User Manual - B&H Photo Video Digital Cameras, Photography
Contents
1. Appendix D Extending Wireless Signal Range 2 4 GHZ Directional Wireless Panel Antenna Use the 2 4GHz Directional Wireless Panel Antenna model ACCANTD9 to focus a wireless signal onto the camera in order to increase the range of transmission clear line of sight between the camera and the antenna is required A 20ft extension cable is included to help to properly position the antenna Directional Wireless Panel Antenna Wireless Receiver Directional Panel U Antenna NS v SN Clear line of sight AS Wireless Camera KF Cable from Directional EN Panel Antenna Outdoor installation Indoor connection Scenario 1 Single Receiver Installation Attach a directional antenna to the camera and or the receiver It is recommended to attach the antenna to the receiver and place it in a location that has clear line of sight to the camera Ensure that the directional antenna is pointing toward the other antenna For example if the directional antenna is connected to your receiver the directional antenna should point at the camera see figure above During the installation check the reception on your DVR Scenario 2 Multiple Camera Receiver Installation If you are using multiple wireless cameras and receivers in your installation attach directional antennas to the camera s and receiver s that are farthest away from each other Follow these guidelines to inc2. SFSR Spread Spectrum FHSS Operating Temperature Range 14 F 1229F 10 C 40 C 1 Maximum wireless transmission range Actual range dependent upon building materials and other obstructions in path of wireless signal 8 2 Receiver Specifications RX Sensitivity 81dBm FSR Supported Resolution VGA 640x480 up to 30 frames per second 53 x 137 x 86mm 2 1 x 5 4 x 3 4 with antenna attached Weight 0 1kg 0 3lbs 8 3 Camera Specifications Image Sensor Type 1 4 Color CMOS Image Sensor Field of View Diagonal OCR Power Consumption 430mA Max with IR LED 220mA Max without IR LED IR LED Quantity Type 24 pieces 850nm Night Vision Range 135ft 41m 90ft 27m Built in Auto IR Turn On Off CdS Drive Auto IR LED turn On Off Circuit Dimensions W x D x 79 x 203 x 117mm 3 1 x 8 0 x 4 6 with antenna and sun shade Weight 0 3kg 0 6lbs 1 Not intended for submersion in water Installation in a sheltered area recommended 2 Stated IR illumination ranges are based on ideal conditions in typical outdoor night time ambient lighting and in total darkness Actual range and image clarity depends on installation location viewing area and light reflection absorption level of object Appendix B Frequently Asked Questions 9 Appendix B Frequently Asked Questions 9 1 Wired vs Wireless Cameras A wired camera has a video cable that transmits the video signal from the camer
3. Service 1 Servicing Do not attempt to service this video equipment yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 2 Conditions Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions A When the power supply cord or plug is damaged B If liquid has been spilled or objects have fallen into the product C If the product has been exposed to rain or water D If the product has been dropped or the cabinet has been damaged E If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation F When the product exhibits a distinct change in performance This indicates a need for service 7 Replacement Parts When replacement parts are required have the service technician verify that the replacements used have the same safety characteristics as the original parts Use of replacements specified by the product manufacturer can prevent fire electric shock or other hazards 8 Safety Check Upon completion of any service or repairs to this product ask the service technician to
4. LOREX WIRELESS SECURITY CAMERA INSTRUCTION MANUAL ENGLISH VERSION 1 0 VANTAGE www lorextechnology com Thank you for purchasing this product This manual refers to the following models e LW2231 learn more about this product and to learn about our complete range of accessory products please visit our website at www lorextechnology com CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RICK OF ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF THE PLUG TO THE WIDE SLOT AND FULLY INSERT VAN NS LOREX VIEW YOUR WORLD NEED HELP CONTACT US FIRST EIVE VANTAGE an Z DO NOT RETURN THIS PRODUCT TO THE STORE Please make sure to register your product at www lorextechnology com to receive produc
5. one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 5 Power Sources This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied to your location consult your video dealer or local power company For products intended to operate from battery power or other sources refer to the operating instructions power cords damaged or cracked wire insulation and broken plugs are dangerous They may result in a shock or fire hazard Periodically examine the cord and if its appearance indicates damage or deteriorated insulation have it replaced by your service technician 7 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them Pay particular attention to cords at plugs convenience receptacles and the point where they exit from the product 8 Surge Protectors It is highly recommended that the video equipment be connected to a surge protector Doing so will protect the equipment from damage caused by power surges Surge protectors should bear the UL listing mark or CSA certification mark 9 Uninterruptible Power Supplie
6. Type Pre attached to the receiver Pairing Status LED Glows green continuously when a camera is paired to the receiver Flashes on and off slowly when pairing mode is active and flashes rapidly when camera is out of range Pairing Button For details see Pairing Cameras on page 9 DC Power Connect power adapter to power on the receiver 02 Termination Cable Includes BNC video output cable and RCA audio output BNC Vid Antenna Jack RCA Audio Wireless Camera 3 Wireless Camera 1 Microphone Removable Antenna SMA Pre attached to the back of camera Camera Stand DC Power Connect power adapter to power on the camera Pairing Button For details see Pairing Cameras on page 9 Oo Cc CO N Antenna Jack ATTENTION This camera includes an Auto Mechanical IR Cut Filter When the camera changes between Day Night viewing modes an audible clicking noise may be heard from the camera This clicking is normal and indicates that the camera filter is working Installing the Camera 4 Installing the Camera 4 N Camera is suitable for outdoor installation Installation in a sheltered location is recommended For example install under shelter protected from the elements such as beneath roof eaves The diagram to the right shows an example of an ideal location for outdoor placement No x 4 1 Installation Warnings e Aim the camera to o
7. a to a recording or viewing device A wireless camera does not use a video cable Instead it wirelessly transmits the video signal to a wireless receiver that is connected to your DVR Wireless cameras do not require video cabling to be run between the camera and the DVR which reduces installation time and cost 9 2 Does a wireless camera require power Yes Wireless cameras require two power sources one connected to the camera and the other to the receiver The term wireless refers to the lack of a video cable between the camera and the receiver 9 3 How far can a wireless camera transmit a video signal In an open field with line of sight a typical wireless camera has a range between 250 500 feet Line of sight means that there are no obstructions between the camera and receiver Obstructions include walls buildings trees and certain electronic devices Materials containing moisture for example leaves may also act as an obstruction Cubical walls drywall glass and windows generally do not degrade wireless signal strength In a closed environment such as the interior of a house the wireless camera range is between 100 165 feet The signal range varies depending on the type of building materials or objects the wireless signal must pass through The signal range also depends on whether there are competing signals using the same frequency as the camera For example signals from cordless phones or routers may affect si
8. ause a hazard 12 Water and Moisture Do not use receivers or video monitors near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement near a swimming pool and the like 13 Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat 14 Accessories Do not place this video equipment on an unstable cart stand tripod or table The video equipment may fall causing serious damage to the product Use this product only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Any mounting of the product should follow the manufacturer s instructions and use a mounting accessory recommended by the manufacturer 15 Camera Extension Cables Check the rating of your extension cable s to verify compliance with your local authority regulations prior to installation 16 Mounting The cameras provided with this system should be mounted only as instructed in this guide or the instructions that came with your cameras using the provided mounting brackets 17 Camera Installation Cameras are not intended for submersion in water Not all cameras can be installed outdoors Check your camera environmental rating to confirm if they can be installed outdoors When installing cameras outdoors installation in a sheltered area is required vi
9. cts and documentation Please read the Quick Start Guide and User Manual before you install this product e Consumer Guides and Video Tutorials are available on our web site at www lorextechnology com support e If you require further installation assistance please visit www lorextechnology com installation or contact a professional installer e Please note that once the components of this product have been unsealed you cannot return this product directly to the store without the original packaging e LOREX VIEW YOUR WORLD VANTAGE FEB 12 2013 R9 AVANT DE COMMENCER ANTES DE EMPEZAR Vevillez enregistrer votre produit sur le site www lorextechnology com afin de recevoir des mises jour et le soutien technique pour votre procluit CE PRODUIT PEUT N CESSITER UNE INSTALLATION PROFESSIONNELLE LOREX S ENGAGE R PONDRE VOS BESOINS EN MATIERE DE S CURIT Nous avons concu et d velopp une documentation et des produits extr mement conviviaux Veuillez lire le Guide de d part rapide et le Guide d utilisation avant d installer ce produit Des guides pour consommateurs et des tutoriels vid o vous sont offerts sur notre site Web www lorextechnology com support e Si vous avez besoin de plus d assistance pour l installation de ce produit veuillez visiter le site www lorextechnology installation ou communiquez avec un installateur professionnel Veuillez prendre note que lo
10. es renseignements sur les produits guides d utilisation guides de inicio r pido y preguntas m s frecuentes en de d part rapide et FAQ www lorextechnology com support www lorextechnology com support Para todo lo dem s visite Pour toutes les autres questions www lorextechnology com visitez www lorextechnology com e f oe e Por tel fono Par t l phone Norte Am rica En Am rique du Nord Atenci n al cliente para asuntos de la garant a garant a v lida s lo Service la client le pour tout ce qui concerne la garantie en E U A vea la garant a ofrecida por el importador 1 888 425 6739 1 888 42 LOREX 1 888 425 6739 1 888 42 LOREX Soutien technique pour les questions d ordre technique ou relatives Asistencia t cnica para asuntos t cnicos o de instalaci n l installation 1 877 755 6739 1 877 75 LOREX 1 877 755 6739 1 877 75 LOREX Mexique 001 800 681 9263 001 800 514 6739 Tel fono y Servicios V lidos S lo en E U A 001 800 681 9263 001 800 514 6739 International 800 425 6739 0 par exemple partir du Royaume Uni composez le OO au lieu de Internacional 800 425 6739 0 12 2013 RIS BEFORE YOU START Please make sure to register your product at www lorextechnology com to receive product updates and technical support THIS PRODUCT MAY REQUIRE PROFESSIONAL INSTALLATION LOREX IS COMMITTED TO FULFILLING YOUR SECURITY NEEDS e We have developed user friendly produ
11. gnal strength Adaptive Frequency Hopping Spread Spectrum FHSS technology featured in the latest Lorex models greatly reduce signal interference Range Limiting Factors A A pe zt A 74 Reflection Scattering Refraction Diffraction Attenuation The signal Thesignalscatters Thesignalbends The signal The signal reflects back back into multiple as it travels changes direction strength weakens new signals through an as it passes as it passes object e g glass around an object through an object window Source Xirrus 2010 Wi Fi Range Dynamics Retrieved online at http xirrus gcsmarket com pdfs Xirrus Wi Fi Range pdf Appendix B Freguently Asked Guestions Signal Reduction Through Materials Signal strength decreases as it passes through different types of material The table below shows how signals become reduced when passing through different materials Material Signal Reduction 96 Plaster amp Wood 10 3096 Brick 30 5096 Concrete Cinder Blocks 50 7096 Metal amp Metal Cladding 70 9096 NOTE Signals that must pass through wet or moist materials e g shrubs and trees may be significantly reduced The stronger the signal strength the higher the video frame rate The lower the signal strength the lower the video frame rate pp Fullsignalstrength Low signal streng
12. ipment Please read them carefully before operating and using your product General Precautions All warnings and instructions in this manual should be followed 2 Do not use receivers or video monitors in humid or wet places 3 Keep enough space around the product for ventilation Slots and openings in the storage cabinet should not be blocked 4 Itis highly recommended to connect the product to a surge protector to protect from damage caused by electrical surges It is also recommended to connect the product to an uninterruptible power supply UPS which has an internal battery that will keep the product running in the event of a power outage 5 Remove the plug from the outlet before cleaning Do not use liquid aerosol detergents Use a water dampened cloth for cleaning Installation 6 Overloading Donotoverload wall outlets or extension cords as this can result in the risk of fire or electric shock Overloaded AC outlets extension cords frayed Read and Follow Instructions All the safety and operating instructions should be read before the product is operated Follow all operating instructions Retain Instructions The safety and operating instructions should be retained for future reference Heed Warnings Comply with all warnings on the product and in the operating instructions Polarization Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with
13. ndix C Troubleshooting If you have problems with your system there is often a quick and simple solution Please try the following Solution There is no picture from the Make sure that the camera is plugged into a power outlet and that 5 the power adapter is plugged in properly Make sure receiver is plugged into a power outlet Move the camera closer to the receiver Make sure BNC video output cable is connected to your DVR or television e If you are viewing your camera s using a TV make sure you have the correct input selected There is no audio from the Make sure the RCA audio output cable is connected to your DVR 5 television audio input Make sure audio recording is enabled on your DVR See your DVR manual for further instruction Make sure to remove the protective film from the camera lens The microphone is located on the front of the camera and will not work properly if the protective film is left on The picture is dropping Move the camera closer to the receiver e Try repositioning the camera receiver or both to improve the reception The picture is or has become The picture may become choppy when experiencing a lower frame choppy rate e g 6 frames per second vs a higher 20 frames per second e Try moving the camera closer to the receiver Remove obstructions between the receiver and camera The picture is white e Washout or white wash can occur when a st
14. nnecting to a DVR 9 Connecting to a DVR Before powering on the receiver make sure to first connect and power on the camera This will ensure a proper connection 1 Connect the BNC video cable from the receiver to the video input on your DVR 2 Connect the RCA audio cable from the receiver to the corresponding audio input The audio input number or name should match the video input where you connect the BNC cable e g Video Input 1 and Audio Input 1 3 Connect the power cable to the power port on the receiver and plug it into a power outlet or surge protector 4 Place the receiver where it will have clear reception to your camera NOTE If your camera is out of range the pairing status LED will flash on and off rapidly OPTIONAL Use the double sided tape to secure the receiver to a surface e g wall 1 Avoid installing in a location which requires the wireless signal to pass through cement con crete and metal structures This will reduce the range of transmission Connecting to a TV 6 Connecting to a TV RCA BNC S VIDEO BNC to RCA Adapter 1 Connectthe included BNC to RCA adapter to the BNC connector on the receiver Connect the other end of the BNC to RCA adapter to the RCA video input on your television 2 Connectthe RCA audio connector from the receiver to the audio input on your television 3 Connect the power cable to the power port on the receiver and pl
15. nting bracket viii At full signal strength Limit number of obstructions to ensure best performance Audio recording without consent is illegal in certain jurisdictions Lorex Technology Inc assumes no liability for use of its products that does not confirm with local laws Stated IR illumination ranges are based on ideal conditions in typical outdoor night time ambient lighting and total darkness Actual range and image clarity depends on installation location viewing area and light reflection absorption level of object Camera and receiver requires a wired connection to an electrical outlet power adapters included Not intended for submersion in water Installation in a sheltered area required Maximum wireless transmission range Actual range dependent upon building materials and other obstructions in path of wireless signal Table of Contents Ne Getting Started seras k kek ces 1 2 Wireless 2 3 Wireless Camera 3 4 Installing the Camera 4 Installation Warnings 4 2 2 Mad POSTOR D 43 the Camera as oe cue belet Pemex Dre a PI Ves 5 5 Connecting to a DVR ou xac ke c cR cR aC 7 6 Connecting toa TV 8 7 Pairing lt 9 8 Appendix A System Specifications 10 8 General Specifica
16. perform safety checks recommended by the manufacturer to determine that the product is in safe operating condition Use 1 Cleaning Unplug the product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 2 Product and Cart Combination Product and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the product and cart combination to overturn 3 Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result ina fire or electric shock Never spill liquid of any kind on the product 4 Lightning For added protection of this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges STRANGULATION HAZARD Infants have STRANGLED in power cords Keep power cords more than 3 feet away from cribs bassinets play yards and other safe sleep environments for infants NOTICES FCC Notice This eguipment has been certified and found to comply with the limits regulated by the FCC part 15 subpart C Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2
17. ptimize the viewing area select a location that provides a clear view of the area you want to monitor that is free from dust and that is not facing a strong light source or direct sunlight e Avoid installing the camera where there are thick walls or obstructions between the camera and the receiver e Avoid installing in a location which requires the wireless signal to pass through cement concrete and metal structures This will reduce the range of transmission For details see Appendix B Frequently Asked Questions on page 11 e Select a location for the camera that has an ambient temperature between 14 F 122 F 10 C 50 C e Not intended for submersion in water For outdoor use installation in a sheltered location is recommended Installing the Camera 4 2 Mounting Positions You may mount your camera on a wall ceiling or counter See the images below for recommended configurations of the camera stand and antenna we Wall Ceiling Counter NOTE For ceiling installation position the antenna as high as the ceiling allows See the Ceiling mounting position in the figure above Before mounting the camera permanently carefully plan where and how the camera will be positioned and where you will route the cable that connects the camera to the power adapter Verify the camera s performance by observing the image on a monitor when the camera is positioned where it will be permanently installed 4 3 To Ins
18. rease the signal strength between your cameras and receivers Point directional antennas towards the receiver for each camera Keep as much space as possible between each receiver Keep as much space as possible between directional antennas if using more than one e Minimize the amount of obstructions e g walls or trees between the antennas and receivers During the installation check the reception of each camera on your DVR Visit www lorextechnology com for more details on wireless antennas and accessories VANTAGE ALWAYS AWARE W2231 Version 1 0 www lorextechnology com Copyright O 2013 Lorex Technology Inc
19. rong light source is pointed at the camera lens The camera lens is not harmed during a white wash Do not point your camera towards a bright light source The picture is too dark e f using during the day the camera may not be getting enough light Reconsider the position of your camera The picture is too bright e If using during the day the camera may be getting too much light Reconsider the position of your camera Night vision is not working Night vision activates when light levels drop The area may have too much light Bright spot in video when Night vision reflects when pointing a camera at a window Move viewing camera at night the camera to a different location Appendix D Extending Wireless Signal Range 11 Appendix D Extending Wireless Signal Range DISCLAIMER Certain accessories are not available in all markets There are several ways to boost your wireless signal as well as options to help you extend the range of the wireless signal Clear Line of Sight You should always try to ensure there is a clear line of sight between the camera and the ge Clear line of sight Receiver Extending Your Wireless Signal Even with a clear line of sight between your 5 and your receiver s you may experience a lower video frame rate simply due to the distance between your wireless devices Accessory antennas are available that can help extend the range of your wireless signal
20. rsque vous avez d ball les pi ces et composantes de ce produit vous ne pouvez pas retourner celui ci directement au magasin sans son emballage original Cerci rese de por favor colocar su producto en www lorextechnology com para recibir actualizaciones y la informaci n del producto y soporte t cnico ESTE PRODUCTO PUEDE EXICIR UNA INSTALACION PROFESIONAL LOREX SE COMPROMETE A SATISFACER SUS NECESIDADES EN SEGURIDAD Favor de leer la gu a de instalaci n r pida y la gu a del usuario antes de instalar este producto Puede conseguir las gu as del consumidor y los cursos en ensefianza video sobre el Internet visitando www lorextechnology com support Si necesita ayuda para la instalaci n visite www lorextechnology com installation o contacte un especialista en instalaciones Favor de notar que una vez que los componentes de este producto han sido removidos del embalaje no podr devolver este producto directamente a la tienda www lorextechnology com LOREX cc VIEW YOUR WORLD VOIR VOTRE MONDE VEASU MUNDO FEB 12 2013 R Important Safeguards In addition to the careful attention devoted to quality standards in the manufacture process of your product safety is a major factor in the design of every instrument However safety is your responsibility too This sheet lists important information that will help to ensure your enjoyment and proper use of the product and accessory equ
21. ry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesirable operation This Class B digital apparatus complies with Canadian ICES 003 Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada MODIFICATION Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the device Toute modification non approuv e explicitement par le fournisseur de licence de l appareil peut entra ner l annulation du droit de l utilsateur utiliser l appareil RoHS This product is fully compliant with the European Union Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment RoHS Directive 2002 95 EC The RoHS directive prohibits the sale of electronic equipment containing certain hazardous substances such as lead cadmium mercur
22. s UPS Because this product is designed for continuous 24 7 operation it is recommended that you connect the product to an uninterruptible power supply An uninterruptible power supply has an internal battery that will keep the product running in the event of a power outage Uninterruptible power supplies should bear the UL listing mark or CSA certification mark Caution Maintain electrical safety Power line operated equipment or accessories connected to this product should bear the UL listing mark or CSA certification mark on the accessory itself and should not be modified so as to defeat the safety features This will help avoid any potential hazard from electrical shock or fire If in doubt contact qualified service personnel Installation Continued 10 Ventilation Slots and openings in the case are provided for ventilation to ensure reliable operation of the product and to protect it from overheating These openings must not be blocked or covered The openings should never be blocked by placingthe video equipment on a bed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register This product should not be placed in a built in installation such as a bookcase orrackunless proper ventilation is provided and the product manufacturer s instructions have been followed 11 Attachments Do not use attachments unless recommended by the product manufacturer as they may c
23. t updates and technical support 2 Easy Ways to Contact Us Online Product Support is available 24 7 including product information user manuals quick start up guides and FAQ s at www lorextechnology com support For all other matters visit www lorextechnology com By Phone North America Customer Service for warranty matters 1 888 425 6739 1 888 42 LOREX Tech Support for technical installation issues 1 877 755 6739 1 877 75 LOREX Mexico 001 800 68 1 9263 001 800 5 14 6739 International 800 425 6739 0 Example From the UK dial 00 instead of FEB 12 2013 R15 OLOREX VANTAGE VIEW YOUR WORLD VOIR VOTRE MONDE VEA SU MUNDO NECESITA AYUDA BESOIN D ASSISTANCE COMUN QUESE PRIMERO COMMUNIQUEZ D ABORD CON NOSOTROS AVEC NOUS NO DEVUELVA ESTE PRODUCTO A LA TIENDA NE RETOURNEZ PAS CE PRODUIT AU MAGASIN Por favor registre su producto en www lorextechnology Veuillez enregistrer votre produit sur le site com para recibir actualizaciones del producto y www lorextechnology com afin de recevoir des mises jour asistencia t cnica et le soutien technique pour votre produit Hay 2 maneras f ciles de comunicarse 2 facons simples de communiquer con nosotros avec nous e En linea En ligne Apoyo al cliente est disponible 24 7 incluyendo votre disposition 24 7 le soutien pour les produits comprend informaci n del producto manuales para el usuario gu as l
24. tall the Camera Use the included mounting screws to mount the camera to the mounting surface Mark the positions of the screw holes on the mounting surface Teese e Drill holes and insert the drywall plugs included as needed pease e Firmly attach the camera to the mounting surface using the included screws eel NOTE If you are running the power cable through the mounting surface connect power before firmly attaching the camera to the mounting surface NOTE If you are running the power cable along the mounting surface you need to run the power connector cable through the cable notch on the camera base before firmly attaching the camera to the mounting surface Cable Notch Installing the Camera 2 Loosen the thumbscrews 1 2 and the adjustment ring 3 by turning them counter clockwise L 0 46 3 Adjust the angle of the camera until the desired view is set Tighten the thumbscrews and the adjustment ring to secure the camera s position 4 Connect the power cable from the camera to the weatherproof power connector Plug the power adapter into a power outlet or surge protector NOTE Power cables are only weatherproof when fully inserted at the connection point Power cables may not be submerged in water 5 Remove protective film from the camera lens to uncover the microphone The protective film may prevent the microphone from working if not removed Co
25. th high frame rate low frame rate 9 4 Are digital wireless camera signals secure Yes Lorex digital wireless products feature a wireless transmission method called Frequency Hopping Spread Spectrum FHSS This type of signal is highly resistant to eavesdropping as it generates a channel hopping sequence using an algorithm generated by the receiver which only the camera can follow through the pairing function Pairing is an electronic handshake between digital wireless devices Digital wireless cameras can only be paired to one receiver This is to prevent interception by third parties and prevents any other device from picking up the signal this also means that you cannot pair one camera to multiple receivers 9 5 How many frames per second should I expect from a digital wireless camera Current Lorex digital wireless cameras offer 10 30 FPS Frames Per Second performance Actual frame rate depends mainly on signal strength see the chart in section above For details on supported resolutions and frame rates for this model see Appendix A System Specifications on page 10 9 6 How many wireless cameras can l install Itis recommended to install a maximum of 4 wireless cameras per system 4 receivers and 4 cameras Minimum space between receivers should be 4 inches 10cm and minimum space between cameras should be 6 5ft 2m to minimize potential signal strength degradation Appendix C Troubleshooting 10 Appe
26. this device must accept any interference received including interference that may cause undesired operation This eguipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This eguipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this eguipment does cause harmful interference to radio or television reception which can be determined by turning the eguipment on and off the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the eguipment and receiver e Connect the eguipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio or television technician for assistance Warning To ensure compliance with the FCC s RF exposure guidelines this equipment should be installed and operated with minimum distance 20cm 7 87in between the radiator and nearby persons Industry Canada Notice This device complies with Indust
27. tions s 2a ico doit rca teh doi RR LA Ab elu anten dd oben 10 8 2 Receiver Specifications s de a 10 8 3 Camera SpecificationS crisi rca ada a AA da 10 9 Appendix B Frequently Asked Questions 11 9 1 Wired vs Wireless Cameras 11 9 2 Does a wireless camera require power 11 9 3 How far can a wireless camera transmit a video signal 11 9 4 Are digital wireless camera signals secure 12 9 5 How many frames per second should I expect from a digital wireless camera 12 9 6 How many wireless cameras l install 12 10 Appendix C Troubleshooting 13 11 Appendix D Extending Wireless Signal Range 14 Getting Started 1 Getting Started The system comes with the following components 1 X WIRELESS CAMERA 1 X WIRELESS RECEIVER 2 X POWER ADAPTERS FOR CAMERA amp RECEIVER 1 X MOUNTING KIT 1 X WHITE CAMERA ANTENNA 1 X BLACK RECEIVER ANTENNA PRE ATTACHED PRE ATTACHED Mounting kit contents may differ from image 1 X BNC TO RCA ADAPTER 2 X DOUBLE SIDED TAPE 1XINSTRUCTION MANUAL 1 X QUICK START GUIDE CHECK YOUR PACKAGE TO CONFIRM THAT YOU HAVE RECEIVED THE COMPLETE SYSTEM INCLUDING ALL COMPONENTS SHOWN ABOVE Wireless Receiver 2 Wireless Recelver md 2 Removable Antenna SMA
28. ug it into a power outlet or surge protector 4 Power on your television and select the input that the receiver is connected to 5 Place the receiver where it will have clear reception to your camera 1 Avoid installing in a location which requires the wireless signal to pass through cement con crete and metal structures This will reduce the range of transmission Pairing Cameras 7 Pairing Cameras IMPORTANT The camera and the receiver have already been paired out of the box which means that they are exclusively communicating with each other If for some reason the pairing is lost follow these steps to pair the camera and receiver To pair the camera to the receiver 1 Make sure that the camera and receiver are both powered up and all antennas are properly attached 2 Press and hold the PAIR button on the receiver for 5 seconds to activate pairing mode The pairing status LED will flash on and off slowly Pairing Status LED Pair button 3 Press the PAIR button on the back of the camera within 30 seconds of pressing the PAIR button on the receiver e f pairing is successful live video from the camera will appear on the monitor em Pair button Appendix A System Specifications 8 Appendix A System Specifications 10 8 1 General Specifications TX Frequency Range 2 400GHz 2 480GHz KE Unobstructed Effective Range 165ft 50m indoor 500ft 152m outdoor
29. y hexavalent chromium PBB and PBDE in the European Union It is imperative that the user follows the guidelines in this manual to avoid improper usage which may result in damage to the product electrical shock and fire hazard injury In order to improve the features functions and quality of this product the specifications are subject to change without notice from time to time Please see the label on your device for FCC IC certification numbers Vii Features e Real time up to 30fps wireless video with MPEG 4 compression d 640x480 VGA resolution e Extended bandwidth delivers super smooth high frame rate video e SignalGuard Technology continuously monitors the wireless signal and automatically reconnects upon detecting low signal strength e Next generation adaptive Frequency Hopping Spread Spectrum FHSS technology greatly reduces conflicts with competing signals Built in microphone for listen in audio Built in auto mechanical infrared camera filter achieves accurate color reproduction in varying lighting conditions e Night vision range up to 135ft 41m 90ft 27m e Simple installation No video cable required e Weatherproof camera and power connectors can be installed indoors or outdoors e Easily connects to any surveillance DVR BNC or TV RCA e High gain antennas provide up to 165ft 50m indoor 500ft 152m outdoor wireless range e Vandal resistant camera design with cable pass through mou
Download Pdf Manuals
Related Search