“Registering Your Handset” in Chapter 7
Contents
1. Press Clear to make corrections 4 Press Yes to confirm The settings will reset Your handset s power switches off It will switch back on in a few seconds after updating all the settings Registering Your Handset Registration lets your base unit and handsets communicate Your handset must be linked to the base in order to make calls and to use many of features on the phone Your handset is already registered unless you have bought an extra handset individually or you have de registered a handset For additional handsets see Registering Your Handset s with an Additional Base on page 7 5 If the handset is not registered it displays Unregistered Note Your base unit can register up to four handsets After registering four handsets your base unit registration memory is full If you try to register an additional handset the registration process will not complete Follow the steps below to register your handset 1 Press Menu gt Settings gt Handset gt Register 2 Enter the system PIN Default 0000 Press Clear to make corrections 3 Press Enter to confirm Your handset starts searching for the base 4 Press on the base unit until the LED starts flashing 5 The handset registers to the particular base unit and shows the signal icon EH 7 4 Settings and Maintenance v1 0 November 2006 Cordless Internet Phone with Skype Model SPH200D User Manual Registering Your Handset s with an Additi2. 6 Cordless Internet Phone with Skype Model SPH200D User Manual To select recall duration follow these steps 1 Press Menu gt Settings gt Advanced gt Landline gt Recall 2 Scroll to the new setting and press OK The new setting is saved Setting a Pause A pause is a break you can enter when making a call A pause is used for calls such as PABX and operator services Your phone supports different pause durations For details consult your service provider To set the pause follow these steps 1 Press Menu gt Settings gt Advanced gt Landline gt Pause 2 Scroll to the new setting 3 Press OK The new setting is saved Category Number This section only applies to models with Category number support Some telephone providers send a category number along with the CallerID Consult your service provider on category number handling To call back from the history properly change setting to Yes if your telephone service provider sends out a category number or change setting to No if the category number is not sent To set the category number follow these steps 1 Press Menu gt Settings gt Advanced gt Landline gt Cat Number 2 Scroll to the new setting and press OK The new setting is saved Settings and Maintenance 7 7 v1 0 November 2006 Cordless Internet Phone with Skype Model SPH200D User Manual Network Settings This section describes the information on viewing and changing the Internet network se
3. Chapter 7 Settings and Maintenance Settings Use the Settings menu to change call settings and settings for the handset tt Settings Call Settings Privacy Tones Screen Select Figure 7 1 Country Code The country code is the international calling code for a country for example 1 for Canada When you first set up the handset you entered a country code To change the country code 1 Press Menu gt Settings gt Call Settings gt Country Code 2 Edit the country code Press Clear to make corrections 3 Press OK when finished The new setting is saved Note After you set up your country code your handset s power switches off It will switch back on in a few seconds after updating the country settings 7 1 v1 0 November 2006 Cordless Internet Phone with Skype Model SPH200D User Manual Area Code The area code feature automatically adds or removes the area code of an outgoing call based on the country setting for the handset You can define an area code up to five digits Note The country code must be correct for the area code feature to work properly See Setting up the Handset in Chapter 2 To set the area code follow these steps 1 Press Menu gt Settings gt Call Settings gt Area Code 2 Enter your area code or press Clear to erase it 3 Press OK when finished The new setting is saved Time and Date Set the time zone before i
4. Settings and Maintenance 7 11 v1 0 November 2006 Cordless Internet Phone with Skype Model SPH200D User Manual 7 12 v1 0 November 2006 Settings and Maintenance
5. can configure some of the network settings Skype settings system upgrade and administrative settings from the Web page You do not need to configure most of these settings after setting up the phone This section is recommended for advanced users only Note Incorrect network settings will affect Skype usage on this phone Consult your network administrator or service provider before making any changes to the network settings Accessing the Web Page Minimum System Requirements The minimum system requirements to access the Web page are e SPH200D set e Router e Computer with a Web browser e Internet connection Make sure that your phone is properly connected and set up sharing the same network with your computer as shown below phone landline socket I SRANAN Pa BI NiTeeap power supply Internet router by Figure 7 2 Settings and Maintenance 7 9 v1 0 November 2006 Cordless Internet Phone with Skype Model SPH200D User Manual Accessing the Web Page To access the Web page follow these steps 1 Open a Web browser 2 Enter your phone s IP address at the address bar An authentication window pops up G Tip To find your phone s IP address see Viewing Network Settings on page 7 8 3 Enter the user name and password The default user name is admin and the default password is password After verifying your user name and password you wi
6. erly Try again Charging contacts may be dirty Clean contacts with a damp cloth Turn on the handset tone See Personalizing Your Handset Display in Chapter 6 e Switch on the handset s power See Powering Your Handset On and Off in Chapter 1 Handset on the charger does not The battery may be defective Purchase new batteries from your charge dealer e Check that the batteries are inserted correctly Make sure that the handset is placed properly on the charger The battery icon is animated while charging No display e Check that the battery is charged e Check the connections Bad audio crackles echo The handset may be nearly out of range Move closer The phone may be interfered by nearby electrical appliance Move the base unit to a different location The phone may be at a location with thick walls Move the base unit to a different location Handset does not ring Check that the handset ringer is turned on See Personalizing Your Handset Display in Chapter 6 Caller ID does not display e Caller ID service may not be activated Check with your service provider The caller s information may be withheld or unavailable Cannot make or answer a second Second call service may not be activated Check with your service call provider e For landline calling check that the recall selection is correct See Recall Selection on page 7 6
7. ll see the configuration home page e Home page The home page shows your current system and network settings e Network page The network page shows your current Internet connection type and Ethernet speed You can make changes to these settings on this page e Skype page The Skype page shows your current Skype status You can create a new Skype account or sign in to Skype from this page e System page You can upgrade your phone s operating system from this page You will first need to download the latest software from the NETGEAR Web page at www netgear com e Administration page You can change the Web page access password on this page You can also reset your phone to factory default feature and network settings Troubleshooting Table 7 1 Troubleshooting Tips Problem Tip No dial tone on landline e Check the phone and power connections The handset may be out of range Move closer The battery capacity may be low Charge battery Signal icon flashing The handset may be out of range Move closer If the handset displays Unregistered it is not registered Register the handset See Registering Your Handset on page 7 4 7 10 Settings and Maintenance v1 0 November 2006 Cordless Internet Phone with Skype Model SPH200D User Manual Table 7 1 Troubleshooting Tips continued No parking tone e Check the power connections of the charger The handset may not be placed prop
8. nitial use of the phone Once you have connected to the Internet your phone updates the clock automatically according to your time zone setting After resetting the phone you may have to set the time zone again Note If you use this menu to set the time or date manually your phone will use this new setting It will stop automatic update until your base power is reset To set the time and date follow these steps 1 Press Menu gt Settings gt Time amp Date You can adjust these settings Time You do not need to set the time If you set the Time Zone then the phone will automatically find the time on the Internet Time Zone GMT Greenwich Mean Time or the number of hours or for GMT Daylight Time Choose Standard or Daylight Time Daylight Savings Time Time Format Choose 12 hour or 24 hour Time Separator The time separator is a symbol such as a colon that separates the hour and minute i e 18 30 Your phone supports two styles colon and period 7 2 Settings and Maintenance v1 0 November 2006 Cordless Internet Phone with Skype Model SPH200D User Manual e Date Format Month Day Year The default is MM DD YYYY e Date Separator The date separator is a symbol such as a slash that separates the month day and year for example 08 25 2006 Your phone supports three styles slash colon and period 2 Press OK when finished The new setting is saved Note Automa
9. onal Base Note Make sure that you have configured the language country code and area code of you phone before registering extra handsets This section shows you how to register your handset to additional base units If your handset displays Unregistered see to Registering Your Handset on page 7 4 1 Press Menu gt Settings gt Handset gt Register 2 Enter the system PIN Default 0000 Press Clear to make corrections 3 Press Enter to confirm Your handset starts searching for the base 4 Press on the base unit until the LED starts flashing Selecting a Base Unit You can switch your handset between different base units if your handset has registered to these base units You can set up the handset to automatically connect to the closest base unit You can also set up the handset to only connect to a fixed base unit you have specified Note Your handset must be registered to a base unit before you can select that base unit 1 Press Menu gt Settings gt Handset gt Base 2 Scroll to the base unit that you want or select Auto if you want your handset to automatically connect to the closet base unit 3 Press Select The new setting is saved Deleting a Handset Use one handset to delete de register another handset that shares the same base unit 1 Press Menu gt Settings gt Handset gt De register Settings and Maintenance 7 5 v1 0 November 2006 Cordless Internet Phone with Sky
10. pe Model SPH200D User Manual 2 Scroll to the handset number that you want to delete Press Enter a Tip The handset number displays beside the word Skype during standby For 7 i example Skype 1 Enter the system PIN Press Clear to make corrections 4 Press Enter The handset is deleted Advanced Landline Calling Features This section describes the call related features that apply to the landline only Dial Mode Dial mode is the telephone signal used in your country Your phone supports tone DTMF and pulse rotary dialing During installation you set up your phone for use in your country For details consult your service provider To go to dial mode follow these steps 1 Press Menu gt Settings gt Advanced gt Landline gt Dial Mode 2 Scroll to the new setting 3 Press OK The new setting is saved A tone mode The display shows d Digits entered after the d are sent out as tone Tip If your phone is set to pulse dialing press and hold during a call for temporary i signals on this call only Recall Selection Recall is a signal that is sent when using some of the calling features such as making or answering a second call Your phone supports different recall signals You can make changes depending on the requirements Your phone is already set up for use in your country For details consult your service provider 7 6 Settings and Maintenance v1 0 November 200
11. tic Update Once you have connected to the Internet your phone updates the clock automatically according to your time zone setting Changing the System PIN The system PIN is used for registering deleting handsets and protecting the access rights to some of the other menus The default system PIN is 0000 You can personalize the PIN for greater security 1 Press Menu gt Settings gt Handset gt Change PIN Enter the system PIN Press Enter to confirm Press Clear to make corrections Enter the new system PIN Press Enter Re enter the new system PIN again for verification MR of Press Enter The new setting is saved Note Write down your PIN and save it for future use If you have forgotten the PIN call your manufacturer for assistance Resetting to Default Settings The default settings are the original factory settings of your phone You can reset your phone settings to factory default These settings are shown in Default Factory Settings in Appendix A You can reset all the settings but keep the network settings 1 Press Menu gt Settings gt Advanced gt Reset Device 2 Scroll and select either Reset All or Keep Network Settings and Maintenance 7 3 v1 0 November 2006 Cordless Internet Phone with Skype Model SPH200D User Manual e Reset All Reset all the settings including the network settings e Keep Network Reset all the settings except the network settings Enter the system PIN
12. ttings of your phone You do not need to configure the network after setting up the phone This section is recommended for advanced users who want to configure the network with their static IP Internet Protocol address Note Incorrect network settings will affect Skype usage on this phone Consult your network administrator or service provider before making any changes to the network settings Viewing Network Settings To view the network settings follow these steps 1 Press Menu gt Settings gt Information 2 Scroll to view the information Changing Network Settings To change the network settings follow these steps 1 Press Menu gt Settings gt Network 2 Scroll and select the setting that you want and follow the onscreen instructions e DHCP The Cordless Internet Phone uses Dynamic Host Configuration Protocol DHCP by default which is correct for most customers If you configure a static IP this disables DHCP Press Back when finished e PPPoE If your Internet service provider requires you to use Point to Point Protocol over Ethernet PPPoE you can configure your user name and password for the PPPoE connection e Static IP You can configure the network to use a static IP e Reset Network This resets the network with the changes that you made 7 8 Settings and Maintenance v1 0 November 2006 Cordless Internet Phone with Skype Model SPH200D User Manual Web Page Configuration You
Download Pdf Manuals
Related Search