Lap Strap Fitting Instructions
Contents
1. fully removed from the slide bar end of the strap and pull out the end of from the buckle the strap from the buckle by feeding through the strap 17 The strap can now be removed from the other slide bar 294000 10056 Rev B Oxford Bathing Hoists Fitting Instructions Re assembling the lap strap When re assembling the components ensure that the strap is fed through the correct way on each part and that the strap is not twisted Failure to correctly re assemble the components to the strap may result in injury to the patient and or carer 18 Take one end of the strap and feed it 19 Feed the strap through the slide bar 20 Ensure that the strap is dressed correctly through the slide bar this photo shows the grip features on the slide bar mir i 21 Feed the strap through the buckle 22 Feed the strap on the return side of 23 Feed the strap back through the the buckle and pull through slide bar 4 ii i G 24 Pull the strap tight so that it is finished 25 Repeat the process 18 to 20 for 26 Feed the strap on the return side of off and securely fitted the other end of the strap Then the buckle and pull through Repeat feed the strap through the buckle the process 23 27 Pull the strap tight so that it is finished off and securely fitted 294000 10056 Rev B Oxford Fitting Instructions Bathing Hoists Operating Instructions It is recommended that the lap strap is securely atta2. is not twisted Failure to correctly re assemble the components to the strap may result in injury to the patient and or carer 20 Take one end of the strap and feed it 21 Feed the strap through the slide bar 22 Ensure that the strap is dressed correctly through the slide bar this photo shows the grip features on the slide bar mise i 23 Feed the strap through the buckle 24 Feed the strap on the return side of 25 Feed the strap back through the the buckle and pull through slide bar 26 Pull the strap tight so that it is finished 27 Repeat the process 20 to 22 for 28 Feed the strap on the return side of off and securely fitted the other end of the strap Then the buckle and pull through Repeat feed the strap through the buckle the process 25 29 Pull the strap tight so that it is finished off and securely fitted 294000 10055 Rev B Oxford Fitting Instructions Bathing Hoists Operating Instructions It is recommended that the lap strap is securely attached to the seat before the patient sits on the seat This will minimise the risk of a fall which could result in patient and or carer injury After the patient is transferred to the seat make sure that the patient is sitting upright in the middle of the seat Place the lap strap around the patient s waist and clip the male and female buckle together Check that the buckle has been securely clipped together The lap strap can be adjusted using th
3. uk e email info joerns co uk 294000 10055 Rev B Oxford Bathing Hoists Fitting Instructions Attaching the lap strap to the seat frame 1 The lap strap kit comprises of a strap 2 Take one end of the strap lift the 3 Bring the strap around to the top male and female buckle two slide bars plastic seat up from the frame and of the seat and two loop attachments Only one feed through the strap loop strap is required for this seat type 4 Wrap the strap around the back of the 5 Take the other end of the strap lift 6 Bring the strap around to the top metal framework as shown the plastic seat up from the frame of the seat and feed through the strap A 7 View of lap strap from underneath seat 8 Loosen the two bottom nuts holding 9 Slide the loop attachment between the backrest to the seat frame A the frame and backrest Ensure the 10mm spanner will be required orientation is correct to allow the press studs to be clipped together 4 10 Feed the strap through the loop 11 Retighten the two bottom nuts holding attachment and clip the press studs the backrest to the seat frame Ensure together Check that the attachment that the backrest is secure to the frame is secure to prevent injury to patient or carer Check that the lap strap is securely and correctly fitted Ensure that the strap is not twisted 294000 10055 Rev B Oxford Fitting Instructions Bathing Hoists Removal of t
4. Oxford Fitting Instructions Bathing Hoists Lap Strap Part No 750210J2 Suitable for use with all Mermaid Dipper and Ranger seat products Standard Seat for the Mermaid Fitting the lap strap to the Mermaid seat should be carried out by a competent person Intended Use The Mermaid product is intended to be used for both single and multiple patient use The term Single Patient Use refers to items that are used by an individual patient only throughout the course of treatment They should only be re used according to the recommendations outlined in the User Manual and must be kept in a clean condition stored appropriately and only be re used by the same patient The term Multiple Patient Use refers to items that are used by multiple patients throughout the course of treatment They should only be re used with a different patient after being cleaned according to the recommendations outlined in the User Manual and must always be kept in a clean condition and stored appropriately In all cases it is required that a clinical risk assessment should be carried out to verify that the patient has sufficient upper body strength to enable him her to maintain a steady position on the chair Also verifying that the patient has sufficient mental capacity to adhere to the caregivers instructions The assessment should be carried out by a qualified nurse or therapist before lifting patients with a Mermaid hoist A lap strap is fitted to
5. ched to the seat before the patient sits on the seat This will minimise the risk of a fall which could result in patient and or carer injury After the patient is transferred to the seat make sure that the patient is sitting upright in the middle of the seat Place the lap strap around the patient s waist and clip the male and female buckle together Check that the buckle has been securely clipped together The lap strap can be adjusted using the slide bars to meet the individual patient s needs and ensuring that the lap strap is tightened correctly For patient comfort the buckle should be positioned to one side refer to the photo 28 Sg BUCKLE gt am 28 Correct posture The gap between the lap strap and 29 Incorrect posture The patient is seating on the front the patient must not be sufficient to allow the patient of the seat laying back The patient could slip forward to slide out of position or off the seat and causing injury If you have any questions regarding the lap strap fitting please contact Oxford Customer Services on 44 0 844 811 1156 Joerns Healthcare Limited Drakes Broughton Business Park Worcester Road Drakes Broughton Pershore Worcestershire WR10 2AG UK T 44 0 844 8111156 F 44 0 844 811 1157 www joerns co uk e email info joerns co uk 294000 10056 Rev B
6. e slide bars to meet the individual patient s needs and ensuring that the lap strap is tightened correctly For patient comfort the buckle should be positioned to one side refer to the photo 30 BUCKLE 30 Correct posture The gap between the lap strap and 31 Incorrect posture The patient is seating on the front the patient must not be sufficient to allow the patient of the seat laying back The patient could slip forward to slide out of position or off the seat and causing injury If you have any questions regarding the lap strap fitting please contact Oxford Customer Services on 44 0 844 811 1156 Joerns Healthcare Limited Drakes Broughton Business Park Worcester Road Drakes Broughton Pershore Worcestershire WR10 2AG UK T 44 0 844 8111156 F 44 0 844 811 1157 www joerns co uk e email info joerns co uk 294000 10055 Rev B Oxford Fitting Instructions Bathing Hoists Lap Strap Part No 750210J2 Suitable for use with all Mermaid Dipper and Ranger seat products Ranger Seat for the Mermaid Fitting the lap strap to the Ranger seat should be carried out by a competent person Intended Use The Dipper product is intended to be used for both single and multiple patient use The term Single Patient Use refers to items that are used by an individual patient only throughout the course of treatment They should only be re used according to the recommendations outlined in the User Manual and mus
7. ean the lap strap The buckle can be cleaned either using a disinfectant spray or by immersing it in a suitable quantity of disinfectant solution in a suitable container The buckle can then be rinsed with clean water Dry both the buckle and strap with a disposable cloth Refit the lap strap to the product referring to the fitting instructions Joerns Healthcare Limited Drakes Broughton Business Park Worcester Road Drakes Broughton Pershore Worcestershire WR10 2AG UK T 44 0 844 8111156 F 44 0 844 811 1157 www joerns co uk e email info joerns co uk 294000 10056 Rev B Oxford Bathing Hoists Attaching the lap strap to the seat frame 2 Take one end of the strap lift the plastic seat up from the frame and feed through the strap Thelap strap kit comprises of a strap male and female buckle two slide bars and two loop attachments Only one loop strap is required for this seat type 4 Take the other end of the strap lift the plastic seat up from the frame and feed through the strap Wrap the strap around the back of the metal framework as shown Slide the loop attachment between the frame and plastic seat Lifting the plastic seat upwards will assist Ensure the orientation is correct to allow the press studs to be clipped together A 7 View of lap strap from underneath seat Take care not to catch your fingers when feeding through the loop attachment 294000 10056 R
8. etween the metal frame and plastic the opposite end appears as shown and two loop attachments seat 4 Wrap the strap around the back of the 5 Feed the buckle between the plastic 6 Loop the strap round the metal frame metal framework as shown seat and metal frame so that the buckle is at the front of the seat 7 Slide the loop attachment between the 8 Feed the strap through the loop 9 Repeat process 7 for the other frame and seat Ensure the orientation attachment and clip the press studs side of the seat frame is correct to allow the press studs to be together Check that the attachment clipped together is secure 10 Feed the strap through the loop attachment and clip the press studs together Check that the attachment is secure Check that the lap strap is securely and correctly fitted Ensure that the strap is not twisted 294000 10049 Rev B Oxford Fitting Instructions Bathing Hoists Removal of the lap strap for cleaning NOTE Refer to the section Care and Cleaning of the Lap Strap for recommended cleaning requirements For further cleaning recommendations refer to the User Manual supplied with the Mermaid Hoist Replacement User Manuals can be obtained by contacting Oxford Customer services on 44 0 844 811 1156 Please have details of your Mermaid Serial Number as this will be required 11 Unclip the press studs to open up both attachment loops and remove t
9. ev B Fitting Instructions 3 Bring the strap around to the top of the seat 6 Bring the strap around to the top of the seat 9 Feed the strap through the loop attachment and clip the press studs together Check that the attachment is secure A Check that the lap strap is securely and correctly fitted Ensure that the strap is not twisted Oxford Fitting Instructions Bathing Hoists Removal of the lap strap for cleaning NOTE Refer to the section Care and Cleaning of the Lap Strap for recommended cleaning requirements For further cleaning recommendations refer to the User Manual supplied with the Dipper Hoist Replacement User Manuals can be obtained by contacting Oxford Customer services on 44 0 844 811 1156 Please have details of your Mermaid Serial Number as this will be required 10 Unclip the press stud to open up the attachment loop and remove the lap strap by reversing the procedure taken to fit the lap strap to the seat frame If it is required to remove any of the components from the lap strap follow the instructions below ae A f 7 x aif 11 Feed out the strap and pull out the 12 Pull out the end of the strap from the 13 The strap can now be fully removed end of the strap from the slide bar buckle by feeding through the strap from the buckle Xe a hi 14 The strap can now be removed 15 Repeat the process 11 for the other 16 The strap can now be
10. he lap strap by reversing the procedure taken to fit the lap strap to the seat frame If it is required to remove any of the components from the lap strap follow the instructions below 13 Pull out the end of the strap from the 14 The strap can now be fully removed end of the strap from the slide bar buckle by feeding through the strap from the buckle Xe a hi 15 The strap can now be removed 16 Repeat the process 12 for the other 17 The strap can now be fully removed from the slide bar end of the strap and pull out the end of from the buckle the strap from the buckle by feeding through the strap 18 The strap can now be removed from the other slide bar 294000 10049 Rev B Oxford Bathing Hoists Fitting Instructions Re assembling the lap strap When re assembling the components ensure that the strap is fed through the correct way on each part and that the strap is not twisted Failure to correctly re assemble the components to the strap may result in injury to the patient and or carer 19 Take one end of the strap and feed it 20 Feed the strap through the slide bar 21 Ensure that the strap is dressed correctly through the slide bar this photo shows the grip features on the slide bar mir i 22 Feed the strap through the buckle 23 Feed the strap on the return side of 24 Feed the strap back through the the buckle and pull through slide bar 25 Pull the strap tight so tha
11. he lap strap for cleaning NOTE Refer to the section Care and Cleaning of the Lap Strap for recommended cleaning requirements For further cleaning recommendations refer to the User Manual supplied with the Mermaid Hoist Replacement User Manuals can be obtained by contacting Oxford Customer Services on 44 0 844 811 1156 Please have details of your Mermaid Serial Number as this will be required 12 Unclip the press stud to open up the attachment loop and remove the lap strap by reversing the procedure taken to fit the lap strap to the seat frame If it is required to remove any of the components from the lap strap follow the instructions below X f ES ai aA x FA 13 Feed out the strap and pull out the 14 Pull out the end of the strap from the 15 The strap can now be fully removed end of the strap from the slide bar buckle by feeding through the strap from the buckle hi 16 The strap can now be removed 17 Repeat the process 13 for the other 18 The strap can now be fully removed from the slide bar end of the strap and pull out the end of from the buckle the strap from the buckle by feeding through the strap aA 19 The strap can now be removed from the other slide bar 294000 10055 Rev B Oxford Bathing Hoists Fitting Instructions Re assembling the lap strap When re assembling the components ensure that the strap is fed through the correct way on each part and that the strap
12. ody strength to enable him her to maintain a steady position on the chair Also verifying that the patient has sufficient mental capacity to adhere to the caregivers instructions The assessment should be carried out by a qualified nurse or therapist before lifting patients with a Mermaid hoist A lap strap is fitted to the seat of the Mermaid Hoist to enable it to be used when required by the clinical risk assessment Before fitting the lap strap it should always be inspected If the lap strap is frayed worn or the buckle is damaged it should be disposed of immediately and replaced Care and Cleaning of the Lap Strap The lap strap is coated with a protective water proof PVC film and can be easily cleaned rinsed and reapplied to the seat The lap strap material can be cleaned using hard surface disinfectant wipes that are supplied impregnated with a 70 v v solution of Isopropyl Alcohol Thoroughly wipe clean the lap strap The buckle can be cleaned either using a disinfectant spray or by immersing it in a suitable quantity of disinfectant solution in a suitable container The buckle can then be rinsed with clean water Dry both the buckle and strap with a disposable cloth Refit the lap strap to the product referring to the fitting instructions Joerns Healthcare Limited Drakes Broughton Business Park Worcester Road Drakes Broughton Pershore Worcestershire WR10 2AG UK T 44 0 844 8111156 F 44 0 844 811 1157 www joerns co
13. p fitting please contact Oxford Customer Services on 44 0 844 811 1156 Joerns Healthcare Limited Drakes Broughton Business Park Worcester Road Drakes Broughton Pershore Worcestershire WR10 2AG UK T 44 0 844 8111156 F 44 0 844 811 1157 www joerns co uk e email info joerns co uk 294000 10049 Rev B Oxford Fitting Instructions Bathing Hoists Lap Strap Part No 750210J2 Suitable for use with all Mermaid Dipper and Ranger seat products Commode Seat for the Mermaid Fitting the lap strap to the Commode seat should be carried out by a competent person Intended Use The Mermaid product is intended to be used for both single and multiple patient use The term Single Patient Use refers to items that are used by an individual patient only throughout the course of treatment They should only be re used according to the recommendations outlined in the User Manual and must be kept in a clean condition stored appropriately and only be re used by the same patient The term Multiple Patient Use refers to items that are used by multiple patients throughout the course of treatment They should only be re used with a different patient after being cleaned according to the recommendations outlined in the User Manual and must always be kept in a clean condition and stored appropriately In all cases it is required that a clinical risk assessment should be carried out to verify that the patient has sufficient upper b
14. t be kept in a clean condition stored appropriately and only be re used by the same patient The term Multiple Patient Use refers to items that are used by multiple patients throughout the course of treatment They should only be re used with a different patient after being cleaned according to the recommendations outlined in the User Manual and must always be kept in a clean condition and stored appropriately In all cases it is required that a clinical risk assessment should be carried out to verify that the patient has sufficient upper body strength to enable him her to maintain a steady position on the chair Also verifying that the patient has sufficient mental capacity to adhere to the caregivers instructions The assessment should be carried out by a qualified nurse or therapist before lifting patients with a Dipper hoist A lap strap is fitted to the seat of the Dipper Hoist to enable it to be used when required by the clinical risk assessment Before fitting the lap strap it should always be inspected If the lap strap is frayed worn or the buckle is damaged it should be disposed of immediately and replaced Care and Cleaning of the Lap Strap The lap strap is coated with a protective water proof PVC film and can be easily cleaned rinsed and reapplied to the seat The lap strap material can be cleaned using hard surface disinfectant wipes that are supplied impregnated with a 70 v v solution of Isopropyl Alcohol Thoroughly wipe cl
15. t it is finished 26 Repeat the process 19 to 21 for 27 Feed the strap on the return side of off and securely fitted the other end of the strap Then the buckle and pull through Repeat feed the strap through the buckle the process 24 28 Pull the strap tight so that it is finished off and securely fitted 294000 10049 Rev B Oxford Fitting Instructions Bathing Hoists Operating Instructions It is recommended that the lap strap is securely attached to the seat before the patient sits on the seat This will minimise the risk of a fall which could result in patient and or carer injury After the patient is transferred to the seat make sure that the patient is sitting upright in the middle of the seat Place the lap strap around the patient s waist and clip the male and female buckle together Check that the buckle has been securely clipped together The lap strap can be adjusted using the slide bars to meet the individual patient s needs and ensuring that the lap strap is tightened correctly For patient comfort the buckle should be positioned to one side refer to the photo 29 BUCKLE 29 Correct posture The gap between the lap strap and 30 Incorrect posture The patient is seating on the front the patient must not be sufficient to allow the patient of the seat laying back The patient could slip forward to slide out of position or off the seat and causing injury If you have any questions regarding the lap stra
16. the seat of the Mermaid Hoist to enable it to be used when required by the clinical risk assessment Before fitting the lap strap it should always be inspected If the lap strap is frayed worn or the buckle is damaged it should be disposed of immediately and replaced Care and Cleaning of the Lap Strap The lap strap is coated with a protective water proof PVC film and can be easily cleaned rinsed and reapplied to the seat The lap strap material can be cleaned using hard surface disinfectant wipes that are supplied impregnated with a 70 v v solution of Isopropyl Alcohol Thoroughly wipe clean the lap strap The buckle can be cleaned either using a disinfectant spray or by immersing it in a suitable quantity of disinfectant solution in a suitable container The buckle can then be rinsed with clean water Dry both the buckle and strap with a disposable cloth Refit the lap strap to the product referring to the fitting instructions Joerns Healthcare Limited Drakes Broughton Business Park Worcester Road Drakes Broughton Pershore Worcestershire WR10 2AG UK T 44 0 844 8111156 F 44 0 844 811 1157 www joerns co uk e email info joerns co uk 294000 10049 Rev B Oxford Bathing Hoists Fitting Instructions Attaching the lap strap to the seat frame 1 The lap strap kit comprises of a strap 2 Take one end of the strap and feed it 3 Continue to feed the strap through until male and female buckle two slide bars b
Download Pdf Manuals
Related Search