CP5-Series User Manual
Contents
1. Problem Displayed weight fluctuates randomly Solution Make sure your workspace is stable and free of any air currents vibration and static electricity Nearby radio wave emitting devices can cause fluctuations Problem Displayed weight is inaccurate Solution Perform a calibration adjustment If you are still having trouble contact our warranty department IX Error Codes 1 OUTZ Zero point has drifted out of the acceptable range Try to perform a calibration adjustment If the problem persists the load cell may be permanently damaged due to overloading 2 O Ld Overload The maximum capacity has been exceeded Remove the extra weight to avoid permanently damaging the load cell 3 Lo Batteries are low Replace the batteries X Specifications 01015 K 010 CUBE 650 Max Capacity 100g 650g Readability 0 01g 0 1g Min Weight 0 03g 0 2g 2 x 1 5V AAA Alkaline Dimensions 3 1 x 3 1 x 0 7 in Platform Dimensions 3 1 x 3 1 in Warranty 10 Year Limited Warranty CUBE Manual XI Capacity Readability Charts 01011 00 CUBE 650 100g x 0 01g 650g x 0 1g 3 5270z x 0 0010z 22 920z x 0 010z 3 2150zt x 0 0010zt 20 89ozt x 0 010zt 64 30dwt x 0 01dwt 417 95dwt x 0 1dwt 500ct x 0 05ct 3250ct x 0 5ct 1543 2gn x 0 2gn 10031gn x 2gn 2 666tl x 0 001tI 13 333tl x 0 001tl American Weigh Scales Inc Norcross GA 30092 Made In Chi2. ALUS American Weigh Scales C BE User Manual CUBE 100 100g x 0 01g CUBE 650 650g x 0 1g Copyright 2014 American Weigh Scales Inc All rights reserved Rev 1 0 CUBE Manual Thank you for purchasing the American Weigh CUBE digital pocket scale Please read all operating instructions carefully before use Scales are precision measuring devices and should always be handled with proper care To ensure years of reliable service keep these simple tips in mind Do not exceed the scale s maximum capacity This scale has integrated overload protection but any overload protection has its limits Avoid exposure to extreme heat or cold Scales perform best at normal room temperature If temperatures have changed dramatically recalibration may be necessary Allow your scale to warm up for 30 60 seconds before performing calibration if available Store your scale in a clean dry location Dust dirt and moisture can accumulate on the weighing sensors and electronics causing inaccuracy or malfunction Avoid using your scale in close proximity to strong radio wave emitting devices such as cordless phones Always weigh on a flat and level surface free from vibrations and drafts The corner of a room is usually the most stable Gently apply all items to be weighed Do not drop items onto the weighing platform Avoid dropping your scale The warranty does not cover damage due to rough treatm
3. cale OFF press the I O key again V Changing the Unit of Measure 1 Press the M key to change the scales displayed unit of measure 2 If the scale is turned off then back on it will default to the last unit used CUBE 100 amp CUBE 650 Units g gram gn grain oz ounce ozt troy ounce ct carat tl tael dwt pennyweight VI Using the Tare Feature You can use this scale s tare feature to subtract the weight of an empty container or vessel for net weight determination NOTE The weight of the container will subtract from the available capacity subtractive taring 1 Place the empty container or vessel on the weighing platform 2 Tap the I O key briefly The display will then rese to zero after a couple seconds If the container is removed its weight will be displayed as a negative number 3 You may now fill the container with the quantity to be weighed The display will show the net weight of the contents 4 To return to normal weight display gross weight remove any items from the weighing platform and press the I O key again to re zero the scale VII Calibration Initial calibration is performed at the factory However the calibration can drift slightly due to stresses from shipping Also due to changes in local acceleration of gravity around the world adjustment is recommended when moving the scale from one location to another To check calibration 1 Place the require
4. d calibration weight on the scale and note the displayed value 2 If the displayed value is not within acceptable tolerance see chart on next page adjustment is required CUBE Manual Model Acceptable Calibration Recommended Tolerance Weight Accuracy Class CUBE 100 0 02g 100g OIML M2 CUBE 650 0 2g 500g OIML M2 Adjustment WARNING If you do not use the correct weight listed in the above chart for your scale you WILL miscalibrate and lose the factory calibration Calibration requires an accurate weight 1 Press and hold the M button to enter calibration mode The display will show the required weight 2 Make sure no weight is on the platform then tap the M key again to set the zero point The LCD will flash CAL followed by the required calibration weight again see chart above 3 Place the required weight on the center of the scale platform The display will flash PASS then return to normal weighing NOTE PASS only indicates that calibration has completed and is not a confirmation that you have used the correct weight 4 Test the accuracy by placing the same calibration weight back on the platform and checking the value If the value is within the acceptable tolerance limit above calibration is complete If not try repeating calibration under more stable conditions Vill Troubleshooting Problem Scale will not turn on Solution Check the batteries and battery contacts
5. ent or overload Check the batteries first if you are having any trouble with your scale This simple step can remedy most scale issues Calibration should be checked and adjusted occasionally as part of routine scale maintenance Part List 1 Scale 2 Hard Case Tray 3 AAA Batteries x2 I Key Description 1 M Tap to change weighing unit Hold to enter calibration see Section VII 2 I O Turns the scale on or off when platform is clear Zeros the weight of a container or tray if present lll Battery Installation oS C Proper Battery Orientation CUBE Manual Low batteries can cause inaccuracies in digital scales If you are experiencing issues with your scale first try new batteries Most times this will solve the problem 1 Before using the scale for the first time check the battery compartment and remove any plastic insulation strips or packaging that may be in place to prevent battery drainage during shipping storage 2 If you are replacing the batteries make sure the positive and negative contacts are properly aligned IV Operation 1 Place the scale on a flat level surface and press the 1O key to turn the scale on 2 Once the start up process completes and the scale goes to zero you are ready to weigh 3 Place the quantity to be weighed onto the weighing platform 4 Wait a couple seconds for the display to stabilize before taking a weight reading 5 To turn the s
6. na to our exact specifications and quality control
Download Pdf Manuals
Related Search