English
Contents
1. 2 Limiter Droop Overall Shock Length 85mm Center to Center 3 Steering Ackerman Long lil Bump Steer Up Camber Link Position 1 V Shock Location Position 1 Outside gt Front Diff Fluid Grease Notes For increased stability use 10000 weight oil in the front and center differentials Center Diff Fluid Grease Toe3degres 3 3 3D h 9 J q eq Anti Squat 2degrees o Es Ride Height 25mm 2 5degrees Y Rear Hub Spacing All the way back oway Bar 1 8mm Piston Oil 4 holes 1 09mm 30 wt Spring Black Medium B re Limiter Droop en IT Overall Shock Length 100 8mm Center to Center Camber Link Position 2 A Shock Location Position 2 Inside Rear Diff Fluid Grease S 0 O Notes For increased traction use 2000 weight Motor Losi 3 4 oil in the rear differential ESC Battery Stock Gearing EX REAR EXPLODED VIEW HECK EXPLOSIONSZEICHNUNG VUE CLAT E ARRI RE VISTA ESPLOSA DELLA PARTE POSTERIORE FRONT EXPLODED VIEW FRONT EXPLOSIONSZEICHNUNG VUE ECLATEE AVANT VISTA ESPLOSA DELLA PARTE ANTERIORE A6290 CHASSIS EXPLODED2. NEN Not responsible for errors All prices subject to change without notice All instructions warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby Inc For up to date product literature visit www horizonhobby com and click on the support tab for this product Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product NOTICE Procedures which if not properly followed create a possibility of physical property damage AND a little or no possibility of injury CAUTION Procedures which if not properly followed create the probability of physical property damage AND a possibility of serious injury WARNING Procedures which if not properly followed create the probability of property damage collateral damage and serious injury OR create a high probability of superficial injury WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product personal property and cause serious injury This is a sophisticated hobby product and NOT a toy It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this Product in a safe and responsible manner could re
3. LOSB2962 LOSB4112 LOSB4113 HAJEN Front Shock Tower Machined Aluminum TEN Rear Shock Tower Machined Aluminum TEN Rear Shock Tower Carbon 4mm TEN Front Shock Tower Carbon 4mm TEN Rear Hubs Aluminum TEN Front Chassis Brace Aluminum TEN Rear Chassis Brace Aluminum TEN Shock Tops Aluminum 2 TEN One Piece Shock Standoffs TEN Shock Collars Aluminum 2 TEN Piston Pack 2 Ten T TEN SCTE Front and Rear Spring Set 4 Soft Silver 10 Front and Rear Spring Set 4 Firm Gold 10 T Adjustable Front Hinge Pin Holder Set TEN Adjustable Rear Hinge Pin Holder Set TEN SEZ 4 4E De TUP zl ecer Date 10 06 10 Event Track Track indoor Tight MSmooth M Hard Packed Blue Groove Wet Low Bite UHigh Bite Conditions Outdoor Open DRough Loose Loamy U Dry ODusty M Med Bite Other el 5 Ackerman Bump Steer Toe 1 deqrees OUT i Ride Height 29 5mm Camber _0 degree Caster Stock 20 degrees oway Bar 2 0mm Piston Oil 4 holes 1 07mm 40 wt Spring Gold Hard Up Down 3
4. Some fluid will bleed from around the bladder 10 Screw the shock cap onto the body until a little resistance is felt 11 Slowly push the shock shaft up This will allow excess fluid to bleed out 12 Tighten the cap all the way down using the shock tools included in your kit 13 Move the shock shaft up and down The shaft should be easy to push up into the body of the shock 14 Ifincreased pressure is felt towards the top there is too much oil in the shock Loosen the shock cap and bleed the shock as done in steps 11 and 12 15 Make sure each pair front rear of shocks has the same rebound and compression This is checked by holding one shock in each hand horizontally and pushing them together by the shock end Watch carefully to ensure that both compress evenly Now release both shocks and again watch carefully as they should rebound the same 2557 Warranty and Repair Policy Warranty Period L Exclusive Warranty Horizon Hobby Inc Horizon warranties that the Products purchased the Product will be free from defects in materials and workmanship at the date of purchase by the Purchaser imited Warranty Horizon reserves the right to change or modify this warranty without notice and disclaims all ot er warranties express or implied a This warranty is limited to the original Purchaser Purchaser and is not transferable REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EX
5. The TEN SCTE has three mounting locations on the front shock tower The position can be easily adjusted by simply moving the top of the shock to another hole The standard location works best on most surfaces Moving the top of the shock inward a hole will slow steering response and make the TEN SCTE smoother in bumps The standard position on the arm is middle which offers the best balance Running the inside shock location will give the TEN SCTE more steering into the turn and less steering on corner exit Running the shock location outside on the front arm will give you less overall steering into the turn and keep the front end flatter through the turn making the TEN SCTE smoother and easier to drive This can be used on high traction surfaces Keep in mind as you move the shocks in on the arm this will require internal limiters to obtain the correct suspension travel For the inside location a total of 200 inch limiter works great Losi sells a shock spacer set LOSA5050 that includes 030 inch 060 inch 090 inch and 120 inch spacers All of the Camber and Steering linkages feature left and right hand threads at either end like a turnbuckle to make adjustments easy The side with right hand threads has a small groove machined into it Use the plastic turnbuckle wrench supplied with the TEN SCTE to adjust these Using the right hand threaded side as your reference if you turn the link to the right clockwise you will make it shorter
6. the front tires are both pointing straight 6 Charge a battery pack Charge a battery pack as per the battery manufacturers and or charger manufacturers instructions 7 Adjust the electronic speed control Follow the manufacturers instructions to setup and adjust the speed control for your TEN SCTE 8 Setthe transmitter steering trim Follow the manufacturers instructions to set the steering trim subtrim so that the vehicle goes straight with no input to the steering 9 Setthe transmitter steering endpoints Follow the manufacturers instructions to set the endpoints so that the servo hits full steering upon reaching full input from the transmitter Driving the TEN SCTE Always follow these precautions when running your TEN SCTE Do not run the TEN SCTE at dusk or in the dark when pacer Do not attempt to run this model if it will be out of sight for All DZ9100T S Needs Spacer any amount of time 943572 943587 946497 943607 y Do not run this model near a crowd of people 944527 947587 947377 947387 gt Always check for proper radio function and battery condition 231 before operating az Check to make sure the tires are securely glued to the rims Check the model thoroughly for loose nuts bolts and screws All No 241 before and after running Make sure you use proper dirt tires if running off road All S9102 DOES NOT FIT 25T Never run the model with old or discharged batteries Leave plenty of room to stop the mod
7. If you turn it to the left counterclockwise you will make it longer If you will be making a lot of adjustments you should consider using the LOSA99165 Aluminum Turnbuckle Wrench Static Camber This refers to the angle of the wheels tires relative to the surface viewed from either the front or back Negative camber means that the top of the tire leans in toward the chassis Positive camber means the top of the tire leans out away from the chassis Camber can be precisely measured with after market camber gauges sold at a local hobby shop It can be measured roughly using any square to the ground object by checking the gap between the square edge and the top of the tire Testing has shown that 1 degree of negative camber is best for most track conditions Increasing negative camber in the range of 1 2 degrees will generally increase steering Decreasing negative camber in the range of 0 1 degree will generally decrease steering and the TEN SCTE will feel easier to drive as a result This is most often a very critical adjustment in tuning your TEN SCTE that can be made quickly and easily Inboard Camber Location The TEN SCTE has two different inner locations with vertical adjustment for the front camber tie rod In general the lower or further out the inside position is relative to the outside the more camber gain total camber change through the total throw of the suspension is present This is an adjustment that is difficult
8. VIEW CHASSIS EXPLOSIONSZEICHNUNG VUE ECLATEE DU CHASSIS VISTA ESPLOSA DEL TELAIO B2124 B4003 A6350 4006 82360 A6258 A6240 Z SN N RUS O NU SY PIE Sb NV II 0 9 2010 Horizon Hobby Inc Not responsible for typographical errors The Spektrum trademark is used with permission of Bachmann Industries Inc Losi Xcelorin and MultiPro are trademarks or registered trademarks of Horizon Hobby Inc Airtronics is a registered mark of Sanwa Electronic Instrument Co Ltd Osaka Japan Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan KO PROPO is a registered trademark of Kondo Kagaku Co Ltd Tokyo Japan Printed 11 2010 30160
9. able to process a return or accept it for exchange Safety Precautions and Guidelines Age Recommendation Not for children under 14 years This is not a toy Always operate this RC model in a safe reasonable and cautious fashion When driving the TEN SCTE avoid someone being hit by the vehicle You may cause serious injury to another person or to personal property should you make contact while running the TEN SCTE General e This RC Vehicle is not intended for use on public highways or roads e Avoid areas that have many pedestrians or crowds of people Keep in mind that this vehicle is radio controlled and can experience moments of radio loss or interference provide for a margin of error at all times Be aware that the motor and batteries of this RC vehicle will get HOT during each use Be careful not to burn yourself Batteries and Charging The TEN SCTE uses rechargeable batteries such as NiMH These batteries all have special requirements to preserve performance and last e Read all instructions provided by the manufacturer of the batteries Never allow minors to charge battery packs e Always check to ensure the polarity of battery connection is correct Never leave batteries unattended while charging e Never charge a battery while it is installed in the TEN SCTE Do not charge any battery that appears to have any f there are exposed wires do not charge or use the b
10. screws 2 Install pinion gear recommendations supplied earlier 3 Slide motor with adapter into motor mount set mesh and tighten using 5 40 x 3 8 button head screw Be sure to use threadlock In addition to the tools included with the TEN SCTE you will find the following both useful and in some cases necessary Small flat blade and Phillips screwdrivers Needle nose pliers o Quality 050 inch 1 16 inch 5 64 inch 3 32 inch 1 5mm and 2 5mm hex Allen drivers Required Equipment Electronic Speed Control We recommend the Xcelorin Sensored Brushless Speed Control Motor Any 550 sized motor Battery We recommend the Xcelorin 7 4V 60C 25 6000mAh LiPo LOSB9877 Charger We recommend the Xcelorin MultiPro Intelligent LiPo Balancing Charger LOSB9606 Servo Preferably Spektrum S6040 Receiver and Electronic Speed Control Installation Install with double sided tape Be sure to route wires so they will not get caught in the spur gear Pinion Gear Any Mod 1 Pinion Gear Note We recommend a Losi LOSA3576 16T pinion gear for 4 5T 550 can motor or a Losi LOSA3577 17T pinion gear for 5 5T 550 can motor Servo Installation use following diagrams 1 Install servo as shown in diagram using the four supplied 4 40 x 1 2 in screws and washers Please look at supplied chart to determine if spacers are needed Paint always test the paint on material removed from the body 2 Choose correct servo horn adap
11. to make a generic statement as it can have slightly different results in various conditions The following is a summary of how this adjustment will usually impact the handling of the TEN SCTE A longer front camber link will usually make the TEN SCTE feel stiffer This will help keep the TEN SCTE flatter with less roll but can make the TEN SCTE handle worse in bumpy conditions It also will make the TEN SCTE easier to drive A shorter front camber link will result in more front end roll which will provide more steering on tighter turns with the loss of some stability You will also lose some high speed steering but might gain some more steering response Too short of a front link may make the TEN SCTE feel twitchy wandery meaning that it may be difficult to drive straight at high speed Toe In Out This is the parallel relationship of the front tires to one another Toe in out adjustments are made by changing the overall length of the steering tie rods Toe in the front of the tires point inward to a point in front of the front axle will make the TEN SCTE react a little slower but have more steering from the middle of the turn out The opposite is true with toe out the front of the tires point outward coming to a point behind the front axle the TEN SCTE will turn into the corner better but with a decrease in steering from the middle of the turn out Toe in will help the TEN SCTE to track better on long straight high sp
12. www horizonhobby com Inspection or Repairs If this Product needs to be inspected or repaired please use the Horizon Online Repair Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization RMA number Pack the Product securely using a shipping carton Please note that original boxes may be included but are not designed to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not responsible for merchandise until it arrives and is accepted at our facility An Online Repair Request is available at www horizonhobby com http www horizonhobby com under the Repairs tab If you do not have internet access please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for repair When calling Horizon you will be asked to provide your complete name street address email address and phone number where you can be reached during business hours When sending product into Horizon please include your RMA number a list of the included items and a brief summary of the problem A copy of your original sales receipt must be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping carton Notice Do not ship batteries to Horizon If you have any issue with a battery plea
13. x 2 5 Ball Bearing 2 0583553 Center Differential Outdrive Set 10 T LOSA6947 5 x 11 Sealed Ball Bearings 2 LOSB3555 Center Front CV Driveshaft Assembly 10 T LOSA6954 5x 10 x 4 Sealed Ball Bearings 2 LOSB3556 Center CV Driveshaft Couplers 10 LOSA6956 12 x 18 x 4 Sealed Ball Bearings 2 LOSB3563 F R Differential Outdrive and Hard Set 2 LOSA6957 10 x 15 x 4 Sealed Ball Bearings with LOSB3564 F R CV Driveshafts and Couplers 2 10 T Plastic Retainer 2 LOSB3565 F R CV Couplers 4 10 T LOSA6958 6 x 12 x 4 Sealed Ball Bearings with LOSB3568 Differential Seals Pin and Gasket 10 T Plastic Retainer 2 LOSB3569 Differential Gear Set with Hardware 10 T LOSA7215 Eclipse SCT Tires with Foams LOSB3571 Front Ring and Pinion Gear Set 10 T 2787 5237 Part Number LOSA5224 LOSA5225 LOSA5226 LOSA99004 LOSA99006 LOSA99013 LOSA99015 LOSA99104 LOSA99165 LOSA99772 LOSA99173 LOSA99174 LOSA99202 LOSA99203 LOSA99217 Description Certified Shock Fluid 30 wt Certified Shock Fluid 35 wt Certified Shock Fluid 40 wt Losi Cargo Bag Losi Pit Roller Carrier Pit Boxes Losi Large Pit Mat Losi Pit Apron Losi Wrench Set US 4 pc Aluminum Turnbuckle Wrench Camber Gauge Ride Height Gauge Car Stand Losi Lok Threadlock Blue High Pressure Black Grease Nitrotec Cleaner Spray OPTIONAL PARTS LIST LOSB2167 LOSB2171 LOSB2172 LOSB2173 LOSB2130 LOSB2223 LOSB2224 LOSB2846 LOSB2907 LOSB2908 LOSB2909 LOSB2960
14. 3574 Axle 2 TEN SCTE LOSB2022 Rear Suspension Mount Cover TEN SCTE LOSB3578 Center Rear Drive Shaft TEN SCTE LOSB2023 Rear Suspension Arm Set 10 T LOSB3592 Differential Standoff TEN SCTE LOSB2100 Front Spindles and Carriers 10 T LOSB4003 F R Camber Steering Turnbuckle Set 10 T LOSB2103 Rear Hubs and Spacers 10 T LOSB4023 Rod End Set 15 10 T LOSB2123 Steering Bellcrank Set 10 T LOSB4022 Camber and Steering Ball Set 12 10 T LOSB2124 Steering Posts Tube and Hardware 10 T LOSB4109 Suspension Hinge and King Pin Set 10 10 T LOSB2163 Front Shock Towers and Caps 10 T LOSB4210 Steering Throttle Brake Link Set 10 T LOSB2170 Rear Shock Tower 10 T LOSB7018 Wheel Set 2 TEN SCTE LOSB2211 Front and Rear Pin Mount Cover Set 10 T LOSB7019 Beadlock Ring with Screws Chrome XXX SCT LOSB2213 Pivot Pin Mount Set 4 10 T TEN SCTE 2 10582222 Front and Rear Sway Bar Set 10 LOSB8028 TEN SCTE Clear LOSB2278 Chassis Brace and Spacer Set 3 10 T LOSA4006 Antenna Kit LOSB2279 Steering Drag Link and Hardware 10 T LOSA6204 4 40 x 1 2 Cap Screws LOSB2359 Radio Tray with Switch Cover Blank and LOSA6206 4 40 x 3 8 Cap Screws Receiver Cover TEN SCTE LOSA6227 4 40 x 1 8 Setscrews LOSB2411 Chassis TEN SCTE L0SA6229 4 40 x 3 8 Button Head Screws LOSB2412 Top Brace TEN SCTE L0SA6240 5 40 x 1 2 Cap Screws LOSB2413 Motor Mount with Adapter TEN SCTE LOSA6250 4mm 5mm Setscrews LOSB2414 Body Posts TEN SCTE LOSA6254 2 56 x 1 4 Cap Screws
15. CLUSIVE REMEDY OF THE PURCHASER This warranty covers only those Products purchased from an authorized Horizon dealer Third party transactions are not covered by this warranty Proof of purchase is required for all warranty claims b Limitations HORIZON MAKES NO WARRANTY OR REPRESENTATION EXPRESS OR IMPLIED ABOUT NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCT THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER S INTENDED USE c Purchaser Remedy Horizon s sole obligation hereunder shall be that Horizon will at its option i repair or ii replace any Product determined by Horizon to be defective In the event of a defect these are the Purchaser s exclusive remedies Horizon reserves the right to inspect any and all equipment involved in a warranty claim Repair or replacement decisions are at the sole discretion of Horizon This warranty does not cover cosmetic damage or damage due to acts of God accident misuse abuse negligence commercial use or modification of or to any part of the Product This warranty does not cover damage due to improper installation operation maintenance or attempted repair by anyone other than Horizon Return of any Product by Purchaser must be approved in writing by Horizon before shipment Damage Limits a HORIZON SHALL NOT BE LIABLE FOR SPECIAL INDIRECT OR CONSE
16. LOSB2415 Battery Tray with Stop Tab Pad LOSA6256 4 40 x 1 2 Button Head Screws and Screws TEN SCTE LOSA6264 8 32 x 3 8 Flat Head Screws LOSB2416 Battery Straps 2 TEN SCTE LOSA6270 5 40 x 3 8 Flat Head Screws LOSB2417 Rear Bumper Pack TEN SCTE LOSA6271 5 40 x 1 2 Flat Head Screws LOSB2418 Rear Mud Flap 2 XXX SCT TEN SCTE LOSA6272 5 40 x 3 4 Flat Head Screws LOSB2419 Sideguards TEN SCTE LOSA6275 5 40 x 5 8 Flat Head Screws LOSB2421 Front Bumper Pack TEN SCTE LOSA6277 5 40 x 3 8 Button Head Screws LOSB2825 Front Shock Body Set 10 T LOSA6278 5 40 x 1 2 Button Head Screws LOSB2826 Rear Shock Body Set 10 T LOSA6279 5 40 x 3 4 Button Head Screws LOSB2845 Front and Rear Shock Shaft Set 10 T LOSA6282 5 40 x 7 8 Button Head Screws LOSB2904 Front and Rear Shock Plastics and Ball Set 4 10 T LOSA6286 5 40 x 5 8 Button Head Screws LOSB2905 Front and Rear Shock Boots 8 10 T LOSA6290 8 32 x 1 2 Button Head Screws LOSB2906 Shock Rebuild Set 2 10 T LOSA6293 8 32 x 1 4 Setscrews LOSB2961 Front and Rear Spring Set 4 Med Black 10 T LOSA6295 10 32 x 3 8 Setscrews LOSB3104 Front and Rear Gearbox Set 10 T LOSA6298 8 32 x 1 8 Setscrews LOSB3436 40T Spur Gear Mod 1 TEN SCTE LOSA6299 5 40 x 1 8 Setscrews LOSB3495 Wheel Hex 4 with Pins TEN SCTE LOSA6302 5 40 Steel Lock Nuts LOSB3536 Center Differential Mount and Shock Tool Set 10 T LOSA6350 4 and 1 8 Inch Hardened Washer 24 LOSB3542 Differential Housing and Seal Set 10 T LOSA6907 5 8
17. QUENTIAL DAMAGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCT WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANTY NEGLIGENCE OR STRICT LIABILITY Further in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted As Horizon has no control over use setup final assembly modification or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting liability If you as the Purchaser or user are not prepared to accept the liability associated with the use of this Product you are advised to return this Product immediately in new and unused condition to the place of purchase Law These Terms are governed by Illinois law without regard to conflict of law principals 12597 Warranty Services Questions Assistance and Repairs Your local hobby store and or place of purchase cannot provide warranty support or repair Once assembly setup or use of the Product has been started you must contact Horizon directly This will enable Horizon to better answer your questions and service you in the event that you may need any assistance For questions or assistance please direct your email to productsupport horizonhobby com or call 877 504 0233 toll free to speak to a Product Support representative You may also find information on our website at
18. attery until you install shrink wrap or replace the complete wire When charging NiMH batteries select a charger to meet your requirements You need a charger that is a 100 240V wall charger or one which requires a 12V power supply Follow the charger manufacturer s instructions and precautions during each use Quick Start Note Please read the entire manual to gain a full understanding of the TEN SCTE vehicle fine tuning the setup and performing maintenance 1 Read the safety precautions found on this page 2 Charge the battery pack you have chosen NOT INCLUDED Refer to the Manufacturer s Supplied instructions for battery charging information 3 Install the AA batteries into the Transmitter Use alkaline or rechargeable batteries only 4 Install a fully charged battery pack 5 Turn the transmitter and then the vehicle Always turn the transmitter on before the vehicle and turn it off after the vehicle has been turned off 6 Check steering Verify that the servo is functioning properly 7 Driving the TEN SCTE 8 Performing maintenance of the TEN SCTE El Lan 2557 Peak Detection Charger Peak detection chargers monitor the battery during charging and automatically shut off upon full charge You can either purchase a peak detection charger that plugs into a household AC wall socket or one that requires you to also purchase a 12V power supply If using a charger other than a peak detection charge
19. eed runs where toe out has a tendency to make the TEN SCTE wander We recommend to run between 0 degree of toe in out to 1 degree of toe in Differentials The TEN SCTE comes equipped with grease in all three differentials You can switch to oil Thinner front oil increases off power steering but if the oil is too thin the steering will become grabby and inconsistent Thicker front differential oil increases off power stability and increases on power steering Thinner center differential has less forward drive can unload more under acceleration and is easier to drive on rough and slick tracks Thicker center differential has more acceleration increases on power steering and less off power steering Thinner rear differential has more cornering traction and increases steering in the middle of the turn Thicker rear differential has less steering in the middle of the turn and more forward traction 523 Tuning the Rear End of the TEN SCTE 31V Shock Location Moving the shocks out on the arm will result in less forward traction and let the TEN SCTE make more of an arc through the exit of the turn In general when changing shock locations on the arm it will be necessary to go down one spring rate when moving out on the arm Static Camber Having the same definition as for the front end and measured in the same fashion rear camber can also be a critical tuning feature Testing has shown that running a small amoun
20. el It will take as much room to stop as it did to accelerate 5 PDS 2123 2344 2363 2365 2366 23T SIIUOAUIY Tuning Adjusting and Maintaining the TEN SCTE Periodically examine your TEN SCTE for the following Keep your vehicle clean using a brush to remove dirt and dust Look for cracks in the suspension arms and other molded parts e Check that the tires are still glued to the wheels Check that all the wheel bearings are clean and lubricated Using your tools attempt to tighten all the screws and nuts e Verify that the Camber Links and Steering linkage are not bent e Check that the Toe and Camber settings are as desired and equal e Check the Drivetrain o Check the Spur gear for wear o Check the Pinion gear e the shocks off the vehicle and check especially if they appear to be leaking as it is time to rebuild them Look over all the wiring and connections for bare wire or any place which could lead to a short circuit After you become familiar with driving your TEN SCTE you may need to reset or make adjustments for better driving performance Just as in a real car alignment is an important factor in your vehicle s handling When you are ready to make adjustments itis a good idea to have a flat work space to place your vehicle on This will enable you to easily and more quickly make both Toe in and Camber adjustments These adjustments should be set with the ve
21. hange the spring stiffness as it will NOT Wheels and Tires The tires come pre mounted with the vehicle and should be checked to make certain they stay glued to the wheels The wheel spinning speeds this vehicle is capable of tend to pull the rubber tire away from the rim When a tire or tires come loose from the rim you will notice the vehicle is hard to control Tip the vehicle on its side and using both hands to hold one wheel at a time use your thumb to press the tire away from the rim If you see a tire pull away from the rim use Losi Tire Glue LOSA7880 thick or LOSA7881 thin to reglue It only takes a small drop of glue generally Be careful this is CA type glue and you do not want to glue your fingers to the wheel and tire Use safety goggles when gluing tires Check the mounting of the tire periodically to ensure proper performance and handling Troubleshooting your TEN SCTE Many questions are the result of simple user errors or minor adjustments which are easily addressed If after reading below you cannot resolve your problem then please contact the appropriate Horizon product support department HW 3A Servicing Your Shocks From time to time you should check your shocks for adequate fluid If the fluid is low or it is getting dirty you should change the fluid in the shocks You may also want to change the shock fluid and or the pistons to better address the conditions you are running on Regardless of wha
22. hicle sitting at its normal ride height Three Position Battery Tray Your TEN SCTE comes with a three position battery tray to alleviate the need for foam blocks You can move the included battery stops in order to run the battery in a back middle or forward position Please see pictures as follows FORWARD Z LIN 5237 Maintenance In addition to the service needs pointed out in this guide you should try to maintain your new TEN SCTE for proper performance and to prevent wear If dirt gets in the moving parts it can seriously hinder the performance of the model Use compressed air a soft paintbrush and or a toothbrush to remove dirt and dust Avoid using solvents if possible as this can actually wash the dirt into bearings and areas not accessible without disassembly causing additional wear We suggest you follow these basic guidelines Remove as much freestanding dirt dust as noted above Never leave the battery plugged in while vehicle is not running Inspect the chassis for worn broken or binding parts and repair as necessary Maintaining Differentials Remove differential from vehicle using exploded view Clean loose dirt off using brush Open differential as shown in diagram Clean out internals using motor spray Fill with oil to your liking and reverse steps to reinstall 21 12 cl Tuning the Front End of the TEN SCTE 72 87 Shock Location
23. orward traction and initial steering but reduce straightaway speed Decreasing rear toe in will decrease forward traction and free up the TEN SCTE Less toe in can be used to gain top speed Ride Height This is the height of the chassis in relation to the surface It is an adjustment that affects the way your TEN SCTE jumps turns and goes through bumps To check the ride height drop one end front or rear of the TEN SCTE from about a 5 to 6 inch height onto a flat surface Once the TEN SCTE settles into a position check the height of that end of the TEN SCTE in relationship to the surface To raise the ride height lower the shock adjuster nuts on the shock evenly on the end front or rear of the TEN SCTE that you are working on To lower the ride height raise the shock adjuster nuts Both left and right nuts should be adjusted evenly Check the setup sheet included and for additional setup information visit www losi com 5237 Use the same technique to adjust the rear ride height Again refer to the included setup sheet Every driver likes a little different feel so you should try small ride height adjustment to obtain the feel you like This should be the last adjustments you make after everything else is dialed in Note Do not use ride height adjustments as a substitute for a spring rate change If your TEN SCTE needs a softer or firmer spring change the spring Do not think that simply moving the shock nuts will c
24. paign Illinois 61822 USA productsupport horizonhobby com 877 504 0233 United Kingdom Horizon Hobby Limited Units 1 4 Ployters Rd Staple Tye Harlow Essex CM18 7NS United Kingdom sales horizonhobby co uk 44 0 1279 641 097 Germany Horizon Technischer Service Hamburger Str 10 25335 Elmshorn Germany service horizonhobby de 49 4121 46199 66 France Horizon Hobby SAS 14 Rue Gustave Eiffel Zone d Activit du R veil Matin 91230 Montgeron infofranceghorizonhobby com 33 0 1 60 47 44 70 Compliance Information for the European Union INSTRUCTIONS FOR DISPOSAL OF WEEE USERS IN wm THE EUROPEAN UNION This product must not be disposed of with other waste Instead it is the user s responsibility to dispose of their waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or where you purchased the product 3T 2557 REPLACEMENT PARTS LIST Part Number Description LOSB3572 Rear Ring and Pinion Gear Set 10 T LOSB2021 Front Suspension Arm Set 10 T LOSB
25. r make sure your battery is fully discharged prior to charging Many of these have a 15 20 minute timer that allows you to set a charge time If the battery is not fully discharged you can potentially over charge your battery pack Do not charge any battery unattended and monitor for heat build up If the battery pack is more than warm to the touch immediately discontinue charging Read all safety precautions supplied by the charger and battery manufacturer Supplied and Required Equipment Supplied tools Wheel Wrench Four 4 Hex L Wrench Set 050 inch 1 16 inch 5 64 inch and 3 32 inch Shock Bottom wrench Turnbuckle Shock Top wrench The Losi 5 Overview pn xn Rear Shock Sway Bar a 2 2n un Ve Rear Camber Link Rear Suspension Arm ESC with Fan not included Motor not included Center Differential Battery Tray Receiver Location Steering Servo not included Tie Rod Front Suspension Arm lt 2 Front Shock Front Camber Link Sway Bar 2557 Tools You Will Find Handy Basic Electronics Installation Instructions A Caution Please be sure to follow the electronics manufacturers guidelines when installing and setting up your radio motor servo electronic speed control and battery Motor Installation Follow diagram below 1 Install motor adapter onto motor with two supplied M3x10mm
26. se contact the appropriate Horizon Product Support office Warranty Inspection and Repairs To receive warranty service you must include your original sales receipt verifying the proof of purchase date Provided warranty conditions have been met your Product will be repaired or replaced free of charge Repair or replacement decisions are at the sole discretion of Horizon Non Warranty Repairs Should your repair not be covered by warranty the repair will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50 of the retail purchase cost By submitting the item for repair you are agreeing to payment of the repair without notification Repair estimates are available upon request You must include this request with your repair Non warranty repair estimates will be billed a minimum of Y hour of labor In addition you will be billed for return freight Horizon accepts money orders and cashiers checks as well as Visa MasterCard American Express and Discover cards By submitting any item to Horizon for inspection or repair you are agreeing to Horizon s Terms and Conditions found on our website under the Repairs tab United States Electronics and engines Horizon Service Center 4105 Fieldstone Rd Champaign Illinois 61822 USA 877 504 0233 Online Repair Request visit www horizonhobby com repairs All other products Horizon Product Support 4105 Fieldstone Rd Cham
27. sult in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision Do not attempt disassembly use with incompatible components or augment product in any way without the approval of Horizon Hobby Inc This manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or serious injury 3T Introduction Thank you for choosing the TEN SCTE We are confident you will be satisfied with the performance of this durable and resilient vehicle Please read through the entire manual before setting up and using your vehicle Register your Losi Product Online Register your TEN SCTE now and be the first to find out about the latest options parts product updates and more Log on to www LOSI com and follow the product registration link to stay connected Getting Ready Thoroughly read all the enclosed material precautions and follow instructions to avoid damaging your new RC vehicle If you choose to not follow these steps or instructions it will be considered negligence If after review of this manual and prior to running your TEN SCTE you determine this RC vehicle is not what you want Do Not proceed and Do Not run the TEN SCTE If the TEN SCTE has been run your local hobby store will not be
28. t of negative camber 5 1 degree is best Increasing negative rear camber in the range of 1 5 3 degrees will increase stability and traction in corners but decrease high speed stability Decreasing rear camber in the range of 0 1 5 degrees will decrease stability and traction in corners but will increase high speed stability Inboard Camber Location The TEN SCTE has two inner camber link locations These locations work in the same fashion and have the same effect as noted for the front You will find that you will get more noticeable changes with the outer locations in the hub In general the upper hole will make the TEN SCTE more stable and keep the front end flatter This works well on higher traction surfaces The lower location will make the steering more aggressive which works well on lower traction surfaces This can be good in some conditions but can also make the TEN SCTE difficult to drive in others Outboard Camber Location Running the camber link in the inside position on the hub will generate more rotation entering a turn but decrease steering on exit Running the camber link in the furthest outer position on the hub will generate more stability entering a turn and increase steering on exit Toe In Having the same definition as for the front end the toe in can be adjusted on the TEN SCTE with the rear hubs The stock toe in is degrees of inboard per side and 0 degrees in the hub Increasing rear toe in will increase f
29. t the reason you will want to follow these simple steps to service refill and bleed your TEN SCTE shocks If you are cleaning or changing the fluid you will find the LOSA99217 Nitrotec Spray Cleaner to be the quickest and easiest way to remove oil fluid and dirt safely 1 If you are changing the pistons clean the threads on the end of the shock shaft and apply threadlock LOSA99202 to the threads 2 Install the small shock piston washer and shock piston using the 4 40 mini lock nut on the shock shaft to secure them 3 Puta drop of shock fluid on the shaft before replacing it in the shock body 4 Ifyou are changing the shock end use the shock tool provided with the TEN SCTE to hold the shaft You will see that this plastic tool has serrations on both sides that allow you to hold it with a pair of pliers and not scratch up the micro finished surface This method works very well to protect the shock shafts from damage 5 After installing make sure the shaft is fully extended when filling the shock 6 the shock body with 30 35 weight shock fluid until it is to the top of the Body 7 Workthe shock shaft up and down a few times This will release the air bubbles trapped beneath the piston 8 Place the filled shock in the upright position off to the side for a few minutes until the air bubbles escape from the fluid 9 Once all the air bubbles are out of the fluid gently place the shock bladder onto the top of the shock
30. ter using servo horn chart to make sure the paint and body material are compatible and press onto servo 3 After servo is centered install servo horn on servo using the screw provided with your servo so that in the centered position the servo horn is parallel to the servo saver arm Two Channel Radio We recommend a Spektrum DX3R or DX3S transmitter and matching receiver Dala Before Running Your TEN SCTE 1 the differentials While holding the chassis with only the left side tires firmly on the ground give the car about one eighth throttle for 30 seconds The right side tires should spin freely during this time Repeat this with only the right side tires firmly on the ground allowing the left side tires to spin freely Repeat this 2 3 times 2 Check for free suspension movement All suspension arms and steering components should move freely Any binds will cause the car to handle poorly 3 Settheride height Set the ride height of your truck with all components installed so that the bottom of the chassis is 29 5mm from the ground in the front and 24 5mm in the rear by adjusting the shock collars 4 Set the camber Adjusting the camber tie rod length changes the camber Set the front tires to have 0 degrees of camber at ride height Set the rear tires to have 2 5 degrees of negative camber at ride height 5 Set the front toe in Adjust the steering tie rods so that when the servo is centered on the transmitter
Download Pdf Manuals
Related Search