Climastar User
Contents
1. button Note If Hui Automatic Mode is selected the heater cannot be turned off To turn off the device Press the button and use 8 and Y buttons to select Ana Manual Mode then Press the OK mode button You can now turn off the device using the button 3 6 PILOT WIRING MODE In this mode the device works following instructions from an external controller How to select FP mode a Press the OK mode button b Press the button until F H is displayed and press the OK mode button c The display will show the set temperature together with a red flashing dot that indicates the unit is working in FP mode Note lf F P mode is selected the heater cannot be turned off To turn off the device press and using the Y buttons select Manual Mode then Press the OK mode button You can now turn off the device using the Dlesc button 3 KEY BLOCK FUCTION This function enables to block the controls To set this function do as follows a Press the OK mode button for a few seconds until I LUnF IG Configure Time is displayed b Repeatedly press the 4 button until 4 PrUEELEEd is displayed and then press the OK mode button c Press the 4 button until UN is displayed and then press the OK mode button The display now shows to indicate the controls are now locked To unlock the device wait until the dashes disappear and the display shows the temperature2. H 09 H 0H 1H 2H 3H 4H 5H 16H 17H 18H 19H 20 H 21H 22 23 H Before setting the device take into account the following OFF the device is programmed to switch off Frost protection if heater goes below 7 C ECO economy temperature 3 C below set temperature i e Comfort temperature set by user is 21 C then the ECO temperature would automatically set to 18 C ON comfort temperature As set by the user this temperature can be modified in the manual or automatic mode when the temperature is shown on the display 3 4 AUTOMATIC MODE continued How to select and carry out custom programming a Press the OK mode button b Select the auto mode by pressing the 4 button until HuiE Automatic Mode is displayed and press the OK mode button to confirm c The display will now show the set temperature together with a red dot that indicates the unit is working in automatic mode If the unit has been programmed previously then it may show HOFF d Press the OK mode button for a few seconds until i LunFi amp Configure Time is displayed e Press the 4 button and then press the OK mode button on e SELELE Select Day f Press and Y buttons to select the day you wish to change the on off times and then press the OK mode button 9 The display now shows UU or or 0 UU on depending on how it was previously programmed The indicates the time in hours i e OO 12 00am 1
3. Regulations e The use of these heaters is forbidden in any area where there is a presence of gases explosives or inflammable objects e Neither the connecting cable nor any other object must come into contact with the hot unit e Before connecting the heater check that the supply voltage is the same as that stated on the heater e WARNING To avoid overheating NEVER cover or obstruct in any way the heat outlet slots at the top of the heater or the air inlet slots at the base of the heater e DO NOT cover the heater Do not place material or garments on the heater or obstruct the air circulation around the heater e his heater should be switched off at the isolating switch before any repair work is carried out This action should also be taken during the times of the year when heat is not required e The radiator should not be installed just below an electrical socket or in front of a socket outlet e The appliance must be installed in such a way that switches and other control devices cannot be touched by a person using a bath or shower e installation must be carried out in accordance with the current electrical regulations The heater is fitted with a flexible cable size x 1 00 mm2 for electrical connection It may be used to connect the heater to the fixed wiring of the premised through a suitable connection box positioned adjacent to the heater e The supply circuit to the heater must incorporate a double pole isolating switc
4. service For your additional peace of mind Climastar UK gives the following Warranty Your statutory rights are not affected by this Warranty Subject as provided below Climastar UK warrants to the original purchaser at the original installation site that its products will be free from defects in materials electronic components and workmanship for the period of 5 Five years The original purchaser s remedy for breach of this Warranty is expressly limited to repair or replacement of any part or parts found to be defective under conditions of normal service and use during the above Warranty period and does not extend to Climastar UK being liable for any incidental special or consequential damages or losses whatsoever Such as loss of use of the product inconvenience or lost profits This Warranty does not cover any defect damage or malfunction in the product which is due to failure to comply in any respect with Climastars installation maintenance or operating instructions faulty storage handling installation or repair mis use neglect accident abuse or general wear and tear To ensure that our products provide you with the service that we expect it is important that they are installed in accordance with the British Electrical Standards and Approved codes of Practice Before free service under this Warranty can be provided the original purchaser will be required to prove the date of purchase and may be required to provide Climastar UK
5. then press and hold down the O esc button for 5 seconds until the dashes are shown again now press the button to confirm 3 8 SOUND FUNCTION The SOUND function enables you to activate and deactivate the beep emitted on touching the buttons To activate or deactivate the sound do as follows a Press the OK mode button for a few seconds b Repeatedly press the 8 button until 5 50 is displayed and then press the OK mode button c Press the 4 button to select Un to activate or UFF to deactivate the beep and press the OK mode button to confirm 3 9 OTHER INFORMATION e lf you enter a submenu and stop using the device for a few seconds it will automatically return to the main menu e lf you in the main menu and the device is not being manipulated it will turn to stand by mode and the display will only show a dot To turn on the screen again press any key on the button panel e Even if the device is in an OFF cycle the radiator can still start working This is because it has a minimum frost protection set temperature as per factory set to 7 C This mode is called FROST PROTECTION and it prevents the room temperature going below 7 C temperature device also has a built in sensor that detects any sudden temperature changes that may occur i e when a window is opened air conditioners activated or any other circumstance that may prevent the radiator from raising the room temperature This mode activates
6. weather e Do not use solvents or abrasive products for cleaning After the heating season turn off the radiator with the switch located on the right side of the radiator This inertia radiator has been manufactured under an assured quality system using environment friendly processes e Disposal Please take the radiator to a recognised disposal point so any useful material is recycled in the right way 6 Technical Specifications SMART EASY TECH and SMART TOUCH NN moo NE NN THERMOSTAT TOUCH VERSION Temperature range from 15 to 28 C EASY TECH VERSION Temperature range from 18 to 24 C SAFETY THERMOSTAT Number of Thermostats Rated Temperature 90 5 C Reset Temperature 65 10 C TYPE OF PROTECTION a 10 7 FAQs PROBLEM PROBABLE CAUSE SOLUTION The room does not reach the desired temperature he radiator does not operate Appearance of stains on the wall just above the radiator The display does not work No response from buttons The display shows a red dot Temperature does not go below 15 C The Incorrect setting of the set temperature Improper sizing the heater is too small for the room Lower and Upper grids are obstructed oet temperature below the room temperature The Cresc button has been pressed and the heater is turned off The switch at the side of the heater is turned to the off position The set program is in an OF
7. when the temperature decreases by 3 C in 5 minutes At this stage the radiator turns off and shows UPEN on the display this mode stays until this decreasing tendency disappears 4 Using the Smart EASY TECH Inertia Radiators 4 1 STARTING THE DEVICE After connecting the power cable to a mains power outlet click the switch on the right Press the C button to turn on the radiator ECO light turns on 4 2 SET UP TEMPERATURE Once the unit is ON press the button to select the desired temperature See images below CLIMASTAR CLIMASTAR CLIMASTAR 24 4 3 SELECT THE OPERATING MODE There are 4 operating modes e Manual The user determines the set point temperature e Timer The user selects both the set point temperature and the operating time or downtime e Replay The user selects desired temperature and time duration The unit automatically will start and stop e Pilot Wiring Manual Mode To select temperature press the button repeatedly until the light activates on the desired temperature see figures 2 2 Timer Mode Setting the heater to stay ON for a set amount of time 1h 4h 5h 8h 9h 12h 13h The device will work at the preset temperature as per user s configuration a Press the button to select the desired temperature b Now press the 3 button to select the operating time By pressing the 3 button repeatedly operating hours or a combination of operating hours will be selecte
8. with supporting information as Climastar UK may need to conduct its investigation into the alleged defect Climastar UK reserves the right to make reasonable charges for the inspection and testing of any product which is subject to a Warranty claim and the rights conferred by the Warranty are conditional upon the payment of such charge The charge may be made at Climastar UK s discretion either before or after the inspection and testing of the product In the event that it is established to Climastar UK s reasonable satisfaction that a valid Warranty claim has been made in respect of the product then any charges which has been paid will be refunded in full by Climastar UK 12 STAR Climastar UK Unit 3 East Bond Street Leigh Lancashire WN7 1BP Tel 01942 670158 Fax 01942 262221 www climastar co uk
9. 01 00 and so h By using the 4 and buttons you can select oF OFF JEn ECO or ON for that time period Once selected Press the OK mode button to move onto the next time period i Repeat step h until you go through all the 24 hours The display will now show P SELELE dH allowing you to select the next day to program Press the OK mode button and continue from step f if you wish to program each day individually Alternatively you can copy one day to the next by following steps in section 3 5 COPY FUNCTION step b 3 5 COPY FUNCTION This function enables you to copy a previously programmed day to any other day i e day1 to day2 or day1 to day5 etc To copy the setting of one day into another do as follows a Press the OK mode button for a few seconds until i LUnF 16 ELE Configure Time is displayed b Press 4 button until 3 LOPY dA is displayed and press the OK mode button c Press 4 button to select the day you wish to copy and press the OK mode button d The display will now show Iz des etc depending on which day you selected The first number is the day you are copying from the second number is the day you are copying too e By Pressing 4 button you can now change the day you want to copy too once happy Press the OK mode button to copy f You are now taken back to j LUFH menu where you can Press the OK mode button to copy another day repeat from step c or exit by Pressing the
10. F period Dust Carpet fibers or smoke fumes going through the heater Disconnection from power supply Control panel has been locked to prevent pressing of buttons After a short amount of time if no buttons have been pressed the display goes into stand by mode The heaters temperature is at its limit Check the set temperature on the display to verify it is the desired temperature The power rating of the heater is not adequate for the place in which it has been installed Select a larger heater Do not place anything on top or below the radiator Rise the radiators set temperature until it is 1 degree above the room temperature Press the Desc button and turn on the display shows ON Set the switch at the right side of the heater to position l Check that the set program is correct for the time period and change if necessary or put in manual mode and override Vacuum any dust and loose carpet fibers below the heater Refrain from burning candles or smoking in the same room Make sure power is going to the device and it is turned on Refer to key locking function section 3 7 Press any button and the display will activate The heaters temperature range is 15 28 C display shows Thedevce is bocked Press button POWER ESC during 4 seconds and press dashes the DOWN arrow 8 Warranty Terms and Conditions Your CLIMASTAR product has been designed and tested to give you many years of trouble free
11. INSTALLATION AND USER S GUIDE STAR A ZB 22 2 A yn 4 yn Smart EASY TECH version Smart TOUCH version SMART INTERTIA RADIATORS IM INE OD UG TIO IN Mem 2 2 INSTAEEATION INSTRUCTIONS aaa 3 3 USING THE INERTIA RADIATOR SMART TOUCH RANGES 1 eee eere nennen 4 3 1 Starting the Smart Touch RadlalO amina ls 4 3 2 Setting the Date 2 2 dnd dud 4 3 39 Manual MOE is T M n 5 34 Automatuc MOCGO oiii o 00040 EE ez oe SEES 5 PHOT WINO MOOO teet 6 36 CODY FUN CM 6 KEV BIOCK FUNCION tn 7 3 6 SOUNA FUNCIONA 7 3 9 Other NA o 7 4 USING THE INERTIA RADIATOR SMART EASY TECH RANGES 8 4 1 Starting the Smart Easy Tech 8 A 2 UD eet 8 4 3 Selecting the Operating Mode isisisi sisara ian ia iaaiiai 8 5 CLEANING AND MAINTENANCE 9 6 TECHNICAL SPECIFICATION Susini 10 a 11 8 WARRANTY TERMS AND 12 1 Introduction e he warranty of the heater will not cover any damage caused by non observance of any of these instructions e This guide must be kept an
12. Y buttons adjust the minutes to the current time and press the OK mode button e The display now shows DAY 1 use the 4 and Y buttons to select the current day of the week i e DAY 1 is Monday DAY 2 is Tuesday Etc and then press the OK mode button f The display now shows i LunFi amp Configure Time again Press the O esc button The date and time are now set Your device is now working 4 3 3 MANUAL MODE In this mode the device works using factory settings All you have to do is press ft to select the desired temperature The set temperature can be modified from 15 C to 28 C in intervals of 0 5 C How to select the manual mode a Press the OK mode button b Select the mode by pressing 4 or Y buttons until Ana Manual Mode is displayed and press the OK mode button to confirm c Now select the desired temperature by pressing 8 and buttons The heater will now operate and cycle on and off up to the desired temperature Note The FROST setting automatically activates to prevent temperatures going below 79C To activate this setting simply press the Olesc Power button to turn the heater off the display should show OFF 3 4 AUTOMATIC MODE In this mode the device works on the programmed time schedule It can work as per factory set see table below or according to the user s configuration TIME MONDAY TUESDAY WEDNESDAY THURSDAY FRIDAY SATURDAY SUNDAY 01H 02 H 03 H 04H 05H 06 H 07H 08
13. d e g CLIMASTAR O 252 The above example shows the device programmed to be ON at 21 C for 5 hours To deactivate the timer function press the 3 button repeatedly until the time LEDs are all deactivated Timer Mode continued Setting the heater to stay OFF for a set amount of time 1h 4h 5h 8h 9h 12h 13h The device will stay off as per the user s configuration and then turn on to the set temperature a On starting the device again press the button to select the temperature to reach b Press the gt button for 2 seconds to switch to OFF mode c Press the button to select the switch off time of the device d Now press the 3 button to select the operating time By pressing the 9 button repeatedly operating hours or a combination of operating hours will be selected e g CLIMASTAR 22 19 Smart ia 8h th program The above example shows the device is programmed to be OFF for 5 hours To deactivate the timer function press the 3 button repeatedly until the time LEDs all deactivated 5 Cleaning and Maintenance e The radiators do not require any special maintenance providing thermal comfort during large periods Dust clean with a dry soft cloth only when the unit is disconnected and cold Atthe beginning of the year s heating season vacuum any dust that has accumulated in the inner heating element while the radiator has been off for long periods during warmer
14. d given to any new owner e IMPORTANT SAFETY ADVISE When using electrical appliances basic precautions should always be followed to reduce the risk of fire electrical shock and injury to persons including the following e IMPORTANT If this heater is installed in a room containing a bath or shower it should be so installed that switches and other controls cannot be touched by a person using a bath or shower e The installation of this product should be carried out by an electrician or competent person and be in strict accordance with the current IEE Wiring Regulations and relevant Building Regulations e The heater must be installed in accordance with these instructions e The heater must be mounted using the wall bracket supplied e The heater should be positioned in accordance to the clearances stated in these instructions e WARNING THE SURFACE OF THIS HEATER CAN BE HOT Momentary contact with any part of the heater should not cause injury However aged or infirm persons or young children should not be left unsupervised in the vicinity of the heater unless a suitable guard is fitted e Not intended for use by children or persons with reduced physical sensory or mental capabilities Cleaning and maintenance must not be carried out by children without supervision e The heater must be installed moved or installed by an electrician or competent person and be in strict accordance with the current IEE Wiring Regulations and relevant Building
15. elled then fix the screw of lower bar too Horizontal and square radiator Vertical radiator Once the heater is on the wall support proceed to screw the support to the lower part of the heater 3 Using the Smart TOUCH Inertia Radiators 1 POWER O esc button Turn on and off 1 the device allows moving back from any menu 2 OK mode button to access main menu and select or confirm the desired option 3 UP DOWN arrows 8 Y allows you to set the values and navigate through the different options of the menus 4 DISPLAY shows the different options and desired values 5 RED DOT if flashing the device is working in PILOT WIRING mode if not then it is working in automatic as per the set programming inertial system by CLIM ASTAR Lu 3 1 STARTING THE DEVICE After connecting the power cable to a mains power outlet click the switch on the right The display starts shows a welcome message and shows OFF To start the device press Power button and the set temperature appears on the screen 3 2 SETTING DATE AND TIME a Press the OK mode button for a few seconds b The display shows i LunFi amp Configure Time If not press 8 until you see it and press the OK mode button c The display shows Hours using the 8 and buttons adjust the hours to the current time and press the OK mode button d The display now shows N Minutes using the 4 and
16. h having a contact separation of at least 3 mm lf the supply cable is damaged it must be replaced by the manufacturer its after sales service agents or any other competent qualified person e All models are supplied with an electrical interrupt cut out This will switch off the heater if for any reason it overheats Should the cut out operate turn the heater off and remove the cause for the overheating The cut out will be reset automatically e The presence in air of particles of smoke dust and other pollutants could in time discolour the walls and surfaces around the heater 2 Installation Instructions Open the package and check that it is the correct model and it is in good condition To obtain optimum performance it is necessary to maintain a minimum clearance of 15 cm between the radiator and any inflammable material as furniture curtains etc Recommended clearances required to maintain optimum performance are indicated on the following picture Once you have decided the location to install the device remove the packaging and extract the device and its mounting kit This kit has to be assembled for safety Fix the support to the wall using it as a pattern A correct stabilization of the support clamp is required The image below shows where to drill to fix the support recommended distance Note first fix the screws of the upper part to the wall with appropriate rawl plugs once the support is properly lev
Download Pdf Manuals
Related Search