FC 80 FC 90 - Yachting Electronic Co., Ltd
Contents
1. www goyachting cn right reserved Except as expressly provided herein no part of this manual may be copied reproduced repub lished transmitted or distributed for any purpose without prior written consent of Yachting Electronic Co Ltd Yachting Electronic may find it necessary to change or end our policies regulations and special offers at any time We reserve the right to change or improve its products and to make changes in the content without obligation to notify any person or organization For current updates or other information please visit our website www goyachting cn Yachting Electronic Co Ltd Building107 No 508 Heyan Road Nanjing 210038 China Printed in China Copyright 2008 Yachting Electronic Co Ltd All rights reserved i ENA 1 PAC e NEM 2 Using Ehe DEOQUOL 4 Installingihe battery nn 5 Install the RemoteEye to bait 6 Introduction of Remotelyeu iiie aan J SPO A 8 RemoteEye installation method 1 8 RemoteEye installation method 2 18 Operational Panel opi 24 Di Day Ud Men IM UND 25 Understanding the dsl senses 25 DCT TANCE 26 Water surface DID een 22. There are so much debris in the water 46 7 The sonar unit can not reach 300m There is a abnormal display on the display and when the bait boat is about 60 70m far away the sonar unit stop working a Please confirm the sensor is mounted at the proper location on your bait boat A improper mounting location will cause abnormal display b Please check whether you are using the bait boat batt ery for power suppling For FC80 we strongly suggest you connecting the RemoteEye to a separate 9v Alkaline battery not connecting it to your bait boat battery Otherwise abnormal display may occur For FC90 both is accepted c Please check the RemoteEye installation and confirm the antenna mounted on your bait boat is correctly connected to the control box through the antenna extended cable d The radio performance is easily effected by cloudy or rainy day which will cause the Remote Control distance decreasing greatly 47 Maintenance With a view to making use of your Fishfinder we reco mmend you follow the steps below and carry out maint enance 1 For the case Cleaning the sonar unit s outer case except for the screen with a cloth dipped mild detergent solution and then wipes it dry 2 For the screen Use a piece of soft cloth or pelt to clean the screen fresh water or eyeglass cleaner can be used if needed Stubborn dirt or oil stains remaining on the screen shall not be wiped with force otherwise it
3. 3 Technical and casing Monitor and display voltage of bait boat battery FC90 only Built in memory stores sonar settings Temperature Air temp water temp FC90 only included 50 Operational Temperature From 10C to 50C 14 Fto122 F Units f ft f m C ft C m Unit Dimensions 138mm x 69mm x 32mm Casing IPX7 Waterproof 4 Power Handheld Power Supply 4xAAA Alkaline batteries Handheld Battery Life 45 Hours Continuous Use Handheld Power Off Automatically In 10minutes Without Any Using RemoteEye Power Supply 6 12v battery 2 Features 1 Switchable Fish Identification Mode 2 Sensitivity 0 100 Range Adjustable 3 Select Depth Range Automatically 4 Freeze Screen At Any Time 5 Big Small Fish Identification 6 Fresh amp Salt Water Environment Using 7 True Changing Water Bottom Graph 8 Multi Languages Menu Operation 5l Contact Us Contact Our Resource Center in any of the following days By telephone Monday Friday 8 am to 5 30 pm Central Standard Time 0086 25 84680809 Or by e mail Typically we respond to you in 2 business days info goyachting cn For direct shipping our address is No 508 Heyan Road Nanjing 210038 China Yachting Electronic Co Ltd Scale 1 1 Unit mm 53 www goyachting
4. User s Guide carefully For any possible problems you may encounter during the operation please switch to the Trouble shooting section for reference Packing list Before you install the transducer to your bait boat please check the packing list below and make sure you are not missing any items D 9 OL qw _ 1 A wireless remote sonar sensor 2 A control box 3 A antenna for mounting on bait boat 4 A power cable 5 A anenna extended cable 2 6 A antenna for mounting on the sonar handheld optional for FC80 not inlcuded in FC90 7 sonar handheld with 3 FSTN LCD 8 A switch for On Off controling of RemoteEye optional The following items are also included two screws mounting the transducer b a battery buckle when needed being used to connect power cable and 9v alkaline battery a copy of manual Note the electric control amp sonar system enclosed by the dashed line are named RemoteEye In the event that any of the items listed is found missing call us immediately or log on to our website at www goyachting cn Clients located in other parts of the world may also refer to their respective local distributors Using the product FC80 90 is designed to be used with bait boat Properly install the RemoteEye to your bait boat power on the control box before you put the assemmed bait boat amp RemoteEye into
5. b screw the antenna to the antenna extended cable EN 11 4 Mount the wireless sensor on the supporting plate as instructed below a drill three holes on the supporting plate Diameter of hole 1 is about 12 5mm Diameter of hole 2 and hole 3 is about 3 5mm Note use a pencil to mark the position before drilling the hole 2 and hole 3 screw 12 5 Mount supporting plate on the top cover of bait boat Drill 4 holes on the supporting plate and tighten the supp orting plate on the top cover of your bait boat by screws 6 Find a proper position and place the control box into the bottom cover of your bait boat 19 find a proper position Note It could be better to find a way to fix the control box in the bottom cover of your bait boat As when used with your bait boat in the water the control box may wobble with the shave which may damage the inner electronic parts 7 Connect the antenna extended cable to the control box 14 9 connect the control box to the battery 0 connect to the battery a for FC80 4 Warning we strongly suggest you using a 9v alkaline battery instead of using the bait boat battery for powering otherwise thus short Remote Control distance and abnormal display may occur due to the interference caused by bait boat battery b for FC90 Both bait boat battery and 9v alkaline batte
6. 1 MISCUIT 29 Menu Operation Instruction eere einen 29 SEHR TUN 31 Bru 22 33 Depth RADE ae 34 FEN euere 35 Ua A 36 lo esed re En MN quate 37 OMAS en 38 Load DF 39 Monitor SEL FC90 Fishfinder only 40 BAT Alarm FC90 Fishfinder only 41 nee 42 Trouble SMO 43 hut o FM 48 Guarantee COMTI 49 Specifications and Features 50 SPECIOAL ee 50 Features 51 Introduction Thank you for choosing our Fishfinders and welcome to the innovations of Yachting Electronic Co Ltd We has been committed to fish finder R amp D activities all the way and its products have been reputed for their cutting edge technologies and reliable performance 80 90 is designed to be used with bait boat We offer 12months charge free maintenance against any damages induced by non human factors and damages beyond the 12 months are handled with reasonable charges based on concrete situations For details regarding maint enance service please refer to the warranty explanations To familiarize yourself better with the product s operation and maximize the utilization we invite you to read the
7. Temperature Reading EN POWELK CY Voltage Reading 11 Ent Key FC90 only 12 Menu and Exit Key 5 Fish Icon 13 Down Arrow Key 6 Bottom 14 Up Arrow Key 24 Display 1 Understanding the display Depth reading Temperature reading Voltage reading of bait boat battery FC90 only Fish icon Sensitivity Water surface line Sonar information scroll from right to left L Bottom 1 90 0 20 Depth range Handheld battery strength 1 Depth reading indicate water depth 2 Temperature reading indicate air or water temperature Voltage reading indicate the voltage of bait boat battery 3 Sensitivity the curren sensitivity setting 4 Water surface line display the position of water surface 5 Fish icon a fish symbol to display the detected target 6 Bottom indicate the bottom condition 25 7 Depth range the current Depth range setting 8 Battery strength indicate the remained handheld battery strength The detection graph is shown from the right corner from top to down It would scroll forwards to left continuously The most present and newest signals are displayed on the rightmost screen 2 Depth range The unit will automatically adjust the depth range according to water conditions It always keeps the bottom displayed in the lower portion of the screen When the depth unit is set to feet this fish finder has the fol
8. appears run your bait boat back as soon as possible You also could exit alarm mode by enter into BAT Alarm menu and artificially increase the setting to a safe value To set the BAT Alarm 1 Press MENU to enter into menu setting 2 Use the Up Down Arrow to select BAT Alarm option 3 Press ENT to confirm selecting 4 Use the Up Down Arrow to change the value 5 Press ENT to confirm the setting 6 Press EXIT to exit BAT Alarm 41 Language You can choose different language for the menu operation English German French Russian To set the Language 1 Press MENU to enter into menu setting 2 Use the Up Down Arrow to select Language option 3 Press ENT to confirm selecting 4 Use the Up Down Arrow to change the option 5 Press ENT to confirm the setting 6 Press EXIT to exit o o 5 fey m 42 Trouble shooting You are not supposed to fix the handheld or the sensor The product contains no customizable parts On the other hand the waterproof performance is enabled by unique techniques functions of which may be disabled by unau thorized disassembly On this account only professional maintenance personnel properly authorized by the Company are entitled to any repair necessary We have been contacted frequently by our customers req uesting repair service We inspect their products and find many of them are not in need of repair the problem
9. e 35 suggest you turn off the Fish ID and only study the sonar returns which is displayed as archs To set the Fish ID 1 Press MENU to enter into menu 235c setting 2 Use the Up Down Arrow to select Fish ID option 3 Press ENT to confirm selecting 4 Use the Up Down Arrow to change the value 5 Press ENT to confirm the setting 6 Press EXIT to exit Units Units is used to choose depth unit and Temp unit There are four combinations for you to choose the depth unit and Temp unit Fahrenheit Feet Fahrenheit Meter Celsius Feet Celsius Meter 36 To set the Units 1 Press MENU to enter into menu setting 2 Use the Up Down Arrow to select Units option 3 Press ENT to confirm selecting 4 Use the Up Down Arrow to change the value 5 Press ENT to confirm the setting 6 Press EXIT to exit Backlight Backlight is used to let you choose whether the backlight is on or auto in some enviroment To set the Backlight 1 Press MENU to enter into menu setting 2 Use the Up Down Arrow to select Backlight option 3 Press ENT to confirm selecting 37 bd D x a 4 Use the Up Down Arrow to change the value 5 Press ENT to confirm the setting 6 Press EXIT to exit Contrast Contrast is used to let you get a most suitable display when you operate the unit To set the Contrast 1 Press MENU to enter into menu set
10. lowing depth ranges 10 15 30 50 60 80 100 120 and 140 feet When the depth unit is set to meter the fish finder has the following depth ranges 3 5 10 15 20 25 30 35 and 40m Depth range changes or signal loss will cause lines with missing detail and or abrupt changes in the graphed bottom The screen image jump shown here is due to an automatic 26 change in depth New returns graphed at a different scale will not match up with the historic data already graphed at a higher or lower scale 3 Water surface line The water surface line indicate the displayed position of water surface on the screen which is very helpful for you to estimate the depth of Om 7 i detected fish 18 m 225c B For example 4 SS nn the current depth reading is 18 6m and the position A of fish a icon B is about 1 3 of total depth A thus the 1 fish lies on the position 5 _ a about 18 6 1 3 6 2m deep 100 EF 0 20 from water surface Accordingly you could estimate the fish b lies about 1 2 of the A total depth which is 18 6 1 2 9 3m 27 Underwater conditions vary greatly so some experience is needed to get the most benefits of FC80 90 Use the message displayed in the screen as a helpful tools for your judgment thus you could exert the full function of FC80 90 28 Operation Menu Operation Instruction The menu setting is convenient and friendly You can get various fu
11. may scratch the surface Additionally give daily attention to ensure the screen is keep away from any chemicals 48 Guarantee Conditions 1 We assure you this product 15 free from defects in materials and workmanship The warranty coverage is One Year from the date of purchase during which if the unit fails to perform as described in the product s written specifications we will repair or replace it free of charge As for products exceeding the warranty coverage the maintenance department will charge customers some fees according to the real situation 2 This warranty is void if damage or malfunction is due to abuse misuse accident failure to reasonably maintain improper installation or use or unauthorized alteration or repairs Our company retains the final right to judge or repair the defected products 3 Our company holds the right to update the products And it is not obligated for our company to update the former products according to the new standard 49 Specifications and feature 1 Specifications 1 Display Display size 3 0in 76mm FSTN LCD Display Resolution 128 x 64 Pixels Display contrast 0 100 Adjustable Range Backlight On Auto Visible under strong sunlight 2 Sonar amp Radio Depth Capability 1 0 30m Wireless Operating Range Max300m Sonar Frequency 115KHZ Sonar Beam Angle 80deg 10db Radio Frequency 433 9 MHz Sonar Alarms Fish Shallow Low battery FC90 only
12. nction setting by simple operation 1 Power key Power on Power off Note to shut off the unit press the Power key and keep it for 3s then release it 2 Ent key To confirm a setting hold the screen Note when the unit is n working pressing Ent key will freeze the screen which is A helpful for you to carefully study the underwater condition 90 EL 0 20 29 Note when you enter into a menu setting pressing Ent key then you are able to change the setting and the frame line of current menu will look thicker then non setting see following u non setting setting To exit the setting condition press ENT key again 3 MENU amp EXIT key to enter or exit menu setting 4 Up arrow down arrow key to increase decrease the setting value 30 Sensitivity Sensitivity determines how echoes will be displayed on the screen Increasing the sensitivity will make you see more details on the screen In such situations when you see too much clutter on the screen decreasing the sensitivity will play an effect The larger the sensitivity is the more relatively strong sonar returns the screen will display If the sensitivity is decreased too low most sonar returns which maybe fish will not be displayed In situation while water is clear or very deep try increasing the sensitivity which will let you see even the very weak re
13. ower is switched on Be sure the battery s positive and negative poles are corr ectly oriented in the holder Also check if the battery has enough capacity 3 When using the device in shallow water areas the screen does not display things normally and depths are not indicated with consistency The sensor has a perfect performance in water from 4 to 100 feet 1 2 30m deep Abnormal display inconsistent depths may occur when used in areas with depth less than 1 2m Try to use it in deeper waters 4 The picture displayed on the screen vibrates and the sea bed contour has abrupt changes The picture vibrates because the sea bottom depth being scanned is changing Since the depth range used by the 45 current test signal and by the previous test signal differs plus the varying height of the sea bed contour pictures displayed on the screen will occupy different heights causing the vibrating phenomenon 5 Nothing appears on the display even you can see fish under the sensor a Oil dirt and fuel might cause a film to form on the sensor and reduce its effectiveness Cleaning the surface of the transducer might help b Blectrical noise nearby can interfere with the sonar which will cause some weaker signals being elimin ated 6 The display become so cluttered that you even could not achieve a clear bottom Such cluttered display maybe caused because a The water is too low b The water is too turbid c
14. ry can be used for power supply without any interference Note correctly connect the control box to the bait boat battery then you can monitor the remained voltage of your bait boat all the time Avoiding using under a low battery Note the range of battery monitoring is 5 2 15v 16 Warnning be careful not reversing connection of positive and negative pole to the bait boat battery black wire is for negative pole black amp white wire is for positive pole 10 assemble the bait boat With the above steps were finished carefully assemble your bait boat then the complete set of bait boat amp wireless fish finder is ready to use Note sometimes you may need a switch to control on off of the RemoteEye see the packing list page2 1 Drill a hole on your bait boat hull of housing tighten the switch bait boat on the bait boat 2 connect the switch to the power cable conect to 17 power cable RemoteEye installation method 2 As the structure of bait boats is different sometimes maybe you prefer mounting the sensor to your bait boat in other method see the following example Mounting the sensor on the bottom hull of the bait boat Note for such installation method finding a proper mounting location for the sensor is very important Otherwise an unproper mounting position may cause a short Remote Control distance or abnormal display on the screen 18 Sonar working method When sonar work
15. s the signals were remited in the direct ion as instructed below A b A B So in the area A and area B there should be no any obstacle otherwise the sonar signals will be blocked thus sonar unit will not be able to receive the signal normally which will cause short Remote Control distance or abnormal display on the screen For example in the following sensor mounting figure Aisright B is wrong 19 a In the A mounting position the sonar signals can be remitted without any obstacle in the two direction b In the B mounting position the sonar signals can not be remitted normally as they are blocked by the hull of the bait boat 20 1 Find a proper mounting position and drill 3 holes on the bottom of your bait boat 3 holes D L Note the 3 holes should be drilled with the following dimension 41 6 mm 21 2 Hold the sensor calbe through the 12mm hole Note please spread some sealed glue on the screws before fixing the sensor 22 4 Spread some sealed glue to the drilled location preventing water leakage happening 5 Carry out the following steps same with step 6 10 instructed in RemoteEye installatiion method 1 23 Operational Panel Basic 10 11 12 13 14 1 Transducer plug 7 Depth Range T di model 8 Sensitivity Reading epth Reading 9 Battery Strength 3 Water surface line 2 p M M 5 4
16. s occur because some customers are not very acquainted with product usage And we are forced to label these products as inapplicable for maintenance and return them to the customers Therefore in the event of problems during product use we invite you to read the following trouble shooting part carefully before you send the product for maintenance 43 1 No signal on screen If the fishfinder fails to receive signals from the sensor it will stop updating the screen which will then remain unchanged Under any circumstances if the handheld can not receive signals transmitted by the sensor or the sensor is out water for several seconds the screen will seem the same until the sensor is placed in water again and signals are restored 1 FC80 90 is a product depending upon line of sight Obstacles between the handheld and the sensor can con tribute to signal loss 2 FC80 90 has a detection depth ranging from 1 to 100 feet 0 3 30m Incorrect readings may appear in water areas with depth less than 0 3m Additionally consider ing the sonar physical characters we suggest you avoid using the product in swimming pools or small sized enclosed water areas 3 The maximum remote control distance for the sensor reaches 1000 feet 300m If the sensor with the bait boat 44 moves out of the range inconsistent signals or even no signals will be transmitted to the handheld 2 Nothing is displayed after the handheld s p
17. ss ENT to confirm the setting 6 Press EXIT to exit Shallow 33 Depth Range Depth Range determine in which portion the bottom will display in the screen For example if the actual depth is 10m and the current Depth Range is 20m then the bottom will display on 5096 portion of the screen To set the Depth Range 1 Press MENU to enter into menu setting 2 Use the Up Down Arrow to select Depth Range option 3 Press ENT to confirm selecting 4 Use the Up Down Arrow to change the value 5 Press ENT to confirm the setting 6 Press EXIT to exit 34 Fish ID Fish ID control the way the detected target is displayed on the screen 1 If Fish ID is on a fish icon will be displayed when some fish and other object is detected 2 If Fish ID is off a arch will be displayed on the screen IN Fish ID is On Fish ID is Off Note your sonar unit is advanced however it can not distinguish between fish and other suspended objects such as turtles trotlines submerged floats air bubbles etc One word it could be fooled So you may see fish icon on the screen actually there is no fish underwater However the Fish ID is very helpful for you to take some of the work out of studying the screen That means Fish ID provides you a tool to distinguish the fish in a max possibility and omits other negligible sonar information To know as more as possible what s under your boat w
18. the control box As sometimes you may have to mount the antenna on your bait boat instead of connect 7 it directly to the control box Thus it will be convenient for you to find enough space to place the control box at a proper position Tool List not included Hand drill 5 32 drill bits Phillips and flat head screwdriver Marine sealant RemoteEye installation method 1 1 Make a supporting plate to hold the wireless sensor The shape of supporting plate may be different according to the shape of your bait boat Note the shape below is just for your reference 2 Find a proper position and drill two holes on the top cover of your bait boat as figured below il 7 Note The hole is used to be through the sensor cable the diameter should be about 11 5mm The hole 2 is used to mount the antenna the diameter should be about 5 8mm 3 Monut the antenna on the top cover of your bait boat mount the antenna extended cable to the top cover There are two connector of the antenna extended cable one is used to connetct to the antenna another is used to connect to the control box connect to control box connect to antenna Firstly take out the screw from the antenna extended cable then hold one end of the cable through the hull of bait boat as instructed below Finallly tighten the screw hull of bait boat screw 10
19. the water then you are ready to enjoy the operation Two ways of using the product Installing the battery Warning do not split the battery cover with strength in the vertical direction To take off the battery cover press it and slide in the indicated direction 1 Turn the screw anti clockwise with a screw driver Then slide the battery cover towards the bottom of the unit and remove it from the main housing 2 Install 4 batteries Be certain that the batteries are aligned as per the diagram within the battery compartment 3 Slide the battery cover towards the top of the unit until it is completely closed Then turn the screw clockwise 5 Install the RemoteEye to bait boat The picture below is a overall installation instrution showing you the general conception to install the control amp sonar system namely RemoteEye to the bait boat which is just for your reference Note the selected bait boat here is just for your reference the installation way may vary according to the structure of different bait boats Introduction of the RemoteEye RemoteEye indicates the whole set of electric amp sonar control system It is used to be mounted on your bait boat 1 Control box 2 Wireless sensor 3 Antenna 4 Antenna extended cable 5 Switch of on off controlling for RemoteEye optional 6 Power cable Note the antenna extended cable is used to connect the antenna and
20. ting 2 Use the Up Down Arrow to select Contrast option 3 Press ENT to confirm selecting 4 Use the Up Down Arrow to increase decrease the value N 6 be 5 Press ENT to confirm the setting 6 Press EXIT to exit 38 Load DFT Load DFT is used to restore to the factory settings To set the Load DFT 1 Press MENU to enter into menu setting 2 Use the Up Down Arrow to select Load DFT option 3 Press ENT to confirm selecting 4 Use the Up Down Arrow to change the option a cs ES 5 Press ENT to confirm the setting 6 Press EXIT to exit 39 Monitor SEL FC90 Fishfinder only Monitor SEL is used to detect the remained voltage of the bait boat and Water or Air temperature 16 m 235c AT a T ANI r 2 5 vh x 1 gt Air Temp Water Temp To set the Monitor SEL 1 Press MENU to enter into menu setting 2 Use the Up Down Arrow to select Monitor SEL option 3 Press ENT to confirm selecting 4 Use the Up Down Arrow to change the option 5 Press ENT to confirm the setting 6 Press EXIT to exit 40 BAT Alarm FC90 Fishfinder only When the bait boat battery is lower then the voltage setting the FC90 fishfinder will z sound an alarm tone and a VTG LOW warning message will appear on the screen Set a warning value for battery alarming and when the alarm tone
21. turns However in situation while water is turbid try decreasing the sensitivity which will make only the useful echo be showed on the screen and the noise will be omitted To set the Sensitivity 31 1 Press MENU to enter into menu setting 2 Use the Up Down Arrow to select Sensitivity option 3 Press ENT to confirm selecting 4 Use the Up Down Arrow to increase decrease the value 5 Press ENT to confirm the setting 6 Press EXIT to exit Channel Channel make it possible for you to switch using between the wireless model and another wire model NAKI8850B provided that you have bought one CHI for FC80 90 CH2 for NAKI8850B To set the Channel 1 Press MENU to enter into menu setting 2 Use the Up Down Arrow to select Channel option 3 Press ENT to confirm selecting 32 4 Use the Up Down Arrow to change the value 5 Press ENT to confirm the setting 6 Press EXIT to exit Shallow The Fishfinder sound an alarm tone when the bottom goes shallower or equal than the alarm s setting You also could exit alarm mode by enter into Shallow menu and artificially increase the current depth alarm value to a safe grade To set the Shallow 1 Press MENU to enter into menu setting 2 Use the Up Down Arrow to select Shallow option 3 Press ENT to confirm selecting 4 Use the Up Down Arrow to increase decrease the value 5 Pre
Download Pdf Manuals
Related Search