Home

Manual - Gefen

1. set preset name 4 BR2Out2 PRESET4 NAME IS ASSIGNED TO BR2Out2 page 117 Advanced Operation Commands set_saturation The set saturation command sets the color saturation level for the video signal on the specified input Use the show saturation command to display the current saturation value Syntax set saturation paraml param2 Parameters param1 Input 1 4 param2 Level 0 100 Example set saturation 1 65 INPUT1 IS SET TO SATURATION 65 page 118 Advanced Operation Commands set_telnet_ pass The set_ telnet pass command sets the Telnet password The value of param1 cannot exceed 10 characters in length Syntax set telnet pass parami Parameters param1 Password Example set telnet pass b055man TELNET INTERFACE PASSWORD IS SET b055man page 119 Advanced Operation Commands set_ telnet port The set_ telnet port command sets the Telnet listening port The matrix must be rebooted after executing this command The default port setting is 23 Use the show telnet port command to display the current Telnet listening port Syntax set telnet port paraml Parameters param 1 Port eC 1 1024 Example set_ telnet port 24 TELNET PORT 24 IS SET set telnet user The set telnet user command creates a Telnet username Syntax set telnet user paraml Parameters param1 Username Example set telnet user bo55man TELNET INTERFACE USERNAME IS SE
2. FACTORY DEFAULT EXT HD SL 444 FW V2 34 FACTORY DEFAULT NOT BY WEBGUI IP 192 168 1 72 Netmask 255 255 255 0 Gateway 192 168 1 1 page 91 Advanced Operation Commands help The help command displays the list of available RS 232 Telnet commands Help ona specific command can be displayed when using paraml1 Syntax help paraml Parameters param1 Command name optional Example help sipadd SET IP ADDRESS FOR STATIC CMD SET IPADD PARAM1 PARAM ddd ddd ddd ddd page 92 Advanced Operation Commands hdp pulse The hpd pulse command cycles the HPD line on the specified input Issuing this command is identical to physically disconnecting and reconnecting the cable between the source and the matrix Syntax hpd pulse paraml Parameters param1 Input 1 4 Examples hpd pulse 1 HPD PULSE HAS BEEN SENT TO INPUT page 93 Advanced Operation Commands lock edid The lock edid command secures the Local EDID by disabling the automatic loading of the downstream EDID when the matrix is powered Syntax lock edid parami Parameters param1 Value 0 1 Value Description 0 Disable 1 Enable Examples lock edid 0 MATRIX EDID IS UNLOCKED lock edid 1 MATRIX EDID IS LOCKED page 94 Advanced Operation Commands lock matrix The lock matrix command locks unlocks the matrix When the matrix is locked all functions are disabled including the
3. User Manual Release A9 Ax4 Seamless Matrix for HDMI Important Safety Instructions 10 11 12 13 14 15 GENERAL SAFETY INFORMATION Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this product near water Clean only with a dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install or place this product near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer To reduce the risk of electric shock and or damage to this product never handle or touch this unit or power cord if your hands are wet or damp Do not expose this product to rain or moisture Unplug this apparatus during lightning storms or when unused for long period
4. i re si Info Display Enables On or disables Off the Info window If set to Off the Info window is never displayed Brief Info This option controls what is displayed when Info Display set to On If Brief Info is set to On then only the In and Out routing information is displayed If Brief Info is set to Off then the resolution information is also displayed page 41 Operating the 4x4 Seamless Matrix for HDMI Menu System HDCP Some sources e g computers will enable HDCP if an HDCP compliant display is detected Inputs can be set to accept or not accept HDCP content Outputs can be set to follow pass through the input setting or set to always on 1 Press the Menu button on the front panel or on the IR remote control The menu system will be displayed iefen J 2 Press the Select button to display the Setup Menu If using the IR remote press the OK button 3 Use the A or V buttons to highlight HDCP iefen J 4 Press the Select button to display the HDCP menu ACCEPT FOLLOW INPUT page 42 Operating the 4x4 Seamless Matrix for HDMI Menu System 5 Use the A or V buttons to highlight either the Input or Output option 6 Press the Select button to select the desired option If using the IR remote press the OK button efend ACCEPT 7 Use the lt or gt buttons to change the value ACCEPT ALWAYS ON Input Accept or Not Accept Use the Accept option to all
5. Press the Select button to accept the current changes If using the IR remote control press the OK button IP Mode Set this option to either Static or DHCP If using the Static option the IP address must be specified Use the Byte1 Byte2 Byte3 and Byte4 options to set each of the digits in the IP address subnet mask and gateway Type Select Use this option to switch between the IP address IP subnet mask Mask and gateway Gate Byte Use the Byte1 Byte2 Byte3 and Byte4 options to set each of the digits in the IP address subnet mask and gateway Re link Use this option to attempt to re link to the network using the current IP settings page 47 Operating the 4x4 Seamless Matrix for HDMI Menu System STATIC IP 192 168 Timeout Sets the time out period in seconds when using the Re Link option to link with the network using the current IP settings HTTP Port Sets the HTTP listening port for the 4x4 Seamless Matrix for HDMI Restore Default This option will reset the default IP settings for the 4x4 Seamless Matrix for HDMI page 48 Operating the 4x4 Seamless Matrix for HDMI Menu System Changing the Telnet Settings 1 Press the Menu button on the front panel or on the IR remote control The menu system will be displayed 2 Usethe A or Y buttons to highlight the Network option efeng 3 Press the Select button to display the Network menu If using the IR remote press the OK bu
6. Reset All Select Output to adjust Select the desired output from the drop down list Brightness Use the slider control to adjust the brightness of the output The brightness value can also be entered directly in the value field Contrast Use the slider control to adjust the contrast of the output The contrast value can also be entered directly in the value field Saturation Use the slider control to adjust the saturation of the output The saturation value can also be entered directly in the value field Hue Use the slider control to adjust the hue The hue value can also be entered directly in the value field Reset All Click this button to reset values to factory default settings page 69 Operating the 4x4 Seamless Matrix for HDMI Web Interface Manage EDID gt Assign Lock EDID Secures the Local EDID and disables automatic EDID loading during power up If the Lock EDID button is clicked enabled the EDID locked on power cycle message will be displayed in red The local EDID information will now be locked once the matrix is rebooted Click the Unlock EDID button to disable the Lock EDID feature Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Manage EDID Network System Power ST Y 7 Melp Log Qut Uptoad Downiosd Copy EDID From Bank_1 Copy EDID To Please select from the inputs below Copy EDID From Select the EDID from the drop down list The EDID will be copied from the Output or sele
7. See Routing Inputs to Outputs for more information page 18 Operating the 4x4 Seamless Matrix for HDMI Routing Basics Using the IR Remote Control 1 Press the button of the desired output to be masked For this example we will select Output 3 Mask button Press Out 3 2 Press the Mask button 3 Both the selected output and the M LED indicator will be illuminated on the front panel of the matrix Output 3 is masked Output 3 is selected 4 Tounmask an output press the button for the output and then select the desired input See Routing Inputs to Outputs for more information page 19 Operating the 4x4 Seamless Matrix for HDMI Routing Basics Saving Routing Presets The 4x4 Seamless Matrix for HDMI allows routing states to be saved to any of 10 preset memory locations Presets are retained in memory even if the matrix is powered OFF Cig NOTE Routing presets cannot be saved using the IR remote control unit 1 Create the desired routing state In the example above we have masked Output 1 and set Input 2 to Output 2 Input 3 to Output 3 and so on Note that when saving a routing state any outputs that are masked are also saved to memory 2 Le s save this configuration to Preset 1 Press and hold button 1 on the Routing Presets section on the front panel Press and hold button 1 3 After a few seconds button 1 will turn on and remain illuminated indicating that t
8. param2 Output 0 1 4 Examples r31 INPUT 3 IS ROUTED TO WINDOW OUTPUT 1 r 10 INPUT 1 IS ROUTED TO ALL WINDOW OUTPUTS page 147 Advanced Operation Commands S The s command routes the specified input to all outputs Do not precede this command with the symbol Also see the r command Syntax S parami Parameters param1 Input 1 4 Example s 1 INPUT 1 IS ROUTED TO ALL WINDOW OUTPUTS page 148 This page left intentionally blank This page left intentionally blank 04 Appendix Appendix Default Settings MAC Address IP Address Subnet Mask Default Gateway HTTP Listening Port Telnet Listning Port Telnet TCP Access UDP Port Enable UDP Access Remote UDP IP Address Remote UDP Port Remote UDP Access Gefen Syner G Discovery Gefen Syner G Discovery Mode Gefen Syner G Show Device Output Names A V Input Names HDCP Pass Through each input HDCP each output IR Channel Preset Names Device dependent cannot be modified 192 168 1 72 255 255 255 0 192 168 1 1 80 23 Enabled 50007 Disabled 192 168 1 255 50008 Disabled Enabled Read Write Hide Me Output1 Output4 Input1 Input4 Accept Follow Input 1 Preset_A Preset_J page 152 Appendix Upgrading the Firmware 10 Using the Web Interface A IMPORTANT DO NOT power off or disconnect the AC power cord from the matrix at any time during the firmware upgrade process
9. routing preset See Saving Routing Presets for more information 4 Menu System Controls Use these buttons to select and change settings within the built in menu system See Menu System for more information 5 This IR sensor receives signals from the included IR remote control unit 6 Lock Use this button to lock the matrix and prevent accidental changes See Locking Unlocking the Matrix for more information on this feature 7 Standby LED Indicator This LED will remain illuminated when the matrix is powered OFF 8 Power This button is used to power ON and power OFF the matrix This button will remain illuminated while the matrix is powered ON page 2 Getting Started Panel Layout Back 4 IP Cont 5 USB 6 RS 232 12V DC N Connect the included IR Extender Gefen part no EXT RMT EXTIRN to this port Connect up to four Hi Def sources to these inputs using the included HDMI cables Connect up to four HDTV displays to these HDMI outputs Connect an Ethernet cable between this jack and a LAN to use IP control See RS 232 and IP Configuration for details on using IP control Not used Reserved for future expansion Connect an RS 232 cable from this port to an RS 232 device See RS 232 and IP Configuration for more information on setting up RS 232 serial control Connect the included 12V DC power supply from this power receptacle to an available AC electrical outlet Do not o
10. EDID Name HD SL 444 HD SL 444 HD SL 444 HD SL 444 HD SL 444 HD SL 444 HD SL 444 HD SL 444 Select All Banks Copy Cancel Copy To Place a check mark in the desired check box to select the desired bank where the EDID will be copied Remove the check mark to deselect the bank Bank The number of the bank Name The name of the bank Select All Banks Place a check mark in this check box to select all banks Remove the check mark to deselect all banks Copy Press this button to execute the copy operation Cancel Clears all check marks from each box page 73 Operating the 4x4 Seamless Matrix for HDMI Web Interface Manage EDID gt Bank Names Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Main VO Setup Manage EDID Network System Power STANDBY Help Log Out Bank Names Upload Download Edit Bank Names Bank Bank Indicates the EDID bank number Name Type the desired name of the EDID bank in this field Save Saves the current name change to the EDID bank s Cancel Restores the previous name or each bank if the name was edited page 74 Operating the 4x4 Seamless Matrix for HDMI Web Interface Manage EDID gt Upload Download Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Main VO Setup Manage EDID Network System Power STANDBY Help Log Out Upload EDID select EDID File to Upload Browse select Bank Location Bank_1 Upload Browse Click this bu
11. IR remote press the OK button 4 Use the A or V buttons to highlight the UDP Settings option efend 5 Press the Select button again to display the UDP Settings menu If using the IR remote press the OK button ENABLE 507 192 168 2 213 508 page 51 Operating the 4x4 Seamless Matrix for HDMI Menu System 5 Use the A or V buttons to highlight the option to change The UDP Access option will be highlighted automatically 6 Once the desired option is highlighted press the Select button to select it If using the IR remote control press the OK button When an option is selected its current value will be highlighted in orange ENABLE LEP 168 2 213 508 7 Use the lt or gt buttons to change the current value 8 Press the Select button to accept the current changes If using the IR remote control press the OK button UDP Access Enables or disables UDP access to the HD Video Wall Controller UDP Port Sets the UDP port for the 4x4 Seamless Matrix for HDMI Byte Use the Byte1 Byte2 Byte3 and Byte4 options to set the IP address of the digits in the UDP IP address subnet mask and gateway Remote UDP Port Sets the remote UDP listening port for the 4x4 Seamless Matrix for HDMI page 52 Operating the 4x4 Seamless Matrix for HDMI Menu System System Settings 1 Press the Menu button on the front panel or on the IR remote control The menu system will be displaye
12. IS AND ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE vi Features and Packing List Features e Seamless matrix scales each of its four inputs and routes them to any or all of the four outputs without frame loss Input and Output resolutions up to 1080p Full HD and 1920x1200 WUXGA e HDCP compliant Seamless switching ensures no switching delay and no picture loss during transitions e Ten user configurable routing presets can be accessed via front panel push buttons e Controllable via front panel controls IR IP web server interface Telnet and UDP and RS 232 e Easy to use on screen Graphical User Interface GUI Handheld IR remote control and IR Extender input on back panel e Field upgradable firmware via web server interface USB port reserved for future product enhancements e Locking power supply connector 1U t
13. The LED next to the Power button on the front panel indicates the power state of the 4x4 Seamless Matrix for HDMI In standby mode power is being supplied to the 4x4 Seamless Matrix for HDMI but the unit is not turned on This LED will be red and remain illuminated as long as the unit is in standby mode lf this LED does not illuminate check the connection between the power receptacle on the 4x4 Seamless Matrix for HDMI and the AC outlet Red LED indicates that matrix is in standby mode Turning on the 4x4 Seamless Matrix for HDMI Press the Power button to power on the matrix The Power button will turn blue and remain illuminated as long as the matrix is powered on To power off the 4x4 Seamless Matrix for HDMI and return to standby mode press the Power button again LED indicator turns off Power button is illuminated page 14 Routing Basics Determining the Current Routing State On the top left portion of the matrix there are four sets of five LED indicators Each set of five LED indicators resides above each of the four Output buttons LED indicators 1 through 4 represent each input on the matrix If one of these LED indicators are illuminated then that means that the input is active The M LED indicates that the output is masked Refer to Masking Unmasking Outputs for more information on masking and unmasking outputs Each of the Output buttons are used to route inputs to outputs When an Output butto
14. access 1 TELNET ACCESS IS ENABLED page 143 Advanced Operation Commands use_telnet pass The use telnet pass command forces the password credentials for each Telnet session The default setting is disabled Use the set telnet pass command to set the Telnet password Syntax use telnet pass parami Parameters param1 Value 0 1 Value Description O Disable password L Enable password Example use telnet pass 1 TELNET INTERFACE PASSWORD IS ENABLED page 144 Advanced Operation Commands use udp access The use udp access command enables or disables UDP access The default setting is disabled Syntax use udp access parami Parameters param1 Value 0 1 Value Description 0 Disable UDP access 1 Enable UDP access Example use udp access 1 UDP ACCESS IS ENABLED page 145 Advanced Operation Commands m The m command displays the current routing status of the matrix Masking and locking status of the matrix is also provided Do not precede the m command with the symbol Syntax m Parameters None Example m OUT IN e N N w w sous page 146 Advanced Operation Commands r The r command routes the specified input to the output Do not precede this command with the symbol Also see the s command If param2 Q then the specified input param7 will be routed to all outputs Syntax r paraml param2 Parameters param1 Input 1 4
15. be displayed jefen 7 2 Press the Select button to display the Setup Menu If using the IR remote press the OK button 3 Use the A or V buttons to highlight Picture Settings ofend 4 Press the Select button to display the Picture Settings menu If using the IR remote press the OK button 5 The Out Select option should be highlighted If not use the A or VW buttons to highlight it Each output can have individual saturation settings Therefore the output must be selected before making changes to it page 34 Operating the 4x4 Seamless Matrix for HDMI Menu System 6 Press the Select button to select the Out Select option The currently selected output will be highlighted in orange 7 Select the desired output using the lt or gt buttons ofend 8 Press the Select button to accept the current output selection 9 Use the A or V buttons to highlight the Saturation option 10 Press the Select button to select the Saturation option 11 Change the saturation value using the lt or gt buttons 12 Press the Select button to accept the change page 35 Operating the 4x4 Seamless Matrix for HDMI Menu System Adjusting the Hue 1 Press the Menu button on the front panel or on the IR remote control The menu system will be displayed jefen 7 2 Press the Select button to display the Setup Menu If using the IR remote press the OK button 3 Use the A or V buttons to high
16. change page 16 Operating the 4x4 Seamless Matrix for HDMI Routing Basics Using the IR Remote Control We ll use with the same routing example that is outlined on the previous page However instead of using the buttons on the front panel we will use the IR remote control Input 2 is routed to Output 2 We will use the IR remote to route Input 4 to Output 2 1 Point the IR remote at the IR sensor on the front panel of the matrix 2 Select the desired output In this example we will select Output 2 Always select the output before selecting the input Press Out 2 Press In 4 3 Select the desired input In this example we will select Input 4 Input 4 is selected 4 The LED indicator for Input 4 is now illuminated Input 4 is now routed to Output 2 page 17 Operating the 4x4 Seamless Matrix for HDMI Routing Basics Masking Unmasking Outputs Masking prevents the output device display etc from receiving an output signal Instead of powering down or disconnecting the output device individual or multiple outputs can be masked Using the Front Panel Buttons 1 Press the button of the desired output to be masked For this example we will select Output 2 Output 2 is selected 2 Continue pressing the button for Output 2 until the M LED indicator is illuminated Output 2 is masked 3 To unmask an output press the button for the output and select the desired input
17. for HDMI EXT HD SL 444 Power STANDBY 7 heip Log Out Firmware Update UI ver V2 34 Browse Update IR Channel Factory Reset Reboot Reboot Browse Click this button to select the firmware file to be uploaded See Upgrading the Firmware for more information Update Click this button to begin the update process once the firmware file is selected IR Channel Click this drop down list to set the desired IR channel for the matrix The matrix and the included IR remote control must be set to the same channel in order to work properly Options O wae 3 Reset Click this button to set the matrix to factory default settings The TCP IP settings are preserved Reboot Click this button to reboot the matrix page 82 This page left intentionally blank This page left intentionally blank 03 Advanced Operation RS 232 and IP Configuration Using Telnet 1 Launch the desired terminal application For example on the Windows operation system we can use Hyperterminal on Mac OS X we can use the Terminal application 2 In this example we will use Terminal in Mac OS X At the command prompt type the following telnet ip address where ip address is the IP address of the switcher 3 After correct settings have been used in the terminal program information similar to the following will be displayed Welcome to EXT HD SL 444 TELNET telnet gt 4 Type help for a list of commands or refer to the ta
18. 44 VO Setup Manage EDID Network System eo o Power STANDEY Heip Log Out Lock Matrix Inputs Input Preset 8 Preset Preset F Peets Preset Proset Preset Save amp Recall Routing Presets Save Routing Preset Preset_A Save Recall Routing Preset Preset_A Presetl Preset_B Preset2 Preset_C Preset3 Preset_D Preset4 Preset_E Preset Preset_F Preset Preset_G Preset Preset_H Presets Preset_ Preset9 Preset_ J Presetl0 Save Routing Preset Saves the current routing state to memory Click the drop down list to select the desired routing preset Click the Save button to save the preset to memory Recall Routing Preset Loads the selected routing state into memory Click the desired Preset button to load a routing preset page 58 Operating the 4x4 Seamless Matrix for HDMI Web Interface Main gt I O Status Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Main VO Setup Manage EDID Network System Power STANDSY Heip Log Our Output Name Outputs RSENSE On On Mask 1 1 HPD ig High HDCP Active Inactive Name Displays the name of the output The name of the output can be changed using the set output name command or through the I O Setup gt I O Names page of the Web interface RSENSE Displays the current Rsense state Mask Displays the masking state of each output HPD Displays the Hot Plug Detect HPD state of each output HDCP Indicates if HDCP detection is enabled or dis
19. 5 0 Gateway 10 5 64 1 page 99 Advanced Operation Commands recall preset The recall preset command loads the routing preset Syntax recall preset paraml Parameters param1 Preset 1 10 Example recall preset 2 INPUT 4 IS ROUTED TO WINDOW OUTPUT 1 RECALL ROUTING STATE PRESET 2 reset picture The reset picture command resets all picture settings to factory default Syntax reset picture Parameters None Example reset picture PICTURE SETTINGS HAVE BEEN SET TO DEFAULTS page 100 Advanced Operation Commands save preset The save preset command saves the current routing state to a specified preset Syntax save preset paraml Parameters param1 Preset 1 10 Example save preset 1 CURRENT ROUTING STATE IS SAVED TO PRESET 1 set bank name The set_ bank name command names the specified bank Syntax set bank name paraml param2 Parameters param1 Bank 1 8 param2 Name Example set bank name 5 Dell 24 BANK5 NAME IS ASSIGNED TO Dell24 page 101 Advanced Operation Commands set_brightness The set brightness command sets the brightness level of the video signal on the specified input Syntax set brightness paraml param2 Parameters param1 Input 1 4 param2 Level 0 100 Examples set brightness 1 65 INPUT1 IS SET TO BRIGHTNESS VALUE 65 set_contrast The set_contrast command sets the contrast level of the v
20. 5 64 123 00 1C 91 04 60 63 EXT HD MVSL 441 10 5 64 131 00 10 91 03 B0 1C EXT HDKVM LAN S 10 5 64 23 00 10 91 03 C1 28 EXT HD SL 444 10 5 54 134 04 10791703 60 00 3 Under the Device Settings section select either Static or DHCP from the IP Mode drop down list gt gt Select Static to manual enter the IP address subnet mask and gateway IP Consult with your network administrator if necessary Select DHCP to let the DHCP server automatically assign the IP address subnet mask and gateway IP Device Settings IP Mode DHCP Web GUI Part 80 Telnet Port 23 Firmware Version V234 Hardware Version W22 page 10 Getting Started Installation 4 Click the Save button at the bottom of the screen Device Settings IP Mode Web GUI Port Telnet Port 23 Firmware Version Y2 34 Hardware Version V2 2 Description EXT HD SL 444 5 The unit will automatically reboot and use the new network settings 6 Use the IP address of the switcher to access the built in web interface or start a Telnet session See the following for more information gt Web Interface gt RS 232 and IP Configuration page 11 This page left intentionally blank 02 Operating the 4x4 Seamless Matrix for HDMI Operating the 4x4 Seamless Matrix for HDMI Introduction Standby Mode
21. Download the firmware update from the Support section of the Gefen Web site Extract the firmware file from the ZIP file Power ON the 4x4 Seamless Matrix for HDMI Connect an Ethernet cable between the matrix and the computer running the Web interface It is unnecessary to disconnect any cables or extenders from the 4x4 Seamless Matrix for HDMI during the update process Click the Configuration tab in the Web interface and click the Browse button under the System Configuration section Select the firmware file and click the Update button The matrix will display a prompt to verify that the current firmware will be overwritten Click the OK button on the dialog box to begin uploading the firmware file The 4x4 Seamless Matrix for HDMI will begin the upgrade process This process will take several minutes The upgrade process may be monitored using the RS 232 interface After the 4x4 Seamless Matrix for HDMI has been updated the unit will automatically reboot After the 4x4 Seamless Matrix for HDMI reboots the firmware upgrade process will be complete page 153 Resolutions max Appendix Specifications 1080p Full HD Maximum Pixel Clock Preset Select Buttons Output Select Buttons Menu Button Menu Control Buttons On Standby Button Standby Indicator Input Indicators Video Input Video Output RS 232 IP Control USB IR Extender Power Power Input Power Consumption Dimensions W x H x D
22. Matrix for HDMI Menu System 5 Use the A or V buttons to highlight the option to change The Position option will be highlighted automatically POSITION H OFFSET V OFFSET MENU TIMEOUT INFO TIMEOUT INFO DISPLAY BRIEF INFO BACK EXIT 6 Once the desired option is highlighted press the Select button to select it If using the IR remote control press the OK button When an option is selected its current value will be highlighted in orange Use the lt or gt buttons to change the value Position Assigns the display where the OSD will be displayed when the Menu button is pressed page 39 Operating the 4x4 Seamless Matrix for HDMI Menu System H Offset The horizontal offset of the OSD as it appears on the display eiiim ot Ke li fl ar ri V Offset The vertical offset of the OSD as it appears on the display page 40 Operating the 4x4 Seamless Matrix for HDMI Menu System Menu Timeout Once the Menu button is pressed the OSD will appear Menu Timeout is the duration in seconds of the OSD before it is automatically hidden If set to Off then the OSD must be hidden manually by pressing the Menu button Info Timeout By default each display will show an information info window This window displays the input and output resolution Menu Timeout is the duration in seconds of the OSD before it is automatically hidden OUT 1 720p60 IN 1 720p60 gt o e REN dasi
23. Max Color Depth 8 bit Mode DVI HDMI HDMI Max Audio Channels 2 Ch Monitor Name HD SL 444 Info Display Place a check mark in this box to show display information on the outputs Choose EDID Select the EDID from the drop down list The selected EDID will be copied from the Output or selected EDID Bank to the desired input s and used by the source Options Bankl Bank8 1 Outputl 4 Output4 page 61 Operating the 4x4 Seamless Matrix for HDMI Web Interface Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Heip Audio Formats LPCM DTS HD DTS Digital Surround Dolby Digital AC3 Dolby TrueHD Feature Audio Formats The matrix reads the audio block from the EDID and displays the capabilities of the display sink The word TRUE denotes that the display sink supports the audio format Otherwise it is marked as FALSE page 62 Operating the 4x4 Seamless Matrix for HDMI Web Interface I O Setup gt Preset Names Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 VO Setup Manage EDID Network System at s VO Names HPD Control HOCP Video Edit Preset Names Preset Name Preset_A Preset_B Preset_C Preset_D Preset_E Preset_F Pre set_G Preset_H Preset_ Preset_ Cancel Preset The number of each preset Name Type the desired name of each preset in these fields Save Saves the current changes to the name of the preset s Cancel Restores the previous
24. Seamless Matrix for HDMI Menu System Using the IR Remote Control The IR remote control has buttons which represent the controls on the front panel Use the lt gt A and Y buttons to move around within the menu system Press the A and V buttons to move up and down Press the lt or gt buttons to change the value of the current selection Press the OK button to make the desired selection The current selection will be highlighted in green Press to select the highlighted menu item Press the A and YW buttons to move up and down within the menu system page 27 Operating the 4x4 Seamless Matrix for HDMI Menu System Setting the Output Resolution Ee NOTE Before changing this setting make sure that all connected displays can support the selected output resolution 1 Press the Menu button on the front panel or on the IR remote control The menu system will be displayed Press the Select button If using the IR remote press the OK button 3 Press the Select button again to enter the Output Resolution menu If using the IR remote press the OK button page 28 Operating the 4x4 Seamless Matrix for HDMI Menu System 4 Usethe A or Y buttons to highlight the desired output resolution 5 Press the Select button to apply the highlighted resolution If using the IR remote press the OK button If the display does not support the selected resolution use the fadefault command to reset the 4
25. T boS5man page 120 Advanced Operation Commands set_udp port The set_udp port command sets the UDP communication port Use the show udp port command to display the current UDP communication port Syntax set udp port parami Parameters param1 Port 1 1024 Example set udp port 1002 UDP COMMUNICATION PORT 1002 IS SET PLEASE REBOOT THE UNIT page 121 Advanced Operation Commands set_udp remote ip The set udp remote ip command sets the remote UDP IP address The IP address must be specified using dot decimal notation The default UDP remote IP address is 192 168 1 255 The matrix must be rebooted after executing this command Use the show udp remote ip command to display the current remote UDP IP address Syntax set udp remote ip paraml Parameters param 1 UDP address Example set udp remote ip 192 168 1 227 UDP REMOTE IP ADDRESS 192 168 1 227 page 122 Advanced Operation Commands set_ udp remote port The set_ udp remote port command sets the remote UDP listening port The default remote UDP listening port is 50008 The matrix must be rebooted after executing this command Use the show udp remote port command to display the current remote UDP listening port Syntax set udp remote port paraml Parameters param 1 Port 0 65535 Example set udp remote port 50008 REMOTE UDP COMMUNICATION PORT 50008 IS SET page 123 Advanced Operation Commands
26. The set output command sets the output resolution The specified output resolution is applied to all outputs Use the show output command to display the current output resolution Syntax set output paraml Parameters param 1 Example set output 4 OUTPUT RESOLUTION IS SET TO Value Value Of OoO7FywryIT AOI ATION e Ha a m R F gt m F OY O1 a OO NO a Hi J 1 17 Description 480p 576p 720p 50 Hz 720p 60 Hz 1080p 24 Hz 1080p 50 Hz 1080p 60 Hz 1024 x 768 1280 x 800 1280 x 1024 1366 x 768 1440 x 900 1600 x 900 1600 x 1200 1680 x 1050 1920 x 1200 Native 720p60 page 115 Advanced Operation Commands set output name The set_ output name command assigns a name to the output on the matrix The name of the output is limited to 15 characters Names longer than 15 characters will be truncated Syntax set output name paraml param2 Parameters param1 Output 1 4 param2 Name Example set output name 3 Sony XBR OUTPUT3 NAME IS ASSIGNED TO Sony XBR page 116 Advanced Operation Commands set preset name The set preset name command assigns a name to the specified preset The name of the preset is limited to 8 characters Names longer than 8 characters will be truncated To display the name of a preset use the show preset name command Syntax set preset name paraml param2 Parameters param1 Preset 1 10 param2 Name Example
27. Unit Weight 1920 x 1200 WUXGA 225 MHz 10 x Tact type blue backlight 4 x Tact type blue backlight 1 x Tact type blue backlight 6 x Tact type blue backlight 1 x Tact type blue backlight 1 x LED red 20 x LED blue 4 x HDMI Type A 19 pin female locking 4 x HDMI Type A 19 pin female locking 1 x DB 9 female 1 x RJ 45 Mini B 1 x 3 5mm mini stereo Locking type 12V DC 24W max 16 9 x 1 7 x 7 9 480mm x 42mm x 200mm 5 0 Ibs 2 3 kg page 154 This page left intentionally blank Stretch It Switch It Split It Gefen s Got It 20600 Nordhoff St Chatsworth CA 91311 1 800 545 6900 818 772 9100 fax 818 772 9120 www gefen com support gefen com Gs 6 X CE ne This product uses UL or CE listed power supplies
28. abled on each output page 59 Gefen 4x4 Seamless Matrix for HDMI VO Setup Manage EDID Network System VO Status Display Into Input Name Color Depth Color Space HDCP Active Signal Vertical Resolution Horizontal Resolution Progressive Interlaced Refresh Rate Video Mode Name Operating the 4x4 Seamless Matrix for HDMI Web Interface EXT HD SL 444 Power STANDSY Help Log Our Input 10bit RGB Yes No 1024 768 i p 60Hz 120Hz DVI HDMI Displays the name of the input The name of the input can be changed using the Set input name command or through the I O Setup gt I O Names page of the Web interface Color Depth The color depth of the source signal Color Space The color space of the source signal Vertical Resolution The vertical resolution of the source signal Progressive Interlaced The field order of the input signal Refresh Rate The refresh rate of the input signal HDCP The HDCP state of the source signal Active Signal Indicates if there is a source connected to the input Horizontal Resolution The horizontal resolution of the source signal Video Mode The video mode HDMI DVI of the input page 60 Operating the 4x4 Seamless Matrix for HDMI Web Interface Main gt Display Info Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Info Display Choose EDID Bank _1 Feature 24Hz Frame Rate TRUE Max Resolution 1080P 60Hz
29. access Syntax show tcp access Parameters None Example show tcp access TELNET ACCESS IS DISABLED page 137 Advanced Operation Commands show_telnet port The show telnet port command displays the current Telnet port Use the set telnet port command to set the Telnet port Syntax show telnet port Parameters None Example show telnet port TELNET PORT IS 23 show_udp access The show_udp access command displays the current UDP access state enabled or disabled Use the use udp access command to enable or disable UDP access Syntax show udp access Parameters None Example show udp access UDP ACCESS IS DISABLED page 138 Advanced Operation Commands show_udp port The show udp port command displays the current UDP serial port Use the set udp port command to set the UDP serial port Syntax show udp serport Parameters None Example show udp serport UDP SERVER PORT IS 1002 show_udp remote ip The show udp remote ip command displays the current remote UDP IP address Use the set_ udp remote ip command to set the remote UDP IP address Syntax show udp remote port Parameters None Example show udp remote port REMOTE UDP COMMUNICATION PORT IS 508 page 139 Advanced Operation Commands show_udp remote port The show_udp remote port command displays the current remote UDP port Use the set udp remote port command to
30. all rack mountable enclosure rack ears included H MI 7080p Seg HIGH DEFINITION MULTIMEDIA INTERFACE PROGRESSIVE Cc oO M B LIANT cover o 3 o 2 E iy ES a gt Olisi Gol SYNER G Packing List The 4x4 Seamless Matrix for HDMI ships with the items listed below If any of these items are not present in your box when you first open it immediately contact your dealer or Gefen 4x4 Seamless Matrix for HDMI 4 x 6 ft Locking HDMI Cables 1 x 6 ft DB 9 Cable 1 x IR Extender Module e 1 x IR Remote Control 1 x 12V DC Locking Power Supply 1 x Set of Rack Ears 1 x Quick Start Guide vii 4x4 Seamless Matrix for HDMI Table of Contents 01 02 Getting Started Paner L VOUT sess rates E E E E E 2 EEE a AETAT T T T A TE A AE E TA T E 2 BE aE E E E A E 3 IR Remote Conmrol UNIE gicccns ass crcensctassennenenssntsncaimatmsasaunseneenssnantonetnansumonnennenwscnactass 4 ODD PEET TEETE EET E E E A EE AT A T T 4 BONON es E E E E 6 BaNG C OV E eresas a EE EE A EE EE E 6 installing the Ballers sccacssstantcinuiscaitcuntavlaitaanittrsanmas neoini iriton irai 7 Batey COVE nesr a 7 Setting th IR Channel ascscessesantctoevanedanrasionsatabentectnnesquijnaetiivetentanteeaeontancemeneiavent 8 MAON a E E veh fang 1ePatenaa i vednnstadtaor 9 Connecting the 4x4 Seamless Matrix for HDMI ccccccesesseeeeeeeeneeeeees 9 Sample Wiring Diagram s5 c6 lt sincxacrnernceciaec ie aanidocsotaebaenth an
31. amless Matrix for HDMI Web Interface I O Setup gt HDCP NOTE Some sources e g computers will enable HDCP if an Ee HDCP compliant display is detected Check the box under the Disable column to force the computer to ignore detection of an HDCP compliant display The Disable feature does not decrypt HDCP content Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Power STANDBY Heip Log Out HDCP Pass Through Inputs Input Name inputi Accept Do Not Accept Input2 Accept Do Not Accept Input3 Accept Do Not Accept Input Accept Do Not Accept All Inputs Accept Do Not Accept Input The number of the input Name The name of the input The name of each input can be changed using the Set input name command or through the I O Setup gt I O Names page of the Web interface Accept Not Accept Click the Accept button to allow HDCP content to pass on the input Click the Do Not Accept button to prevent HDCP content from being transmitted to the input To change all inputs to Accept at once click the Accept button in the row labeled All Inputs To change all outputs to Do Not Accept at once click the Do Not Accept button in the row labeled All Inputs page 66 Operating the 4x4 Seamless Matrix for HDMI Web Interface Output Name Output Always On Follow Input Output Always On Follow Input Outputs Always On Follow Input Output Always On Follow Input All Outputs Always O
32. arameters None Example show output OUTPUT RESOLUTION IS SET TO 720p60 page 134 Advanced Operation Commands show_output_ name The show_output name command displays the name of the specified output Use the set output name to assign a name to an output Syntax show output name Parameters param1 Output 1 4 Example show output name 3 THE NAME FOR OUTPUT3 IS Sony XBR show power The show power command displays the current power state Use the power command to power ON or power OFF the matrix Syntax show power Parameters None Example show power POWER IS ON page 135 Advanced Operation Commands show_preset_ name The show_preset name command displays the name for the specified preset To assign a name to a preset use the set preset name command Syntax show preset name parami Parameters param1 Preset 1 10 Example show preset name 4 THE NAME FOR PRESET4 IS BR2 Out2 show saturation The show saturation command displays the saturation for all outputs Use the set saturation command to set the output resolution Syntax show saturation Parameters None Example show saturation OUT A SATURATION VALUE 65 page 136 Advanced Operation Commands show_tcp access The show_tcp access command displays the current TCP access state enabled or disabled Use the use tcp access command to enable or disable TCP
33. ax set gateway paraml Parameters param Gateway Example set gateway 192 168 1 5 GATEWAY 192 168 1 5 page 107 Advanced Operation Commands set_hdcp The set_hdcp command sets the HDCP state for the inputs outputs Syntax set hdcp paraml param2 param3 Parameters param1 Value 0 1 Output param2 Value 0 4 0 All 1 Input 1 2 Input 2 3 Input 3 d Input 4 param3 Value 0 1 Accept Follow Input Not Accept Always On continued on next page page 108 Advanced Operation Commands The meaning of param3 changes depending upon the value specified by param7 For example if param1 0 then the HDCP settings will affect the inputs Setting param3 0 will result in setting the specified input to Accept If param3 1 then the input will be set to Not Accept Conversely if param1 1 then the HDCP settings will affect the outputs Setting param3 0 will result in the affecting the outputs If param3 0 then the specified output will be set to Follow Input If param3 1 then the specified input will be set to Always On Examples set hdcp 0 2 1 HDCP INPUT2 IS SET TO NOT ACCEPT set hdcp 1 1 0 HDCP OUTPUTI IS SET TO FOLLOW INPUT set hdcp 0 0 1 ALL HDCP INPUTS ARE SET TO NOT ACCEPT page 109 Advanced Operation Commands set_http port The set_ http port command specifies the Web server listening port The matrix must be r
34. bles on the following pages Using RS 232 1 Launch the desired terminal application 2 Selected the desired COM port 3 Configure the RS 232 port to the following settings Only TxD RxD and GND pins are used Baud rate 19200 Data bits 8 Parity None Stop bits 1 Hardware flow control None 4 Connect to the RS 232 port 5 Type help fora list of commands or refer to the tables on the following pages page 86 Advanced Operation RS 232 and IP Configuration UDP Configuration The 4x4 Seamless Matrix for HDMI also supports the UDP protocol To configure UDP settings click the Network tab within the Web interface See Network for more information on available UDP settings NOTE Depending upon the network all related IP Telnet and Ee UDP settings will need to be assigned Consult your network administrator to obtain the proper settings page 87 Advanced Operation Commands display_telnet_welcome fadefault help hdp pulse lock edid lock matrix mask mute power reboot recall preset reset picture save preset set bank name set brightness set_ contrast set device descr set_edid set eth relink set gateway set hdcp set http port set hue set input name set ipadd set ipmode set ir set netmask set output set output name set preset name set saturation set_ telnet pass set telnet port set telnet user Enables disables the Telne
35. cted EDID bank to the destination Options Bank 1 Bank 8 Outputl Output4 page 70 Operating the 4x4 Seamless Matrix for HDMI Web Interface Copy To Inputs Place a check mark in the desired check box Copy To EDID Modes to select or deselect the desired input s Internal 1080p 2 chau Internal 1080p 2 chau Internal 1080p 2 chau Internal 1080p 2 chau EDID Modes Select the EDID mode from the drop down list Options Internal 1080p 2 ch audio Internal 1080p Multi ch External Outputl Custom User Select All Inputs Place a check mark in this check box to select all inputs Remove the check mark to deselect all inputs page 71 Operating the 4x4 Seamless Matrix for HDMI Web Interface Input Name EDID Source EDID Name Inputt INT 1 HD SL 444 Input INT 1 HD SL 444 Inputs INT 4 HD SL 444 Input4 INT 1 HD SL 444 Input The number of the input Name The name of the input The name of the input can be changed using the Set input name command or through the I O Setup gt I O Names page of the Web interface EDID Source The current EDID source being used EDID Name The name of the EDID page 72 Operating the 4x4 Seamless Matrix for HDMI Web Interface Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Network Syste m Power STANDBY Heip Log Out Name Bank_1 Bank 2 Bank 3 Bank_4 Bank_5 Bank 6 Bank_ Bank_ amp
36. d 2 Use the A or Y buttons to highlight the System option iefen J 3 Press the Select button to display the System menu If using the IR remote press the OK button efeng 4 Usethe A or Y buttons to highlight the desired option 5 Press the Select button to make the selection If using the IR remote control press the OK button page 53 Operating the 4x4 Seamless Matrix for HDMI Web Interface Using the built in Web Interface Access the built in Web interface by entering the IP address of the 4x1 Multiview Seamless Switcher for HDMI in a browser window See Network Configuration using Syner G for more information on obtaining the IP address of the matrix Once connected to the switcher the login screen will be displayed Username Administrator Password eeeee Gefen 4x4 Seamless Matrix f r HDMI EXT HD SL 444 Username Select the username from the drop down list Options Operator Administrator Administrator login provides unrestricted access to all features and settings Operator login limits access to matrix routing display information and routing preset features Password Enter the password for the associated username The default password is Admin The password can also be set using RS 232 or Telnet See the set webui_ad_pass andthe set webui_ op pass commands The password is masked when it is entered page 54 Operating the 4x4 Seamless Matrix for HDMI Web Interface Th
37. e Web GUI is divided into four main pages Main I O Setup Manage EDID and Configuration Each main page is represented by a tab at the top most portion of the screen The Main I O Setup and Manage EDID pages have their own set of sub tabs Click on the desired tab sub tab to open the desired page ij NOTE In order to view all four tabs at the top of the screen the user must be logged in as Administrator If logged in as Operator only the Main tab will be visible Main gt Routing Power STANDBY Help Log Out Gefen 4x4 Seamless Matrix for HDMI VO Setup Manage EDID Network System Power Click this button to toggle the power state of the matrix When the matrix is powered on the button will read STANDBY Help Click the Help button to display context sensitive help This button is available on all main pages Log Out Click Log Out to terminate the current Web session are return to the login page page 55 Operating the 4x4 Seamless Matrix for HDMI Web Interface Name Outputs The name of the output The name of the output can also be changed using the Set output name command or through the I O Setup gt I O Names page of the Web interface Output Outputs Check to select the desired output for routing Input Inputs Click the radio button next to the desired input to be routed Name Inputs The name of the input This name can be changed using the Set input na
38. ebooted after executing this command The default port setting is 80 Use the show http port command to display the current HTTP listening port Syntax set http port paraml Parameters param1 Port 1 1024 Example set http port 82 HTTP PORT 82 IS SET set_hue The set_ hue command sets the hue for the video signal on the specified input Syntax set hue paraml param2 Parameters param1 Input 1 4 param2 Value 0 100 Example set hue 1 30 INPUT1I IS SET TO HUE 30 page 110 Advanced Operation Commands set_input_ name The set input name command assigns a name to the specified input The value of param2 cannot exceed 8 characters in length Syntax set input name paraml param2 Parameters param1 Input 1 4 param2 Name Example set input name 3 Blu ray INPUT3 NAME IS ASSIGNED TO Blu ray set_ ipadd The set_ipadd command sets the IP address of the matrix The IP address must be entered using dot decimal notation The matrix must be rebooted after executing this command The default IP address is 192 168 1 72 Use the show ipconfig command to display the current IP address of the matrix Syntax set ipadd paraml Parameters param 1 IP address Example tset ipadd 192 166 1190 IP ADDRESS 192 168 1 190 page 111 Advanced Operation Commands set_ipmode The set_ipmode command sets the IP mode to DHCP or static The matrix must be rebooted afte
39. ee ener e enter teen cen tn eee re eeneen eet 68 Manage EDID Assign ivecctanintenianicusinmmtebantinientaaaiosenlantemniuntecsniuetesiaiectania 70 Manage EDID gt Bank Names ccccccccccsssssecceesseecneeseeeseeseeeseeseeeseees 74 Manage EDID Upload DOWiNO AG ss is5ccsis ccisssacecoasestocrcceveawauex eacttacsiexdecee 75 PS ois See anne ae ete Rc ieia Sora bec nia iken ei eab keniense 77 SU se ester scien AN E AE A AA A nhac 81 Advanced Operation RS 232 and P COnMGUPAUOM seserinis eiee e a nE 86 Gemo To NE raea a E E 86 Br e pe a A E E E A E E A E ee EE 86 UDP Conig rato persain eain beei ia a ONE i Ei 87 COMIN S A EE EES 88 Appendix BB ro U aes 21 8 cee en een aie cee one ee me ne ene ere ere 152 Upgrading VE AVA tars et er etre et toucante waiters god ad inch tend decd elmeatateheatanel san 153 Using the Web Inlet ex cic cac sere cvewse cscont adevten sateen i aeia 153 Specifications iscedio sirenes nennt esn I Eres IRERE ERANS T EAREN AAEE EE PARERE EE RRES KE NENS 154 This page left intentionally blank 01 Getting Started Getting Started Panel Layout Front These blue LED indicators display the state of each input See Routing Basics for more information Input Indicators 2 Output Selection Buttons Press these buttons to select the desired 1 4 output See Routing Basics for more information 3 Routing Presets 1 10 Press these buttons to select the desired
40. emote UDP IP address in this field Destination UDP Port Enter the remote UDP listening port in this field page 79 Operating the 4x4 Seamless Matrix for HDMI Web Interface Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Main VO Setup Manage EDID Network System Heip Log Out Web Login Settings Username Administrator Old Password New Password Confirm New Password Set Network Defaults Username Click this drop down list to select the user name The password for the selected user name can be changed if desired Old Password Type the current old password in this field New Password Type the new password in this field Confirm Password Re type the new password in this field Set Network Defaults Click to reset the network settings to factory default Save Click this button to save any network changes made on this page page 80 Operating the 4x4 Seamless Matrix for HDMI Web Interface Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Download Current Configuration Download Restore Configuration Browse Warning All current settings will be lost Download Click this button to download the current matrix configuration to a file Browse Click this button to select the configuration file to be uploaded Restore Uploads the selected configuration file to the matrix page 81 Operating the 4x4 Seamless Matrix for HDMI Web Interface Gefen 4x4 Seamless Matrix
41. erves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing in the United States and other countries 2015 Gefen LLC All Rights Reserved All trademarks are the property of their respective owners IV Operating Notes e When using the 4x4 Seamless Matrix for HDMI for the first time it is recommended that the unit be configured using the Gefen Syner G Software Suite Download the application here http www gefen com synerg 4x4 Seamless Matrix for HDMI Licensing lwIP is licenced under the BSD licence Copyright c 2001 2004 Swedish Institute of Computer Science All rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the above copyright notice this list of conditions and the following disclaimer 2 Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution 3 The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission THIS SOFTWARE IS PROVIDED BY THE AUTHOR AS
42. front panel RS 232 and Telnet Syntax lock matrix paraml Parameters param1 Value 0 1 Value Description 0 Unlock 1 Lock Example lock matrix 1 MATRIX IS LOCKED page 95 Advanced Operation Commands mask The mask command masks the video on the specified output s Use the unmask command to disable output masking If param1 0 then all outputs are masked Syntax mask parami Parameters param1 Output 0 4 Examples mask 1 OUTPUT A IS MASKED mask 0 ALL OUTPUTS ARE MASKED page 96 Advanced Operation Commands mute The mute command enables disables audio muting on all outputs Syntax mute parami Parameters param1 Value 0 1 Value Description 0 Unlock 1 Lock Example mute 1 AUDIO IS MUTED page 97 Advanced Operation Commands power The power command toggles power on the matrix Syntax power parami Parameters param1 Value 0 1 Value Description 0 Off 1 On Examples power 0 POWER IS OFF power 1 POWER IS ON page 98 Advanced Operation Commands reboot The reboot command reboots the matrix Executing this command is the equivalent of disconnecting and reconnecting the AC power cord on the back of the matrix The matrix must be rebooted after changing any of the IP settings Syntax reboot Parameters None Example reboot DEVICE HAS BEEN REBOOTED EXT HD SL 444 FW V2 34 IP 10 5 64 214 Netmask 255 255 25
43. he current routing configuration has been saved Preset is saved page 20 Operating the 4x4 Seamless Matrix for HDMI 1 2 T Routing Basics Loading Routing Presets Using the Front Panel Buttons Press the desired Routing Preset button The routing preset will be loaded into memory In the example below we have selected Routing Preset 3 Preset 3 is loaded EEMEER E Le a amp The selected button will remain illuminated as long as the preset is selected Using the IR Remote Control Press the desired Preset button on the IR remote control Note that the buttons below button 7 and 9 are not used Preset buttons The routing preset will be loaded into memory The associated Routing Preset button on the matrix will remain illuminated as long as the preset is selected page 21 Locking Unlocking the Matrix Locking the matrix will prevent any changes by disabling all buttons except the Lock button on the front panel This feature is useful in preventing routing or other changes caused by accidentally bumping or pressing the buttons on the front panel Using the Front Panel Buttons 1 Press and hold the Lock button on the front panel The Lock button will begin to flash 2 Continue holding down the Lock button until it stops flashing 3 The matrix is now locked The Lock button will remain illuminated as long as the matrix is locked Matrix is locked 4 To unlock the matri
44. he same audio and video capabilities 3 Press the Select button to accept the current selection If using the IR remote press the OK button 4 Use the lt or gt buttons to select either Yes or No 5 Press the Select button to save the changes If using the IR remote press the OK button 6 The display will flash momentarily The EDID from the selected output will be copied to the input and will be used by all outputs page 45 Operating the 4x4 Seamless Matrix for HDMI Menu System Changing the IP Settings 1 Press the Menu button on the front panel or on the IR remote control The menu system will be displayed 2 Usethe A or Y buttons to highlight the Network option efeng 3 Press the Select button to display the Network menu If using the IR remote press the OK button efend 4 Press the Enter button again to display the IP Settings menu If using the IR remote press the OK button STATIC IP 192 168 155 page 46 Operating the 4x4 Seamless Matrix for HDMI Menu System 5 Use the A or V buttons to highlight the option to change The IP Mode option will be highlighted automatically 6 Once the desired option is highlighted press the Select button to select it If using the IR remote control press the OK button When an option is selected its current value will be highlighted in orange STATIC 7 Use the lt or gt buttons to change the current value 8
45. i Def sources to the input ports In 1 In 4 ports on the matrix 2 Connect up to four HD displays using the output ports Out 1 Out 4 on the matrix 3 OPTIONAL Connect an Ethernet cable from the IP Control port on the matrix to a Local Area Network LAN 4 OPTIONAL Connect an RS 232 cable from the RS 232 port on the matrix to the RS 232 connector on the Automation Control Device 5 OPTIONAL Connect the included IR extender to the IR Ext port on the matrix 6 Connect the included 12V DC locking power supply to the power receptacle on the matrix Do not overtighten the locking power connector 7 Connect the power supply to an available electrical outlet Sample Wiring Diagram l gt HDMI CABLE ource RS 232 CABLE ME GEF EN ii CAT 5 CABLE EEE HD Source IR IN Po HD Source 4x4 Seamless HD Source Matrix for HDMI LAN oD for IP Control 4 d Automation Control Device L HD Displays IR Extender j gt EXT RMT EXTIRN ME EXT HD SL 444 page 9 Getting Started Installation Network Configuration using Syner G 1 Connect the matrix to the network and launch the Gefen Syner G application Download the application here http www gefen com synerg 2 Select the EXT HD SL 444 from the list of products under the Discover tab onmoure 10 5 64 90 00 1D 09 7EE11F IP Address EXT HDKVM LAN 5 10 5 64 130 82 1 D E8 273 B27 A5 EXT CU LAN 10 5 64 124 00 10 91 04760 0C EXT CU LAN 10
46. ideo signal on the specified input Syntax set contrast paraml param2 Parameters param1 Input 1 4 param2 Level 0 100 Examples set contrast 1 74 INPUT1 IS SET TO CONTRAST VALUE 74 page 102 Advanced Operation Commands set device descr The set_ device descr command assigns a name to the switcher This is useful when there are multiple devices on a network and you want to give them different names e g Conf Rm Wall Unit 1 etc The value of param7 cannot exceed 30 characters in length The default name is EXT HD SL 444 Syntax set device descr paraml Parameters param 1 Name Examples set device descr Matrix 1 DEVICE DESCRIPTION NAME IS SET TO Matrix 1 page 103 Advanced Operation Commands set_edid The set_ edid command sets the specified EDID type to an input or bank Note that the argument for param2 is dependent upon the value of param1 Similarly the argument for param4 is dependent upon the value of param3 Syntax set edid paraml param2 param3 param4 Parameters param1 Source Source Description int Uses default Internal EDID bank Uses EDID bank output Uses EDID on Output sink param2 Source 1 8 Source Description L eau 2 1 1080p 2CH 2 1080p Multichannel 1 8 EDID bank I eae d Output When specifying param2 the available arguments will depend upon the value of param1 If p param1 int then param2 must specifiy an internal EDID f
47. in order to claim warranty Customers outside the US are responsible for shipping charges to and from Gefen Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy under the Support section of the Gefen Web site at www gefen com PRODUCT REGISTRATION Please register your product online by visiting the Register Product page under the Support section of the Gefen Web site 4x4 Seamless Matrix for HDMI Contacting Gefen Technical Support Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Email support gefen com Visit us on the Web www gefen com Technical Support Hours 8 00 AM to 5 00 PM Monday Friday Pacific Time 4x4 Seamless Matrix for HDMI is a trademark of Gefen LLC Important Notice Gefen LLC res
48. light Picture Settings jefen J 4 Press the Select button to display the Picture Settings menu If using the IR remote press the OK button 5 The Out Select option should be highlighted If not use the A or VW buttons to highlight it Each output can have individual hue settings Therefore the output must be selected before making changes to it page 36 Operating the 4x4 Seamless Matrix for HDMI Menu System 6 Press the Select button to select the Out Select option The currently selected output will be highlighted in orange 7 Select the desired output using the lt or gt buttons 8 Press the Select button to accept the current output selection 9 Usethe A or Y buttons to highlight the Hue option 10 Press the Select button to select the Hue option 11 Change the hue value using the lt or gt buttons ofend 12 Press the Select button to accept the change page 37 Operating the 4x4 Seamless Matrix for HDMI Menu System OSD Settings The OSD Settings menu controls how the OSD is displayed 1 Press the Menu button on the front panel or on the IR remote control The menu system will be displayed iefen 7 2 Press the Select button to display the Setup Menu If using the IR remote press the OK button 3 Use the A or V buttons to highlight OSD Settings efend 4 Press the Select button to display the OSD Settings menu page 38 Operating the 4x4 Seamless
49. me command or through the I O Setup gt I O Names page of the Web interface Output Status Input Status The outputs that are available for The input that is currently routed to routing the output Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Power STANDBY 2 Help Log Out Outputs Inputs Status Name Output Input Name Output Input Output 1 d inputi 1 Qutput2 2 l Input Output3 3 e Input3 Output4 4 Input4 Mask Unmask Select All Outputs Route Select All Outputs Place a check mark in this box to select all outputs Route Click the Route button to route the selected input to the select output s page 56 Operating the 4x4 Seamless Matrix for HDMI Web Interface Lock Matrix Locks or unlocks the matrix Once the matrix is locked settings cannot be changed using the front panel buttons or through the Web GUI Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 VO Setup Manage EDID Network System 7 Help VO Status Display Info Lock Matrix When the matrix is locked the button text will read Unlock Matrix and a red bar will appear across the top portion of the screen with the text Matrix is LOCKED Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Log Out Unlock Matrix Click the Unlock Matrix button to unlock the matrix page 57 Operating the 4x4 Seamless Matrix for HDMI Web Interface Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 4
50. n Follow Input Always On Follow Input Click the Always On button to allow HDCP to pass through on the output Click the Follow Input button to have the output follow the input setting Accept Not Accept See the previous page for details To change all outputs to Always On at once click the Always On button in the row labeled All Outputs To change all outputs to Follow Input at once click the Follow Input button in the row labeled All Outputs page 67 Operating the 4x4 Seamless Matrix for HDMI Web Interface I O Setup gt Video Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Main VO Setup Manage EDID Network System Power STANDBY 7 heap Log Out Preset Names VONames HPO Control HOCP Video Output Resolution 720P 60H2 Picture Settings Brightness Output Resolution 720P 60Hz al Picture Settings Select input to adjust 1 Inputl a Brightness Contrast Saturation Hue Output Resolution Select the desired output resolution from the drop down list 1280 x 1024 1366 x 768 1440 x 900 1600 x 900 1600 x 1200 1680 x 1050 t920 x 1200 480p 576p 720p 50 Hz 720p 60 Hz 1080p 24 Hz 1080p 50 Hz 1080p 60 Hz 1024 x 768 1280 x 800 Native page 68 Operating the 4x4 Seamless Matrix for HDMI Web Interface Output Resolution 720P 60Hz Picture Settings Select input to adjust Brightness Contrast Saturation Hue
51. n is illuminated it represent the currently selected output For example in the illustration below we can see that Input 1 has been routed to Output 1 LED indicates that Input 1 is the active input Indicates that Output 1 is the currently selected output In addition we can also see that Input 2 is routed to Output 2 Input 3 is routed to Output 3 and Input 4 is routed to Output 4 If the number of the input is the same as the number of the output then this is called the one to one routing state This is the factory default routing state of the matrix page 15 Operating the 4x4 Seamless Matrix for HDMI Routing Basics Routing Inputs to Outputs Using the Front Panel Buttons To change the routing state of an output press and release the button of the desired output to advance to the next input In the illustration below the source connected to Input 2 is currently routed to Output 2 For this example we will route Input 4 to Output 2 1 Select output 2 by pressing button Output 2 The LED for Input 2 is illuminated indi cating that Input 2 is currently routed to Output 2 Output 2 is selected 2 Press button Output 2 twice Input 4 is selected 3 The LED indicator for Input 4 is now illuminated This indicates that Input 4 is now routed to Output 2 Once an output is selected it will remain illuminated until another output is selected An output must be selected before making a routing
52. name or each preset if the name was edited page 63 Operating the 4x4 Seamless Matrix for HDMI Web Interface I O Setup gt I O Names Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Main ip EDID System Power STANDBY 7 Melp Log Out Edit Output amp lnput Names Output Name Input Outputl 1 Output 2 Outputs Output4 Output The ID of the output Name Output Type the desired name of each output in these fields Input The number of each input Name Input Type the desired name of each the input in these fields Save Saves the current changes to the name of the output and or input s Cancel Restores the previous name or each input output if the name was edited page 64 Operating the 4x4 Seamless Matrix for HDMI Web Interface I O Setup gt HPD Control EXT HD SL 444 Gefen 4x4 Seamless Matrix for HDMI Power STANDBY 7 Melp Log Out Pulse Puhe Pulse HPD Control Input Name Inputt Input2 Inputs Inout Input The number of the input Name The name of the input The name of each input can be changed using the Set input name command or through the I O Setup gt I O Names page of the Web interface Pulse Click the Pulse button to cycle the HPD line on the desired input This is the equivalent of physically disconnecting and reconnecting the HDMI cable between the source device and the matrix page 65 Operating the 4x4 Se
53. ntrol Unit Bottom Battery Cover ID Name Description 1 Battery slot Holds the batteries for operating the shown without batteries IR remote Use only 1 5V AAA type batteries See Installing the Batteries for more information 2 DIP switch bank Use these DIP switches to set the IR channel of the remote See Setting the IR Channel for details page 6 Getting Started IR Remote Control Unit Installing the Batteries 1 Remove the battery cover on the bottom of the IR remote control unit 2 Make sure that the batteries are installed with the correct polarity as shown in the illustration below Always use two 1 5V AAA type batteries 3 Replace the battery cover Battery Cover WARNING Risk of explosion if battery is replaced by an incorrect type Dispose of used batteries according to the instructions page 7 Getting Started IR Remote Control Unit Setting the IR Channel In order to function correctly both the matrix and the IR remote control must be set to the same IR channel To set the IR channel of the matrix use the set ir command or use the IR Channel setting under the System page of the Web interface IR Channel DIP settings 0 ON default ma 1 2 1 ON 1 2 2 ON 2 3 ON r 1 1 2 amp S E gs EE s5 P p 5 ge DIP switches page 8 Installation Connecting the 4x4 Seamless Matrix for HDMI 1 Connect up to four H
54. only available if the network mode is set to static Gateway Enter the gateway router address in this field This option is only available if the network mode is set to static HTTP Enter the HTTP listening port in this field page 77 Operating the 4x4 Seamless Matrix for HDMI Web Interface Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Main VO Setup Manage EDID Network System Power STANDBY Help Log Out TCP Telnet Settings Enable TCP Access Require Password on Connect User Name Old Password New Password Confirm New Password Terminal Port Enable TCP Access Check this box to enable TCP access Require Password on Connect Check this box to prompt the user for a password at the start of a Telnet session User Name Enter the user name required for login in this field Old Password Type the current old password in this field New Password Type the new password in this field page 78 Operating the 4x4 Seamless Matrix for HDMI Web Interface Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Main VO Setup Manage EDID Network System UDP Settings Enable UDP Access i UDP Port 50007 Remote UDP IP Address 192 168 1 80 Remote UDP Port 50008 Enable UDP Access Place a check mark in this box to enable UDP access UDP Port Enter the UDP listening port in this field Enable UDP Echo Place a check mark in this box to enable UDP echo Destination UDP IP Address Enter the r
55. or HDMI Menu System Adjusting the Brightness 1 Press the Menu button on the front panel or on the IR remote control The menu system will be displayed jefen 7 2 Press the Select button to display the Setup Menu If using the IR remote press the OK button 3 Use the A or V buttons to highlight Picture Settings iefen 7 4 Press the Select button to display the Picture Settings menu If using the IR remote press the OK button 5 The Out Select option should be highlighted If not use the A or VW buttons to highlight it Each output can have individual brightness settings Therefore the output must be selected before making changes to it page 32 Operating the 4x4 Seamless Matrix for HDMI Menu System 6 Press the Select button to select the Out Select option The currently selected output will be highlighted in orange 7 Select the desired output using the lt or gt buttons ofend 8 Press the Select button to accept the current output selection 9 Usethe A or buttons to highlight the Brightness option 10 Press the Select button to select the Brightness option 11 Change the brightness value using the lt or gt buttons jefen J 12 Press the Select button to accept the change page 33 Operating the 4x4 Seamless Matrix for HDMI Menu System Adjusting the Saturation 1 Press the Menu button on the front panel or on the IR remote control The menu system will
56. ow HDCP content to pass on the input Use the Not Accept option to prevent HDCP content from being transmitted to the input Output Always On Follow Input Use the Always On option to allow HDCP to pass through on the output Use the Follow Input option to have the output follow the input setting Accept Not Accept 8 Press the Select button to accept the change If using the IR remote press the OK button page 43 Operating the 4x4 Seamless Matrix for HDMI Menu System EDID Management 1 Press the Menu button on the front panel or on the IR remote control The menu system will be displayed Press the Select button to display the Setup menu If using the IR remote press the OK button Use the A or Y buttons to highlight the EDID option 4 Press the Select button to display the EDID menu If using the IR remote press the OK button efeng YES page 44 Operating the 4x4 Seamless Matrix for HDMI Menu System 5 Press the Select button to select the Lock EDID option 6 Use the lt or gt buttons to change the value of the Lock EDID option 7 Press the Select button to accept the Lock EDID value Selecting an EDID 1 Make sure the Lock EDID option is set to No 2 Usethe A or Y buttons to highlight the desired output containing the EDID to be copied to the input The 1080p 2CH or 1080p Multi Ch EDID can also be selected When selecting an EDID make sure that all displays can support t
57. r executing this command Use the show_ipmode command to display the current IP mode Syntax set ipmode paraml Parameters param1 Value 0 1 Value Description 0 DHCP 1 Static Example set ipmode 1 IP MODE SET TO STATIC PLEASE REBOOT TO ACTIVATE page 112 Advanced Operation Commands set_ir The set ir command sets the IR channel for the matrix The default IR channel setting is 1 The IR channel for the switcher can also be set under the tab within the Web interface Both the matrix and the included IR remote control must be set to the same IR channel in order to work properly To set the IR channel for the included IR remote control see Setting the IR Channel Syntax set ir paraml Parameters param1 Channel 0 3 Value Description 0 IR channel 0 1 IR channel 1 2 IR channel 2 3 IR channel 3 Example set ir 1 IR CHANNEL IS SET TO 1 page 113 Advanced Operation Commands set_netmask The set_netmask command sets the subnet mask The subnet mask must be entered using dot decimal notation The matrix must be rebooted after executing this command The default subnet mask is 255 255 255 0 Use the show netmask or the show ipconfig command to display the current net mask of the matrix Syntax set netmask paraml Parameters param1 Subnet mask Example set netmask 255 255 255 0 NETMASK 255 259 255 0 page 114 Advanced Operation set_output Commands
58. rom 1 to 2 If param1 bank then param2 must specifiy an EDID bank from 1 to 8 If param7 output then param2 must specify an output from 1 to 4 continued on next page page 104 Advanced Operation Commands param3 Target Target Description input Specifies an input bank Specifies an EDID bank continued on next page param4 Target 1 8 Value Description I eee 4 Input b sas 8 EDID bank When specifying param4 the available arguments will depend upon the value of param3 If param3 input then param4 must be an input from 1 to 4 If param3 bank then param4 must specifiy an EDID bank from 1 to 8 Examples set edid int 2 input 4 INTERNAL EDID 2 IS SAVED TO INPUT4 set edid bank 3 bank 5 BANK EDID 3 IS SAVED TO BANK5 page 105 Advanced Operation Commands set_eth relink The set_eth relink command is used when an IP setting has changed This command is the equivalent of disconnecting and reconnecting the Ethernet cable on the matrix Syntax set eth relink Parameters None Example set eth relink GONNA RE LINK EXT HD SL 444 FW V2 34 IP 10 5 64 214 Netmask 255 255 255 0 Gateway 10 5 64 1 page 106 Advanced Operation Commands set_ gateway The set_ gateway command sets the gateway address The gateway must be typed using dot decimal notation The matrix must be rebooted after executing this command The default gateway is 192 168 1 1 Synt
59. s of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Batteries that may be included with this product and or accessories should never be exposed to open flame or excessive heat Always dispose of used batteries according to the instructions 4x4 Seamless Matrix for HDMI Warranty Information Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required
60. s the current HTTP listening port of the matrix Use the set_ http port command to set the HTTP listening port Use the set http port command to set the HTTP listening port Syntax show http port Parameters None Examples show http port HTTP PORT IS 80 show hue The show hue command displays the current hue setting for all outputs Use the set hue command to set the hue value Syntax show hue Parameters param1 Output Example show hue OUT A HUE VALUE 30 page 129 Advanced Operation Commands show input name The show_ input name command displays the name of the specified input Use the set input name command to assign a name to an input Syntax show input name Parameters param1 Input 1 4 Example show input name 3 THE NAME FOR INPUT2 IS Blu ray show ip The show_ip command displays the current IP address of the matrix Use the set ipadd command to set the IP address of the matrix Syntax show ip Parameters None Example show ip IP ADDRESS 10 5 64 214 page 130 Advanced Operation Commands show_ipconfig The show_ipconfig command displays the current TCP IP settings Syntax show ipconfig Parameters None Example show ipconfig IP CONFIGURATION IS DECP IP 10 5 64 214 NETMASK 255 255 255 0 GATEWAY 10 5 64 1 MAC ADDRESS 04 1c 91 03 b0 00 show_ipmode The show_ipmode command displays the curren
61. sesecccccidsecnedecnnendsannronscussananendimakdaneanngasneadedesaasdeanmnces 34 Adjust ng the HUE sctrduttacecveentacieciaianteacemtentstinauten bcicueinita noleniien NARSES rateutintenl 36 DRESE e EEA E EN E A A 38 PE E AE E EA E E T S A E A TE 42 EDID Managemen ess aaa aiaiai 44 Changing he PS Gta S caccctaccccncassxnsdatcacagssastacandatardabacseisensens i iiaa 46 Changing the Telnet Settings iccviniccsdecbresevicrectonnieevieoridenvinedeenenaaiied 49 Changing the UDP Settings ssiscscccesscoscttatiaaseastawadiatsatecdisiastntetialsaeneectesnts 51 SUSI SOS e E EE E I E O 53 viii 4x4 Seamless Matrix for HDMI 03 04 Table of Contents Web Interface so csi ci ceiencantersernciexnerntaeateedeasandinnedebenade lt backbawaaneddadadoadevaaRlouslxbensdenswatiedd 54 Using the built in Web Interface cccccceceeccesssseeeeeseeeeseeeeessaeeeeeeeessanes 54 Main TONG asetperass cnnascvencnidscentaieenendaisaiveudem anurans decaxeansienmercaes sesancestionens 55 Mam P VO Statusne een aE EUO E DTi EEEE E Ea 59 Main gt Display IIO ssesisssssnninonsnninsikopneninnon n AAE AREPAN ARa 61 VO Setup gt Preset NAMeS xs oni2sicccictsnesetiaatseresntecnantedeandseatecnaneacteGiacdendueeeesns 63 VO Setup F VO Names iior A EATE iE ariii 64 VO Setup gt HPD COMO i ccsccncnasencensddscstaneaccsacsenadiecedacansasenaessddecstetinnstesedes 65 O Seun P ai 21S seine ee em te a Eira ira 66 VO Setup P VideO Semen teenth nten ee teet steht her he en
62. set the remote UDP port Syntax show udp remote port Parameters None Example show udp remote port REMOTE UDP COMMUNICATION PORT IS 508 show ver data The show_ver data command displays the current software and hardware version Syntax show ver data Parameters None Example show ver data VERSION SW V2 34 HW V2 2 page 140 Advanced Operation Commands unmask The unmask command unmasks the specified output s Use the mask command to mask the specified output s If param1 0 then all outputs are unmasked Syntax unmask parami Parameters param1 Output 0 4 Example unmask 2 OUTPUT 2 IS UNMASKED page 141 Advanced Operation Commands use discovery The use tcp access command enables or disables discovery access mode If this mode is disabled then the 4x4 Seamless Matrix for HDMI will not be discoverable when using the Gefen Syner G Software Suite The default setting is enabled Syntax use discovery parami Parameters param1 Value 0 1 Value Description 0 Discovery access disabled 1 Discovery access enabled Example use discovery 0 DISCOVERY PROTOCOL IS DISABLED page 142 Advanced Operation Commands use tcp access The use tcp access command enables or disables Telnet access Syntax tuse tcp access paraml Parameters param1 Value 0 1 Value Description 0 Disable Telnet access I Enable Telnet access Example use tcp
63. set_webui ad pass The set webui ad pass command sets the Administrator password for the Web GUI The password is case sensitive and cannot exceed 8 characters in length The default password is Admin Syntax set webui ad pass parami Parameters param1 Password Example set webui ad pass bossman WEB UI ADMINISTRATOR PASSWORD IS SET bossman set_webui op pass The set webui ad pass command sets the Operator password for the Web GUI The default password is Admin Syntax set webui op pass parami Parameters param 1 Password Example set webui op pass minion WEB UI OPERATOR PASSWORD IS SET minion page 124 Advanced Operation Commands show bank name The Show bank name command displays the name for the specified EDID bank To name an EDID bank use the set_ bank name command Syntax show bank name parami Parameters param1 Bank 1 8 Example show bank name 5 THE NAME FOR BANK5 IS Dell24 show_brightness The show brightness command displays the brightness level for all outputs Use the set brightness command to set the brightness value Syntax show brightness Parameters None Example show brightness OUT A BRIGHTNESS VALUE 65 page 125 Advanced Operation Commands show_contrast The show_contrast command displays the contrast level for all outputs Use the set contrast command to set the contrast value Syntax show contrast Parame
64. t Displays the saturation value for all outputs Displays the TCP access status Displays the current Telnet port Displays the UDP access status Displays the current UDP port Displays the current UDP remote IP address Displays the current UDP remote port Displays the current hardware and software version Disables masking on the specified output page 89 Advanced Operation Commands ruse discovery Enables or disables discovery mode use tcp access Enable disable Telnet access use telnet pass Enable disable login credentials for Telnet sessions use udp access Enable disable UDP access m Displays the matrix routing status i Routes the specified input to the output S Routes the specified input to all outputs display telnet welcome The display telnet welcome command enables disables the Telnet welcome message during a Telnet session Syntax display telnet welcome parami Parameters param1 Value 0 1 Disable welcome message Enable welcome message Example display telnet welcome 1 TELNET WELCOME SCREEN IS ENABLED When enabled and a Telnet session has been started the following will appear Welcome to EXT HD SL 444 TELNET page 90 Advanced Operation Commands fadefault The adefault command resets the matrix to factory default settings Outputs are unmasked and all IP and UDP settings are reset to default settings Syntax fadefault Parameters None Example fadefault
65. t IP mode Use the set ipmode command to set the IP mode Syntax show ipmode Parameters None Example show ipmode IP MODE SET TO DHCP page 131 Advanced Operation Commands show ir The show ir command displays the IR channel of the matrix Use the set ir command to set the IR channel of the matrix Syntax show ir Parameters None Example show ir IR CHANNEL IS SET TO 0 show mac addr The show mac addr command displays the MAC address of the matrix Syntax show mac addr Parameters None Example show mac addr MAC ADDRESS IS 04 1c 91 03 b 0 00 page 132 Advanced Operation Commands show me The show_me command enables or disables the flashing of the LED on the device When enabled the LED indicator will flash red and blue The default setting is disabled Syntax show me parami Parameters param1 Value 0 1 Value Description 0 Disabled 1 Enabled Examples show me 1 SHOWME IS ON page 133 Advanced Operation Commands show_netmask The show_netmask command displays the current net mask of the 4x4 Seamless Matrix for HDMI Use the set netmask command to set the net mask Syntax show netmask Parameters None Example show netmask NETMASK 255 255 255 0 show_output The show output command displays the current output resolution Use the set output command to set the output resolution Syntax show output P
66. t welcome message Resets the current routing and masking state to factory default settings Displays the list of available commands Cycles with HPD line on the specified output Locks the local EDID when the matrix is power cycled Locks unlocks the matrix Masks the specified outputs Enables disables muting on all outputs Toggles the power on the matrix Reboots the matrix Loads the specified routing preset into memory Resets picture settings to factory default Saves a routing preset to memory Assigns a name to the specified EDID bank Sets the brightness level for all outputs Sets the contrast level for all outputs Sets the device description Assigns the specified EDID to an input or bank Performs a re link operation on the Ethernet port Sets the gateway address Enables disables HDCP detection Sets the HTTP listening port Sets the hue for all outputs Assigns a name to the specified input Sets the IP address Sets the IP mode DHCP or static Sets the IR channel of the matrix Sets the subnet mask Sets the output resolution Assigns a name to the specified output Assigns a name to the specified preset Set the saturation for the specified output Sets the Telnet password Sets the Telnet listening port Sets the Telnet username page 88 set udp port set udp remote ip set udp remote port set webui ad pass set webui op pass Show bank name show brightness show contrast show device descr show disco
67. ted nce ee ta bicantetne tens 9 Network Configuration using SYNer G ccccccccseeeeeeeeeeaeeeeeeeeeeaaeeeeeeeeeaaes 10 Operating the 4x4 Seamless Matrix for HDMI MOUCHO esaa E E E 14 Standby MOGG caseron ete a asa aiiin 14 Turning on the 4x4 Seamless Matrix for HDMI ccccceceeseeeeeeeeeaeeeeeees 14 EE TERE E E TATE T E A E EAE 15 Determining the Current Routing State cccccccccceeessesseeeeeseeeeseeeeessanes 15 Routing Inputs to Outputs ocecc 5cg2e2icacrscessanchesaadeacunsedeseuslascedading coduesaznecemedaass 16 Masking Unmasking Outouts cccocsscecascctccssesenssacsanieeiasseaatasseestaieedernadieaceues 18 Saving FROULING PRESETS wicceis wcodeceanctdetcisanansdestiusdnoiaetancnnaddedsetaciaatieaeesecshereiests 20 Loading Routing PIGSEtS sacs ccsrscasccecuecctaciactccreantensamaqueciasceateiuscbadatebenadinecins 21 L ckmg Unlocking the Wat cessere aE E raii 22 Using the IR EXtender sssasisioucnisctmsinregnisnasieincdinrdeaiientaeissinandiatanvennahiieansaniatdaceniainsan 24 Menu 5 S FIG eere enen EE E E E E ENA A O EENES 25 Accessing the Menu SyStem c ccccccsscssseeeeeceeesseeeeseaeeesseeeesseageeeeeeseas 25 Setting the Output Resolution s scehds ccccchoniacaiaetoctoul nnewnsenteasenieartasondoreeterdaxt 28 Adjusting the CON ASE occ oie nncac 2tachnnaisdastennnas sleavedneasdesleaasanesd eUnaestunidruadendancens 30 Adjusting ine MOS Sa eresien iere E o E a E EEE 32 Adjusting the Saturation
68. ters None Example show_contrast OUT A CONTRAST VALUE 74 show device descr The show device descr command displays the device description Use the set device descr command to assign the device description Syntax show device descr Parameters None Example show device descr DEVICE DESCRIPTION NAME IS SET TO Matrix 1 page 126 Advanced Operation Commands show_discovery The show_discovery command displays the Discovery Service status Use the use discovery command to enable or disable the Discovery service Syntax show discovery Parameters None Example show discovery DISCOVERY PROTOCOL IS ENABLED show_gateway The show_gateway command displays the current gateway address of the matrix Use the set_ gateway command to set the gateway address Syntax show gateway Parameters None Example show gateway GATEWAY 192 168 1 11 page 127 Advanced Operation Commands show_hdcp The show_hdcp command displays the current HDCP setting for inputs or outputs Use the set_hdcp command to set the HDCP input and output states Syntax show hdcp parami Parameters param1 Value 0 1 Value Description 0 Query input signal 1 Query output signal Examples show hdcp 0 HDCP INPUT IS SET TO ACCEPT show hdcp 1 HDCP OUTPUT IS SET TO FOLLOW INPUT page 128 Advanced Operation Commands show http port The show http port command display
69. tton 4 Use the A or V buttons to highlight the Telnet Settings option ofend 5 Press the Select button again to display the Telnet Settings menu If using the IR remote press the OK button ENABLE DISABLE 23 page 49 Operating the 4x4 Seamless Matrix for HDMI Menu System 5 Use the A or V buttons to highlight the option to change The Telnet Access option will be highlighted automatically 6 Once the desired option is highlighted press the Select button to select it If using the IR remote control press the OK button When an option is selected its current value will be highlighted in orange ENABLE DISABLE 7 Use the lt or gt buttons to change the current value 8 Press the Select button to accept the current changes If using the IR remote control press the OK button Telnet Access Enables On or disables Off Telnet access for the HD Video Wall Controller Require Password Enables or disables the password prompt at the beginning of a Telnet session Terminal Port Sets the Telnet listening port for the 4x4 Seamless Matrix for HDMI page 50 Operating the 4x4 Seamless Matrix for HDMI Menu System Changing the UDP Settings 1 Press the Menu button on the front panel or on the IR remote control The menu system will be displayed 2 Usethe A or Y buttons to highlight the Network option efeng 3 Press the Select button to display the Network menu If using the
70. tton to select the EDID file to be uploaded Select Bank Location Click this drop down list to select the bank to where the EDID will be uploaded Options Bank 1 Bank 8 Upload Click this button to upload the EDID to the specified bank page 75 Operating the 4x4 Seamless Matrix for HDMI Web Interface Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Power STANDBY 2 Heip Log Out Download EDID select EDID File to Download Bank 1 Download Select EDID File to Download Click this box to select the EDID that is to be saved to a file The EDID file will be saved in binary bin format Options Bank 1 Bank 8 1 Output 1 4 Output 4 1 Input 1 4 Input 4 Download Click this button to download the selected EDID to a file page 76 Operating the 4x4 Seamless Matrix for HDMI Web Interface Network Gefen 4x4 Seamless Matrix for HDMI EXT HD SL 444 Main VO Setup Manage EDID Network System Power STANDBY 7 Heip Log Qut IP Settings MAC Address 04 1 91 03 b0 00 Mode DHCP P Address Subnet Gate TTT Lh Ui Wi c 7 HTTP Port MAC Address The MAC address of the matrix The MAC address cannot be changed Mode The network mode setting Options Static DHCP IP Address Enter the IP address of the matrix in this field This option is only available if the network mode is set to static Subnet Enter the subnet mask of the matrix in this field This option is
71. u System The matrix uses a built in menu system to manage and control all video features To access the menu system press the Menu button on the front panel or on the included IR remote control gt 1 i 9 9 9 9 Vief OO 6 E Y a ao After pressing the Menu button on the front panel the Menu button will remain illuminated as long as the menu system is displayed on the screen By default the menu system will be displayed in the top left corner of the display The Menu button will not be illuminated when activated from the IR remote control an o The time out value duration for the menu system can be changed from within the menu system See OSD Settings for details on changing this value 10 00 00 0 Diecee 0 0 8020 aie page 25 Operating the 4x4 Seamless Matrix for HDMI Menu System Using the Front Panel Controls Use the lt gt A and Y buttons on the front panel to move around within the menu system Press the A and VW buttons to move up and down Press the lt or gt buttons to change the value of the current selection Press the Select button to make the desired selection The current selection will be highlighted in green ints ee ihe Press the A and V buttons to O EEDE make a selection within the menu system EHE H E see n Press the lt and gt buttons to change the value of a setting within the menu system page 26 Operating the 4x4
72. vertighten the locking connector on the power receptacle page 3 Getting Started IR Remote Control Unit Top 3 h o ee lask 9 10 11 Name Description Info Used to toggle notifications on all outputs In 1 4 Use these buttons to select the desired input See Routing Basics for more information on routing inputs to outputs page 4 Getting Started 10 11 Name Mask Menu lt gt A V OK Exit Presets Power Out 1 4 Lock Mute IR Remote Control Unit Description Press this button to mask or unmask the selected output See Masking Unmasking Outputs for more information Press this button to display the built in menu system Used to access and change features within the menu system Use the arrow buttons to move around within the menu system or change a value Press the OK button to make a selection within the menu system Press this button to exit the main menu or exit from sub menus Use these button to select the desired routing preset The buttons below 7 and 9 are not used See Saving Routing Presets for more information on working with routing presets Press this button to power ON or power OFF the matrix Use these buttons to select the desired input See Routing Basics for more information on routing inputs to outputs Press this button to lock unlock the matrix Mutes the audio on all outputs page 5 Getting Started IR Remote Co
73. very show gateway show hdcp show http port show hue show input name show ip show ipconfig show ipmode set ir show mac addr show me show netmask show_ output show output name show power show preset name show saturation show tcp access show telnet port show udp access show udp port show udp remote ip show_ udp remote port show ver data unmask Advanced Operation Commands Sets the UDP serial port Sets the remote UDP IP address Sets the remote UDP port Sets the Administrator password Sets the Operator password Displays the name for the specified EDID bank Displays the brightness value for all outputs Displays the contrast value for all outputs Displays the device description Displays the Discovery feature status Displays the IP address of the router gateway Displays the HDCP status of the specified input Displays the Web server listening port Displays the hue value for all outputs Displays the specified input name Displays the current IP address of the matrix Displays the current TCP IP settings of the matrix Displays the current IP mode DHCP or static Displays the IR channel of the matrix Displays the MAC address of the matrix Enables or disables the flashing of the LED on the device Displays the current subnet mask Displays the output resolution Displays the specified output name Displays the power state of the matrix Displays the name for the specified prese
74. x press and hold the Lock button The Lock button will begin to flash 5 Continue holding down the Lock button until it stops flashing 6 The matrix is now unlocked and can be used normally Matrix is unlocked Once the matrix is unlocked the Lock button will no longer be illuminated page 22 Operating the 4x4 Seamless Matrix for HDMI 1 2 3 4 Locking Unlocking the Matrix Using the IR Remote Control Press the Lock button on the IR remote control m e button The Lock button on the front panel of the matrix will remain illuminated as long as the matrix is locked To unlock the matrix press the Lock button The Lock button will turn off The matrix is now unlocked and can be used normally Once the matrix is unlocked the Lock button will no longer be illuminated page 23 Using the IR Extender There may be situations where the IR sensor is blocked by a cabinet or other mounting device In this case the included IR extender Gefen part no EXT RMT EXTIRN can be connected to the IR Ext port on the matrix The sensor on the IR extender behaves exactly like the sensor on the front panel of the matrix Always point the IR remote control unit in the direction of the IR sensor IR extender cee ff ji e 8 Go oo eeeoai depbe t 0 4 ie eA i IR remote IR sensor page 24 Operating the 4x4 Seamless Matrix for HDMI Menu System Accessing the Men
75. x4 Seamless Matrix for HDMI See RS 232 and IP Configuration for more information on configuring RS 232 page 29 Operating the 4x4 Seamless Matrix for HDMI Menu System Adjusting the Contrast 1 Press the Menu button on the front panel or on the IR remote control The menu system will be displayed jefen J 2 Press the Select button to display the Setup Menu If using the IR remote press the OK button 3 Use the A or V buttons to highlight Picture Settings iefen 7 4 Press the Select button to display the Picture Settings menu If using the IR remote press the OK button 5 The Out Select option should be highlighted If not use the A or VW buttons to highlight it Each output can have individual contrast settings Therefore the output must be selected before making changes to it page 30 Operating the 4x4 Seamless Matrix for HDMI Menu System 6 Press the Select button to select the Out Select option The currently selected output will be highlighted in orange 7 Select the desired output using the lt or gt buttons ofend 8 Press the Select button to accept the current output selection 9 Usethe A or V buttons to highlight the Contrast option 10 Press the Select button to select the Contrast option 11 Change the contrast value using the lt or gt buttons jefen J 12 Press the Select button to accept the change page 31 Operating the 4x4 Seamless Matrix f

Manual - Gefen

Contents

Download Pdf Manuals

Related Search

Related Contents