO 16 15 1 3 2 See below See below See below Remark Value of deviations was measured at 12 V and 240
80. not transmitted through insulating material liable to shrink or distort unless shrinkage or distortion compensated This requirement does not apply to electrical N A connections in circuits carrying a current not exceeding 0 5A 28 3 Space threaded sheet metal screws only used for N A electrical connections if they clamp the parts together Thread cutting self tapping screws only used for N A electrical connections if they generate a full form standard machine screw threa Such screws not used if they are likely to be operated N A by the user or installer unless the thread is formed by a swaging action Thread cutting and space threaded screws may be N A used in connections providing earthing continuity provided unnecessary to disturb the connection and at least two screws are used for each connection 28 4 Screws and nuts that make mechanical connection Mechanical connection does N A secured against loosening if they also make electrical not serve electrical connection connections or connections providing earthing continuity Rivets for electrical connections or connections N A providing earthing continuity secured against loosening if subjected to torsion 29 CLEARANCES CREEPAGE DISTANCES AND SOLID INSULATION P Clearances creepage distances and solid insulation P withstand electrical stress TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 38 of 67
81. nuously without hazard 22 50 Controls incorporated in the appliance take priority N A over controls actuated by remote operation A T VRheinland Page 6 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict 22 51 A control on the appliance shall be manually adjusted N A to the setting for remote operation before the appliance can be operated in this mode There shall be a visual indication on the appliance showing that the appliance is adjusted for remote operation The manual setting and the visual indication of the remote mode are not necessary on appliances that can operate continuously or operate automatically or be operated remotely without giving rise to a hazard 22 52 Socket outlets on appliances accessible to the user N A in accordance with the socket outlet system used in the country in which the appliance is sold A T VRheinland Page 7 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict 24 COMPONENTS 24 1 NOTE 1 Compliance with the IEC standard for the P relevant component does not necessarily ensure compliance with the requirements of this standard NOTE 2 Motors are not required to comply with IEC P 60034 1 NOTE 3 Unless otherwise specified the P requirements of Clause 29 of this standard apply between live
82. or body and accessible part of enclosure 4 000 3 5 8 P between live and accessible part of enclosure 6000 6 0 N A 8000 85 N A 10000 11 5 N A TABLE Creepage distances basic supplementary and reinforced insulation P Working voltage Creepage distance mm Pollution degree Material group Material group II Ila IIIb I Illa IIlb B9 S R Verdict o 02 oe og 12 15 17 19 P lt 50 02 06 09 1 2 15 1 7 19 N A TRF No IEC60335 2 80B mod TRF originator KEMA www tuv com Page 62 of 67 IEC 60335 2 80 A TUVRheinland Report No 28207138 001 Clause Requirement Test Result Remark 04 12 18 24 zol 34 38 P s50and lt 125 03 08 1 1 15 aol 21 24 NA 03 o8 11 15 19 21 24 NA 06 16 22 30 42 48 NA 06 13 18 25 36 40 9 p o6 13 18 25 36 40 9 P 125 and lt 250 12 26 36 50 sal 72 80 1 2 Pp 10 20 28 ES 5 6 6 3 NA 10 20 28 40 56 63 1 NA 20 4o 56 80 1 2 126 NA s400and lt 500 13 25 36 50 63 71 80 NA 5400 and 500 13 25 36 5 0 7 1 80 N A 26 50 72 100 142 160 NA 18 32 45 63 80 90 100 _ _ NA 500 and lt 800 18 32 45 63 sol 90 100 NA 36 64 90 126 160 180 200 N A 24 4o 56 80 11 0 125 NA 24 4o
83. oval of lamps protection against N A contact with live parts of the lamp cap Use of test probe B of IEC 61032 no contact with live P parts 8 1 2 Use of test probe 13 of IEC 61032 through openings No contact P in class 0 appliances and class II appliances constructions no contact with live parts Test probe 13 also applied through openings in N A earthed metal enclosures having a non conductive coating no contact with live parts 8 1 3 For appliances other than class II use of test probe N A 41 of IEC 61032 no contact with live parts of visible glowing heating elements 8 1 4 Accessible part not considered live if P safety extra low a c voltage peak value not 12V P exceeding 42 4 V safety extra low d c voltage not exceeding 42 4 V N A or separated from live parts by protective N A impedance If protective impedance d c current not exceeding N A 2 mA and a c peak value not exceeding 0 7 mA N A for peak values over 42 4 V up to and including N A 450 V capacitance not exceeding 0 1 uF for peak values over 450 V up to and including N A 15 kV discharge not exceeding 45 uC 8 1 5 Live parts protected at least by basic insulation before installation or assembly P built in appliances N A fixed appliances P appliances delivered in separate units N A 8 2 Class II appliances and constructions constructed so P that there is adequate protection against accidental contact with basic insulation and metal
84. ovided with a set of terminals allowing P the connection of a flexible cord Appliance provided with a set of supply leads N A accommodated in a suitable compartment Appliance provided with a set of terminals and cable N A entries conduit entries knock outs or glands allowing connection of appropriate type of cable or conduit 25 4 Cable and conduit entries rated current of appliance P not exceeding 16 A dimension according to table 10 Introduction of conduit or cable does not reduce P clearances or creepage distances below values specified in 29 25 5 Method for assemble supply cord with the appliance P type X attachment N A type Y attachment N A type Z attachment is allowed for portable fans N A IEC 60335 2 80 TRF No IEC60335 2 80B mod TRF originator KEMA A TUVRheinland www tuv com Page 30 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict Type X attachment other than those with a specially N A prepared cord not used for flat twin tinsel cords 25 6 Plugs fitted with only one flexible cord N A 25 7 Supply cord not lighter than N A braided cord 60245 IEC 51 Not provided N A ordinary tough rubber sheathed cord N A 60245 IEC 53 ordinary polychloroprene sheathed flexible cord N A 60245 IEC 57 flat twin tinsel cord 60227 IEC 41 N A light polyvinyl chloride sheathed cord N A 60227 IEC 52 appliance not exc
85. pplied through a RCD having a rated residual operating current not exceeding 30 mA The instructions state that the appliance is N A considered to be suitable for use in countries having a warm damp equable climate but may also be used in other countries 11 Heating N A 11 8 The values of Table 3 are reduced by 15 K N A 13 Leakage current and electric strength at operating temperature N A 13 2 The leakage current for class appliances not N A exceeding 0 5 mA 15 Moisture resistance N A 15 3 The value of t is 37 C N A 16 Leakage current and electric strength N A 16 2 The leakage current for class appliances not N A exceeding 0 5 mA 19 Abnormal operation N A 19 13 The leakage current test of 16 2 is applied in addition N A to the electric strength test of 16 3 Q ANNEX Q INFORMATIVE N A SEQUENCE OF TESTS FOR THE EVALUATION OF ELECTRONIC CIRCUITS Description of tests for appliances incorporating electronic circuits N A R ANNEX R NORMATIVE N A SOFTWARE EVALUATION Software evaluated in accordance with the following clauses of Annex H of IEC 60730 N A 1 as modified H 2 Definitions N A Only definitions H 2 16 to H 2 20 applicable N A H 7 Information N A Only footnotes 12 to 18 of Table 7 2 as modified N A applicable H 11 12 Controls using software N A All the subclauses of H 11 12 as modified except N A H 11 12 6 and H 11 12 6 1 applicable H 11 12 7 Delete text NA TRF No IEC60335 2 80B mod TRF originator KEM
86. r interruption of a control clearances P and creepage distances across the functional insulation withstanding the electric strength test of 16 3 the test voltage being twice the working voltage Appliances tested with an electronic switch in the off position or in the stand by mode N A N A do not become operational or if they become operational do not result in a dangerous malfunction during or after the tests of 19 11 4 Note Unintended operation that may impair safety can result from careless use of appliances such as storage of small appliances while connected to the N A supply placing flammable material on working surfaces of heating appliances or N A placing objects in areas near motorized appliances N A that are not expected to start 19 14 Appliances operated under the conditions of Clause N A 11 Contactors or relays contacts operating under the conditions of clause 11 short circuited A T VRheinland Page 5 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict 22 CONSTRUCTION 22 2 Singe pole switches and single pole protective N A devices for the disconnection of heating elements in single phase permanently connected class 0l and class I appliances connected to the phase conductor 22 5 No risk of electric shock from charged capacitors N A having a rated capacitance exceeding 0 1 uF w
87. rated voltage 1 254 4V 12 72 V Leakage current between mA Max allowed I mA Live part and enclosure wrapped with foil 125 VKOk 12 turbo 0 01 0 5 TABLE Electric strength P Test voltage applied between Voltage V Breakdown Yes No 125 VKOk 12 turbo Live part and motor surface 500 No Live part and enclosure wrapped with foil 500 No 125 VKO Live part and motor surface 1000 No Motor surface and enclosure wrapped with foil 1750 No Live part and enclosure wrapped with foil 3000 No TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 58 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark TABLE Transient overvoltages Clearance between Required Rated impulse Impulse test Flashover CI mm voltage V voltage V Yes No 16 2 TABLE Leakage current P Single phase appliances 1 06 x rated voltage 254 4 V 12 72 V Three phase appliances 1 06 x rated voltage divided by V3 AR ET TS Leakage current between mA Max allowed I mA Live and enclosure wrapped with foil 125 VKOk 12 turbo 0 01 0 5 125 VKO 0 12 0 25 16 3 TABLE Electric strength P Test voltage applied between Voltage V Breakdown Yes No 125 VKOk 12 turbo Live and motor surface 500 No Live and enclosure wrapped with
88. rd except as specified If necessary electric strength test of 16 3 N A 25 24 Interconnection cords not detachable without the aid N A of a tool if compliance with the standard is impaired when they are disconnected 25 25 Dimensions of pins compatible with the dimensions N A of the relevant socket outlet Dimensions of pins and engagement face in accordance with the relevant plug in IEC 60083 26 TERMINALS FOR EXTERNAL CONDUCTORS 26 1 Appliances provided with terminals or equally Terminal block provided effective devices for connection of external conductors Terminals only accessible after removal of a non P detachable cover However earthing terminals may be accessible if a N A tool is required to make the connections and means are provided to clamp the wire independently from its connection 26 2 Appliances with type X attachment and appliances By screw P for connection to fixed wiring provided with terminals in which connections are made by means of screws nuts or similar devices unless the connections are soldered Screws and nuts serve only to clamp supply P conductors except internal conductors if so arranged that they are P unlikely to be displaced when fitting the supply conductors If soldered connections used the conductor so Soldered connection is not N A positioned or fixed that reliance is not placed on used soldering alone Soldering alone used barriers provided clearances N A and creepage d
89. red to be marked N A However switches that can be tested separately N A from the appliance marked with the manufacturer s name or trade mark and the type reference 13 Mechanism N A The tests may be carried out on a separate sample N A 15 Insulation resistance and dielectric strength N A 15 1 Not applicable N A 15 2 Not applicable N A 15 3 Applicable for full disconnection and micro N A disconnection 17 Endurance N A Compliance is checked on three separate appliances N A or switches For 17 2 4 4 the number of cycles is 10 000 unless N A otherwise specified in 24 1 3 of the relevant part 2 of IEC 60335 Switches for operation under no load and which can N A be operated only by a tool and switches operated by hand that are interlocked so that they cannot be operated under load are not subjected to the tests Subclauses 17 2 2 and 17 2 5 2 not applicable N A The ambient temperature during the test is that N A occurring in the appliance during the test of Clause 11 in IEC 60335 1 Temperature rise of the terminals not more than 30 K N A above the temperature rise measured in clause 11 of IEC 60335 1 20 Clearances creepage distances solid insulation and coatings of rigid printed board N A assemblies TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 48 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict This clause is applicable to clear
90. rst paragraph of the test specification replace P 24 1 1 to 24 1 6 by 24 1 1 to 24 1 9 Renumber Note 2 as Note 5 P Lampholders and starterholders not being tested and N A found to comply with the relevant IEC standard tested as a part of the appliance and additionally according to the gauging and interchangeability requirements of the relevant IEC standard NOTE 6 Where the relevant IEC standard specifies N A these gauging and interchangeability requirements at elevated temperatures the temperatures measured during the tests of Clause 11 are used 24 1 7 If the remote operation of the appliance is via a N A telecommunication network the relevant standard for the telecommunication interface circuitry in the appliance is IEC 62151 24 1 8 The relevant standard for thermal links is IEC 60691 P Thermal links not complying with IEC 60691 are considered to be an intentionally weak part for the purposes of Clause 19 24 1 9 Relays other than motor starting relays are tested N A as part of the appliance However they are also tested in accordance with Clause 17 of IEC 60730 1 under the maximum load conditions occurring in the appliance for at least the number of operations in 24 1 4 selected according to the relay function in the appliance 25 SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS 25 7 Supply cords being one of the following types rubber sheathed at least 60245 IEC 53 N A A T VRheinland
91. strength tests according to table 7 See appended table No breakdown during the tests 17 OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS N A No excessive temperatures in transformer or No transformers N A associated circuits in event of short circuits likely to occur in normal use Appliance supplied with 1 06 or 0 94 times rated N A voltage and the most unfavourable short circuit or overload likely to occur in normal use applied Temperature rise of insulation of the conductors of N A safety extra low voltage circuits not exceeding the relevant value specified in table 3 by more than 15 K Temperature of the winding not exceeding the value N A specified in table 8 however limits do not apply to fail safe transformers N A complying with sub clause 15 5 of IEC 61558 1 18 ENDURANCE N A Requirements and tests are specified in part 2 when Not applicable N A necessary 19 ABNORMAL OPERATION 19 1 The risk of fire or mechanical damage under abnormal or careless operation obviated Electronic circuits so designed and applied that a P fault will not render the appliance unsafe Fans incorporating shutters or similar subjected to See cl 19 101 N A the test of cl 19 101 IEC 60335 2 80 19 2 Test of appliance with heating elements with N A restricted heat dissipation test voltage V power input of 0 85 times rated power input TRF No IEC60335 2
92. sulation and sheath of internal wiring N A incorporated in external hoses for the connection of an appliance to the water mains at least equivalent to that of light polyvinyl chloride sheathed flexible cord 60227 IEC 52 24 COMPONENTS P 24 1 Components comply with safety requirements in P relevant IEC standards TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 27 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict List of components see appended table P Components not tested and found to comply with N A relevant IEC standard for the number of cycles specified are tested in accordance with 24 1 1 to 24 1 6 Components not tested and found to comply with N A relevant IEC standard components not marked or not used in accordance with its marking tested under the conditions occurring in the appliance 24 1 1 Capacitors likely to be permanently subjected to the N A supply voltage and used for radio interference suppression or for voltage dividing complying with IEC 60384 14 or tested according to annex F N A 24 1 2 Safety isolating transformers complying with IEC No transformers N A 61558 2 6 or tested according to annex G N A 24 1 8 Switches complying with IEC 61058 1 the number of N A cycles of operation being at least 10 000 or tested according to annex H N A If the switch operates a rela
93. t conditions specified in 19 11 2 for all circuits or parts of circuits unless they comply with the conditions specified in 19 11 1 Appliances incorporating a protective electronic N A circuit subjected to the tests of 19 11 3 and 19 11 4 Appliances having a switch with an off position N A obtained by electronic disconnection or a switch placing the appliance in a stand by mode subjected to the tests of 19 11 4 19 11 1 Before applying the fault conditions a to f in 19 11 2 it is checked if circuits or parts of N A circuit meet both of the following conditions the electronic circuit is a low power circuit that is N A the maximum power at low power points does not exceed 15 W according to the tests specified the protection against electric shock fire hazard N A mechanical hazard or dangerous malfunction in other parts of the appliance does not rely on the correct functioning of the electronic circuit 19 11 2 Fault conditions applied one at a time the appliance operated under conditions N A specified in cl 11 but supplied at rated voltage the duration of the tests as specified 8 short circuit of functional insulation if clearances or N A creepage distances are less than the values specified in 29 b open circuit at the terminals of any component N A C short circuit of capacitors unless they comply with N A IEC 60384 14 d short circuit of any two terminals of an electronic N A component other than integrated circuits This fau
94. t directly to the shielded material A T VRheinland Page 14 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict 30 2 3 2 Parts of non metallic material supporting current N A carrying connections and parts of non metallic material within a distance of 3 mm of such connections are subjected to the glow wire test of IEC 60695 2 11 However the glow wire test is not carried out on parts of material classified as having a glow wire ignition temperature according to IEC 60695 2 13 of at least 775 C for connections that carry a current exceeding 0 2 A during normal operation 675 C for other connections If the glow wire ignition temperature is not available N A for a sample with a thickness within 0 1 mm of the relevant part then the test sample shall have a thickness equal to the nearest preferred value specified in IEC 60695 2 13 that is no thicker than the relevant part NOTE 1 The preferred values in IEC 60695 2 13 N A are 0 75 mm 1 0 1 mm 1 5 mm 0 1 mm and 3 0 mm 1 0 2 mm Where an non metallic material is within 3 mm of a N A current carrying connection but is shielded from the connection by a different material the glow wire test of IEC 60695 2 11 is carried out at the relevant temperature with the tip of the glow wire applied to the interposed shielding material with the shielded material in place and no
95. t directly to the shielded material When the glow wire test of IEC 60695 2 11 is P carried out the temperatures are 750 C for connections that carry a current exceeding 0 2 A during normal operation 650 C for other connections NOTE 2 Contacts in components such as switch P contacts are considered to be connections NOTE 3 The tip of the glow wire is applied to the P part in the vicinity of the connection A T VRheinland Page 15 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict If parts that withstand the glow wire test of IEC N A 60695 2 11 but during the test produce a flame that persists for longer than 2 s then these parts and adjacent parts are further tested as follows Parts above the connection within the envelope of a vertical cylinder having a diameter of 20 mm and a height of 50 mm are subjected to the needle flame test of Annex E However parts shielded by a flame barrier that meets the needle flame test of Annex E are not tested The needle flame test is not carried out on parts of N A material classified as V 0 or V 1 according to IEC 60695 11 10 provided that the test sample used for the classification was no thicker than the relevant part of the appliance 30 2 4 Base material of printed circuit boards subjected to N A needle flame test of annex E Test is not applicable to condit
96. tained within N A an insulating sleeve 23 3 Electrical connections and internal conductors N A movable relatively to each other not exposed to undue stress Flexible metallic tubes not causing damage to No such parts N A insulation of conductors Open coil springs not used N A Adequate insulating lining provided inside a coiled N A Spring the turns of which touch one another No damage after 100 000 flexings for conductors N A flexed during normal use and at rated voltage IEC 60335 2 80 Electric strength test 1000 V between live parts and N A accessible metal parts 23 4 Bare internal wiring sufficiently rigid and fixed No bare internal wiring N A 23 5 The insulation of internal wiring withstanding the P electrical stress likely to occur in normal use No breakdown when a voltage of 2000 V is applied P for 15 min between the conductor and metal foil wrapped around the insulation 23 6 Sleeving used as supplementary insulation on N A internal wiring retained in position by positive means 23 7 The colour combination green yellow used only for Green yellow is not used in N A earthing conductors appliance 23 8 Aluminium wires not used for internal wiring No aluminium wire 23 9 No lead tin soldering of stranded conductors where No soldering for this reason they are subject to contact pressure unless clamping means so constructed that there is no risk N A of bad contact due to cold flow of the solder 23 10 The in
97. to the supply N A mains during the charging period 30 2 3 applies For other parts 30 2 2 applies N A C ANNEX C NORMATIVE N A AGEING TEST ON MOTORS Tests as described carried out when doubt with N A regard to the temperature classification of the insulation of a motor winding D ANNEX D NORMATIVE N A THERMAL MOTOR PROTECTORS Applicable to appliances having motors that N A incorporate thermal motor protectors E ANNEX E NORMATIVE N A NEEDLE FLAME TEST Needle flame test carried out in accordance with N A IEC 60695 2 2 with the following modifications 5 Severities N A The duration of application of the test flame is N A 30s t1s TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 45 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict 8 Test procedure N A 8 2 The specimen so arranged that the flame can be N A applied to a vertical or horizontal edge as shown in the examples of figure 1 8 4 The first paragraph does not apply N A If possible the flame is applied at least 10 mm froma N A corner 8 5 The test is carried out on one specimen N A If the specimen does not withstand the test the test N A may be repeated on two further specimens both withstanding the test 10 Evaluation of test results N A The duration of burning not exceeding 30 s N A However for printed circuit boards the duration o
98. tool 25 19 Type X attachment glands not used as cord N A anchorage in portable appliances Tying the cord into a knot or tying the cord with string N A not used 25 20 Conductors of the supply cord for type Y and Z N A attachment adequately additionally insulated 25 21 Space for supply cord for type X attachment or for P connection of fixed wiring constructed to permit checking of conductors with respect to correct positioning and connection before fitting any cover no risk of damage to the conductors when fitting the cover no contact with accessible metal parts if a conductor becomes loose etc For portable appliances the uninsulated end of a N A conductor prevented from any contact with accessible metal parts unless the end of the cord is such that the conductors are unlikely to slip free 25 22 Appliance inlet N A live parts not accessible during insertion or removal N A connector can be inserted without difficulty N A TRF No IEC60335 2 80B mod TRF originator KEMA A T VRheinland www tuv com Page 33 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict the appliance is not supported by the connector N A is not for cold conditions if temp rise of external N A metal parts exceeds 75 K unless the supply cord is not likely to touch such metal parts 25 23 Interconnection cords comply with the requirements No interconnection cord N A for the supply co
99. ucted that they cannot be replaced in an P incorrect position and so that if they are omitted the appliance is rendered inoperable or manifestly incomplete 22 31 Clearances and creepage distances over P supplementary and reinforced insulation not reduced below values specified in clause 29 as a result of wear Clearances and creepage distances between live P parts and accessible parts not reduced below values for supplementary insulation if wires screws etc become loose 22 32 Supplementary and reinforced insulation designed or P protected against deposition of dirt or dust Supplementary insulation of natural or synthetic N A rubber resistant to ageing or arranged and dimensioned so that creepage distances are not reduced below values specified in 29 2 Ceramic material not tightly sintered similar material N A or beads alone not used as supplementary or reinforced insulation TRF No IEC60335 2 80B mod TRF originator KEMA www tuv com Page 24 of 67 Clause IEC 60335 2 80 Requirement Test A TUVRheinland Report No 28207138 001 Result Remark Verdict 22 33 Oxygen bomb test at 70 C for 96 h and 16 h at room temperature Conductive liquids that are or may become accessible in normal use are not in direct contact with live parts Electrodes not used for heating liquids For class II constructions conductive liquids that are or may become accessible in normal use not in dire
100. uring user maintenance when replacing a supply cord having a type X attachment or during installation At least two screws must be used for each N A connection providing earthing continuity unless the screw forms a thread having a length of at least half the diameter of the screw 29 CLEARANCES CREEPAGE DISTANCES AND SOLID INSULATION If coatings are used on printed circuit boards to N A protect the microenvironment Type 1 coating or to provide basic insulation Type 2 coating Annex J applies The microenvironment is pollution degree 1 under Type 1 coating There are no clearance or creepage distance requirements under Type 2 coating N A 29 1 In Note 2 replace suppression by protective A T VRheinland Page 11 of 17 Report No Report No 28207138 001 Attachment 1 IEC EN 60335 1 A2 Clause Requirement Test Result Remark Verdict NOTE 6 For appliances intended for use at altitudes N A exceeding 2 000 m the altitude correction factors for clearances specified in Table A 2 of IEC 60664 1 should be taken into account 29 1 1 The values of Table 16 or the impulse voltage test of N A Clause 14 are applicable 29 2 NOTE 1 The working voltage for parts connected to N A the neutral is the same as for parts connected to the phase and this is the working voltage for basic insulation Add the following new note NOTE 6 In a double insulation system the working volta
101. uts by the operation of an automatic switching device incorporated within the appliance Non self resetting thermal motor protectors have a trip free action unless they are voltage maintained Location or protection of reset buttons of non self resetting controls is so that accidental resetting is unlikely Reliable fixing of non detachable parts that provide the necessary degree of protection against electric shock moisture or contact with moving parts Obvious locked position of snap in devices used for fixing such parts No deterioration of the fixing properties of snap in devices used in parts that are likely to be removed during installation or servicing TRF No IEC60335 2 80B mod No such kind of devices N A N A N A N A N A TRF originator KEMA A T VRheinland www tuv com Page 22 of 67 Report No 28207138 001 IEC 60335 2 80 Clause Requirement Test Result Remark Verdict Tests as described P 22 12 Handles knobs etc fixed in a reliable manner N A Fixing in wrong position of handles knobs etc N A indicating position of switches or similar components not possible Axial force 15 N applied to parts the shape being so N A that an axial pull is unlikely to be applied Axial force 30 N applied to parts the shape being so N A that an axial pull is likely to be applied 22 13 Unlikely that handles when gripped as in normal use N A make the operators hand touch parts having a
102. verity of 850 C However the glow wire test is not carried out on parts of material classified as having a glow wire flammability index of at least 850 C according to IEC 60695 2 12 If the glow wire flammability index is not available for a sample with a thickness within 0 1 mm of the relevant part then the test sample shall have a thickness equal to the nearest preferred value specified in IEC 60695 2 12 that is no thicker than the relevant part NOTE 1 The preferred values in IEC 60695 2 12 P are 0 75 mm 3 0 1 mm 1 5 mm 0 1 mm and 3 0 mm t 0 2 mm NOTE 2 Contacts in components such as switch P contacts are considered to be connections NOTE 3 The tip of the glow wire is applied to the P part in the vicinity of the connection The glow wire test is also not carried out on small N A parts that comply with the needle flame test of Annex E or on small parts of material classified as V 0 or V 1 according to IEC 60695 11 10 provided that the test sample used for the classification was no thicker than the relevant part of the appliance NOTE 4 Small parts are as defined in IEC 60695 4 N A Where a non metallic material is within 3 mm of a N A current carrying connection but is shielded from the connection by a different material the glow wire test of IEC 60695 2 11 is carried out at the relevant temperature with the tip of the glow wire applied to the interposed shielding material with the shielded material in place and no
103. y or contactor the N A complete switching system is subjected to the test 24 1 4 Automatic controls complying with IEC 60730 1 with relevant part 2 The number of N A cycles of operation being thermostats 10 000 N A temperature limiters 1 000 N A self resetting thermal cut outs 300 N A voltage maintained non self resetting N A thermal cut outs 1000 other non self resetting thermal cut outs 30 Thermal link used N A timers 3 000 N A energy regulators 10 000 N A Thermal motor protectors are tested in combination N A with their motor under the conditions specified in Annex D For water valves containing live parts and that are N A incorporated in external hoses for connection of an appliance to the water mains the degree of protection declared for subclause 6 5 2 of IEC 60730 2 8 is IPX7 TRF No IEC60335 2 80B mod TRF originator KEMA www tuv com Page 28 of 67 Clause IEC 60335 2 80 Requirement Test A TUVRheinland Report No 28207138 001 Result Remark Verdict 24 1 5 Appliance couplers complying with IEC 60320 1 No appliance coupler N A However appliances classified higher than IPXO the appliance couplers complying with IEC 60320 2 3 N A 24 1 6 24 2 24 3 24 4 24 5 Interconnection couplers complying with IEC 60320 2 2 Small lamp holders similar to E10 lampholders complying with IEC 60238 the requirements for E10 lampholders being applicable Switches

Certificate LVD Test Report `VKO` ( PDF 10,37MB )

Contents

Download Pdf Manuals

Related Search

Related Contents