Home

User manual

image

Contents

1. EE 748 5027 F 1519 748 1543 broussel thermopatch com Feb2014
2. NL 27 V 1 2 ENG QC TDPT mn fh February 2014 6 Operating instruction 6 1 USAGE It is recommended to read carefully the instruction manual before you start any pressing operation Before starting any heat sealing jobs please take note of this manual The heat seal press should be operated by a qualified person who has been informed of the risks of working with heat seal equipment Be careful not to put irregular shaped thick or sharp objects under the press such as zippers buttons paperclips or staples These will damage the teflon sheet protecting the heating element and the press cushion on the lower platen 6 2 CONTROL PANEL Selection key LED Indicato Temp LED Indicator Time 8 www thermopatch biz Thermopatch POWER ON Switch the NL 27 on with the ON OFF switch mounted on the back After switching the machine on the display shows the set temperature TEMPERATURE SETTINGS Push the selection key twice 2x for temperature setting thermometer symbol after which the LED indicator lights up Push the Up Arrow upward key to increase the temperature Push the Down arrow downward key to decrease the temperature TIME SETTINGS Push the selection key once 1x for setting the time hourglass symbol after which the LED indicator lights up Push the Up Arrow upward key to increase the time Push the Down arrow downward key to decrease the time 11 PRESSURE ADJ USTMENT The pr
3. your Thermopatch supplier 12 Conditions of warranty Thermopatch points to its warranty and product liability conditions as laid down in our conditions of sales These can be obtained at your Thermopatch supplier 2 Intended use The pneumatic NL 27 is a heat seal machine that is especially intended for the application of heat sealable transfers But all Thermopatch marking and mending materials can be applied with the NL 27 Z WARNING Any use other than described above can be dangerous and cause damage and thus qualifies as misuse which excludes Thermopatch bv from any liability thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 3 Technical specifications 3 1 Specifications of the NL 27 NL 27 Power Power supply Operating temperature Temperature range Press Time range Discharge pressure range Machine height open Machine width Machine depth Gross weight including packaging Net weight Size sealing pads round Fuses 2500 Watts 230 Volt z250 C 0 250 C 0 9 min 59sec O 0 3 kg cm 460 mm 453 mm 753 mm 70 kg 40 kg 160 mm 2x TLOAL 230V 4 Overview of safety measures and warnings 4 1 Safety No specific safety measures were provided for this machine Warning symbols The following warning symbols have been mounted onto the machine for added safety Z WARNING A
4. Hot surface Z WARNING A Electric tension ATTENTION Make sure you are informed about the contents of this manual before starting to work with the NL 27 This ensures an optimal and safe use of the machine ATTENTION Always turn the power off unplug it when you need to carry out maintenance work or when cleaning the machine ATTENTION Take care that there is enough space around the machine Cables and connections must not get pinched Although the heat radiation of the press is low there should be enough space for cooling down ATTENTION Avoid contact with the press cover and the heating element O ATTENTION Pull the fabrics tight around the press pad and ensure that your hands are away from the sealing pad before operating the machine thermopatch com C ATTENTION Hold the handle while opening the machine after finishing the sealing cycle The handle will come up forcefully when not guided manually Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 9 thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 5 Transport and storage 5 1 Transport When the machine needs to be moved Thermopatch advises to use the original packaging 5 2 Storage When the machine needs to be stored Thermopatch advises to use the original packaging The machine should be stored on a pallet off the floor in dry conditions 10 O O je O 4 142 o o E Sm o p Manual
5. PA27 009 Fuse T10Amp 20 x 5 mm SPA27 005 Heat Element Mica 2500 W 400 x 500 m thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 14 9 Technical annexes Image 01NL 27 Press handle Electromagnet Pressure adjustment wheel Control panel Heating plate Teflon cover sheet Power entry and On Off switch Silicone rubber cushion Lower platen thermopatch com ENG V 1 2 Feb 2014 Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 15 Drawing 02 Electrical wiring diagram sonde tem perature relais om5 Electromagnet Combi switch 220V F 16A Draaibrugweg 14 Nbre ENSD GD 1 ELECTRICAL WIRING nas cp DIAGRAM FAIT LE 19 02 09 DE DU PLANA ENSEMBLE NEZ7 IA thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 16 10 Faults Fault Heating plate does not heat up If a problem should occur 6 Thermopatch Since 1934 please consult the list below if the problem you are facing cannot be solved by yourselves contact your supplier Z WARNING All repair and maintenance operations should be done when the machine is turned off and unplugged from the main electric power supply Possible cause 1 One or both fuses are out of order 2 The relay is damaged 3 Sensor out of order and or regulator displays ER1 The heating element can cause burns The user mu
6. Thermopatch Since 1934 NL 27 Copyrights thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 2014 Thermopatch bv Almere The Netherlands No part of this publication may be reproduced by any means without the prior written permission of Thermopatch bv The Netherlands Thermopatch and the Thermopatch logo Thermoseal and Thermocrest are registered trademarks of Thermopatch Introduction Dear User Welcome to the growing group of Thermopatch users Your purchase has been manufactured with the utmost care to ensure that you benefit as long as possible from your Thermopatch product The products by Thermopatch are designed with special attention to your convenience Should you discover any fault or damage upon receipt of this product please contact your local Thermopatch vendor CO ATTENTION In order to make safe and optimal use of the NL 27 it is important to take note of and understand the contents of this manual thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 Contents thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 Copyrights Introduction Contents DECLARATION OF CONFORMITY 1 General description 1 1 Delivery 1 2 Conditions of warranty 2 Intended use 3 Technical specifications 3 1 Specifications of the NL 27 4 Overview of safety measures and warnings 4 1 Safety 5 Transport and storage 5 1 Transport 6 Op
7. allation thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 7 1 Installation of the NL 27 Unpack the machine from the box and install it safely on a suitable work table To move the press make sure it is cold and handle it by grabbing both plates upper and lower at the same time machine closed for lifting the machine Z WARNING Do not lift or transport the machine by the operating handle This will damage the machine and due to the force by the spring controlled handle injuries may occur Remove the bolt labelled Transport security before opening the press Take care that there is enough free space around the machine Also take care that there are no items near the machine that are sensitive to heat radiation 7 2 Electrical requirements Plug the machine electrically 230 Volt earthed 50 or 60 Hertz into a suitbable wall socket into the mains 13 8 Maintenance instructions 8 1 Daily maintenance Daily Clean the teflon cover of the heating plate with a dry cloth Depending on use e Change the silicon rubber as soon as it is damaged or if it has lost its properties e Grease the axels of the machine every 6 months 8 2 Parts for regular replacement for maintenance Article Num Description ber SPA27 001 SPA27 002 SPA27 003 SPA27 004 SPA27 006 Gas spring for NL27 SPA27 007 Teflon cover for heating element 400 x 500 mm SPA27 008 Silicone rubber 400 x 500 mm S
8. erating instruction 7 Installation 7 1 Installation of the NL 27 8 Maintenance instructions 8 1 Daily maintenance 9 Technical annexes Image 01 NL 27 Drawing 02 Electrical wiring diagram 10 Faults 11 End of life O O O M DN AMO LI RK WN thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 DECLARATION OF CONFORMITY We Thermopatch B V Draaibrugweg 14 1332 Almere The Netherlands herewith declare on our own responsibility that the machinery Thermopatch Thermoseal NL 27 which this declaration refers to is in accordance with the conditions of the following Directive s 2006 95 EG Low voltage directive 2004 108 EG EMC directive The Netherlands Almere 12 02 2014 an Bausch Director thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 1 General description The NL 27 is a practical heat seal press for the application of textile labels company emblems repair patches transfers In short all Thermopatch materials for marking and repair can be easily and permanently pressed on all types of fabric 11Delivery The NL 27 is mounted onto a pallet covered with a wooden box The following articles can be found at e NL 27 heat seal machine Power cord e Quick installation guide e quality checklist e Manual on CD ROM e CE Declaration of Conformity can be found in this manual If one of these articles should be missing or faulty please contact
9. essure is obtained by bringing the upper hot plate to the lower cold plate together e Then unlock the knurled nut underneath the adjustment wheel Turn the wheel on top of the heating plate e clockwise to increase the pressure e anticlockwise to decrease it e Tighten the knurled nut to lock the pressure setting HEAT SEALING TRANSFERS e Turn on the machine by switching the power button e Adjust the desired temperature at 185 C or depending on the type of transfer See TEMPERATURE SETTINGS on page 11 e Adjust the time at 12 Sec or depending on the type of transfer See TIME SETTINGS on page 11 e Adjust the pressure depending on the type of transfer See PRESSURE ADJ USTMENT on page 12 above e Place the item for instance a T shirt on the lower cold plate e Add your transfer on top of it glue side downwards on the textile e Lower the heating plate using the handle once the plate has reached the desired temperature When the plate is in contact with the T shirt the timer starts At the end of the countdown the buzzer will ring Pull the heating plate up support the heating plate by the handle until fully risen Take the item off the press and peel the carrier off of the transfer after cooling down for a while e Re seal when necessary with the peeled off carrier replaced loose on top of the transfer thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 12 7 Inst
10. st ensure the temperature is below 25 C on the display before any intervention Solutions 1 When the display does not light up after switching on the NL 27 check the fuses en replace if nec essary The fuse is located in the power entry on the back of the machine 2 Check and replace when neces Sary 3 Replace the sensor Heating plate overheats 1 The relay is stuck 2 The card is damaged 1 Replace the relay 2 Replace the card Timer does not start 1 The microswitch is not acti vated 1 Correct by ensuring that the le ver of the microswitch touches the press arm The buzzer sounds con tinuously 1 The microswitch is stuck 1 loosen the microswitch or replace it thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 17 11 End of life Choose to dispose of the machine responsibly when it has reached its end of life Electrical machinery accessories and packaging should be recycled as much as possible in an environmentally responsible manner Dismantle the machine groups steel parts components electrical components These can be separated and returned for recycling CP ATTENTI ON Always dispose according to current and locally applied guidelines for health and safety and disposal requirements thermopatch com Manual NL 27 V 1 2 ENG QC TDPT mn fh February 2014 18 fo a thermopatc wA Airal ia Canada if il

Download Pdf Manuals

image

Related Search

Related Contents

  "取扱説明書"  AZURA UVD 2.1L user manual  Microlab FC-330 loudspeaker  manual for fwd testing in the long  basicXL BXL-FN12 fan  DOC TECHNIQUE ( 163 Ko)  folletos  KDL-37XBR6 - Mark Twain  ASUS B23E User's Manual  

Copyright © All rights reserved.
Failed to retrieve file