De`Longhi Canada, I - Seattle Coffee Gear
Contents
1. 9 Cleaning the inside of the machine 18 Description of milk container 9 Cleaning the brew group 18 Description of control panel touch screen 9 Cleaning the milk container 19 PRELIMINARY CHECKS 10 DESCALING 19 Controls after WS 10 SETTING WATER HARDNESG 20 Installing the appliance 10 Measuring water hardness 20 Connecting the appliance 10 Setting water hardness 20 Setting up the appliance 11 TURNING THE APPLIANCE ON 11 ee GEASS 20 TURNING THE APPLIANCE OFF 11 DISPLAYED MESSAGES 21 CHANGING THE MENU SETTINGS 12 TROUBLESHOOTING 22 Setting the language 12 LIMITED WARRANTY 24 Setting the clock 12 Setting auto start time 12 Setting the temperature 12 12 Resetting default values reset 13 Statistics function 13 Acoustic signal Beep enabled 13 MAKING COFFEE 13 Selecting the coffee tas2. 10 PRELIMINARY CHECKS Controls after transport After removing the packaging make sure the product is complete and undamaged and that all accessories are present Do not use the appliance if it is visibly damaged Contact Customer Service Installing the appliance Important When you install the appliance you should follow the safety warnings below e The appliance gives off heat After positioning the appliance on the work top leave a space of at least 1 in 3 cm between the appliance and the side and rear walls and at least 6 in 15 cm above the coffee maker e Water penetrating the appliance could cause damage Do not place the appliance near taps or sinks e The appliance could be damaged if the water it contains freezes Do not install the appliance in a room where the temperature could drop below freezing point e Arrange the power cable in such a way that it cannot be damaged by sharp edges or contact with hot surfaces e g electric hot plates Connecting the appliance Important Check that the power outlet Supply voltage corresponds to the value indicated on the rating plate on the bottom of the appliance Connect the appliance to an efficiently earthed and correctly installed outlet with a minimum current rating of 12A only If the power outlet does not match the plug on the appliance have the outlet replaced with a suitable type by a qualified professional Setting up
3. Hot water function the selected message flashes on the display and confirm the selection by pressing the OK icon or cancel the selection by pressing the ESC icon 5 Water flows out of the spout Delivery stops automatically after 8 5 oz 250ml 6 To interrupt delivery of hot water manually press the a icon again Important You should not deliver hot water for more than two minutes at a time Changing the quantity The appliance is factory preset to automatically deliver 8 5 oz 250ml To modify these quantities proceed as follows 1 Position a container under the spouts 2 Once the Hot water function has been selected press and hold the OK icon about 8 seconds until Hot water Program quantity appears and the icon flashes e When the hot water in the cup reaches the required level press the icon again The machine is now reprogrammed with the new quantity 17 CLEANING Cleaning the coffee maker The following parts of the appliance must be cleaned regularly coffee grounds container A18 drip tray A16 water tank A13 coffee spouts A20 and hot water nozzle A11 pre ground coffee feed funnel inside the machine accessible after opening the service door A19 brew group A12 milk container B control panel C A Important Do not use solvents abrasive detergents or alcohol to clean the coffee maker With De Longh
4. 2 Remove the residues with a vacuum cleaner fig 40 Cleaning the brew group The brew group must be cleaned at least once a month N Important The brew group A8 must not be removed when the appliance is on Do not attempt to use force to remove the brew group as this could damage the machine 1 Make sure the machine is correctly turned off see Turning off page 31 2 Open the service door fig 35 3 Remove the drip tray and grounds container fig 36 4 Press the two red release buttons inwards and at the same time pull the brew group outwards fig 41 Important Do not use detergents or lig uid soap to clean the brew group The detergent would remove the lubricant applied to the inside of the piston causing the brew group to seize up and become unusable 5 Soak the brew group in water for about 5 minutes then rinse under the tap 6 After cleaning replace the brew group by Sliding it onto the internal support and pin at the bottom then push the PUSH symbol fully in until it clicks into mo Information lf the brew group is difficult to insert you must first adapt it to the right dimension by pressing it forcefully from the bottom and top as shown in the figure 7 Once inserted make sure the two red buttons have snapped out 8 Replace the drip tray and grounds container 9 Close the service door Cleaning the milk container Clean the milk container each time you
5. The warranty does not cover defects or damage of the appliance which result from repairs or alterations to the appliance outside our factory or authorized service centers nor shall it apply to any appliance which has been subject to abuse misuse negligence or accidents Also consequential and incidental damage resulting from the use of this product or arising out of any breach of contract or breach of this warranty are not recoverable under this warranty Some states do not allow the exclusion or limitation of incidental or consequential damage so the above limitation may not apply to you How do you get service If repairs become necessary see contact information below U S Residents Please contact our toll free hotline at 1 866 528 8323 1 866 Latte Best or log onto our website at www delonghi com For all accessories spare parts or replacement parts please contact our parts division at 1 800 865 6330 Residents of Canada Residents of Canada Please contact our toll free hotline at 1 888 335 6644 or log onto our website at www delonghi com Residents of Mexico Please refer to the Limited Warranty statement for Mexico see page 63 Please refer to the back page of the manual for De Longhi addresses The above warranty is in lieu of all other express warranties and representations All implied warranties are limited to the applicable warranty period set forth above This limitation does not apply if you enter into an extend
6. OK is displayed Press the OK icon fill the water tank and the appliance is ready for use SETTING WATER HARDNESS The DESCALE message is displayed after a period of time established according to water hardness The machine is factory set for a hardness value of 4 very hard water The machine can also be programmed according to the actual hardness of the tap water in the various regions varying the frequency with which the message is displayed soft water TANTA e slightly hard water YTI 00 10 11 12 13 hard water 000 EEE very hard water 9009 BEEE Measuring water hardness 1 Remove the TOTAL HARDNESS TEST indicator paper from its pack 2 Immerse the paper completely in a glass of water for about a second 3 Remove the paper from the water and shake lightly After about a minute 1 2 3 or 4 red squares form depending on the hardness of the water Each square corresponds to one level 20 Setting water hardness 1 Press the P icon to enter the programming menu 2 Press the lt q or icon and select Water hardness 3 Confirm the selection by pressing the OK icon 4 Press the 4 or icon to set the number of squares formed on the reactive strip see figure in the previous section 5 Press the OK icon to confirm the setting 6 Press the ESC icon to exit the menu The machine is now reprogrammed with the new water hardness setting USING CO
7. Of burns Failure to observe the warning could result in scalds or burns Information This symbol identifies important advice or information for the user Letters in brackets The letters in brackets refer to the legend in the description of the appliance on page 3 Troubleshooting and repairs In the event of problems first try and resolve them following the information given in the Sections Displayed messages on page 21 and Troubleshooting on page 23 If this does not resolve the problem or you require further information you should consult Customer Service by calling the number given on the Customer Service sheet If your country is not among those listed on the Sheet call the number given in the guarantee lf repairs are required contact De Longhi customer services only The addresses are given in the warranty certificate provided with the machine DESCRIPTION Description of appliance page 3 LA A1 Grinding coarseness regulator knob A2 Container for coffee beans A3 Main switch some models only A4 Bean container lid A5 Cover for pre ground coffee funnel A6 Measuring scoop compartment A7 Cup warmer shelf A8 Ground coffee funnel A9 Display A10 Touch screen control panel A11 Hot water and steam nozzle A12 Brew group A13 Water tank A14 Power cable A15 Cup tray A16 Drip tray A17 Compartment for latte glass A18 Grounds tray A19 Service door A20 Coffe
8. prepare milk as described below 1 Remove the milk Spout and intake tube 2 Remove the Spout selector by pulling it Milk intake outwards tube 3 Wash all the components thoroughly with hot water and mild dish soap All components can be washed in a dishwasher placing them in the top basket of the dishwasher Hole Make sure there Hole are no milk residues left inside the holes and the groove on the fine end of the selector 4 Check that the intake tube and spout are not clogged with milk residues 5 Replace the selector milk spout and intake tube 6 Replace the lid on the milk container turning it counterclockwise to hook it in place 19 DESCALING Descale the machine when the message DESCALE flashes on the LCD display Important Descaler contains acids which may irritate the skin and eyes It is vital to adhere to the manufacturers safety warnings given on the descaler pack and the warnings relating to the procedure to follow in the event of contact with the skin and eyes Information Use De Longhi recommended descaler only Under no circumstances should you use sulphamic or acetic based descalers Their use invalidates the warranty Failure to descale the appliance as described above also invalidates the warranty 1 Turn the machine on 2 Enter the programming menu by pressing the P icon 3 Press the e or icon until Descaling is displayed 4
9. should not require regulating initially However if after making the first few coffees you find that delivery is either too fast or too Slow a drop at a time this can be corrected by regulating the grinding adjustment knob fig 11 ZN important The grinding coarseness regulator must only be turned when the coffee mill is in operation when you hear the grinder in motion For slower coffee delivery 17 anda creamier coffee turn one click towards 1 finer ground coffee pO S For more rapid coffee deliv ery not in drops turn one D 7 click towards 7 coarser ground coffee Information These adjustments will only be evident after at least two cups of coffee have been made 14 Making espresso coffee using coffee beans Important Do not use caramelized or candied coffee beans as they could stick to the coffee mill and make it unusable 1 Fill the container with coffee beans fig 12 2 Place under the coffee spouts one cup if you want one coffee fig 13 two cups if you want two coffees fig 14 3 Lower the spouts as near as possible to the cup This makes a creamier coffee fig 15 4 Choose the strength by hitting the do and size by hitting the z 9 Press the icon corresponding to the number of coffees required one cup 2 or two cups fig 9 and 16 6 Preparation begins A progress bar appears on the display and gradually advances as t
10. time you need to make 4 5 cups of coffee and 4 5 cappuccinos before the appliance Starts to give satisfactory results 11 TURNING THE APPLIANCE ON Information in models provided with main Switch before turning the appliance on make Sure the main switch on the back of the appliance is in the position fig 1 Each time the appliance is turned on it performs an automatic preheat and rinse cycle which cannot be interrupted The appliance is ready for use only after completion of this cycle Danger of burns During rinsing a little hot water comes out of the coffee spouts and is collected in the drip tray underneath Avoid contact with splashes of water e To turn the appliance on press the button on the left side of the machine d fig 5 the message Heating up please wait is displayed When heating is complete the message changes to Rinsing As well as heating the boiler this also heats the internal circuits by circulating hot water The appliance is at temperature when the message STANDARD COFFEE standard taste is displayed TURNING THE APPLIANCE OFF Each time the appliance is turned off it performs an automatic rinse cycle which cannot be interrupted Danger of burns During rinsing a little hot water flows from the coffee spouts Avoid contact with splashes of water To turn the appliance off press the button fig 5 The appliance performs the rinse cycle
11. 6 Press the ESC icon to exit the menu Setting auto off Information The appliance is set to switch automatically to stand by if not used for 30 minutes The time can be changed so that the appliance switches off after 1 or 2 hours 1 Press the P icon to enter the menu 2 Press the or icon until Auto off is displayed 3 Press the OK icon 4 Press the or icon until the required number of hours of operation 30 minutes 1 or 2 hours is displayed 5 Press the OK icon to confirm or the ESC icon to cancel the operation 6 Press the ESC icon to exit the menu Resetting default values reset This resets all menu settings and programmed quantities back to the default values with the exception of the language time and beep which remains as set as well as the counter for the Statistics function 1 Press the P icon to enter the menu 2 Press the e or icon until Default values is displayed 3 Press the OK icon 4 The message Confirm is displayed 5 Press the OK icon to confirm and exit or the ESC icon to cancel the operation Statistics function This displays statistics relating to the machine To display proceed as follows 1 Press the P icon to enter the menu 2 Press the or icon until Statistics is displayed Press the OK icon By pressing the lt q or icon you can check how many coffees have been made how many drinks with milk have bee
12. MPARTMENT FOR LATTE GLASS To accommodate larger latte cups under the cof fee spouts lift compartment door A17 towards machine and place glass in compartment DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY FILL TANK e The water tank is empty or positioned e Fill the tank with water and or insert it incorrectly correctly pushing it as far as it will go GROUND TOO FINE e The grinding is too fine and the coffee is Make the coffee again and turn the ADJUST MILL delivered too slowly grinding adjustment knob one click clockwise towards 7 while the coffee Insert water spout and mill is in operation The effect is only press OK visible after delivering two coffees e The machine cannot make coffee as e Press the OK icon to deliver water from there is air in the hydraulic circuit the spout until it flows out normally INSERT WATER e The water spout is not inserted or is e Insert water spout as far as it will go SPOUT inserted incorrectly EMPTY GROUNDS e The grounds container is too full or e Empty the grounds container and clean more than 3 days have passed since you then replace CONTAINER last made coffee this guarantees correct Important when removing the drip tray hygiene of the machine the grounds container MUST be emptied even if it is not completely full If this is not done when you make the next coffees the grounds container may fill up more than expected and clog the machine INSERT GROUNDS e Afte
13. Select by pressing the OK icon Descaling Confirm is displayed Press OK to activate the function 5 The message Add descaler Confirm is displayed 6 Before confirming empty the water tank A13 Pour the descaler diluted with water respecting the proportions indicated on the descaler bottle into the water tank Place an empty container with a minimum capacity of 50 oz 1 5 L under the hot water Spout Important Danger di of burns Hot water containing descaler flows out of the hot water spout Avoid contact with splashes of water 7 Confirm by pressing the OK icon 8 The message Descaling Underway is displayed The descaling program starts and the descaler liquid comes out of the water spout The descale program automatically performs a series of rinses and pauses to remove limescale deposits from inside the machine After about 30 minutes the message Rinsing FILL TANK is displayed I 9 The appliance is now ready for rinsing through with clean water Remove the water tank empty rinse under running water fill with clean water and replace Rinsing Press OK is displayed Empty the container used to collect the descaler solution and replace it under the hot water spout Press the OK icon to start rinsing Hot water flows out of the spout and the message Rinsing is displayed When the water tank is completely empty the message Rinsing complete Press
14. cercanos a usted Solamente en los Estados Unidos y Canada Registra questo prodotto on line per ricevere una copia omaggio della rivista Cook s Illustrated Visita www delonghiregistration com Visita www delonghiusa com per una lista dei centri di servizio a te piu vicini Solo negli Stati Uniti e Canada Electronic Characteristics Caract ristiques lectriques Caracteristicas electricas Caratteristiche elettriche 120V 60HZ 1350W RERLT ESPRESSI LONG P O GE ITALIAN LATTE carruccino MACCHIATO HOT MILK INDEX 17 POD AN AMON une 17 IMPORTANT SAFEGUARDS 8 Changing the quantity 17 SHORT CORD INSTRUCTIONS 8 17 Cleaning the coffee maker 17 INTRODUCTION TI 3 Cleaning the coffee grounds container 17 symbols used in these instructions 9 Cleaning the drip 18 Letters in brackets 9 Cleaning the water tank 18 Troubleshooting and repairs 9 Cleaning the coffee nozzles 18 9 Cleaning the pre ground coffee feed funnel 18 Description of appliance
15. e is factory preset to automatically deliver standard quantities To change these quantities proceed as follows 1 Place a cup under the coffee spouts and milk spout 2 Press the icon corresponding to the function you want to program LATTE CAPPUCCINO ITALIAN MACCHIATO or HOT MILK until Milk for Program quantity appears on the display and the icon corresponding to the selected function flashes 3 Release the icon The appliance starts delivering milk 4 When the required quantity of milk has been delivered into the cup press the icon again 5 After a few seconds the appliance starts delivering coffee into the cup and the message Coffee for Program quantity is displayed with the exception of the HOT MILK function and the Vicon flashes 6 As soon as the coffee in the cup reaches the required level press the icon Coffee delivery stops The machine is now reprogrammed with the new quantities HOT WATER gt Preparation Important Danger of burns Never leave the machine unsupervised while delivering hot water The hot water spout becomes hot while water is being delivered and must be held by the handle only 1 Make sure the hot water spout is attached correctly fig 4 2 Place a container under the spout as close as possible to avoid splashes 3 Press the f icon fig 34 The message Rinsing Hot water is displayed 4 Press the icon to select the
16. e spout adjustable height A21 Coffee guide A22 ON STAND BY button A23 Hot water spout A24 Coffee scoop Description of milk container page 3 8 B1 Milk frother selector B2 Milk container handle B3 CLEAN button B4 Milk intake tube B5 Frothed milk spout B6 Lid for milk frother Description of control panel touch screen page 3 0 Information Only the icons relating to the controls enabled for the particular function currently being used will be lit on the touch screen C1 Display guides the user in using the appliance C2 pm icon to scroll forwards through the programming menu C3 amp icon to deliver one cup of espresso coffee C4 SZ icon to deliver one cup of espresso coffee OK icon to enable and confirm the selected function C6 icon to rinse or deliver hot water C7 Hot MILK icon to deliver a cup of steamed milk ITALIAN MACCHIATO icon to deliver a Shot of espresso with a small amount of foam on top C9 LONG PP icon to deliver one cup of C10 CAPPUCCINO icon to deliver a Cappuccino C11 LATTE icon to deliver a latte C12 P icon to access the programming menu C13 ESC icon to exit the selected function in the menu C14 ee icon to select the coffee s strength C15 w icon to select the coffee size C16 amp icon to scroll backwards through the programming menu Co C8 Information A light touch is enough to activate the icon
17. ed showing the level of water it contains fig 37 Before the indicator protrudes from the cup tray the drip tray must be emptied and cleaned To remove the tray 1 Open the service door fig 35 2 Remove the drip tray and the grounds container Fig 36 3 Empty the drip tray and grounds container A18 and wash them 4 Replace the drip tray complete with grounds container A18 5 Close the service door Cleaning the water tank 1 Glean the water tank A13 regularly about once a month with a damp cloth and a little mild dish soap 2 Clean to remove all soap residues then rinse the water tank thoroughly Cleaning the coffee nozzles 1 Clean the nozzle periodically using a sponge or cloth fig 38 2 Check regularly that the holes in the coffee Spout are not blocked If necessary remove coffee deposits with a toothpick fig 39 Cleaning the pre ground coffee feed funnel e Check regularly about once a month that the pre ground coffee funnel is not blocked If necessary remove coffee deposits with a dull knife Danger of electric shock Before perform ing any cleaning operations the machine must be turned off and disconnected from the main power supply Never immerse the coffee maker in water 18 Cleaning the inside of the machine 1 Check regularly about once a week that the inside of the machine is not dirty If neces Sary remove coffee deposits with a dull knife and sponge
18. ed warranty with De Longhi Some states do not allow limitations on how long an implied warranty lasts so the above exclusions may not apply to you De Longhi does not authorize any other person or company to assume for it any liability in connection with the sale or use of its appliance How does state law apply This warranty gives you specific legal rights and you may also have other rights which vary from state to state 24
19. f the coffee by pressing the 2 icon Making cappuccino 1 After attaching the milk container place frothed milk regulator B1 on lid to position 2 for CAPPUCCINO fig 28 The quantity of froth can be adjusted by moving the regulator towards number 2 for a denser froth Moving it towards number 1 obtains a less dense froth 2 Press the CAPPUCCINO icon fig 29 The message Cappuccino Jug selector in position 2 appears After a few seconds frothed milk flows out of the milk spout into the cup below The milk will stop automatically and delivery of coffee will begin Information during delivery you want to Stop preparing milk press the CAPPUCCINO icon or interrupt preparation of the coffee by pressing the Z icon Making Italian macchiato 1 After attaching the milk container place frothed milk regulator B1 on lid to position 2 for ITALIAN MACCHIATO fig 28 2 Press the ITALIAN MACCHIATO icon fig 30 The message Macchiato Jug selector in position 2 appears After a few seconds frothed milk flows out of the milk spout into the cup below The milk will stop automatically and delivery of coffee will begin Information f during delivery you want to stop preparing milk press the ITALIAN MACCHIATO icon or interrupt preparation of the coffee by pressing the 2 icon Making hot milk 1 After attaching the milk container position the frothed milk regulator B1 according to the
20. finely e Turn the grinding adjustment knob one click clockwise towards 7 while too slowly or a drop at the coffee mill is in operation fig 11 a time Continue one click at a time until coffee delivery is satisfactory The effect is only visible after delivering two coffees The coffee is delivered The coffee is ground too coarsely e Avoid turning the grinding coarseness regulator excessively otherwise when too quickly you select two cups the coffee may be delivered a drop at a time The effect is only visible after delivering two coffees Coffee does not come e The spouts are blocked e Clean the spouts with a toothpick fig out of one of the 39 Spouts The coffee does not The holes in the spouts are clogged with Clean the spouts with a toothpick come out of the spouts dry coffee dust sponge or hard bristled kitchen brush but from around the e The coffee guide A21 inside the service Thoroughly clean the coffee guide service door 9 door is blocked and cannot swing A21 particularly near the hinges PROBLEM POSSIBLE CAUSE REMEDY The milk contains e The milk is not cold enough or is not e You should ideally use skimmed or semi semi skimmed skimmed milk at refrigerator temperature bubbles or squirts out about 41 F of the milk spout If the result is still disappointing try another brand of milk e The milk frother selector is incorrectly e Adjust following the instructions in t
21. ged cord or plug or after the appliance malfunctions or has been damaged in any manner Return the appliance to the nearest authorized service facility for examination repair or adjustment The use of accessory attachments not recommended by the manufacturer may result in fire electrical shock or personal injury Do not use outdoors Make sure the power cord does not hang over the edge of the table or counter top to avoid getting accidentally caught or entangled Do not place the appliance or its electrical parts on or near electric stoves cooking surfa ces or gas burners Plug cord into the wall outlet To disconnect first turn machine off then remove plug from wall outlet Do not use the appliance for other than the intended use This appliance is to be utilized for domestic use only The manufacturer declines all responsibility for any damage caused by improper incorrect or irresponsible use WARNING To reduce the risk of fire or electric shock do not remove the cover or the exterior of the unit Don t attempt to repair or modify the machine doing so will void the warranty Repair should be done by authorized service personnel only SAVE THESE INSTRUCTIONS THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY A short power cord is provided to reduce risks resulting from becoming entangled in or tripping over a longer cord Longer detachable power supply cords or extension cords are available and may be used if care is exercised in
22. he adjusted section on preparing drinks with milk e The milk container lid is dirty e Clean the milk container lid as described in the section Cleaning the milk container The appliance does not Itis not plugged into the power outlet e Plug into the power outlet come on The LONG coffee has The coffee is ground too fine Turn the grinding adjustment knob one click clockwise towards 7 while the coffee mill is in operation fig 11 Continue one click at a time until coffee delivery is satisfactory The effect is only visible after delivering two coffees too much froth 23 This warranty applies to Super Automatic Espresso Machines with the De Longhi brand name LIMITED WARRANTY gt gt What does the warranty cover We warrant each appliance to be free from defects in material and workmanship Our obligation under this warranty is limited to repair at our factory or authorized service center of any defective parts or part thereof other than parts damaged in transit The repaired or new model will be returned at the company expense This warranty shall apply only if the appliance is used in accordance with the factory directions which accompany it and on an alternating current AC circuit How long does the coverage last This warranty runs for two years 2 from the purchase date found on your receipt and applies only to the original purchaser for use What is not covered by the warranty
23. he procedure progresses fig 17 Once the coffee has been made the appliance is ready to use again Information e While the machine is making coffee delivery can be interrupted at any moment by pressing the lit cup icon e Fora hotter coffee before delivery rinse the appliance through by pressing the icon and confirming with the OK icon HoT water flows out of the coffee spouts and heats the internal circuit of the machine so that the coffee delivered will be hotter e For an even hotter coffee heat the cups by rinsing them with the hot water e fthe coffee is delivered in drops too fast and not creamy enough or too cold read the tips in the Troubleshooting section on page 22 Making long coffee using coffee beans Information When this function is activated a long coffee similar to drip coffee is obtained Important Do not use caramelized or candied coffee beans as they could stick to the coffee mill and make it unusable 1 Fill the container with coffee beans fig 12 2 Adjust the height of the spout according to the cup used Put the cup for long coffee under the spouts fig 18 3 Choose the strength by hitting the Dg and size by hitting the mw 4 Press the LONG icon fig 10 Preparation begins A progress bar appears on the display and gradually advances as the procedure progresses o information While the machine is making coffee delivery can be interrupted at any
24. i superautomatic coffee makers you need not use chemical products to clean the machine The descaler recommended by De Longhi is made from natural and completely biodegradable substances e None of the components of the appliance can be washed in a dishwasher with the exception of the milk container B e Do not use metal objects to remove encrustations or coffee deposits as they could scratch metal or plastic surfaces Cleaning the coffee grounds container When EMPTY GROUNDS CONTAINER is displayed the grounds container must be emptied and cleaned Until the grounds container has been cleaned the appliance continues to display the message and coffee cannot be made To clean e open the service door on the front of the appliance fig 35 extract the drip tray fig 36 empty and clean e Empty the grounds container A18 and clean thoroughly to remove all residues left on the bottom Important when removing the drip tray the grounds container must be emptied even if it is not completely full If this is not done when you make the next coffees the grounds container may fill up more than expected and clog the machine Cleaning the drip tray Important f the drip tray is not emptied regularly the water could overflow from the edge and seep inside or around the machine This could damage the machine the surface it rests on or the surrounding area The drip tray is fitted with a level indicator r
25. inside of the appliance thoroughly as described in the section Cleaning the inside of the machine If the message is still displayed after cleaning contact customer services PRESS CLEAN Milk has been delivered recently and the Press the CLEAN button and keep it BUTTON tubes inside the milk container must be pressed until the progress bar which cleaned appears on the display together with the message Cleaning is complete ADD PRE GROUND The appliance is delivering a LONG Add a level measure of pre ground COFFEE coffee of more than 4 2 oz 125 ml coffee and confirm by pressing the OK PRESS OK a Below is a list of some of the possible malfunctions If the problem cannot be resolved as described contact customer service PROBLEM POSSIBLE CAUSE REMEDY water e The brew group has cooled down e Before making coffee rinse as described because 2 3 minutes have elapsed since in the notes in the section Preparing the last coffee was made coffee using coffee beans The coffee is not e The coffee is ground too coarsely e Turn the grinding adjustment knob one click counterclockwise towards 1 while creamy enough the coffee mill is in operation fig 11 Continue one click at a time until coffee delivery is satisfactory The effect is only visible after delivering two coffees e Wrong type of coffee e Usea type of coffee for espresso coffee makers The coffee is delivered The coffee is ground too
26. level marked on the handle fig 21 Information We recommend using skim or 2 milk at refrigerator temperature about 41 F To avoid milk with poor froth or large bubbles always clean the milk lid and hot water nozzle as described in the section Cleaning the milk container on page 19 3 Make sure the milk intake tube is correctly inserted in the bottom of the milk container lid fig 22 4 Replace the milk container lid and turn counterclockwise as far as it will go until you hear it click 5 Remove the hot water spout from the nozzle fig 23 6 Attach the container to the nozzle and push as far as it will go fig 24 The machine emits a beep when milk container is attached correctly if the beep function is enabled 7 Place a sufficiently large cup under the coffee spouts and frothed milk spout To use particularly tall cups glasses raise the lid A17 of the special compartment in the cup tray fig 25 Making latte 1 After attaching the milk container place frothed milk regulator B1 on lid to position 1 for LATTE fig 26 2 Press the LATTE icon fig 27 The message Caffelatte Jug selector in position 1 appears After a few seconds frothed milk is delivered from the milk Spout into the cup below The milk will stop automatically and delivery of coffee will begin Information f during delivery you want to stop preparing milk press the LATTE icon or interrupt preparation o
27. m De Longhi America Inc Park 80 West Plaza One Saddle Brook NJ 07663 1 866 528 8323 1 866 Latte Best De Longhi Canada Inc 6150 McLaughlin Road Mississauga Ontario L5R 4E1 Canada 1 888 335 6644 Fiducia Italiana S A de C V Pestalozzi 814 Col Del Valle Del Benito Juarez M xico D F 03100 1447 y 5543 6492 to 01800 711 8805 5713212301 07 09 Instructions for use Keep these instructions Mode d emploi Conservez cette notice Instrucciones para el uso Repase y guarde estas instrucciones Lea cuidadosamente este instructivo antes de usar su aparato Istruzioni per l uso Leggere e conservare queste istruzioni FULLY AUTOMATIC COFFEE CENTER MACHINE CAF AUTOMATIQUE CAFETERA SUPERAUTOMATICA MACCHINA PER CAFF SUPERAUTOMATICA ESAM6700 Register this product on line and receive a free trial issue of Cook s Illustrated Visit www delonghiregistration com Visit www delonghiusa com for a list of service centers near you U S and Canada Only Enregistrez ce produit en ligne et recevez un num ro gratuit de Cook s Illustrated Visitez www delonghiregistration com Visitez www delonghiusa com pour y voir une liste des centres de reparation proches de chez vous E U et Canada uniquement Registre este producto en linea y reciba un ejemplar gratis de Cook s Illustrated Visite www delonghire gistration com Visite www delonghiusa com para ver la lista de centros de servicios
28. moment by pressing the LONG icon e Only one cup of long coffee can be made ata time e When delivering more than 4 2 oz the appliance automatically grinds more coffee halfway through delivery Making espresso or long coffee using pre ground coffee A Important Never add pre ground coffee when the machine is off or it could spread through the inside of the machine and dirty it e Never use more than one level measuring scoop or it could dirty the inside of the machine or block the funnel Information f you use pre ground coffee you can only make one cup of coffee at a time 1 Press the do icon repeatedly fig 7 until Pre ground flashes on the display 2 Putone level measuring scoop of pre ground coffee into the funnel fig 19 3 Place a cup under the coffee spouts 4 To make espresso coffee press the one cup Y icon fig 9 To make a long coffee press the LONG icon fig 10 Information LONG COFFEE when deliver ing more than 4 2 oz the appliance requests a new level measure of pre ground coffee halfway through delivery When you have added the pre ground coffee confirm by pressing the OK icon 15 MAKING DRINKS WITH MILK Filling and attaching the milk container 1 Turn the lid of the milk container clockwise until it becomes noticeably difficult to turn then remove the lid fig 20 2 Fill the milk container with a sufficient quantity of milk not exceeding the MAX
29. n made how many times the machine has been descaled the total number of liters of water delivered 5 Press the ESC icon twice to exit the menu m p9 Acoustic signal Beep enabled This activates or deactivates the beep emitted by the machine each time an icon is pressed or an accessory is inserted removed The beep is enabled by default 1 Press the P icon to enter the menu 2 Press the or icon until Beep enabled is displayed 3 Press the OK icon to confirm Confirm is displayed 4 Press the OK icon again to confirm activation or the ESC icon to deactivate the function 5 Press the ESC icon to exit the menu Information The descale and water hard ness functions will be explained later in the manual 13 MAKING COFFEE Selecting the coffee taste The appliance is preset to make coffee with a standard taste You can choose between 5 different coffee tastes Extra mild taste Mild taste standard taste Strong taste Extra strong taste To change the flavor press the 1 7 icon fig 7 repeatedly until the required taste is displayed Selecting the quantity of coffee in the cup To select the quantity of coffee press the gt icon repeatedly fig 8 until the required quantity of coffee is displayed The quantities delivered are different according to the type of coffee Selected ESPRESSO LONG oz COFFEE 0z COFFEE 2 6 i Programming the espres
30. ogramming menu 2 Press the or icon until Auto start disabled is displayed Enable is displayed and the hours flash on the display 3 Press the OK icon the hours flash on the display 4 Press the or icon to change the hours 12 5 Press the OK icon to confirm the minutes flash on the display 6 Press the or minutes 7 Press the OK icon to confirm Auto start Enabled is displayed 8 Press the ESC icon to exit the menu a symbol appears next to the clock to indicate that auto start has been programmed To deactivate the function 1 Press the P icon to enter the programming menu 2 Press the or icon until Auto start Enabled is displayed 3 Press the OK icon the hours flash on the display 4 Press the ESC icon This deactivates the function and the 8 symbol disappears from the display 5 Press the ESC icon to exit the menu icon to change the Information lo activate this function the time must have been set previously Setting the temperature To modify the temperature low medium high of the water used to make the coffee proceed as follows 1 Press the P icon to enter the menu 2 Press the lt or icon until Temperature is displayed 3 Press the OK icon 4 Press the or icon until the required temperature low medium or high is displayed 5 Press the OK icon to confirm or the ESC icon to cancel the operation
31. quantity of froth you require pos 1 little froth pos 2 abundant froth 2 Press the HOT MILK icon fig 31 HOT MILK appears on the display and after a few seconds frothed milk is delivered from the milk spout into the cup below Delivery of milk stops automatically Information f during delivery you want to Stop preparing milk press the HOT MILK icon once 16 Cleaning the milk container after use Important Danger of burns When cleaning the internal tubes of the milk container a little hot water comes out of the frothed milk tube B5 Avoid contact with splashes of water When Press CLEAN button flashes on the display each time you use a milk function 1 Leave the jug attached to the machine you do not need to empty it 2 Place a cup or other recipient under the frothed milk spout 3 Press the CLEAN button fig 32 and keep pressing until the progress bar which appears on the display together with the message Cleaning is complete 4 Remove the milk container and always clean the nozzle with a sponge fig 33 o information When Press CLEAN button flashes on the display you can still prepare any type of coffee or milk If you have to make a number of drinks with milk wait until you have delivered the last cup before cleaning the container e The milk left in the jug can be kept in the refrigerator Programming the size for each beverage button The applianc
32. r cleaning the grounds container e Open the service door and insert the CONTAINER has not been replaced grounds container If grounds container is inside the machine and message is still displayed there may be a damaged mircoswitch and customer service should be called INSERT MILK e The milk container is not inserted e Insert milk container as far as it will go CONTAINER DESCALE e The machine must be descaled e The descaling procedure described in the Descaling section needs to be performed as soon as possible LESS COFFEE e Too much ground coffee has been used Selecta milder taste or reduce the quantity of pre ground coffee then make the coffee again ADD PRE GROUND e The pre ground coffee function has e Place pre ground coffee in the funnel COFFEE been selected without placing any pre l ground coffee in the funnel e The funnel is blocked e Empty the funnel with the help of a dull knife as described in the section Cleaning the pre ground coffee feed funnel FILL BEANS e The coffee beans have run out e Fill bean container CONTAINER INSERT BREW GROUP The brew group has not been replaced e Insert the brew group as described in the ASSEMBLY after cleaning section Cleaning the brew group CLOSE DOOR e The service door is open e Close the service door 21 DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY GENERAL ALARM e The inside of the appliance is very dirty Clean the
33. so my coffee quantity The appliance is set by default to automatically deliver 1 oz of espresso coffee To modify this quantity proceed as follows 1 Press the w icon repeatedly fig 8 until MY COFFEE is displayed 2 Press and hold the one cup amp icon fig 9 for about 8 seconds until Program quantity is displayed then release The machine Starts delivering the coffee and the amp icon flashes 3 As soon as the coffee in the cup reaches the LONG COFFEE EXTRA LONG COFFEE STANDARD COFFEE required level press the amp icon again The quantity set has now been programmed Information This setting is valid for mak ing both one and two cups You cannot program a quantity for two cups To obtain 2 quantities of my coffee press the button Programming the long my coffee quantity The appliance is set by default to automatically deliver 3 4 oz of LONG coffee To modify this quantity proceed as follows 1 Press the icon repeatedly fig 8 until MY COFFEE is displayed 2 Press the LONG IP icon fig 10 until Pro gram quantity is displayed then release The machine starts delivering the coffee and the LONG icon flashes 3 As soon as the coffee in the cup reaches the required level press the LONG icon again The quantity set has now been programmed Regulating the coffee mill The coffee mill is preset in the factory to prepare coffee correctly and
34. te 13 Selecting the guantity of coffee in the cup 13 BP EOS 19 LONG COFFEE BZ uses 13 Programming the espresso my coffee QUAND o ea 13 Programming the long my coffee guantity 14 Regulating the coffee mill 14 Making espresso coffee using coffee beans 14 Making long coffee using coffee beans 14 Making espresso or long coffee using pre ground A 15 MAKING DRINKS WITH MILK 15 Filling and attaching the milk container 15 ia zaznan 15 Making cappuccino une 16 Making Italian macchiato 16 Making hot Milk ae 16 Cleaning the milk container after use 16 Programming the size for each beverage DO ON ee ee 16 IMPORTANT SAFE ARD When using electrical appliances basic safety precautions should always be followed inclu ding the following Read all instructions carefully Make sure the voltage of your electrical system corresponds to the voltage shown on the bottom of the machine Do not touch hot surfaces Use handles or knobs To protect against fire electrical shock and personal injury do not immerse cord plug or appliance in water or other liquid Keep the appliance out of the reach of children and do not leave appliance unattended while in operation Unplug from the outlet when not in use and before cleaning Do not operate with a dama
35. the appliance Information e Coffee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coffee in the mill The machine is however guaranteed to be new e You should customize water hardness as soon as possible following the instructions in the section Setting water hardness on page 20 1 Plug the appliance into the power outlet and in models provided with main switch place the main switch on the back of the appliance in the position fig 1 You must first select the language the languages scroll through at intervals of about two seconds 2 When English appears press the OK icon for 3 seconds fig 2 Once the language has been saved the message English installed is displayed Follow the instructions appliance 3 FILL TANKI remove the water tank fill to the MAX line with fresh water then replace in the appliance fig 3 4 INSERT WATER SPOUT AND PRESS OK Check that the hot water spout is inserted on the nozzle and place a container underneath fig 4 Press the OK icon fig 2 PLEASE WAIT is displayed and the appliance begins to deliver hot water The appliance ends the first start up procedure then the message Turning off please wait is displayed and the appliance goes off The coffee maker is now ready for normal use indicated by the Information When using the appliance for the first
36. their use f an extension cord is used the marked electrical rating should be at least as great as the electrical rating of the appliance If the appliance is provided with 3 wire grounding type cord the extension Should be a GROUNDING TYPE 3 WIRE CORD The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over Your product is equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug 8 INTRODUCTION o Thankyou for choosing the ESAM 6700 automatic coffee and cappuccino maker We hope you enjoy using your new appliance Take a few minutes to read these instructions This will avoid all risks and damage to the machine Symbols used in these instructions Important warnings are identified by these symbols These warnings must absolutely be respected Danger Failure to observe the warning could result in possibly life threatening injury from electric shock Important Failure to observe the warning could result in injury or damage to the appliance Danger
37. then goes off Information In models provided with main switch if the appliance is not used for an extended period place the main switch on the back of the appliance in the 0 position fig 6 CHANGING THE MENU SETTINGS __ Setting the language To modify the language on the display proceed as follows 1 Press the P icon to enter the programming menu 2 Press the lt q or icon until Set language is displayed 3 Press the OK icon 4 Press the amp or icon until the required language is displayed 5 Press the OK icon to confirm or the ESC icon to cancel the operation 6 Press the ESC icon to exit the menu Setting the clock To adjust the time on the display proceed as follows 1 Press the P icon to enter the programming menu 2 Press the lt or icon until Adjust time is displayed 3 Press the OK icon the hours flash on the display 4 Press the or icon to change the hours 5 Press the OK icon to confirm or the ESC icon to cancel the operation the minutes flash on the display 6 Press the or icon to change the minutes 7 Press the OK icon to confirm or the ESC icon to cancel the operation 8 Press the ESC icon to exit the programming menu Setting auto start time You can set the auto start time in order to have the appliance ready at a certain time for example in the morning so you can make coffee immediately 1 Press the P icon to enter the pr
Download Pdf Manuals
Related Search