708 User Manual_20120724.ai
Contents
1. Bike Guard 708AA USER MANUAL a INTRODUCTION Bicycles are stolen everywhere and every day no matter they are with or without locks To protect your bicycle from being stolen our Digital RF wireless bicycle alarm system can be your best solution Once the bike theft happens the Bike Alarm will sound loud beeps to scare the thief away and the Beeper will also immediately activate an emergency alarm to warn you to check the bicycle and take the necessary actions urgently Therefore with Bike Guard 708AA armed on the bicycle whenever you want to take a short break in the cycling journey there is no need for you to worry about parking your bike nearby Product Description Base Unit Front Back lFinoateciment SSS lemeyso SSS Speaker srewioe O Bateyower SSS Product Description Model Name Function Cs rSC i TCC CA Wrt amp Search Re Battery Type CR2032 Battery Life Time on Standby Over 45 days 8 hrs day Beep Audible Level at 10 cm 3 9 inches Base unit 95 db Tag unit 102db 2 Base unit 61 5x36x11 6mm 2 42x1 42x0 46inch amen Tag unit 38x120x6 2mm 1 5x4 72x0 24inch Package Contents How to apply wear the Base and Tag units Model Name 708AA Base Unit Tag Unit Base Unit 1 pe Tag Unit 1 pc Batteries CR2032x2 Strap 1 Hook 1 User manual v Page 1 Bike Guard 708AA USER MANUAL 2 GETTING STARTED Out of range Alert This section shows how to q2. Base unit will begin to chirp and the Tag unit will begin to beep Press once and release When the bicycle is Beeps for 3 seconds Beeps for 3 seconds pai Shocked accidentally When the bicycle Continuously send out Continuously send out movement still beeps beeps continues When Base unit is Continuously send out long No beep sound power off destroyed or beeps the bicycle is hijacked When the bicycle can t be Continuously send out Green LED blinks located in the parking lot beeps press the Search button and When the battery is low Buzzer beeps once every 2 Buzzer beeps once every 2 minutes minutes Additional Search Function Information Out of range or Loss signal a Base unit beeps and signal LED blinks for 80 seconds out of range or loss signal then Base unit will enter sleep mode automatically b Base unit beeps once a minute to remind user to switch power OFF for Base unit for power saving c To wake up Master press Search button to go to wake up process Low battery When the Matser and Slave is under low battery condition it will beep at a 2 minutes interval please change the battery Important Under low battery condition it may cause abnormal function of alarm or searching Page 3 Bike Guard 708AA USER MANUAL 6 Warnings and Important Information 1 The Tag units are water repellent but not waterproof Keep the device dry Precipitation hum
3. 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This FCC Certifications equipment generates uses and can radiate radio frequency energy if installed and used not in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determinedly turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures m Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver m Connect the equipment into an outlet on a circuit different from that to which the receiver is connected m Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept an interference received including interference that may cause undesired operation FCC Caution Any changes or modifications are not expressly approved by the party responsible for compliance which could void the user s authority to operate this equipment EU Declaration Conformity This product is car
4. idity and all types of liquids or moisture can contain minerals that may corrode electronic circuits If your device gets wet remove the battery and allow the device to dry completely before replacing it 2 If you want to use the device during air flight please comply with the air safety regulations for each respective country 3 We reserve the right to change the hardware software specifications and designs as well as the information in the manuals at any time without prior notice 4 Proper operating temperatures for this product are between 14 F 140 F 10 C 60 C Proper Storage Temperatures are between 4 F 185 F 20 C 85 C 5 Under low battery charge conditions both Base and Tag will alert with a beep every 2 minutes in this case replace batteries immediately Low battery conditions may result in unpredictable product behavior such as low alert volume and false readings To save battery charge turn off both units when appropriate e g evenings at home 6 The Batteries provided in this product should be disposed of properly according to national or regional recycling regulations contact local authorities for more information Warning Do not expose the batteries to fire or heat this may result in danger from explosions a Certifications Federal Communication Commission Interference Statement This equipment has been tested and improved to comply with the limits of a Class B digital device pursuant to Part
5. rying the CE Mark in accordance with the related European Directives COD CEEA Page 4 91E 02B8 U50G20
6. uickly setup and trigger an alert condition 1 Insert the batteries into the Base unit and the Tag unit a Slide out remove the battery covers on the Base and Tag Units b Insert batteries included with the mark facing upward in the battery compartments c Replace the battery compartment covers on both units Base Unit Tag Unit On Off switch 2 Make sure that the Base and Tag units are in close proximity 3 Turn ON the Power switch on the Base units The base units will establish a link and begin to blink synchronously 4 Shock the Tag unit and the base will beep 5 Congratulations now you are ready to put the Tag unit underneath the bottle cage on a bike in case the alarm is triggeved while installation K y A sensor is bulit in to detect the vibration while someone is trying to move your bike the Bike Guard will alert you in 3 seconds The Base amp Tag unit will alarm for 5 seconds and repeat alarm until vibration is stop Disarm Alarm Under standby mode turn OFF the Master unit within 1 meters from your bicycle the Tag unit will sound Di du to approval disarm When you hear Di du you have disarmed Bike Guard Beep Beep Beep Beep Page 2 Bike Guard 708AA USER MANUAL 4 SEARCH When a tagged item is misplaced you can use the Base unit to search for it if it is within a 300 meters 984ft line of sight radius On the Base unit press the Search Set Button once The
Download Pdf Manuals
Related Search