Marine PC MPC-SL19 USER MANUAL
Contents
1. Page 13 Display location and mounting options Your display can be mounted using the flush mounting kit supplied MarinePC recommends that you power the unit and select a suitable mounting location prior to installing the display When planning the display location the following points should be considered to ensure safe comfortable and reliable operation e Convenience the mounting location should be easily accessible to allow operation of the controls and should enable easy viewing of the display Power connections The power connection to the display should be made at either the output of the battery isolator switch or at a DC power distribution panel MarinePC recommends that power is fed directly to the display via its own dedicated cable system and MUST be protected by a thermal circuit breaker or fuse fitted close to the power connection If you do not have a thermal circuit breaker or fuse in your power circuit you MUST fit an in line breaker or fuse to the positive red lead of the power cable amp 29 e Installation angle the display should be mounted at an angle Mounting it in a flat plane is not recommended due to increased heat absorption Viewing angle this LCD has been chosen to give the very best performance including viewing angle However the contrast and colors seen on all LCD displays vary slightly with viewing angle e Environment to prevent overheating do not restrict airflow at the2. 3 Using a suitable screwdriver tighten the mounting bracket screws to secure the monitor in position Vertical fixing Umm Page 12 4 Connect all cables as required see Rear connections below Rear connections 10 The rear connectors i 2 3 4 5 6 7 8 9 FUSE Power Input DVI 1 Input DVI 2 Input VGA 1 Input VGA 2 Input CVBS 1 Input Composite Video for AV input CVBS 2 Input Composite Video for AV input CVBS 3 Input Composite Video for AV input 10 5232 Input 11 USB for Touch control option Planning the installation Before you install your display the following points should be considered e Power requirements e Display location and mounting options e Additional accessories e g keyboard or speakers Power requirements Your Sunlight Viewable display is designed to run on boat s DC power systems rated at 12 V or 24 V The MarinePC MPC SL19 is equipped with 9 36V DC wide range power input The DC power system should be either e Negative grounded with the negative battery terminal connected to the boat s ground e Floating with neither battery terminal connected to the boat s ground Grounding the display It is important that an effective radio frequency RF ground is connected to the display You must ground the display by connecting the drain wire shield of the power input cable to the nearest ground point of the boat s RF ground system
3. D Power Voltage Operates on 12V and 24V systems Power Consumption 71W Environmental Operating Temperature 10 C 50 C Non Operating Temperature 20 C 0 C Designed to meet FCC Class A Certification Marine standard EN60945 The brightness is measured under the 25 C ambient temperature before touch attached Due to Panel materials deviation different panel supplier will set different specific variance range to optical characteristics The factors of time used Lamp current ambient temperature will influence the optical measurements Page 28 421 9 16 61 16 7 0 66 376 3 14 81AA 4 VESA Mount Hole 100 0 3 94 75 0 2 95 375 5 14 78 304 1 11 97 301 1 11 85 AA 100 0 3 94 TOUCH EL 68 232
4. also remain at RGB1 position if you keep pressing UP KEY to the end When you press and hold the INPUT KEY the menu screen will show as RGB1 RGB2 3VIDEO34 VIDEO2 If you release the INPUT KEY for 5 seconds without any action the menu selection screen will be closed And it will remain at the item which you d selected When you press MENU BRIGHTNESS PIP Key you will enter the menu item selection Any modified or changed parameter setting will be automatically saved if you power off or Exit the menu setting screen Page 18 PIP KEY 1 Default main screen shows at RGB1 amp RGB2 Press PIP KEY Figure 1 2 Default main screen stays at DVI1 amp DVI2 Press PIP KEY gt Figure 2 3 Default main screen stays at VIDEO 1 2 Press PIP KEY gt Figure 3 1 4 Default main screen stays at VIDEO 2 gt Press PIP KEY Figure 3 2 5 Default main screen stays at VIDEO 3 gt Press PIP KEY gt Figure 3 3 PIP Function Supporting Table RGB 1 RGB2 DVI1 DVI2 VIDEO 1 VIDEO2 VIDEO 3 m e e o ok OK igure 32 ox o X OK Figure 3_2 OK Figure 3_3 OK OK OK OK OK VIDEO 3 OK OK OK OK OK OK OK OK OK DVI 2 RGB 2 VIDEO 1 VIDEO 1 VIDEO 2 VIDEO 2 VIDEO 3 VIDEO 3 OFF OFF Figure 1 Figure 2 Rob 2 2 PGBS NUM 1 BU
5. aluminum case the slim profile MarinePC MPC SL19 is light weight and watertight Front mounted controls and the touch screen make the industrial rugged monitor user friendly We have incorporated the latest optical engineering to achieve optimal viewability in all lighting conditions including direct sunlight The MarinePC MPC SL19 s power efficient low heat design results in increased reliability and longevity required for mission critical deployment This handbook contains important information on the installation operation and maintenance of the MarinePC Sunlight Viewable Marine Display range which is intended for use in the recreational marine market and covers all models Page 8 2 0 CONTROL AND FEATURES Your MarinePC Sunlight Viewable Marine Display has the following controls and features Front View PIP Display Screen OSD Control Power VR Buttons Button Knob Back View N r F FUSE Y 35V DVI YGA CVHS REZ237 Touch 10A Max DC Page 9 3 0 INSTALLATION It is important that your new display is installed and operated in accordance with the instructions provided in this handbook Failure to do so could result in poor product performance and may invalidate your warranty When planning the installation the following points must be considered e Your MarinePC display is sunlight viewable and visible in direct sunlight e If temperatures exceed the normal temperature operating range the display could over
6. monitor should be visible to the driver only if it is used for navigation or system control Care should be taken to ensure distraction does not occur Review all applicable federal state and local laws and regulations to make sure the monitor is used properly and safely Avoid using the monitor for extended times while the charging system is not running or the monitor could drain the watercraft s battery Cleaning the Monitor Use a soft cloth moistened with mild detergent isopropyl alcohol or window cleaners to clean the display housing Never use abrasive cleaners waxes or solvents to clean the unit Page 7 1 0 INTRODUCTION About MarinePC Marine Displays The MPC SL19 is a high performance marine Monitor with optically bonded AR glass or sunlight readable touch screen is especially engineered to survive the most demanding applications You will soon become familiar with the quality difference in this bright sunlight readable 0 5 to 1 000 nits monitor The range of MarinePC Sunlight Viewable Marine Displays has been developed to be used as part of an integrated marine navigation system and or within an entertainment system The displays available in several sizes are designed to be waterproof and suitable for use above or below decks The MarinePC MPC SL19 sunlight readable monitor handles a wide range of extreme environments making it the industry choice for mobile applications Housed in a milled billet
7. rear of the display unit If the space behind the display is air conditioned or cooled by a fan it will help in keeping the unit s temperature down when mounted in direct sunlight FAILURE TO ADEQUATELY VENTILATE THE UNIT COULD INVALIDATE YOUR WARRANTY The display should be protected from physical damage and excessive vibration Although the display unit is waterproof from the front when installed correctly it is good practice to mount it in a protected area away from prolonged and direct exposure to rain and salt spray DO NOT place the display near to a heat source Page 14 Typical Installation Diagram Page 15 4 0 OSD OPERATION PIP Brightness Night Mode Input Down Up Power Menu Introduction Your MarinePC Sunlight Viewable display can be controlled using the On Screen Display OSD menu and or the 8 buttons on the front bezel of the unit The OSD menu enables you to change the way in which your display is set up and is accessed using the Menu button Using the buttons Each of the 8 buttons on the front bezel of your display has an input and a control function Input functions enable you to select the type of signal input to the display Control functions enable you to change the appearance of the display Power Power ON Key To power your monitor ON just need to press this button Power OFF Key To power your monitor OFF just press this button Pressing the power button will display a lis
8. DVI 2 DMI 2 BID VIDEO 2 VIDEO 1 VIDEO 1 VIDEO 3 VIDEO 3 VIDEO 2 OFF OFF OFF Figure 3 1 Figure 3 2 Figure 3 3 Page 19 When you enter the PIP Port Change screen the status bar will remain at OFF position if you keep pressing the DOWN KEY to the end At the other hand the Status bar will remain at top item of each menu if you keep pressing the UP KEY to the end When you press and hold the PIP KEY the menu screen will show as DVI VIDEO1 VIDEO2 VIDEO03 0OFF VIDEO3 VIDEO2 VIDEO1 DVI gt VIDEO1 gt If you release the INPUT KEY for 5 seconds without any action the menu selection screen will be closed And it will remain at the item which you d selected When you press MENU BRIGHTNESS PIP Key you will enter the menu item selection Any modified or changed parameter setting will be automatically saved if you power off or Exit the menu setting screen MENU KEY LJ When you press MENU KEY the Navpixel OSD main menu screen will appear as below fH 1 64 1 64 1 99 CONTRAST H_POSITION Ovi 606 _ RGB 2 1 40 1 64 GREEN GAIN 1 64 MDEO J 1 64 VIDEO Risi 959006 5500865000000 m MEE Elsa FULL FULL EVEN NORAML UTO ADJUST YES EXIT If you release the MENU KEY for 30 seconds without any action the menu OSD screen will disappear auto
9. Marine PC MPC SL19 USER MANUAL 19 IP 65 Marine Display Sunlight Readable LED B L LCD 1st Edition 2009 All information is subject to change without notice Approved by Checked by Prepared by Erik Hank Jack Page 1 RECORD OF REVISION Version and Date Old Description New Description Page 2 TABLE OF CONTENTS RECOLPD OL IRE VIN ari 2 TABLE OF CONIEFNIDu uuu 5 5 5 u ara 9 LO UINTRODUEFONE 8 2 0 CONTROLAND FEAVURES seria 9 SO INSIAGERVION M 10 4 0 ISD OPERA ION c een E 16 5 0 TECHNICAL SPECIFICATION a M UH OH 28 Page 3 IMPORTANT INFORMATION EMC conformance All MarinePC equipment and accessories are designed to the best industry standards for use in the recreational marine environment The design and manufacture of Marine PC equipment and accessories conform to the appropriate ElectroMagnetic Compatibility EMC standards but correct installation is required to ensure that performance is not compromised Waste Electrical and Electronic Equipment Directive The Waste Electrical and Electronic Equipment WEEE Directive requires the recycling of waste electrical and electronic equipment Whilst the WEEE Directive does not apply to some of MarinePC s products we support its policy and ask you to be aware of how to dispose of this prod
10. MarinePC MPC SL19 allow the monitor to be mounted by rear mounted using VESA75 or VESA100 mount PANEL Flush MOUNT For installation there are four tapped mounting holes on the two sides of the unit s panel The mounting hardware packet is included with the product accessories in the shipping box This packet includes four 4 stainless steel threaded studs 3 2 cm and four 4 mounting lock nuts Your monitor can be installed using the mounting lock nuts supplied in the vertical keyways Make sure that both brackets are in the same orientation Preparing the installation site 1 Select an installation site that has sufficient space behind for cable connections and ventilation 2 Tape the supplied flush mount template in the required position 3 Using a jigsaw carefully remove the shaded portion of the template 4 Using a suitable file smooth the edges of the aperture O Please use the provided template to ensure the space correctly Page 11 Installing the display 1 Carefully insert the monitor into the aperture ensuring that your gasket on the rear of the fascia lays flat against the aperture edge IMPORTANT The gasket must lay flat against the aperture edge to ensure watertight integrity 2 Place the mounting bracket lugs into the keyways and move them to the rear securing the bracket to the monitor Note The mounting brackets can be used in either the horizontal or vertical keyways as required
11. VEL Red Color level Adjustment G_LEVEL Green Color level Adjustment B_LEVEL Blue Color level Adjustment TEMPERATURE Color Temperature Adjustment DISP MODE FULL Full Screen EVEN Half Screen NORMAL Keep normal aspect ratio EXIT Quit from current setting Page 22 VIDEO 1 amp 2 amp 3 setting screen 1 CONTRAST DVT PED GAIN GREEN _GAIN 1 64 BLUE_GAIN 1 64 voo TEMPERATURE 5500K 5500K 6500K 7000K 8000K LEE ERE VIDEO 3 oso EXIT 1 64 BEES 1 64 1 64 VIDEO Setting Item Description CONTRAST Contrast Adjustment SHARPNESS Horizontal edge sharpness HUE Color Adjustment R_LEVEL Red Color level Adjustment G_LEVEL Green Color level Adjustment B_LEVEL Blue Color level Adjustment TEMPERATURE Color Temperature Adjustment EXIT Quit from current setting Page 23 PIP Sub menu setting screen PIP SIZE CONTRAST RED GAIN ovr Divi 2 BLUE GAIN EXIT R6B2 MDEO 1 MIDEO2 VIDEOS ol EXIT PIP Setting Item Description PIP_SIZE Picture in Picture Screen Size Adjustment CONTRAST Contrast Adjustment R_LEVEL Red Color level Adjustment G_LEVEL Green Color level Adjustment B LEVEL Blue Color l
12. any action around 5 seconds the VR BRIGHTNESS Status bar image will be closed When you enter the NIGHT MODE or choose BRIGHTNESS Key for brightness adjustment it will be no function if you control the VR knob When you press MENU DISP PIP Key you will enter the menu item selection And the VR BRIGHTNESS status bar image will be closed Any modified or changed parameter setting will be automatically saved if you power off or Exit the BRIGHTNESS status bar Page 17 NIGHT MODE KEY When you press the NIGHT MODE KEY the dimming will be down to under 0 5 nit directly And if you press BRIGHTNESS KEY or VR knob at this moment it will not function until you press the NIGHT MODE KEY again to release this restriction When you press MENU DISP PIP Key you will enter the menu item selection Any modified or changed parameter setting will be automatically saved if you power off or Exit the NIGHT MODE UP DOWN EI KEY It works as menu item selection use the UP KEY can be used as RIGHT KEY and the DOWN KEY can be used as LEFT KEY INPUT KEY When you press INPUT KEY the screen will pop up the following image Roe v 1 BUE VIDEO 1 VIDEO 2 wl ES ese e You can press the UP DOWN KEY for the menu item selection above It will remain at VIDEO 3 position if you keep pressing DOWN KEY to the end And it will
13. evel Adjustment EXIT Quit from current setting Page 24 OSD setting screen REBI 0 1 64 oops pee co c TRANSLUCENT OFF OFF 1 10 DIT c BRIGHTNESS BRILL BRILL VR DV STEM RETURN NO EXIT IDEO IDEO VIDEOS OSD Setting Item Description H_POSITION Horizontal Screen Adjustment V_POSITION Vertical Screen Adjustment TRANSLUCENT Screen background color can be adjusted as transparent as you want total 10 scales BRIGHTNESS Selection between BRIGHTNESS key or VR Button for brightness adjustment SYSTEM RETURN Restore all parameter setting to factory default value EXIT Quit from current setting Page 25 SYSTEM RETURN setting screen RGB 1 H POSITION v POSITION TRANSLUCENT BRIGHTNESS SYSTEM RETURN Rob3 Liv T DYI 2 BRILL NO VIDEO 1 VIDEO VIDEO p EXIT You may choose SYSTEM RETURN selection item on the OSD Screen to restore all of the parameter setting to factory default value When you press UP or RIGHT KEY the parameter will show YES and confirm it RORI RGBZ H POSITION FOSTON TRANSLUCENT BRIGHTNESS SYSTEM RETURN LI T LJ 2 VIDEO 1 Moe VIDEO 3 Left key NO 26 1 64 1 64 OFF 1 10 BRILL SVR J 1 64 1 B4 1 10 BRILL VR All pa
14. heat and begin to blackout due to the limitations of TFT LCD technology e In order to minimize the chances of a malfunction the following precautions should be taken during installation e The display should be installed in an area where there is proper and adequate ventilation min 15cm clearance If it is possible to cool the area behind the display it will significantly reduce the risk of a malfunction e The display should be mounted at an angle to the sun We do not recommend mounting the unit in a flat plane which increases the surface area exposed to the sun and leads to increased heat absorption IMPORTANT Your MarinePC display is only waterproof from the front To maintain watertight integrity the display must be flush mounted ensuring that the rear casing is enclosed in a watertight enclosure and the front is sealed with a waterproof gasket The MarinePC MPC SL19 is designed to be mounted in two configurations VESA75 VESA100 MOUNT The MarinePC MPC SL19 is designed compatible with VESA75 and VESA100 mount By installing the monitor with this kit the user can adjust the viewing angle to improve viewability in changing environments This mounting system has proven to be successful in supporting an extreme amount of weight in high vibration and difficult mount applications The back of the monitor includes mounting points that you can use to mount the monitor as your installation requires Page 10 Mounting holes on the
15. matically You can also choose QUIT and then press MENU KEY to exit this OSD menu screen Page 20 RGB1 amp 2 s setting screen TH PHASE CONTRAST H_POSITION DWT EMI 1 64 1 64 1 99 1 40 1 64 3 FEE GAI 1 64 DEO STO 1 64 Voro TEMPERATURE 5500K 5500K 6500K 7000K 8000K EP MODE FULL FULL EVEN NORAML VOEG AUTO ADULIST YES EXIT RGB Setting Item Description PHASE Horizontal Sampling Phase Adjustment gt CONTRAST Contrast Adjustment H_POSITION Horizontal Screen Adjustment V_POSITION Vertical Screen Adjustment R_LEVEL Red Color level Adjustment G_LEVEL Green Color level Adjustment B_LEVEL Blue Color level Adjustment gt TEMPERATURE Color Temperature Adjustment DISP MODE FULL Full Screen EVEN Half Screen NORMAL Keep normal aspect ratio AUTO ADJUST Auto adjustment EXIT Quit from current setting Page 21 DVI 1 amp 2 s setting screen CONTRAST EN RED GAIN 1 B4j GREEN GAIN 0 li Z Ses I tae Doo TEMPERATURE 5500K S500K 6500K 7000K 8000K ee ISP MOL ULLEVENNOPAR ere DISP_MODE FULL FULL EVEN NORAML OS MSG VIDEO OSD DVI Setting Item Description CONTRAST Contrast Adjustment R_LE
16. rameter setting will be return Right key YES KEY LOCK Mode Function setting screen When you press MENU and BRIGHTNESS KEY simultaneously for 3 seconds you will enter the KEY LOCK mode At the same time the screen will show KEY LOCK image as below for 5 seconds and then disappear In the KEY LOCK mode it will be no function to press any key When you press the key in the KEY LOCK mode the screen will show KEY LOCK image as below for 5 seconds and then disappear KEY LOCK To Release Unlock KEY LOCK Mode Function setting screen In the KEY LOCK mode when you press MENU and BRIGHTNESS KEY simultaneously for 3 seconds you will release unlock the KEY LOCK mode At the same time your screen will show KEY UNLOCK image as below KEY UNLOCK Page 27 5 0 TECHNICAL SPECIFICATION 5 1 General Specification LCD Display Backlight 19 LED Backlight Active Display Area 376 30 x 301 1mm Brightness 1000 cd m2 Resolution 1280x1024 SXGA Contrast Ratio 1000 1 Pixel Pitch mm 0 264 H x 0 264 V Viewing Angle 160 H 160 V Display Color 16 2M Response Time DMS Inputs VGAx2 DVIx2 Composite x3 RS232x1 Picture in Picture 3 stages Mechanical IP Rating Facial waterproof to IP65 standards when console mounted Construction Rugged Aluminum Alloy Chassis Mounting Panel Flush mount VESA mount Dimension 421 9 w x 375 5 H x58 0
17. t of what input for the main screen is associated with each button This is just a reminder and is not part of the input selection process Page 16 BRIGHTNESS Key When you press the BRIGHTNESS Key the screen will show the following image You can press the UP DOWN Key to do the screen brightness adjustment When the brightness achieve 50 and keeping pressing UP Key the dimming will keep the brightness at 50 When you dimming down to brightness 1 and keeping pressing the DOWN Key the dimming will keep the brightness at 1 If you keep pressing BRIGHTNESS Key and hold it the brightness will appear as following status 2 915253 5 5 48 gt 49 50 49 48 if release the BRIGHTNESS Key around 5 seconds with any action the brightness bar will disappear When you press BRIGHTNESS Key and other Key not including Up Down Key the BRIGHTNESS status bar image will disappear When you press NIGHT MODE KEY or choose VR adjustment the BRIGHTNESS KEY will be no function if you press it VR BRIGHTNESS Key If you want to enable the VR Brightness function you need to press MENU KEY and then choose VR function When you rotate the VR knob the VR BRIGHTNESS status bar will appear as below image dimming range from 1 15 Ea When you enter the VR BRIGHTNESS mode it will be no function if you press the BRIGHTNESS KEY And if you release the VR knob without
18. uct The crossed out wheelie bin symbol illustrated above and found on our products signifies that this product should not be disposed of in general waste or landfill Please contact your local dealer national distributor or MarinePC Technical Services for information on product disposal Restriction of the use of certain Hazardous Substances This product uses components that comply with the requirements of the Restriction of the use of certain Hazardous Substances RoHS Directive 2002 95 Warranty Please refer to the latest Warranty Terms and Conditions at www marinepc com Page 4 Packing List Before installation please ensure the following items have been shipped 1 x MPC SL19 Marine Display 4 x Mounting bracket lugs and 4 stainless steel threaded studs 1 x Power Cable 5000 mm 1 x VGA Cable 3000 mm If any of these items should be missing or damaged please contact your distributor or sales representative immediately Page 5 This Page Intentionally left Blank Page 6 Usage Notice 01 To reduce the risk of electric shock do not remove the cover or back There are no user serviceable parts inside 02 Make sure you turn off and unplug the the display before installing WARNING devices Precautions To maximize the life and safe use of your unit always be sure to follow the warnings precautions and maintenance recommendations in this user s guide In a Watercraft or Vehicle e The
Download Pdf Manuals
Related Search