LPR 1274W 7 x 10 W RGBW 4-IN
Contents
1. ei SOH LPR 1274W 7 x 10 W RGBW 4 IN 1 SUPER BRIGHT LED PAR LIGHT User s Manual Troubleshooting 1 If the power supply indicator doesn t light up and the light doesn t work please check the power supply the input voltage and the fuse 2 In Stand Alone operation if the power supply indicator is light up and sound active indicator isn t light up but the light is shut off doesn t work A Because sound is too small make for light shut off in sound active please increase the music volume or increase audio sensitivity with sensitivity knob please check as below B Please check if unit has been set up in slave mode then set up in master mode 3 In Master Slave operation slave unit don t function please check as below A Make sure to there s only one master in the chain and the others are set in slave mode B Make sure to control the unit without DMX console controlling C Make sure to take a good quality power cable and connection 4 In DMX mode operation the light is OFF and the DMX signal indicator is unlighted please check as below A Make sure to set up the DMX mode B Make sure to have a good connection 5 In DMX operation the unit can t be controlled by the DMX console but the DMX signal indicator is flashing please make sure the DMX console and unit have the same channel 6 If the unit is fail please turn off the unit then turn on again after 5 minutes Warranty Warnings 1 Damages caused by2. Page 2 the common can cause a ground loop and your fixture may perform erratically Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other 4 Turn on the all units power the units begins reset then the unit begins working The slave units will react the same as the master unit 5 The units will react to the low frequencies of music via the internal microphone Adjust the audio sensitivity knob on the back of the master unit to make the unit more or less sensitive in sound active The panel has LED indicating for sound active Universal DMX Operation DMX mode This mode allows you to use universal DMX 512 console to operate 1 Install the units in a suitable position laying or appending 2 Use standard XLR microphone cable chain your units together via the XLR connector on the rear of the units For longer cable runs we suggest a terminator at the last fixture 3 Assign a DMX address to each the unit using dipswitches see the DMX Address Quick Reference Char Light No 1 Tight No 2 Tight No 3 Lette wae a a On N 9m F x j C NM x 8 sO ne lt ee lt 1 DMX Signal l MASTER SOUND AUTO DMX 2 SLAVE 2 SLAVE 4 Turn on the all units power the units begins reset then the unit begins working 5 Use DMX console to control your units Notes 1 DMX console can not be used in Master Slave
3. color dimmer controlled under CH8 CH7 Color change 61 110 Page 8 General instructions Unpacking Thank you for purchasing this product Please read user guide for safety and before using the product Keep this manual for future reference This product can create perfect light programs and effects since it has passed a series of strictly tests before delivery Please check the attachments listed on the page after opening the carton Immediately upon receiving a fixture carefully unpack the box Check the box contents to ensure that all parts are present and that they are in good condition If any part appears damaged from shipping or if the box shows signs of mishandling notify the shipper immediately In addition retain the box and all the packing material for inspection In any event save the carton and all packing material because in case that you have to return the fixture to the factory you will have to do so in its original box with its original packing 1 LED Light 1PCS 2 Power Cable 1PCS 3 User Guide 1PCS Safty Notice Please read the following notes carefully because they include important safety information about the installation usage and maintenance of this product It is important to read all these notes before starting to work with this product LED Expected Lifespan LEDs gradually decline in brightness over time HEAT is the dominant factor that leads to the acceleration of this decline Packaged in clusters LEDs
4. exhibit higher operating temperatures than in ideal or singular optimum conditions For this reason when all color LEDs are used at their fullest intensity life of the LEDs is significantly reduced It is estimated that a viable lifespan of 40 000 to 50 000 hours will be achieved under normal operational conditions If improving on this lifespan expectancy is of a higher priority place care in providing for lower operational temperatures This may include climatic environmental and the reduction of overall projection intensity There are no user serviceable parts inside the light Any reference to servicing this unit you may find from now on in this User Manual will only apply to properly C we certified technicians Do not open the housing or attempt any repairs unless you are o Please refer to all applicable local codes and regulations for proper installation of the light Keep this manual for future consultation If you sell the light to another user make sure that they also receive this manual Page 1 Power 110V 240V Ground Avoid direct eye exposure to the light source while the fixture is on Always disconnect the light from its power source before servicing Always connect the light to a grounded circuit to avoid the risk of electrocution This product is for indoor use only Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow contact with water or any ot
5. operation Sound Active or AUTO mode 2 There should be only one master unit in Master Slave operation DMX Control The system only accepts the DMX512 signal of international standard to control the system mode the light beam ON OFF running direction running speed and twinkle speed etc Page 7 clockwise direction to decrease The light diode will automatically turn off after 8 seconds when the music stops AUTO Auto cycles the built in programs without being controlled externally It has no light OFF The mode allows a single unit to react to the beat of the music in the master mode 1 Install the units in a suitable position laying or appending 2 Set dipswitch to select Sound Active or AUTO mode 3 Turn on the unit power the unit begins reset then the unit begins working 4 The unit will react to the low frequencies of music via the internal microphone Adjust the audio sensitivity knob on the back of the unit to make the unit more or less sensitive in sound active The panel has LED indicating for sound active Master Slave Operation This mode will allow you to link up to 32 units together without controller 1 Install the units in a suitable position laying or appending 2 Choose a unit to function as Master mode set dipswitch to select Sound Active or AUTO mode The others must be set to Slave mode set dipswitch to select Slave mode 3 Use standard XLR microphone cable chain your units together v
6. the disregard of this user manual are not subject to Warranty The dealer will not accept liability for any resulting defects or problems 2 Please consider that unauthorized modifications on the device are forbidden due to safety reasons Please note that damages caused by manual modifications on the device or unauthorized operation by unqualified persons are not subject to warranty 3 If this device will be operated in any way different to the one described in this manual it may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock etc After trying the above solution you still have a problem please contact your dealer or our company for service Page 9 DMX Control The LED light only accepts the DMX512 signal of international standard to control the light DMX Control Parameter Chart 4 Channels 0 255 Red brightness dark to bright CH2 0 255 Green brightness dark to bright Brightness 05255 0 255 Blue brightness dark to bright 0 255 White brightness dark to bright 9 Channels O 255 White brightness dark to bright No strobe Strobe AUTO strobe speed slow to fast 250 255 Sound Active strobe cris spect 02255 Stat color cleo o speed conta sow vo xt QO 127 White color ON White color O 255 White color OFF Aass ond at working 11 60 Manually select static color controlled under CH8 61 110 JAUTO
7. 40 C Cooling system air cool Item Size 18cm 10cm Net weight 1 1kg Gross weight 1 5Kg inner box Kg outer box Inner box 225 210 170 0 008m3 Outer box 465 435 561 0 114m3 12pcs carton Fixture Dimension Fixture Apperance Power supply Input power switch ON OFF key menu menu enter up enter Cooling fan LCD Digital Operation Introduction MENU DMX control colors selection colors pulse colors transition sound control amnual set DOWN UP previous or next increase or decrease O Enter confirm and save the selection MENU Up DOWN ENTER Page 4 LCD Digital Operation Details MENU Description Under DMX512 mode or Master Slave mode Under DMX512 001 512 d001 d512 means the value press Down UP to increase or decrease the value then press ENTER to save the selection Manually color selection C001 C255 001 255 255 kinds of static color Under Uoff white color Off MODE 0 64 Value has 64kinds of static colors press Down Up to increase the value AUTO color dimmer rb01 rb16 Value 01 16 dimmer speed press Down Up to change the speed AUTO color Pulse ON OFF simultaneously PLO1 PL16 Value 01 16 pulse speed press Down Up to change the speed AUTO color Jumping Sd01 Sd16 Value 01 16 jumping speed press Down Up to change the speed AUTO Strobe FLO1 FL16 01 16 means strobe speed leve
8. her fluids or metallic objects Mak h eee n Please prevent this light away flammable materials close to the fixture s while operating from electrical shock When hanging this fixture always secure it to a fastening device using a safety cable not provided Always make sure that you are connecting the light to the proper voltage as per the specifications in this manual or on the product s sticker Never connect the light to a dimmer pack Make sure that the power cable is not cracked crimped or damaged Ne The maximum ambient temperature Ta is 104 F 40 C Do not operate the fixture at a higher temperature In case of a serious operating problem stop using this product immediately Use cleaning tissue to remove the dust absorbed on the external lenses periodically to optimize light output Do not remove or break the warranty label otherwise it void the warranty Always replace with the exact same type fuse replacement with anything other than the specified fuse can cause fire or electric shock and damage your unit and will void your manufactures warranty There are no serviceable parts in the light Please have all servicing and adjustments made by a qualified service engineer Don t throw this product away just as general To protect the environment d trash please dispose of this product following the abandon electronic product regulation in you recycle packing material country wherever possible
9. ia the XLR connector on the rear of the units For longer cable runs we suggest a terminator at the last fixture Cabling must have a male XLR connector on one end and a female XLR connector on the other end Cable Connectors Cabling must have a male XLR connector on one end and a female XLR connector on the other end COMMON X Termination reduces signal errors To avoid signal transmission problems and interference it is always advisable to connect a DMX signal terminator Resistance 120 ohm 1 4w between pin 2 DMX and pin 3 DMX of the last fixture Caution Do not allow contact between the common and the fixture s chassis ground Grounding Page 6 Technical Specification Voltage AC110V 130V 200V 250V 50HZ 60HZ Fuse 3A 250V Rated Power 75W LED Light 10W x 7pcs RGBW LED diodes Working Modes DMX Sound Active AUTO Master Slave DMX Control Channel 4 and or 9 channels Advanced LED technology Popular using in world Extremely long life rated 60 000 to 100 000 hr Very low power consumption no duty cycle runs all light Super bright for indoor use Built in automated programs via stand alone mode by Menu Button 4 Digit Digital LED Display Lighting effects adjustable strobe speed color change adjustable brightness 3 pin male amp female XLR interface Light body plastic Working condition indoor use only Working environment temperature 0 C
10. l press Down UP to increase or decrease the value then press Enter to save the selection Sod1 Sound Active color Jumping Sod2 Sound Active color strobe No sound the light is blackout Sod3 Sound Active color dimmer r000 255 Manual set the Red LED brightness G000 255 Manual set the green LED brightness b000 255 Manual set the Blue LED brightness d4ch Under DMX512 mode it s 4 Channels Press DOWN UP to change mode d9ch Under DMX512 mode it s 9 Channels U ON White color ON Press DOWN UP to change mode U Off White color Off Function amp Setting Sound Active The change of the light pattern is controlled by sound that is the rhythm of the sound control the effect of the changing light pattern Turning the sensitivity knob in the clockwise direction to increase the fixture s sensitivity to sound the knob in the counter Page 5
Download Pdf Manuals
Related Search