未命名 -1 - Data
Contents
1. On is to turn on the wired siren Off is to turn off the wired siren Default setting is On the wired siren is on 36 Turn On Off Arm Disarm Beep for Wired Siren Log on the menu press 4 or 1 choose System Settings press Enter Press 4 or 1 choose Siren Setup press Enter Press J or choose Wired Siren press Enter Press J or 7 choose Arm Disarm Beep press Enter Press 4 or 1 choose On or Off press Enter On is to turn on arm disarm beep for wired siren Off is to turn off arm disarm beep for wired siren Default setting is On arm disarm beep is on Wireless Siren Wireless siren is connected to control panel through wireless connection Turn On Off Wireless Siren Log on the menu press 4 or choose System Settings press Enter Press J or T choose Siren Setup press Enter Press J or T Press 4 or 7 choose Siren On Off press Enter Press J or On is to turn on the wireless siren Off is to turn off the wireless siren choose Wireless Siren press Enter choose On or Off press Enter Default setting is On the wireless siren is on Turn On Off Arm Disarm Beep for Wireless Siren Log on the menu press 4 or 1 choose System Settings press Enter Press 4 or choo2. Press 4 or f choose Access Code press Enter Press J or 4 choose Admin Code press Enter LCD display will show Input 6 Digits then input 6 digits for code press Enter Default Admin Code 123456 Input the new admin code press Enter User Code With user code user can set arm home mode and disarm the alarm system Log on the menu press 4 or 7 choose System Settings press Enter Press J or f choose Access Code press Enter Press 4 or choose User Code press Enter LCD display will show Input 4 Digits then input 4 digits for code press Enter Default User Code 1234 Input the new user code press Enter Duress Code In case of emergency when user is violently requested to disarm the system it s recommended to use the duress code to disarm the alarm system The panel will silently dial alarm telephone numbers stored Log on the menu press J or choose System Settings press Enter 2 Press 4 or oe choose Access Code press Enter Press 4 or 1 choose Duress Code press Enter LCD display will show Input 4 Digits then input 4 digits for code press Enter Default Duress Code 1111 Input the new duress code press Enter Ringing Times for Remote Phone Control After the set ringing times user can make system settings from remote ca
3. 2 Arm Press the Arm button on the remote control The system is in the armed state Keep pressing the test button at the back until the siren sounds Note The testing mode sustains for 3 minutes Then the LED blinks twice indicating the detector is in the power saving mode Installation 1 Choose installation place It is recommended to mount it at the height of 2m from the ground For installation notices please see page 21 22 J J Ground 2 Fix the detector Fix the installation bracket on the wall with screws and then fit the groove at the back of the detector on the bracket 19 3 Testing Press the test button on the back of the detector walk in the detection scope and watch the LED indication to make sure the detector is working Vs FS wis iG ie as e Se eae Pee Ys fins T amp AS i 4 Adjust the bracket angle Adjust the bracket angle to achieve the best detection effect ff Side view D Top view Note If pet immune function is used please do not adjust the angle up or down but keep it parallel with the wall se Detection Scope Om 2m 4m 6m 8m 2m IESSS Om Side view 20 1 Installation Notices Pay attention to the following during installation Mount the detector to a location close to the entry or exit The detector aims at preventing intrusion Detecting human movement at the entry or exit is critical for securit
4. are connected to the control panel Add Delete Remote Controls or Wireless Keypads Add Log on the menu press J or 7 choose Accessories press Enter Press 4 or 1 choose Remote amp Keypad press Enter Press 4 or 1 choose Add press Enter LCD display will show Please connect press any button from the remote control to enable signal transmitting to the control panel When a beep is heard LCD display will show Remote 01 10 connection succeeded When 2 beeps are heard it means this accessory has connected with control panel before Note When adding wireless keypad to control panel please enter access code and then press arm or disarm button on the wireless keypad When a beep is heard the system is connected to the panel successfully So Delete If user wants to delete the added remote controls or wireless keypads please choose Delete in step as above and press Enter Then choose to delete all or specific remote controls or wireless keypads press Enter again Add Delete Edit RFID Tags Add Log on the menu press 4 or choose Accessories press Enter Press 4 or T choose RFID Tag press Enter Press 4 or choose Add press Enter LCD display will show Please connect place the RFID tag close to the RFID reader on the control panel When a beep is heard LCD display wi
5. is cut off PIR 910 Pet Immune PIR Motion Detector x 1 Pet Immune PIR Motion Detector is an intelligent passive infrared motion sensor designed to detect human movements within an approximate range of 0 to 8 meters from the detector The detector includes fuzzy logic to minimize false alarms from unwanted heat sources With power saving feature the detector will enter sleeping mode after the second activation within 3 minutes to save power AC Adapter x 1 Supply power to the control panel In case of power failure two built in backup batteries in the panel will support 5 hour standby Telephone Cable x 1 Connect PSTN land line to the control panel In case of emergency the panel will hoot on site and call the pre stored alarm phone number to notify users Bracket for PIR Motion Detector x 1 Plugs x 4 Tag 26 RFID Tag x 2 The RFID tag is for disarming the system and unlocking the electronic door lock if connected Screws and Wall DWC 102 Wireless Door Window Contact x 1 The Door window contact can be installed on doors windows and any other objects that open and close The sensor transmits signals to the control panel when a magnet mounted near the sensor is moved away 01 RC 80 Wireless Remote Control x 2 The remote control is compact and portable it is convenient to carry it to arm disarm part arm the alarm system and also make an emergency call
6. keep this user manual for your reference when necessary Features 100 wireless configuration D LY installation Stylish design with touch keypad LCD with guide menu easy for programming Built in 1 000 000 RF codes combination maintains high reliability Support 10 remote controls 50 wireless sensors and 50 RFID tags Store 6 alarm phone numbers 10 seconds voice memo and alarm voice message recordable Disarm by RFID tags and unlock the electronic door lock Support maximum 150 alarm event logs Make phone calls directly Duress code enables sending out alarm notification mutely One group of timing arm and disarm Support exit amp entry delay Rename all zones and RFID tags Easy operation with phone remote control function Arming disarming and recording voice memo via App through SMS or GPRS Package List CG B11 Control Panel x1 The control panel is known as the heart and brain for alarm system which is used for receiving and processing signals from wireless sensors and remote controls Users can make settings freely with the keypad and LCD display In case of emergency the panel hoots on site and dials the pre stored alarm phone numbers automatically When users pick up the phone they are able to hear alarm voice message and choose to monitor on site or disarm the system etc As a PSTN GSM dual networks alarm system B11 panel will switch to GSM network automatically to call the user for alert when the PSTN network
7. normal level moisture appears inside damaging PCB 6 Test the alarm system regularly and perform troubleshooting in time 7 Check the built in batteries of accessories regularly If the batteries are low replace with new ones 8 The alarm system requires uninterrupted power supply for working or standby Therefore you need to connect the AC adapter to a reliable power outlet 9 Avoid placing the control panel and sirens in bedrooms or offices so as not to disturb your rest or work 10 It is recommended to cut off the power if the system is not used for long time 11 If the alarm system is covered with dirt wipe off the dirt with soft cloth or tissue For stains apply diluted alkaline detergent to soft cloth wring the cloth out and wipe the product Then dry the product with dry absorbent cloth Please carefully read and strictly follow the previous suggestions If the product remains faulty you can send it to the place of purchase or authorized maintenance center for maintenance We will provide help as soon as possible 52 53 FAQ Cause of Malfunction Troubleshoot Method oes Open battery compartment Power switch is off p y p turn on the power Contact local main power supply bureau Lithium battery backup Connect to main power with power exhausted adapter Panel not in learning Make sure the panel set in status learning status Make sure the triggered accessories transmitting signal No response from control pa
8. number directly without 0 or 9 Voice Memo Press the Record Voice Memo 9 button for 3 seconds to record 10 seconds voice message The Play Voice Memo circle will be flashing to remind you Users can touch the center of circle to listen to the voice memo The LED indicator blacks out when the voice memo has been played Replay by touching it again The latest voice memo will cover the former message Function Setting Input the admin code Default 123456 and then press Enter to enter setting menu T Up Enter Confirm J Down Esc Back to last step 10 Security Alarm Function Test Accessories Our accessories can work only with our control panels can not work with other brands Remote Control RC 80 remote control is dainty and delicate easy to carry It can be attached to your key ring or just put into your pockets or purses When you are about to exit or entry the house you can use it to arm or disarm the system In case of emergency Just press the SOS button the alarm will be activated immediately Appearance LED Status Indicator Disarm Panic 11 Arm Press the Arm button the system enters arm state when one beep is heard and the arm LED on the control panel is on ee Note If Exit Delay is activated all zones except the 24 hour zone will enter arm state after the set delay time Disarm Press the Disarm button on the remote control the system enters disarm sta
9. t Double Sided Tape for Door Window Contact x 2 Brackets Wall Mounted and Desktop for Control Panel x 2 User Manual x 1 02 Control Panel Layout Front Side GSM Network LED Home Mode Part Arm RFID Tag Reader pe Play Voice Memo i Arm LCD Display Clear LED Indicator Call SOS Voice Memo Button 03 Rear Side MIC Tamper Switch Speaker Terminals for Wired Sensors SIM Card Slot AC Adapter Landline Jack Jack ON OFF Backup Batteries Output Wired Siren 500mA NC Input for Wired Sensor Normal Zone Output for Electronic Lock 04 Preparation before Use Insert a SIM Card a This step can be ignored if GSM function is not applied Power on Insert a SIM card into the card slot according to the mark and lock it 1 Plug the output connector of AC adapter into the adapter Jack of control panel 2 Plug the AC adapter into a wall outlet Note In daily use it is a recommended to use i external power supply 7 The built in rechargeable battery should be used only in the case of AC power failure Note A GSM SIM card with normal functions calling answering SMS and caller display is required If use App to control the alarm system through GPRS network it is recommended Connect PSTN Land Line to activate a GPRS plan to save expense B11 is a PSTN amp GSM dual networks alarm system If there is an alarm it will auto dial Ins
10. the disarm LED Indicator lights on Emergency Call When the LCD display is activated Hold the the system goes into emergent E button for 3 seconds alarming state with siren hooting meanwhile the panel will auto dial pre stored alarm phone numbers 08 Access Control System The control panel has a RFID reader for unlocking the electronic door lock by disarming the system Just place the RFID tag close to the RFID reader the blue LED indicator flashes once The system is disarmed and the electronic door lock is opened If connected Make Phone Calls The control panel has a built in communication module If the PSTN land line is connected or SIM card is connected properly and the credit is enough you can use the panel to make calls System will auto dial through land line first or dial through GSM network when land line is Unavailable When the control panel is in disarm or home mode state press Call button input the phone number and press Call button again the line will get through If you input wrong numbers press Esc button and input again Press Esc button to cancel dialing or press Call button to end a conversation Pe Note If control panel is connected with extension line 0 or 9 need to be added in front of the phone number when making phone calls if the land line is unavailable system will switch to GSM network user can make phone calls by inputting phone
11. CHUANGO Susten Sellinas Dual Networks Alarm System 2014 Chuango Security All Rights Reserved ei as User MI d N u al B11 PSTN GSM Table of Contents Package List CO orel GUE aes Preparation before Use Power on Connect PSTN Land Line Insert a SIM Card Lontoo ronel COEN cee rac eama Alarm Control Access Control System Make Phone Calls Voice Memo Function Setting SEO Test Accessories Remote Control Door Window Contact Pet Immune PIR Motion Detector LCD Display Connie tapit s IRN Settings Alarm Phone Number Setup Add Delete Edit Accessories System Settings Check Event Logs Connect to Electronic Lock Connect to CMS Add CMS Phone Number Delete CMS Phone Number User ID Upload Arm Disarm Report to CMS Center 01 02 03 04 05 06 05 05 06 PLD 07 09 09 10 10 Ilez 11 11 14 16 oar 20039 28 29 31 39 E 40 41 40 40 40 41 Remote Control Instruction Answering Alarm Phone Call to Start Remote Control Remote Control by Calling Fixed Phone Number Remote Control by Calling SIM Card Number SMS Operation Disarm Arm Away Arm Home Mode Part Arm Monitor Recording Voice Memo App Operation Download and Install APP Control through SMS Control through GPRS Data Maneno eee ira ERE RTE FAQ CGI LAY ally 41 42 42 43 44 43 43 44 44 44 45 51 45 46 48 52 53 54 55 56 Please read this user manual carefully Please kindly
12. Setup Arm Disarm Tone lt On Off gt User can set 6 user phone numbers and 2 CMS phone numbers When connecting to Siren On Off lt Off Low High gt CMS system will dial CMS phone number to upload Contact ID reports while alarming Built in Siren and then dial 6 user phone numbers in sequence one by one System will dial all the ee user phone numbers in 3 cydles until the phone is answered together with any operation on phone buttons System Settings Siren Alert Time lt 300S gt User ID lt 1234 gt Input 4 Digits Off Disarm Upload on Off CE Add Alarm Phone Number Log on the menu choose Phone Numbers press Enter 2 Press or T choose Add Phone Number press Enter Press J or 7 choose Alarm Number1 6 press Enter Input alarm phone numbers in order press Enter If group extended telephone number is used 0 or 9 need to be added in front of the phone number Note If user wants to check or edit the stored phone number enter Alarm Number1 6 to check and edit ee toy f Delete Alarm Phone Number Log on the menu choose Phone Numbers press Enter 2 Press V or fF choose Delete Phone Number press Enter Press 4 or 4 choose Alarm Number1 6 press Enter Delete the alarm phone numbers in order press Enter again ese eee se 27 28 2 Add Delete Edit Accessories The control panel only receives signal from accessories after they
13. again to start testing mode for 10 minutes Please trigger coded sensors in order the sensors will transmit signals to control panel When 3 beeps are heard LCD display will collect the triggering time of the sensors Then you can count the connected sensors based on the numbers displayed on the LCD screen Exit by pressing Esc button 3 System Settings Date and Time Date Log on the menu press 4 or 1 choose System Settings press Enter Press 4 or 7 choose Date and Time press Enter Press J or 4 choose Date press Enter Input date press Enter 3l YO oe Date Format Log on the menu press 4 or choose System Settings press Enter Press 4 or 1 choose Date and Time press Enter Press 4 or 1 choose Date Format press Enter Press 4 or T choose format press Enter Time The default time is set on 24 hours standard Log on the menu press 4 or 1 choose System Settings press Enter Press 4 or 4 choose Date and Time press Enter Press 4 or 7 choose Time press Enter Input current time press Enter Entry and Exit Delay If user is not used to taking along with the remote control entry and exit delay could be set When entry and exit delay is set user could exit the house in set time period then system will be armed automatically when user is back
14. ain menu user can perform disarm arm home arm monitor and leave voice memo 3 Delete accounts Press Tif on the main menu after login tap OK on the dialog box to confirm deletion 50 4 Refresh Press to refresh the current system state 5 Add family accounts Press I to enter the account management interface and input family member s mobile number as their login name tag OK The default password of family account is 123456 user can change it when login The main account can add at most 5 family accounts Family accounts can be deleted by tapping the on the right side in the accounts list 51 Maintenance The alarm system features unique and brilliant design and craftwork Please use it with caution The following suggestions will help prolong the service life of the system 1 Keep this product and accessories out of children s reach 2 Keep the product and accessories dry Rainwater moisture and liquids are likely to contain minerals that will corrode electronic circuits 3 Do not use or store the alarm system in dusty or dirty places otherwise it may damage the electronic components 4 Do not expose the alarm system to high temperature High temperatures can shorten the life of electronic components damage batteries and cause melting and deformation of plastic parts 5 Do not store the alarm system in cold areas Otherwise when the temperature of the alarm system rises to the
15. arm activation Appearance LED Status Indicator Transmitter Magnet LED Indication LED Meaning Blinks once Door Window contact is triggered Low battery indication LCD shows Sensor 1 50 Sensor Name Low Battery Please change the batteries immediately Blinks once per 3 seconds PCB Layout gt gt i ul lt J o gt Tamper switch 14 NO FR 15 Test Press the back cover and slide down to remove the back cover Remove the insulating strip The contact works immediately Press the Arm button on the remote control The system switches to the arm status Separate the transmitter and magnet The LED is on and the panel alarms It indicates that the sensor works properly et ese ee ee ee ee Note There are triangle marks on the side of the transmitter and magnet Make sure the triangle marks face each other and within the range of 1 cm ee ee Installation Mount the transmitter on the frame and the magnet on the door or window Make sure the magnet is on the right side of the transmitter Secure the transmitter and magnet on the desired locations with double sided tapes or screws ee Note Make sure the transmitter and magnet works properly on the desired locations If a metal door is installed place spacers under the transmitter and magnet Do not apply the contact to a rolling shutter Purchase dedicated contacts for rolling shutters when necessa
16. e the reminding rhythm will speed up in the last 15 seconds sm Backlight Time User can set standby time of the backlight on the blue LCD display accordingly Log on the menu press J or T1 choose System Settings press Enter Press 4 or 4 choose Backlight Time press Enter Input time for backlight time press Enter Backlight time is calculated on seconds default is 20 seconds setup range is 01 99 seconds Timed Arm Disarm User can set timed arm and disarm according to daily schedule to avoid repeated operation Timed Arm Log on the menu press 4 or choose System Settings press Enter Press J or T choose Auto Arm Disarm press Enter Press J or choose Auto Arm Time press Enter Input exact time for arming press Enter 33 Timed Disarm 2 Log on the menu press J or 1 choose System Settings press Enter for confirmation Press 4 or 1 choose Auto Arm Disarm press Enter Press J or 1 choose Auto Disarm Time press Enter Input exact time for disarming press Enter Edit Greeting Message When greeting message is set turn on the alarm system or activate the touch keyboard the greeting message will be shown on LCD display Log on the menu press J or 1 choose System Settings press Enter Press 4 or 1 choose Edit Welcome press Enter to d
17. e Number press Enter Press J or 1 choose in order CMS Number1 2 press Enter Delete stored CMS phone no Press Enter User ID It is supplied by CMS center After it is stored CMS center can exactly know user s location according to the ID number Log on the menu press J or T choose System Settings press Enter Press 4 or T choose User ID press Enter LCD display will show Input 4 Digits input 4 digits user ID press Enter 40 Upload Arm Disarm Report to CMS Center When this function is enabled all arm disarm reports will be uploaded automatically to CMS center so that CMS center can know the status of the alarm system After the User ID is set press 4 or to choose Arm Upload or Disarm Upload press Enter Press JL or 7 Choose On press Enter When choosing Off during setup press Enter arm disarm report will not be uploaded to CMS center Contact ID Reports Remote Control Instruction Users can operate the system by the control panel or remote control Besides using phone call SMS or App on the phone can also operate the system remotely Phone remote control can be achieved through two ways Answering Alarm Phone Call to Start Remote Control When an alarm occurs the control panel will call the stored phone numbers When answering the call the user will hear the recorded voice m
18. ecifications CG B11 Control Panel Power Supply Standby Current Alarm Current Backup Battery Internal Siren Volume Radio Frequency Maximum Stored Phone No Maximum Remote Controls Maximum Sensors Maximum RFID Tags Maximum Event Logs Housing Material Operating Condition Dimensions L x W x H RC 80 Wireless Remote Control Power Supply Alarm Current Transmitting Distance Radio Frequency Housing Material Operating Condition Dimensions L x W x H Input DC 12V 500mA 6Wh lt 90mA lt 300mA BL 5B 3 7V 800mAh rechargeable lithium battery x 2 pcs 95dB 315MHz or 433 92MHz 75KHz 6 alarm phone numbers and 2 CMS numbers 10 pcs 50 pcs 50 pcs 150 events ABS plastic Temperature 10 C 55 C Relative Humidity lt 80 non condensing 185 x 130 x 27mm DC 3V CR2025 Lithium Battery x 1pc lt MA lt 80m in open area 315MHz or 433 92MHz 75KHZz ABS plastic Temperature 10 C 55 C Relative Humidity lt 80 non condensing 58 x 31 x 9 5mm 54 DWC 102 Wireless Door Window Contact Power Supply Static Current Alarm Current Transmitting Distance Radio Frequency Housing Material Operating temperature Transmitter Dimensions L x W x H Magnet Dimensions L x W x H DC 1 5V AA 1 5V LR6 Battery x 1 pc lt 35UA lt 10mA lt 80m in open area 315MHz or 433 92MHz 75KHz ABS plastic Temperature 10 C 55 C Relative humidity lt 80 non conden
19. ector enters power saving mode Hold the test button and load the battery then release the test button the detector stands in testing mode it keeps detecting once every 10 seconds Exits this status by reloading the battery without holding the test button Power saving mode The product features power saving design If the detector detects human movement twice in 3 minutes it will switch to the sleeping state to save power At this time the LED will not blink and no alarm After no movement within the next 3 minutes the detector switches back to the working state automatically 7000000000000000000000000000000000000000000000 0 0 7 Note After the detector is in the sleeping state ensure no human movement within 3 minutes otherwise the detector remains sleeping In the sleeping state it is recommended that you leave the room after arming the system Ensure no human movement in 3 minutes Then go into the room the system alarms immediately 17 Case Al Case 2 Press Initial start the test button and then arm and then arm 3 minutes later Sleep after detecting human movement twice No human movement within 3 minutes Switch from sleep to arm Test 1 Remove the insulating strip Press the buckle to open the back cover Remove the insulating strip After 30 second selftesting the detector switches to the testing mode to 3 Trigger the alarm
20. efine the greeting message gt means to delete means to space J means to move backward 7 means to move forward Line Cut Alarm When linecut alarm function is on the control panel will alarm once the PSTN land line is cut or pulled out even if the built in siren was set to mute Turn On Off Linecut Alarm Log on the menu press J or 1 choose System Settings press Enter Press J or 7 choose Linecut Alarm press Enter Press J or T choose On or Off press Enter On is to turn on the linecut alarm Off is to turn off the linecut alarm Default setting is On the linecut alarm is on Keypad Tone User can turn on off keypad tone accordingly Turn On Off Keypad Tone Log on the menu press 4 or 1 choose System Settings press Enter Press 4 or 1 choose Keypad Tone press Enter Press 4 or T1 choose on or Off press Enter On is to turn on the keypad tone Off is to turn off the keypad tone Default setting is On keypad tone is on 34 Access Code All the alarm panels are with default user code admin code and duress code Please change all codes before using and keep your codes secret Admin Code With admin code user can arm and disarm make system settings as well as reset codes etc Log on the menu press J or 1 choose System Settings press Enter
21. ert the SIM card only after the control panel is switched off Then switch on the control pre stored phone numbers though landline or dial through GSM network when pallets asst sea ges If no SIM card is inserted the control panel can only send alarm notification by calls through landline is unavailable land line and users cannot remote control the control panel through App However other A functions are not affected 1 Connect the smaller connector of provided telephone cable tothe OJo a PSTN land line interface at the back side of the panel 2 Connect the other end of the telephone cable to the signal output provided by PSTN land line operator 05 06 O07 Control Panel Operation Alarm Control Arm Away Arm Press the Arm button on the control panel the system enters Arm state when one beep is heard and the arm LED Indicator lights on zones except the 24 hour zone will enter arm state after the set delay time Home Mode Part Arm Press the Home Mode button on the control panel the system enters home mode when one beep is heard and the home mode LED Indicator lights on All the normal sensors are armed except the home mode sensors which are disarmed so that users can move freely at home Disarm Input user code Default 1234 or admin code Default 123456 first then press the Disarm button the system enters disarm state when one beep is heard and
22. essage firstly Then you can press the telephone keys to operate the system remotely See instruction table on the next page The control panel will call these numbers for three rounds at most when user pick up with key operation control panel stops dialing if not control panel keeps dialing until three rounds are finished 41 Remote Control by Calling Telephone Number Call the telephone number of alarm system After getting through input user code or admin code and press to confirm Users can choose the related instruction to make remote control operation See instruction table below If there is no operation within 30 seconds the system will hang up Remote Phone Control Instruction Table Available when relay is used Press 5 Turn off relay Press 44 To exit Remote Phone Control Or hang up the phone Remote Control by Calling SIM Card Number The system will enter monitor state directly when stored phone number called the SIM card number of control panel User is able to continue the operation by input relative command While any phone number can proceed this function without phone number is stored So it is command to store the phone number at the first beginning of the setting 42 SMS Operation You can control the system by sending SMS commands to the SIM card No SMS is charged according to telecom operator Any phone number can send SMS to control the system by default after you store alarm p
23. hone numbers to the control panel system accepts only the commands from these numbers Disarm This is to disarm the system In disarmed status the detectors except those accessories in the 24 hour zone will not trigger an alarm when detecting intrusion System disarmed Arm Away Arm This is to arm the system In armed status the system will trigger an alarm when detecting intrusion System armed 43 Home Mode Part Arm In home mode detectors setting to home mode zone are in disarmed status the other detectors are still in armed status That is you can move freely in the home mode zone however the rest areas are still being protected System in home mode Monitor This is to monitor the site remotely by call back from the control panel After the control panel receives the SMS it calls your phone number Then you can answer the call and monitor listen in the site Recording Voice Memo This is to record a 10 second voice memo by call back from the control panel After the control panel receives the SMS it calls your phone number Answer the phone and then you can start to record a 10 second voice memo The control panel will hang up phone after 10 seconds 44 45 App Operation This system can be controlled through SMS or GPRS interface on APP If user choose SMS for iPhone the interface of sending SMS will display For Android smart phones SMS will be directly sent to the
24. k press Enter Relevant event log time and alarm way will be shown ee nn Note Hold J or to skip the event logs 000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 07 Connect to Electronic Lock Please ignore this if user is Not intended to put this alarm as access control This alarm only sends on off signal to electronic door lock please refer to related electronic door lock manual for details 39 Connect to CMS Please ignore this step if users don t need to connect to CMS center When connected to CMS center control panel will upload contact ID to CMS center automatically once intrusion is detected Add CMS Phone Number When CMS center phone no is stored the control panel will auto dial to CMS center automatically when alarm Log on the menu choose Phone Numbers press Enter Press 4 or 7 choose Add Phone Number press Enter Press 4 or 4 choose CMS Numberl or CMS Number2 press Enter Input CMS phone no press Enter If group extension telephone no is used to connect to the CMS center please add 0 or 9 before the phone no you plan to store os Note If user wants to check or edit the pre stored phone no enter CMS Numberl 2 to check or edit a Delete CMS Phone Number Log on the menu choose Phone Numbers press Enter Press 4 or 7 choose Del Phon
25. larm 24 LCD Display Menu When LCD is activated input the admin code Default 123456 and then press Enter to enter setting menu Sub Menu 1 Sub Menu 2 Sub Menu 3 Phone Numbers Accessories Alarm Numper1 6 Add Phone Number CMS Number1 2 Alarm Numberl1 6 Del Phone Number CMS Number1 2 wo S ALL Remote amp Keypad Delete Remote 01 10 RFID Tag Delete RFID 01 50 Delete a 01 50 Sensor 01 50 Wirel ireless Edit Sensor Type Sensors Normal Sensor 24 Hour Sensor Delay Sensor Home Sensor Edit Sensor Name mode oe Time w o ppo Entry Delay lt 000S gt Entry Exit Delay Exit Delay lt 000S gt Backlight Time lt 20S gt Auto Arm Time lt 00 00 00 gt Auto Arm Linecut Alarm Keypad Tones Input 6 Digits RON OOK lt Default Code 123456 gt Access Input 4 Digits Code lt Default Code 1234 gt Input 4 Digits lt Default Code 1111 gt Disarm Auto Disarm Time System lt 00 00 00 gt Settings 26 Settings Alarm Message Rea When LCD is activated input the admin code Default 123456 and then press Enter to enter setting menu Siren On Off lt On Off gt Wired Siren Important The default language of this alarm system is English you can change in the l Arm Disarm Tone lt On Off gt Language menu of System Setting Siren On Off lt On Off gt Siren Setup Wireless Si seca eal 1 Alarm Phone Number
26. ll show RFID 01 50 connection succeeded When 2 beeps are heard it means this accessory has connected with control panel before 29 Delete If user wants to delete the added RFID cards or tags please choose Delete in step as above and press Enter Then choose to delete all or specific RFID cards or tags press Enter again Edit If user wants to rename the added RFID cards or tags please choose Edit Name in step as above and press Enter then input the name ett eee eee So 0 nn A Add Delete Edit Wireless Sensors Add Log on the menu press J or T choose Accessories press Enter Press J or choose Wireless Sensors press Enter Press 4 or 1 choose Add press Enter LCD display will show Please connect trigger the detector once to make it send wireless signal to the control panel When a beep is heard LCD display will show Sensor 01 50 connection succeeded When 2 beeps are heard it means this accessory has connected with control panel before Delete If user wants to delete the added sensors please choose Delete in step as above and press Enter Then choose to delete all or specific wireless sensors press Enter again Edit Edit Type of Sensors Log on the menu press 4 or choose Accessories press Enter Press or choose Wireless Sensors press Enter Press 4
27. lling such as arming disarming the system Log on the menu press 4 or 1 choose System Settings press Enter Press J or 1 choose Ringing Times press Enter Input 5 9 for ringing times press Enter Default setting is 5 times Alarm Message User can leave a 10 second voice message when control panel makes call to user s stored phone number voice recording will be repeatedly played to notify the intrusion Record Alarm Message Log on the menu press J or T choose System Settings press Enter Press J or T1 choose Alarm Message press Enter Press J or T choose Record press Enter LCD display will show Record 10s Voice to remind you of the 10 seconds voice recording press Enter Start voice recording for 10s until the system stops automatically or press Enter to stop recording Siren Setup Users can turn on off wired siren wireless siren built in siren as arm disarm beep and Set siren ringing time Wired Siren Wired siren is connected to the control panel by wire Turn On Off Wired Siren Log on the menu press 4 or T choose System Settings press Enter Press 4 or 4 choose Siren Setup press Enter Press L or M choose Wired Siren press Enter Press 4 or 1 choose Siren On Off press Enter Press J or 1 choose On or Off press Enter
28. ncluding without limitation lost profits or loss or damage to data arising out of the use or inability to use this document even if the product has been advised of the possibility of such damages 56 CHUANGO STAA iE 64P
29. nel operation Accessories cannot connect to control panel No response from the control panel by operating remote control Touch keyboard fail to make related setting No response after inserting a SIM card APP replied Return data run out APP replied Control panel offline The direction of the SIM card is not correct Accessories not triggered for learnin 3 to panel for learning The control panel has different radio frequency with accessories Please contact retailer for help Remote control is not Follow the manual and connect learned to control panel the remote control to panel Remote control the panel in Out of range between remote control and panel proper distance Signal repeater could be added RFID card tag fail RFID card tag not connected Follow the manual and connect to disarm to the panel RFID card tag to the panel Input the correct admin code press Enter and log on menu Not logged onto the setting menu setting Switch on the control panel first and then insert the SIM card The SIM card is not a GSM Please use GSM SIM card SIM card Please check the network of control panel and mobile phone works properly Please check the network of control panel Please insert the SIM card again according to the user manual Insert the SIM card first and then switch on the control panel Make sure the network Make sure the SIM card of control panel is not indebted Sp
30. number of the control panel without interface redirection Download and Install APP Search keywords B11 alarm in Apple Store or Google Play downloads it for free Control through SMS Any phone number can operate the system through APP by default after you stored alarm phone numbers on the control panel system accepts only the commands from these numbers 1 Add accounts Adding accounts enables you to bind the alarm systems to your smart phone You can add more accounts to control several B11 alarm systems on one phone 1 Enter Accounts Tap B11 APP choose SMS and then enters account management interface 2 Add account Tap input the SIM card number of the control panel on Mobile Number and then tap OK 46 2 Operations on main menu Tap the SIM card number of the control panel to enter the main menu user can perform disarm arm home arm monitor and leave voice memo 3 Delete accounts iPhone Tap EDIT choose the account number tag to confirm deletion Android phone Tap EDIT press and hold the account number until the dialog box appears tap OK to confirm deletion 4 Control through GPRS Data APN Setting Some SIM cards need to set APN to open GPRS function If the GPRS function of the SIM card in B11 doesn t work out Do as follow Send APN to the SIM card in the control panel you ll get a message back Forward and fill in rela
31. or choose Edit press Enter Press 4 or choose Sensor 01 50 press Enter Press J or choose Edit Sensor Type press Enter Press J or Choose one type of Normal Sensor 24 Hour Sensor Delay Sensor Home Sensor press Enter 30 Normal Sensor In arm mode when normal sensors are triggered system will alarm In disarm mode when normal sensors are triggered system will not alarm 24 Hour Sensor Under any circumstances when 24 hour sensors are triggered system will alarm at once Delay Sensor In arm mode when delay sensors are triggered system will alarm after the set time if the entry delay time was set before For Entry Delay please refer to page 32 Home Sensor In home mode only normal sensors will be triggered for alarming while home sensors will not be triggered This will allow user to move freely at home Names of Sensors If user wants to rename the sensors please choose Edit Sensor Name in step 5 and press Enter Then input the sensor name Note press the button of the control panel to clean when input wrong Press the ESC to exit ee Test Mode Test if the sensors are connected successfully to the control panel Log on the menu press 4 or 1 choose Accessories press Enter Press J or T choose Test Mode press Enter LCD display will show Yes press Enter
32. r built in siren Default setting is On arm disarm beep is on Set Ringing Time for All Sirens Log on the menu press 4 or 1 choose System Settings press Enter Press 4 or 1 choose Siren Setup press Enter Press 4 or 1 choose Siren Alert Time press Enter Input the ringing time press Enter Siren ringing time is calculated as seconds default setting is 300 seconds If 0 second is set siren will not ring 38 User ID for CMS Please see details at Page 40 Connect to CMS Upload Arm Report Please see details at Page 41 Connect to CMS Upload Disarm Report Please see details at Page 41 Connect to CMS Reset Log on the menu press 4 or choose System Settings press Enter Press 4 or 7 choose Reset press Enter to reset the system to default setting ett Note All system settings will be restored to default setting Reset will not delete the accessories 7 that has already coded to the control panel 00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000020mmmm If user forget the admin code and cannot setup the system please contact local distributors 4 Check Event Logs Users can check the event logs freely 150 event logs are traceable Log on the menu press 4 or 1 choose History press Enter Press 4 or 7 choose the event log you need to trac
33. ry mn Infrared sensor Pet Immune PIR Motion Detector The detector adopts digital dual core fuzzy logic control processing technology and intelligent analysis algorithm effective resolution of interfering signal and human movement signal preventing false alarm It features automatic temperature compensation and resistance to flow technology adapting to environmental and temperature change It can detect human movement within the 8 meter cone space suitable for halls hallways etc The detector features pet immunity for small animals up to 25kgs Appearance 1 Detecting lens 2 LED 3 Snap joint 4 Test button 5 Installation bracket LED Indication Blinks continuously Under self testing state Blinks once Intruder is detected Blinks twice 3 minutes testing is finished enters power saving mode Blinks once per 3 seconds Low battery indication LCD shows Sensor 1 50 Sensor Name low battery please change the batteries immediately PCB Layout LED ON OFF Infrared sensor Tamper switch Note If the detector is disassembled system will sound immediately and LCD shows Sensor 1 50 Sensor Name Sensor Tamper el ssellea eeeatioieay bane ee gt gt gt gt i ul JW lt lt m Pasi Pasi a a E E Working Mode Testing mode After self testing the detector enters testing mode and detects once every 10 seconds After 3 minutes the LED blinks twice and the det
34. se Siren Setup press Enter Press 4 or 1 choose Wireless Siren press Enter Press J or 7 choose Arm Disarm Beep press Enter Press 4 or 1 choose On or Off press Enter On is to turn on arm disarm beep for wireless siren Off is to turn off arm disarm beep for wireless siren Default setting is On arm disarm beep is on a7 Built in Siren Built in siren is the siren inside the control panel Turn On Off Built in Siren D Log on the menu press 4 or 7 choose System Settings press Enter Press J or T choose Siren Setup press Enter Press 4 or Press J or choose Siren Siren On Off press Enter Press J or 1 choose Off Low High press Enter Choose Low or High to adjust the volume Off is to turn off the built in siren T choose Built in Siren press Enter The default setting is Low Turn On Off Arm Disarm Beep for Built in Siren Log on the menu press 4 or 1 choose System Settings press Enter Press 4 or 7 choose Siren Setup press Enter Press J or 1 choose Built in Siren press Enter Press J or 1 choose Arm Disarm Beep press Enter Press J or choose On or Off press Enter On is to turn on arm disarm beep for built in siren Off is to turn off arm disarm beep fo
35. sing 71x 34 x1 7 5mm 51 x 12 x 13 5mm PIR 910 Pet Immune PIR Motion Detector Power Supply Static Current Alarm Current Detection Scope Pet Immunity Transmitting Distance Radio Frequency Housing Material Operating Condition Detector Dimensions L x W x H Bracket Dimensions L x W x H TAG 26 RFID TAG Internal Circuit Working Frequency Housing Material Dimension DC 3V AA 1 5V LR6 Battery x 2 pcs lt 90UA lt 9 5mA 8m 110 lt 25kgs lt 80m in open area 315MHz or 433 92MHz 75KHz ABS plastic Temperature 10 C 55 C Relative humidity lt 80 non condensing 108 x 52 x 36 8 mm 52 x 30 x 26 5 mm EM4100 CMOS 125KHz Compound Plastic 30 x 30 x 6mm Disclaimer Dear users We have reviewed this manual thoroughly in order that it will be an easy to use guide to this product All statements technical information recommendations in this manual are believed reliable but the accuracy and completeness thereof are not guaranteed or warranted The specifications and information regarding the products in this document are subject to change without notice Photocopy copy reproduction translation to any language modification storage in a retrieval system or retransmission in any form or by any means electronic mechanical or otherwise is strictly prohibited without prior written permission In no event we are liable for any indirect special incidental or consequential damages i
36. te when two beeps are heard and the disarm LED on the control panel is on When alarm is activated the siren will hoot Press the Disarm button the system is disarmed But the LED indicator of triggered zone keeps flashing for further checking Press Disarm button again the alarming zone indicator goes out Home Arm Part Arm Press Stay button on the remote control the system enters home mode when one beep is heard and the home mode LED is on All the normal sensors are armed except the home mode sensors which are disarmed so that users can move freely at home amp WZ 13 Mute Operation When arm or disarm the system the siren will beep accordingly If siren beep is not needed please operate as x follows Press Stay button on the remote control for 1 second then press Arm or Disarm button The siren is armed or disarmed in mute without disturbing other people So 0 SOS Whenever you press the SOS button on the remote control the system will alarm o immediately Door Window Contact The door window contact can be installed on doors windows and any other objects that can open and close The sensor transmits signals to the control panel when a magnet mounted near the sensor is moved away External input for wired accessory is available at the N C interface The tamper protection ensures that sabotage attempts to move the contact will result in an al
37. ted APN username and password then send it back You ll get a message OK from the SIM card in the control panel to notify you that the setting is successful Turn off the panel and restart then you can operate the APP via GPRS freely For instance for SIM card from Vodafone in Netherlands there is no username and password leave it as it is A message replied OK means the setup is successful APN User name Password APN live vodafone com User name Password OK 2000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Note The APN setting varies in different countries Consult the local operator on how to set the i APN correctly See ee eee ee 2222222222222222 222222222m2n222222222222n222m222222222222n2mn2nmmmm2mn2 48 Register Registering account enables you to bind the alarm systems to your smart phone 1 Enter login interface Tap B11 APP choose GPRS and then the login interface appears 2 Register an account Tap Register inout your mobile number password device ID random code SN code on the back side of the panel and then tap OK Note When register please input user s mobile number instead of the SIM card number of the control panel The device ID random code are shown on the back side of the control panel please keep it properly for safety 49 2 Operations on main menu Login to enter the m
38. without disarming the system entry delay will allow time for user to disarm the system Otherwise the system will take this as an intrusion and send out alarming alert Entry Delay Entry delay is set to leave time for user to disarm the system when delay sensors are triggered Log on the menu press or choose System Settings press Enter Press 4 or 1 choose Entry Exit Delay press Enter Press 4 or 1 choose Entry Delay press Enter Input time for entry delay press Enter for confirmation Entry delay time is calculated on seconds default is 0 second off setup range is 0 999 seconds ee 2 2 2222 22n2n2nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnmnnnnmnnnnmnnmmnnnmnnnnmnmnmnmnmnnnmnnnnmnmmnnmnnmmnnnnmnnmmnn ee 32 Exit Delay Exit delay is set to leave time for user to exit before the system is armed Log on the menu press 4 or 1 choose System Settings press Enter Press 4 or choose Entry Exit Delay press Enter Press 4 or 7 choose Exit Delay press Enter Input time for exit delay press Enter for confirmation Exit delay time is calculated on seconds default is 0 second off setup range is 0 999 seconds Note Once delay time is set when arm the system one beep will be heard every second to remind the user to leav
39. y 2 21 Mount the detector in a proper angle The installation angle affects sensitivity directly The sensitivity is optimal when the walk direction is vertical to the infrared direction Choose the best N Ss location and angle according to the actual situation and detection scope diagram SS S 3 Avoid facing to glass windows or doors Strong light interferes with detection sensitivity In addition complicated situations such as traffic flow stream of people also should be avoided 4 Avoid facing or positioning close to heat Avoid facing or positioning close to heat sources such as heat extraction units heaters air conditioner microwave oven refrigerator which may cause false triggering 5 Avoid facing to swinging objects Swinging objects may also trigger false triggering Besides if there are two detectors covering the save scope adjust the locations to prevent cross interference ZZ 23 LCD Display Contents System Status Display content Stand by Disarm Arm or Disarm SMS Home Arm 505 Alarm Linecut Alarm Sensor 1 50 Sensor Name Panel Tamper Low Battery NO SIM CARD GPRS Connecting Wired Sensor Sensor 1 50 Sensor Name GPRS Disconnected Sensor Tamper System Arm Alarm Sensor 1 50 Sensor Name System Disarm System Home Arm Remote Arm Remote Disarm Arm or Disarm Remote Home Arm RFID 1 50 RFID Name Disarm ae Disarm GPRS eo Arm A
Download Pdf Manuals
Related Search