User manual
Contents
1. lt Back gt T 5 em VGA D sub Signal Cable Power Cable Not Included Accessory a DVI D Cable Accessory Computer VGA D Sub cable is not supplied with the monitor you need to use a special VGA D Sub cable dedicated for this model Please contact the iiyama Support Centre in your country if you wish to connect the monitor via the VGA input BEFORE YOU OPERATE THE MONITOR 11 ENGLISH COMPUTER SETTING Signal Timing Change to the desired signal timing listed on page 29 COMPLIANT TIMING ADJUSTING THE VIEWING ANGLE ProLite E2482HD W For optimal viewing it is recommended to look at the full face of the monitor W Hold the stand so that the monitor does not topple when you change the monitor s angle m You able to adjust the monitor s angle up to 22 upward 5 downward W n order to ensure a healthy and relaxed body position when using the monitor at visual display workstations it is recommended that the adjusted tilt angle should not exceed 10 degrees Adjust the monitor s angle to your own preference W Do not touch the LCD screen when you change the angle It may cause damage or break the LCD Screen W Careful attention is required not to catch your fingers or hands when you change the angle 12 BEFORE YOU OPERATE THE MONITOR ADJUSTING THE HEIGHT AND THE VIEWING ANGLE2. 1 Luminance adjustment is disabled when Adv Contrast mode is activated Luminance adjustment is disabled when i Style Color is activated Adjust the Brightness when you are using the monitor a dark room and feel the screen is too bright OPERATING THE MONITOR 15 ENGLISH ENGLISH Geometry Only Analog Input Adjustment Item Problem Option Button to Press CE ua Too left 4 Position right eg lt ui Too low e gt Position E Too high f lt Too narrow e gt Pixel Clock Too wide amp 4 Phase To correct flickering text or lines 4 Color Adjustment Item Problem Option Button to Press 9300K Bluish white 7500K Yellowish white 6500K Reddish white Red Usep Too weak gt ser Prese reen Blue Too strong amp 4 Color adjustments is disabled when i Style Color or Blue Light Reducer is activated Adjustment Problem Option Button to Press e H Position Ose foo lot OSD is too right 4 OSD is too low gt V Position OSD is too high lt Ep OSD Time You can set the OSD display duration time gt between 5 and 30 seconds 4 16 OPERATING THE MONITOR WD Language Recall All
3. 533 5mm 21 0 301 0mm 11 9 340 0mm 13 4 uu 56 5mm 2 2 393 0mm 15 5 386 5mm 15 2 516 5mm 20 3 Maximum adjustment range DIMENSIONS ProLite E2482HD 565 5mm 22 3 533 5mm 21 0 238 0 9 4 340 0mm 13 4 301 0mm 11 9 COMPLIANT TIMING 56 5mm 2 2 412 0mm 16 2 230 0mm 9 1 250 0mm 9 8 203 0mm 8 0 VGA 640x480 31 469kHz 59 940Hz 25 175MHz SVGA 800x600 37 879kHz 60 317Hz 40 000MHz XGA 1024x768 48 363kHz 60 004Hz 65 000MHz VESA SXGA 1280x1024 63 981kHz 60 020Hz 108 000MHz WXGA 1440x900 55 935kHz 59 887Hz 106 500MHz UXGA 1600x1200 75 000kHz 60 000Hz 162 000MHz WSXGA 1680x1050 65 290kHz 60 000Hz 146 250MHz Full HD 1920x1080 66 590kHz 59 930Hz 138 500MHz 640x350 31 469kHz 70 087Hz 25 175MHz z VOGA TEXT 720x400 31 469kHz 70 087Hz 28 322MHz DVI input is not compliant APPENDIX 29 M144A21 ENGLISH
4. 6 BEFORE YOU OPERATE THE MONITOR FITTING AND REMOVAL OF BASE ProLite E2482HD e VW MM Put the monitor on a stable surface The monitor may cause injury or damage if it falls or is dropped W Do not give a strong impact to the monitor It may cause damage Unplug the monitor before removal or installation to avoid electric shock or damage Installation D Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched Lay the monitor flat on a table with front face down Hold the monitor and push the Stand until it clicks and is secure Hold the monitor and push the Stand Base until it clicks and is secure Removal Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched Lay the monitor flat on a table with front face down Press and hold the hooks inside pull the Stand Base Press the stopper at the top of the stand and pull it to remove the stand from the monitor Stopper ENGLISH Stand t lt m Stand Base Hook BEFORE YOU OPERATE THE MONITOR 7 ENGLISH CONTROLS AND CONNECTORS ProLite B2482HD Geoseso Front Power Indicator Xel Blue Norm
5. Blue Light Reducer Digital Character Smoothing Automatic Set up Plug amp Play VESA DDC2B Compliant Windows Vista 7 8 Compliant Power Management ENERGY STAR VESA DPMS Compliant VESA Mounting Standard 100mmx100mm Compliant Keyhole for Security Lock 9999 9 CHECKING THE CONTENTS OF THE PACKAGE The following accessories are included in your package Check to see if they are enclosed with the monitor If anything is missing or damaged please contact your local iiyama dealer or regional iiyama office Power Cable m DVI D Cable W Stand Base E Stand m Screw for stand fixing 3 W Safety Guide W Quick Start Guide The rating of the Power Cable enclosed 120V area is 10A 125V If you are using a power supply higher than this rating then a power cable with a rating of 10A 250V must be used However all guarantees and warranties are void for any problems or damage caused by a power cable not supplied by iiyama Accessory for ProLite E2482HD Accessory for ProLite B2482HD 4 BEFORE YOU OPERATE THE MONITOR WALL MOUNTING WARNING W When you use with the wall mounting in consideration of thickness of the mounting stage tighten the M4 Screw with washer which L length is 7mm to fasten the monitor Using the screw longer than this may cause electric shock or damage because it may contact with the electrical parts inside the monitor W Please check if the wall or ceiling can supp
6. ProLite E2482HD 12 ADJUSTING THE HEIGHT AND THE VIEWING ANGLE Prokite B2482HD citer tette nete enne tenentes 13 PANEL ROTATION ProLite 2482 13 OPERATING THE MONITOR c tt tene ttr nter 14 ADJUSTMENT MENU CONTENTS eee eee 15 SCREEN ADJUSTMENIIS itte ie ettet 21 POWER MANAGEMENT 24 TROUBLE SHOOTING terree tient ta e rrt cin eto 25 RECYCLING INFORMATIQON nitent 26 APPENDIX S a 27 SPECIFICATIONS ProLite 2482 27 SPECIFICATIONS ProLite 2482 28 DIMENSIONS ProLite 2482 29 DIMENSIONS ProLite 2482 29 COMPLIANT TIMING 29 FOR YOUR SAFETY SAFETY PRECAUTIONS WARNING STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE If you notice any abnormal phenomena such as smoke strange sounds or fumes unplug the monitor and contact your dealer or iiyama service center immediately Further use may be dangerous and can cause fire or electric shock NEVER REMOVE THE CABINET High voltage circuits are inside the monitor Removing the cabinet may expose you to the danger of fire or electric shock DO NOT
7. ProLite B2482HD W For optimal viewing it is recommended to position yourself directly opposite to the full face of the monitor then adjust the monitor s height and angle to your own preference Hold the panel so that the monitor does not topple when you change the monitor s height or angle You are able to adjust the monitor s height to 130mm angle up to 45 degrees right and left 22 degrees upward and 5 degrees downward 130mm W Do not touch the LCD screen when you change the height or the angle It may cause damage or break the LCD Screen W Careful attention is required not to catch your fingers or hands when you change the height or the angle W Injury can occur if care is not taken to avoid finger contact with the displays base when adjusting the height Monitor PANEL ROTATION ProLite B2482HD CD Adjust the mother s height Q Rotate the panel 90 degrees Portrait Turn clockwise Landscape Turn counter clockwise W Attempting to rotate without fully extending upward may cause damage to stand W Video card for portrait display will be required for rotating the image on the Screen 3 Adjust the monitor s angle to your preference BEFORE YOU OPERATE THE MONITOR 13 ENGLISH ENGLISH OPERATING THE MONITOR To create the best picture your iiyama LCD monitor has been preset at the
8. Yes Factory preset data is restored English English Nederlands Dutch Francais French Japanese Language Deutsch German Simplified Chinese Italiano Italian Russian Polski Polish Cesky Czech Espa ol Spanish Recall No Return to Menu OPERATING THE MONITOR 17 ENGLISH ENGLISH Miscellaneous Adjustment Item Problem Option Button to Press A Sharpness amp gt 4 You can change the picture quality from 1 to 5 sharp to soft Press the gt Button to change the picture quality in numerical order Press the Button to change the picture quality in reverse numerical order 12345 DDC CI gt On Off On DDC CI is turned ON DDC CI is turned OFF DDC CI On and Off are switched as follows by pressing the Button successively Display Information Displays information regarding the current input signal coming from the graphic card in your computer Miscellaneous Display Information 1920x1080 60 Hz 19443 See your graphic card user guide for more information about changing the resolution and refresh PCM Display Mode On Increased Contrast Ratio Adv Contrast Off Typical Contrast Ratio Full Expansion display Aspect Expansion display of Aspect Opening Logo On iiyama Logo displayed when the monitor is turned on Logo does not
9. Before reporting the screen defect please Important prepare the following information evidence Note model number If there is no fault found in the collected equipment after inspection the transferring party shall incur charges for transport and administration purchase receipt and serial number name and address for collection telephone fax number for availability during the day If you have checked all of the above and there is convenient collection date date time still no picture call our information line for assistance short description of the defect in your country see the identification plate on the back of the case www iiyama com il MARKING DECLARATION OF CONFORMITY This LCD monitor complies with the requirements of the EC EU Directive 2004 108 EC EMC Directive 2006 95 EC Low Voltage Directive 2009 125 EC ErP Directive and 2011 65 EU ROHS Directive The electro magnetic susceptibility has been chosen at a level that gives correct operation in residential areas business and light industrial premises and small scale enterprises inside as well as outside of the buildings All places of operation are characterised by their connection to the public low voltage power supply system IIYAMA CORPORATION Wijkermeerstraat 8 2131 HA Hoofddorp The Netherlands We recommend recycling of used product Please contact your dealer or iiya
10. PUT ANY OBJECT INTO THE MONITOR Do not put any solid objects or liquids such as water into the monitor In case of an accident unplug your monitor immediately and contact your dealer or iiyama service center Using the monitor with any object inside may cause fire electric shock or damage INSTALL THE MONITOR ON A FLAT STABLE SURFACE The monitor may cause an injury if it falls or is dropped DO NOT USE THE MONITOR NEAR WATER Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric shock OPERATE UNDER THE SPECIFIED POWER SUPPLY Be sure to operate the monitor only with the specified power supply Use of an incorrect voltage will cause malfunction and may cause fire or electric shock PROTECT THE CABLES Do not pull or bend the power cable and signal cable Do not place the monitor or any other heavy objects on the cables If damaged the cables may cause fire or electric shock ADVERSE WEATHER CONDITIONS It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in power may cause malfunction It is also advised not to touch the plug in these circumstances as it may cause electric shock FOR YOUR SAFETY 1 ENGLISH ENGLISH CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur or in humid dusty or smoky areas as it may cause fire electric shock or damage You should also avoid areas where the sun
11. Pulling or inserting the plug with wet hands may cause electric shock WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER Be sure the computer is strong enough to hold the weight of the monitor otherwise you may damage your computer REMARK FOR 24 7 USAGE This product is not specifically designed for 24 7 usage in all environments OTHERS ERGONOMIC RECOMMENDATIONS To eliminate eye fatigue do not operate the monitor against a bright background or in a dark room For optimal viewing comfort the monitor should be just below eye level and 40 60 cm 16 24 inches away from your eyes When using the monitor over a prolonged time a ten minute break every hour is recommended as looking at the screen continuously can cause eye strain 2 FOR YOUR SAFETY SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitors and do not indicate a problem Xel m When you first turn on the LCD monitor the picture may not fit in the display area because of the type of computer that is used In this case adjust the picture position to the correct position W You may find slightly uneven brightness on the screen depending on the desktop pattern you use W Due to the nature of the LCD screen an afterimage of the previous screen may remain after switching the image when the same image is displayed for hours In this case the Screen can be recovered slowly by changing the image or turning off the Power Switch for some hours CUSTOME
12. display when the monitor is of turned on Adv Contrast adjustments are disabled when i Style Color is activated 18 OPERATING THE MONITOR Input Select Adjustment Item Problem Option Button to Press AUTO D sub Select the Analog input Input Select Direct DVI Select the Digital DVI input Manual D sub Select the Analog input DVI Select the Digital DVI input It will be selected automatically when the selected signal is not available Input source is fixed not selected automatically when D sub and DVI which selected You can skip the Menu items and display an adjustment scale directly by using the following button operations Input Select Pressing and holding of the AUTO Button for 2 3 seconds when the Menu is not displayed OPERATING THE MONITOR 19 ENGLISH ENGLISH You can skip the Menu items and display an adjustment scale directly by using the following button operations ECO Mode Press the Button when the Menu is not displayed Brightness of back light is reduced Off Normal i Style Color Press the EXIT Button when the Menu is not displayed Off Return to a state set by color adjustment Standard For general windows environment and monitor default setting Game For PC game environment Cinema For movie and video environment Scenery For displaying outdoor scenery images T
13. in your country if you wish to connect the monitor via the VGA input Collect Cables Put the cables through the cable hole Collect cables at the back of the stand 10 BEFORE YOU OPERATE THE MONITOR CONNECTING YOUR MONITOR ProLite E2482HD Ensure that both the computer and the monitor are switched off Connect the computer to the monitor with the signal cable 3 Connect the monitor to the audio equipment with the Audio Cable for computer when using the audio features Connect the Power Cable to the monitor first and then to the power supply 5 Turn on your monitor and computer W The signal cables used for connecting the computer and monitor may vary with the type of computer used An incorrect connection may cause serious damage to both the monitor and the computer The cable supplied with the monitor is for a standard connector If a special cable is required please contact your local iiyama dealer or regional iiyama office W For connection to Macintosh computers contact your local dealer or regional iiyama office for a suitable adaptor m Make sure you tighten the finger screws at each end of the signal cable W The Class pluggable equipment Type A must be connected to protective earth W The socket outlet shall be installed near the equipment and shall be easily accessible ENGLISH Example of Connection
14. obtained via the IIYAMA web site http www iiyama com Adjust the image by following the procedure below to get the desired picture This manual explains adjustment under Windows OS CD Display the picture at the optimum resolution Enter the Test bmp screen adjustment pattern to wallpaper Xey m Consult the appropriate documentation for doing this W Test bmp is made at resolution of 1280 x 1024 Set the display position to center in the wallpaper setting dialogue box Adjustment pattern OPERATING THE MONITOR 21 ENGLISH ENGLISH Press the AUTO Button Auto Adjust Adjust the image manually by following procedure below when the screen has a flicker or blur or the picture does not fit in the display area after performing the Auto Adjust 5 Adjust the V Position so that the top and bottom of the picture frame will fit to the display area 1 Adjust the H Position so that the left side of the picture frame will move to the left edge of the display area 2 Stretch the right side of the picture frame to the right edge of the display area by adjusting the Pixel Clock W When the left side of the picture frame moves apart from the left edge of the display area during the Pixel Clock adjustment adjust steps 1 and 2 W Another way to make the Pixel Clock adjustment is to correct the vertical wavy lines in th
15. shines directly on the monitor DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located Please also ensure that you do not place any heavy objects on the monitor and that all cables are routed such that children may not pull the cables and possibly cause injury MAINTAIN GOOD VENTILATION Ventilation slots are provided to keep the monitor from overheating Covering the slots may cause fire To allow adequate air circulation place the monitor at least 10 cm or 4 inches from any walls Do not remove the tilt stand when operating the monitor Ventilation slots on the back of the cabinet will be blocked and the monitor may overheat if the stand is removed This may cause fire or damage Operating the monitor on its back side upside down or on a carpet or any other soft material may also cause damage DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR When you move the monitor turn off the power switch unplug the monitor and be sure the signal cable is disconnected If you do not disconnect them it may cause fire or electric shock UNPLUG THE MONITOR If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid accidents HOLD THE PLUG WHEN DISCONNECTING To disconnect the power cable or signal cable always pull it by the plug Never pull on the cable itself as this may cause fire or electric shock DO NOT TOUCH THE PLUG WITH WET HANDS
16. R SERVICE m If you have to return your unit for service and the original packaging has been discarded please contact your dealer or iiyama service center for advice or replacement packaging CLEANING B If you drop any materials or liquids such as water into the monitor when cleaning unplug the power cable immediately and contact your dealer or iiyama service center 6711011108 m For safety reasons turn off the power switch and unplug the monitor before you clean it NOTE W To protect the LCD panel do not scratch or rub the screen with a hard object B Never use any of the following strong solvents These will damage the cabinet and the LCD screen Thinner Spray type cleaner Benzine Wax Abrasive cleaner Acid or Alkaline solvent W Touching the cabinet with any product made from rubber or plastic for a long time may cause degeneration or loss of paint on the cabinet CABINET Stains can be removed with a cloth lightly moistened with a mild detergent solvent Then wipe the cabinet with a soft dry cloth LCD Periodic cleaning with a soft dry cloth is recommended SCREEN Don t use tissue paper etc because these will damage the LCD screen FOR YOUR SAFETY 3 ENGLISH ENGLISH BEFORE YOU OPERATE THE MONITOR FEATURES Supports Resolutions up to 1920 x 1080 9 High Contrast 1000 1 Typical Adv Contrast Function Available Brightness 250cd m Typical Quick Response Time 5ms Typical
17. al operation Orange Power Management Power Switch b Menu Select Button MENU Scroll Up Button gt 8 Scroll Down Mode Button 4 2 Exit Button EXIT Auto Button AUTO VGA D sub mini 15pin Connector D SUB 9 DVI D 24pin Connector DVI D AC Connector Alternating current Keyhole for Security Lock You can fasten a security lock and cable to prevent the monitor from being removed without your permission 2 Cable Holes 8 BEFORE YOU OPERATE THE MONITOR Back CONTROLS AND CONNECTORS ProLite E2482HD OQOOLEHO lt Front gt Power Indicator Xei Blue Normal operation Orange Power Management Power Switch b Menu Select Button MENU Scroll Up Button gt 8 Scroll Down ECO Mode Button 4 2 Exit Button EXIT Auto Button AUTO VGA D sub mini 15pin Connector D SUB 9 DVI D 24pin Connector DVI D AC Connector Alternating current Keyhole for Security Lock 9000 ENGLISH lt Back gt Nozi You can fasten a security lock and cable to prevent the monitor from being removed without your permission BEFORE YOU OPERATE THE MONITOR 9 ENGLISH CONNECTING YOUR MONITOR ProLite B2482HD CD Ensure that both the computer and the monitor are switched off Connect the compute
18. cker or blur for the particular computer in use The monitor is designed to provide the best performance at resolution of 1920 x 1080 but can not provide the best at resolutions of less than 1920 x 1080 because the picture is automatically stretched to fit the full screen It is recommended to operate at resolution of 1920 x 1080 in normal use Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to the screen enlargement process E t is preferable to adjust the image position and frequency with the monitor controls rather than the computer software or utilities W Perform adjustments after a warm up period of at least thirty minutes W Additional adjustments may be required after the Auto Adjust depending on the resolution or signal timing The Auto Adjust may not work correctly when displaying the picture other than the screen adjustment pattern In this case manual adjustments are required There are two ways to adjust the screen One way is automatic adjustment for Position Pixel Clock and Phase The other way is performing each adjustment manually Perform the Auto Adjust first when the monitor is connected to a new computer or resolution is changed If the screen has a flicker or blur or the picture does not fit in the display area after performing the Auto Adjust manual adjustments are required Both adjustments should be made by using the screen adjustment pattern Test bmp
19. ct the problem discontinue using the monitor and contact your dealer or iiyama service center for further assistance Problem The picture does not appear Power indicator does not light up Power indicator is blue Power indicator is orange The screen is not synchronized The screen position is not in the center 4 The screen is too bright or too dark 5 The screen is shaking Check O The Power Cable is firmly seated in the socket L1 The Power Switch is turned ON O The AC socket is live Please check with another piece of equipment O If the blank screen saver is in active mode touch the keyboard or the mouse O Increase the Contrast and or Brightness O The computer is ON L1 The Signal Cable is properly connected O The signal timing of the computer is within the specification of the monitor O If the monitor is in power management mode touch the keyboard or the mouse O The computer is ON O The Signal Cable is properly connected O The signal timing of the computer is within the specification of the monitor L1 The Signal Cable is properly connected O The signal timing of the computer is within the specification of the monitor O The video output level of the computer is within the specification of the monitor O The signal timing of the computer is within the specification of the monitor L1 The video output level of the computer is within the specification of the mo
20. e zebra pattern The picture may flicker during the Pixel Clock H Position and V Position adjustment W n case the picture frame is bigger or smaller than the data display area after the Pixel Clock adjustment repeat steps from 3 22 OPERATING THE MONITOR Adjust the Phase to correct horizontal wavy noise flicker or blur the zebra pattern W case the strong flicker or blurs remain on a part of the screen repeat steps 6 and 7 because the Pixel Clock may not be adjusted correctly Adjust the H Position after the Phase adjustment if the horizontal position moves during the adjustment Adjust the Brightness and Color to get the desired picture after you complete the Pixel Clock and Phase adjustments Put back your favorite wallpaper OPERATING THE MONITOR 23 ENGLISH ENGLISH POWER MANAGEMENT FEATURE The power management feature of this product complies with power saving requirement of ENERGY STAR and VESA DPMS When activated it automatically reduces unnecessary power consumption of the monitor when your computer is not in use To use the feature the monitor needs to be connected to a VESA DPMS compliant computer There is a power management step the monitor takes as described below The power management function including any timer settings is configured by the operating system Check your operating system manual for information on how this can be c
21. ext For text editing and viewing in a word processing environment j Style Color is disabled when Blue Light Reducer is activated Blue Light Reducer Pressing and holding of the EXIT Button for 1 2 seconds when the Menu is not displayed Off Normal Mode Blue light is reduced Mode2 Blue light is reduced more than 1 Mode3 Blue light is reduced more than Mode2 Blue Light Reducer is disabled when i Style Color is activated e Lock Mode OSD Menu 1 The OSD lock will be activated by pressing the front button ENTER for about 10 seconds If you try to access the OSD by pressing any of the buttons message OSD Locked will appear on the screen 2 The OSD lock will be deactivated by pressing the front button ENTER again for about 10 seconds Power Switch 1 The power switch lock will be activated by pressing the front button for about 10 seconds Locking the power switch means that won t be able to turn off the Monitor while the power switch is locked If presses the power switch message Power Button Locked will appear on the screen 2 The power switch lock will be deactivated by pressing the front button again for about 10 seconds 20 OPERATING THE MONITOR SCREEN ADJUSTMENTS Adjust the image by following the procedure below to get the desired picture when selecting Analog input The screen adjustments described in this manual are designed to set image position and minimize fli
22. factory with the COMPLIANT TIMING shown on page 29 You are also able to adjust the picture by following the button operation shown below For more detailed adjustments see page 21 for SCREEN ADJUSTMENTS Press the ENTER Button to start the On Screen Display feature There are additional Menu items which can be switched by using the 4 Buttons Main Menu Auto Adjust 3 Language ro Luminance Recall Geometry Miscellaneous Color Input Select OSD X Audio 2 Select the Menu item which contains the adjustment icon relating to the adjustment you want to make Press the ENTER Button Then use 4 Buttons to highlight the desired adjustment icon Press the ENTER Button again Use the lt Buttons to make the appropriate adjustment or setting Press the EXIT Button to leave the menu and the settings you just made would be automatically saved For example to correct for vertical position select Menu item of Geometry and then press the ENTER Button Then select ca V Position by using the lt q gt Buttons An adjustment page appears after you press the ENTER Button Main Menu Geometry Auto Adjust Language H Position Luminance Recall V Position Geometry Miscellaneous Color Input Select Pixel Clock Phase osD Q Audio Then use the 44 Buttons to change the vertical position settings The vertical position of the overall display should be changing accord
23. iiyama USER MANUAL Pro Lrte LCD Monitor B2482HD Prolrte E2482HD Thank you very much for choosing the iiyama LCD monitor We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor Please keep this manual in a safe place fo your future reference E ob ENERGY STAR Servicecard Dear user we congratulate you on the purchase of your iiyama LCD For details on warranty and locally used pixel policies that apply directly after installation of your product please check the iiyama website To report a fault please contact your local support centre found at www iiyama com service Things to check before you call the iiyama information line if the power cable is connected securely and turned on if the display has been turned on if the signal cable is connected securely and the correct input selected if the computer has been restarted with the display connected if the graphics card is correctly installed with the latest drivers possible if the correct native resolution has been selected via Display Properties If the R G B signal configuration is correct if the displays On Screen Menu is shown if the correct brightness and contrast settings have been set if given display tolerances and compatibility have been considered if via the On Screen Menu you have performed a Factory Reset Recall
24. ingly while you are doing this Geometry rm V Position lt gt 50 Press the EXIT Button lastly it ends all changes are saved the memory m When button operations are aborted during adjustment On Screen Display disappears when the time set for the OSD Time has passed Also press the EXIT button to quickly turn off the On Screen Display Any changes are automatically saved in the memory when the On Screen Display disappears Turning off the power should be avoided while using the Menu Adjustments for V Position Pixel Clock and Phase are saved for each signal timing Except for these adjustments all other adjustments have only one setting which applies to all signal timings 14 OPERATING THE MONITOR ADJUSTMENT MENU CONTENTS ZJ Auto Adjust Adjustment Item Problem Option Button to Press iet Adjust H V Position Pixel Clock and Phase Auto Adjust Direct automatically For best results use the Auto Adjust in conjunction with the adjustment pattern See page 21 for SCREEN ADJUSTMENTS You can skip the Menu items and display an adjustment scale directly by using the following button operations Auto Adjust Press the Auto Button when the Menu is not displayed A x12 Xy Luminance Adjustment Item Problem Option Button to Press VV gt Xx Brightness Too bright 4 0 Contrast Tog dull E Too intense lt
25. ity 10 to 8096 No condensation Storage Temperature 20 to 60 4 to 140 F Humidity 5 to 8596 No condensation CE T V GS VCCI B CU ENERGY STAR Weird The height of the top of the monitor except the stand height APPENDIX 27 ENGLISH ENGLISH SPECIFICATIONS ProLite E2482HD 28 APPENDIX 24 TN Diagonal 24 61cm 0 277mm H x 0 277mm V 250cd m Typical 1000 1 Typical Adv Contrast Function Available Right Left 85 degrees each Up Down 80 degrees each Typical 5ms Typical Approx 16 7M Horizontal 30 0 80 0kHz Vertical 55 75Hz 1920 x 1080 2 1 MegaPixels VGA D sub mini 15 pin DVI D 24 pin VESA DDC2B Separate sync TTL Positive or Negative Analog 0 7Vp p Standard 75Q Positive Digital DVI Digital Visual Interface Standard Rev 1 0 compliance 531 4mm W x 298 9mm 20 9 W x 11 8 H 100 240VAC 50 60Hz 1 5A 24W typical Power management mode 0 5W maximum Energy Efficiency Class A 565 5 x 412 0 x 203 0mm 22 3 x 16 2 x 8 0 WxHxD 3 3kg 7 27105 Upward 22 degrees Downward 5 degrees Operating Temperature 5 to 35 41 to 95 F Humidity 10 to 8096 No condensation Storage Temperature 20 to 60 4 to 140 F Humidity 5 to 85 No condensation CE T V GS VCCI B CU ENERGY STAR DIMENSIONS ProLite B2482HD 565 5mm 22 3
26. ma service center Recycle information is obtained via the Internet using the address http www iiyama com You can access the Web page of different countries from there W We reserve the right to change specifications without notice W All trademarks used in this user manual are the property of their respective owners W As an ENERGY STAR Partner iiyama has determined that this product meets the ENERGY STAR guidelines for energy efficiency ENGLISH ENGLISH TABLE OF CONTENTS FOR YOUR SAFETY e ete tange cesa 1 SAFETY PRECAUTIONS ttr ht e setas 1 SPECIAL NOTES ON LCD 3 CUSTOMER SERVICE tente teret oe ea 3 CREANING dt ette nee t c ve eet 3 BEFORE YOU OPERATE THE MONITOR 4 FEATURE S 4 CHECKING THE CONTENTS OF THE PACKAGE 4 WALE MOUNTING doe ee tud tene 5 FITTING AND REMOVAL OF BASE ProLite B2482HD 6 FITTING AND REMOVAL OF BASE ProLite E2482HD 7 CONTROLS AND CONNECTORS ProLite B2482HD 8 CONTROLS AND CONNECTORS ProLite E2482HD 9 CONNECTING YOUR MONITOR ProLite B2482HD 10 CONNECTING YOUR MONITOR ProLite E2482HD 11 COMPUTER SETTING ttn energie iet tenens 12 ADJUSTING THE VIEWING ANGLE
27. nitor OThe power voltage is within the specification of the monitor LIThe signal timing of the computer is within the specification of the monitor TROUBLE SHOOTING 25 ENGLISH ENGLISH RECYCLING INFORMATION For better environment protection please don t dispose your monitor Please visit our web site www iiyama com recycle for monitor recycling 26 RECYCLING INFORMATION APPENDIX Design and specifications are subject to change without prior notice SPECIFICATIONS ProLite B2482HD 24 TN Diagonal 24 61cm 0 277mm H x 0 277mm V 250cd m Typical 1000 1 Typical Adv Contrast Function Available Right Left 85 degrees each Up Down 80 degrees each Typical 5ms Typical Approx 16 7M Horizontal 30 0 80 0kHz Vertical 55 75Hz 1920 x 1080 2 1 MegaPixels VGA D sub mini 15 pin DVI D 24 pin VESA DDC2B Separate sync TTL Positive or Negative Analog 0 7Vp p Standard 75Q Positive Digital DVI Digital Visual Interface Standard Rev 1 0 compliance 531 4mm W x 298 9mm 20 9 W x 11 8 H 100 240VAC 50 60Hz 1 5A 24W typical Power management mode 0 5W maximum Energy Efficiency Class A 565 5 x 386 5 516 5 x 230 0mm 22 3 x 15 2 20 3 x 9 1 WxH xD 5 0kg 11 02Ibs Upward 22 degrees Downward 5 degrees Left Right 45 degrees each Operating Temperature 5 to 35 41 to 95 F Humid
28. onfigured m Power Management Mode When the H sync signal V sync signal H and V sync signals from the computer are off the monitor enters into Power Management Mode which reduces the power consumption to less than 0 5W The screen becomes dark and the power indicator turns to orange From Power Management Mode the image reappears in several seconds when either the keyboard or the mouse are touched again Power Indicator NORMAL MODE gt Blue POWER MANAGEMENT MODE 7 4 POWER 0 0 5W 100 CONSUMPTION Even when using the power management mode the monitor consumes electricity Turn off the Power Switch whenever the monitor is not in use during the night and weekends to avoid unnecessary power consumption E It is possible that the video signal from the computer may be on while the H or V sync signal is missing In this instance the POWER MANAGEMENT feature may not work properly 24 OPERATING THE MONITOR TROUBLE SHOOTING If the monitor fails to operate correctly please follow the steps below for a possible solution 1 Perform the adjustments described in OPERATING THE MONITOR depending on the problem you have If the monitor does not get a picture skip to 2 2 Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists 3 If you are experiencing a problem which is not described below or you cannot corre
29. ort the weight of the monitor before mounting it Screw Mounting Stage Chassis BEFORE YOU OPERATE THE MONITOR 5 ENGLISH ENGLISH FITTING AND REMOVAL OF BASE ProLite B2482HD Put the monitor on a stable surface The monitor may cause injury or damage if it falls or is dropped W Do not give a strong impact to the monitor It may cause damage Unplug the monitor before removal or installation to avoid electric shock or damage Installation D Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched Lay the monitor flat on a table with front face down 2 Hold the monitor and push the Stand Base Use thumb screw provided to secure base to monitor column Stand Base E SE n b for Stand Base fixi screw fixing lt Removal gt Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched Lay the monitor flat on a table with front face down Remove thumb screw to remove base from monitor column lt Stopper gt 1 Put the monitor flat surface Press the stopper at the back of the stand while pushing the monitor from the top Careful attention is required as the monitor is sprung loaded and the stand may expand quickly Stopper
30. r to the monitor with the signal cable Connect the monitor to the audio equipment with the Audio Cable for computer when using the audio features 4 Connect the Power Cable to the monitor first and then to the power supply 5 Turn on your monitor and computer B The signal cables used for connecting the computer and monitor may vary with the type of computer used An incorrect connection may cause serious damage to both the monitor and the computer The cable supplied with the monitor is for a standard connector If a special cable is required please contact your local iiyama dealer or regional iiyama office m For connection to Macintosh computers contact your local iiyama dealer or regional iiyama office for a suitable adaptor m Make sure you tighten the finger screws at each end of the signal cable The Class pluggable equipment Type A must be connected to protective earth W The socket outlet shall be installed near the equipment and shall be easily accessible Example of Connection Back O gt VGA D sub Signal Cable e Not Included Power Cable S DVI D Cable Accessory Computer VGA D Sub cable is not supplied with the monitor you need to use a special VGA D Sub cable dedicated for this model Please contact the Support Centre
Download Pdf Manuals
Related Search