Source Controller - Extron Electronics
Contents
1. 32 RS485 adapter can be used in lieu of direct RS485 The required cabling will vary depending on brand and model of adapter used Consult the IP Link device and the adapter manuals for pinouts The last method RS232 to iCAN requires an iLight serial node A M F straight modem cable Extron Electronics P N 26 433 01 and a F F 9 pin DSUB gender changer Extron Electronics P N 10 438 10 are required between the IP Link device and the iLight serial node for this method This is the only connection method that can be used with source controllers lacking RS485 ports If either method that utilizes RS232 is chosen the user must change the port type to RS232 in the IP Link device s default web pages If the IP Link device is reset the port type will change back to RS485 Consult the user s manual for your IP Link device for more information Serial communication Port Type RS 485 Parity None Baud Rate 9600 Stop Bits 1 Data Bits 8 Flow Control None Pin Assignments Diagram Signal Pin Main Cable R3485 a RS485 v a 2 RS232 DB9 Male n IP Link Device Interface Page 4 of 5 it 13 2105_7 pke IP Link Device Interface s Revision 10 17 2013 Communication Sheet General Notes Page 5 of 52. it 13 2105 7 pke IP Link Device Interface Revision 10 17 2013 Communication Sheet This document provides additional assistance with wiring your Extron IP Link enabled product to your device Different components may reguire a different wiring scheme than those listed below For complete operating instructions refer to the user s manual for the specific Extron IP Link enabled product or the controlled device manufacturer supplied documentation Device Specifications Device Type Lighting Control Manufacturer iLight Firmware Version N A Model s Source Controller Version History Driver Version 7 IP Link GC Date Compiler Version Notes 10 8 2013 1 6 0 351 Extron Certified Version Made changes to the wiring diagram and status 4 2 2013 15 1 332 Fixed Channel Level Status Accounted for the response echoing back the guery 02 10 2011 1 4 0 3 0 4 Fixed command strings for Scene Recall Save 05 11 2010 140 3 0 3 Added Scene Status Changed Scene Select and Recall functions to drop down menus Custom version Added Ouery Enable to allow user to guery the n k ee a device or not Changed Port Type from RS 485 to RS 232 12 30 2009 1 4 0 3 0 2 Updated for TLP compatibility 02 25 2005 1 0 9 3 N A Initial version Page 1 of 5 it 13 2105 7 pke IP Link Device Interface Revision 10 17 2013 Communication Sheet Driver Notes e The Save Scene function can save to the Current Scene or to any sce
3. ne 1 99 Once the command is completed it will return to Select Scene Recall shows the current scene e Current Scene will not work if Scene Recall is set to Off e Default Area and Channel is set to 1 and the default fade time is set to 0 e All functions require certain options to be selected before they are executed Channel X Channel Level Step X Fade Stop X Scene Recall Scene Save Page 2of5 it 13 2105 7 pke IP Link Device Interface Revision 10 17 2013 Communication Sheet Control Commands amp States Stop Off 1 99 C 59 gt E O Ferm O Soene Rect fom Current Scene 1 99 Status Available Channel Level 0 to 100 in steps of 1 Connection Status Connected Disconnected Scene Recall Off 1 99 Channel Level status is unavailable when Channel Select is set to ALL MLC60 Series Supported Commands User defined commands are recommended to be used for control with the MLC60 series Page 3 of 5 it 13 2105 7 pke IP Link Device Interface E Revision 10 17 2013 Communication Sheet Cable and Adapter Requirements A custom cable may be required There are three methods of connecting the IP Link device to the source controller RS485 RS232 to RS485 adapter RS232 to iCAN The RS485 method is the most straight forward and is the one presented in the wiring diagram on the next page Any commercially available RS2
Download Pdf Manuals
Related Search