Hood User Manual
Contents
1. You can procure carbon filter from Ar elik Authorized Dealers 1 Remove the aluminum filters 2 Take the carbon filter out from its seat by pulling 3 Install the new carbon filter 4 Install the aluminum filters Use a soft cloth soaked with liquid detergent to clean the outer surface of your hood JAN WARNING Never use abrasive or scratching materials for cleaning 12 13 EN Hood User Manual 5 Cleaning and Care WARNING You may cause a fire if you do not follow the instructions on the cleaning and replacement of the filters of your hood A 5 3 Replacement of the lamp 2 pieces of 20 W halogen lamps are used in your hood Prior to replacement of lamp unplug the appliance or turn the main switch off or loosen the fuse that supplies the hood or turn it off To remove the holder of the halogen lamp take the amp holder out by rotating it counterclockwise Be careful not to drop the lamp holder during this order of the removal procedure We advise you to Contacting halogen lamps with bare hands will reduce their service life operation After replacing the lamp install the lamp holder by rotating it clockwise following the reverse install the new lamp with a piece of cloth or gloves Note e You may procure lamps from Authorized Dealers If you need to transport the unit e Keep original package Transport the unit with its original package and follow the tr2. Litre 400 Litre 200 00 gt 400 Litre 600 Litre 300 00 gt 600 litre 350 00 Subject to a valid claim under the terms and conditions of this Guarantee To be eligible for this Guarantee the product must be purchased from an Authorised Reseller in Australia or New Zealand What is not covered under this Guarantee 1 Any service calls in which the problem is found not to be caused or related to any defect in the Product In this instance the cost of the service call will be charged to you Examples but not limited too of no product fault listed below a Correcting the installation e g levelling of product adjust ment of drain crossed or kinked hoses leakage of hoses if incorrectly fitted removal of transit bolts front loading wash ers noises due to water hammer and or power supplies b Replacing fuses or correcting house power wiring or house plumbing issues c Failure due to incorrect set up or requiring instructions nor mally covered in user manual d Blocked pumps removal of foreign objects substances from the washing machine e g socks bra wires dirt etc e Normal noise or vibration f Infestation of pests insects or vermin 2 This Guarantee does not cover damage caused by Misuse or abuse of the Beko Product Accidental damage of any kind Rust and Corrosion where the product is located within a cor rosive environment Discolouration of burners or trivets on gas cooktops or chrome surroun
3. the air in the kitchen Ensure that fresh air enters the kitchen espe cially when the hood is operated together with the gas hobs Ensure that the flue connection of the unit is not connected to flues used to discharge smoke caused by non electric devices E g Radiator flues If there is non electric appliance in the same room with the hood the negative pressure inside the room should be maximum 0 4 mbar to pre vent the suction of the waste gas from the other appliance by the hood into the room again 1 2 Intended purpose e This appliance is intended for domestic use It is not suitable for commerical use and should not be used for any purposes other than the intended purpose e Manufacturer assumes no responsibility for any damage caused by misuse or improper trans port e Service life of the product you have purchased is 10 years This is the period required for availability of spare parts for functioning of the product 1 3 Child safety e Package materials are risky for children Keep the package materials out of reach of the chil dren e Electrical appliances are risky for children Keep the children away from the unit when it is oper ated Do not let them play with the product 1 4 Compliance with the AEEE Directive and Disposal of Waste Products This product does not include harmful and prohibited materials specified in the Regulation for Supervision of the Waste Electric and Electronic Appli
4. 9101 78 R AA 27092011 www beko com
5. CWB 6601 X Hood User Manual BEKO Please read this user manual first Dear Customer Thank you for prefering a Beko product We hope that you get the best results from your product which has been manufactured with high quality and state of the art technology Therefore please read this entire user manual and all other accompanying documents carefully before using the product and keep it as a reference for future use If you handover the product to someone else give the user manual as well Follow all warnings and information in the user manual Remember that this user manual is also applicable for several other models Differences between models will be identified in the manual Explanation of symbols Throughout this user manual the following symbols are used Important information or useful hints about usage Warning for hazardous situations with regard to life and property Warning for electric shock Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations Q gt gt a Do not dispose of the packaging materials together with the domestic or other wastes Take them to the packaging material collection points designated by the local authorities This product was manufactured using the latest technology in environmentally friendly conditions TABLE OF CONTENTS 1 Important safety and environmen
6. ances issued by the Ministry of Environment and Urban Planning It complies with AEEE Directive This product has been produced from recyclable and reusable high quality compo nents and materials Therefore do not dispose of this product with the domestic wastes or other wastes at the end of its service life Take it to a collection center for recycling of electric and elec tronic appliances You can ask for these collection centers from your local administration Help pro tecting the environment and natural resources by recycling the used products 1 5 Package details Package of the product is made of recyclable materials as per our National Legislation Do not dispose of the package wastes with domestic wastes or other wastes bring it to the package collection centers specified by local au thorities aw ue Hood User Manual 5 13 EN Your Hood 2 1 Appearance 2 1 1 Controls and components 1 Lamp 2 Aluminu 3 Aluminu 4 Hood body m filter lock m filter 5 Control panel 6 Flue con 7 2 pcs of nection element wall fittings 8 1 pc of 120 mm flue connection adaptor 9 1 air deflector optional 2 2 Technical Specifications Width 600 mm Depth 500 mm Height Min 675 mm Max 1005 mm Supply voltage 220 240 V 50 Hz Control 3 positions Suction power 800 m h Motor power 230 W Lamp po
7. and Care Prior to maintenance unplug the appliance or turn the main switch off or loosen the fuse that supplies the hood or turn it off Clean your stainless steel hood with cleaning agents specifically produced for this material AN AN 5 1 Aluminum filter This filter is intended to retain the oil particles in the air You are recommended to clean your filter every month under normal usage conditions 1 Push the aluminum filter lock forward Note e You can wash your aluminum filters in dish washer also WARNING Never use rubbing mate rials wire wool or abrasive materi als brushes the harder side of the scouring sponge etc WARNING Sterilizers products made of carbon steel or similar mate rial containing chloride may cause black stains corrosion or permanent marks when they contact with stain less steel e A discoloration may be observed on aluminum filters as they are washed This is normal you do not need to replace your filter 2 Then slightly lower it and pull forward Otherwise you may bend the filter 3 Wash the filters with liquid detergent and then rinse them with water 4 When the filters are dried re install the filter in the reverse order of the above procedure 5 2 Carbon filter Flueless usage This filter removes the cooking odours fi WARNING Carbon filter should never be washed It should be replaced ev ery 4 months under normal usage
8. ansport mark ings on the original package If you do not have the original package e Do not put heavy objects on the hood e Protect the outer surface from impacts e Pack the unit so that it would not be damaged during transport Hood User Manual 13 13 EN Beko Manufacturers Guarantee Congratulations on purchasing a quality Beko product Beko automatically provide you with a 2 year Manufacturers Guarantee covering parts and labour for servicing within the geographical limits of Australia and New Zealand General Terms and Conditions For Australian Consumers This guarantee is an extra benefit and does not affect your legal rights Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure For New Zealand Consumers This guarantee is an extra benefit and does not affect your legal rights Nothing in this guarantee purports to modify or exclude the conditions guarantees and undertakings and other legal rights under the New Zealand Consumer Guarantees Act and other laws except in those circumstances contemplated by section 43 2 of the New Zealand Consumer Guarantees Act Beko Guar
9. antee The Beko Manufacturers Guarantee provides additional protection for your Beko Product and it identifies a preferred approach to resolving product claims which will allow for a quick and simple process for all parties subject to our terms and conditions below To enable us to assist you in the most expedient way please contact us by phoning the Toll free number relative to your country of residence as listed below Please ensure you refer to your user manual and in particular the section headed Recommended Solutions for the problems before phoning The commencement date of this guarantee starts on the day of purchase and proof of purchase must be supplied to the Beko Service Centre prior to commencement of any guarantee work Terms and Conditions Beko Australia and New Zealand Pty Ltd guarantees to the original purchaser to repair or at its option replace without charge to the owner for any part which is not of acceptable quality within two years of date of purchase No Lemon Guarantee if the product fails more than 2 times during the Guarantee period due to the same type failure caused by the same part we will automatically replace the product with an equivalent product free of charge Food Spoilage If your product is a fridge or freezer we will reimburse you for food which due to a valid fault as per our guarantee is spoilt reimburse you as per the benefits below Up to 200 Litre 100 00 gt 200
10. appliance is not intended for use by chil dren and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge Children should be supervised to en sure that they do not tamper with the appliance 1 1 1 Electrical safety e Always unplug the appliance from the mains supply during installation maintenance cleaning and repair operations If the power cord is faulty it should be replaced by a qualified person certified by the manufac turer after sales service or similar preferably electrician or a person described by the im porter Operating voltage is 220 to 240 volts Do not operate a faulty unit unless it is repaired by the authorized service Risk of electric shock Do not put power cord near cooktops This may cause a fire as the cord may be melted Do not plug in the hood before it is installed To achieve the best performance the length of the external conductor should not exceed 4 meters it should not have more than two 90 angles and its diameter should be at least 0120 mm e Disconnect the appliance before any intervention to the internal parts of the appliance 1 1 2 Product safety e You may use pipes with a diameter of 120 mm or 150 mm on the flue connection of your hood Do not make connections to the flues connected with stoves exhaust shafts or flues with rising flames Observe the rules set by authorities on the discharge of exhaust air The height bet
11. ds Incorrect operation or not following the operation instructions as stated in the user manual Improper installation Failure to clean or improper cleaning Use of incorrect non compliant electrical or gas connections External sources including but not limited to electrical inter ference power surges or voltage fluctuations Any loss caused by civil commotion Any loss caused from extreme events of nature including but not limited to flood cyclone severe storm and earthquake Use of non genuine authorised parts m Any repair or other work carried out on the Beko product other than by an Authorised Beko Service Personnel 3 This Guarantee does not cover costs associated with replacing and servicing of consumable parts E g lamps amp bulbs filters This Guarantee has been designed for Products used in normal domestic environment Our products are not designed for commercial use Any com mercial use may affect this Product s Guarantee Service under this Manufacturer s Guarantee is provided by the Beko Aus tralia and New Zealand Authorised Repairer The Guarantee is provided by Beko Australia and New Zealand Pty Ltd ABN 49 152 055 162 of 55 Blanck Street Ormeau QLD Australia 4208 PO Box 354 Ormeau QLD Australia 4208 In Australia if you need assistance Toll Free 1300 282 356 Email Beko care Beko com In New Zealand if you need assistance Toll Free 0800 69 2356 Email Beko care Beko com 4 285
12. electric switch that has a minimum clearance of 3 mm between the 3 pole terminals Have a qualified electrician perform the electric connection e Install your unit so that you can reach the elec tric connection plug outlet easily after instal lation 6 4x18 X2 25x45 X4 3 3 Installation of the Hood e Please consult the nearest Arcelik Authorized Service for the installation of the hood e Preparation of the installation place and electric wiring is the responsibility of the customer Hood User Manual 7 13 EN Set up e Observe the dimensions given in Figure 1 and drill 4 8 mm holes for X and Y and 4 6 mm holes for Z and H NCE 59 mm DGE 69 mm Place the screws to the Z holes so that a clearance of 8 mm is left Figure 3 e Use the screws and dowels in the equipment of the appliance for installation of various parts e Secure the bracket Figure 2 3 to the Z and H holes on the wall KO bec V After hanging the hood to the Y holes secure it to the wall using X holes inside the body Tighten Y screws Figure 4 8 13 EN Hood User Manual El Set up 3 4 Flue Set up 3 4 1 Usage without flue connec 1 Install 2 clamping screw seats to the left and tion right holes of the wall hanger Air is filtered by the carbon filter and returned to 2 Place the flue connection element freely onthe the room Carbon filter is used whe
13. n there is no body flue available in the house or when it is not pos 3 Pull the inner flue connection element upwards sible to install the flue pipe from the flue connection element placed over the body Figure 4 and screw the brackets to Z and axes from left and right sides Figure 5 1 Remove the aluminum filters 2 To install the carbon filter center the carbon filter on the plastic part on both sides of the fan body and secure it on the tabs 3 Reinstall the aluminum filters TA 900 700 600 Hood User Manual 9 13 EN El Set up 3 4 2 Usage with flue connection 4 Install air deflector i 5 Install the active carbon filter as follows Follow Vapors are discharged with the flue pipe secured the procedure in reverse order to remove on the connection ring on the hood Diameter of the flue pipe should be equal to the diameter of connection ring Pipe should be installed slightly inclined about 10 in horizontal layouts to allow the air to go out of the room easily AN WARNING Carbon filter should be removed if it is installed on the hood 1 For the installation of flue connected model con nect the hood to the outlet pipe with a rigid or flexible pipe with a diameter of 150 or 120 mm l depending on the pipe selection by the installer 6 Install clip screw seat to the wall hanger Figure 3 7 Pull the inner flue connection element upwards 2 Ins
14. tal instructions 1 1 General Safety recoin ake aie neiaa 4 1 1 1 Electrical safety 2 222 ceccccc 4 1 1 2 Product safety 22222222 4 1 2 Intended purpose 2 2 2222 5 1 3 Child safety u 5 1 4 Compliance with the AEEE Directive and Disposal of Waste Products 5 1 5 Package details 0 0 cee eee 5 2 Your Hood 6 2 1 Appearance seen eee ee 6 2 1 1 Controls and components 6 2 2 Technical Specifications 6 3 Set up 7 10 3 1 Preparation 0 eee eee ee 7 3 2 Power connection 0000ee eee 7 3 3 Installation of the Hood 005 7 34 Flue OCIUD nase 9 3 4 1 Usage without flue connection 9 3 4 2 Usage with flue connection 10 4 Operation of the Appliance 11 4 1 Control panel 00 eee 11 5 Cleaning and Care 12 13 5 1 Aluminum filter 00 0 0 cece eee 12 5 2 Carbon filter Flueless usage 12 5 3 Replacement of the lamp 13 Hood User Manual 3 13 EN 1 Important safety and environmental instructions This section contains safety instructions that will help you prevent injuries or material damages Any warranty shall be void if you do not observe these instructions 1 1 General Safety e Always have the installation and repair work performed by Authorized Dealers Manufacturing firm shall not be held responsible for damages that may be caused by unauthorized persons e This
15. tall the flue adaptor to the hood body outlet if from the flue connection element placed over you would like to install with a pipe with a diam he body Figure 4 and screw it to the hanger eter of 120 mm from left and right sides Figure 5 3 Secure the pipe with suitable clamps These WARNING In case of failure to perform cleaning and maintenance of oil filters items are not supplied with the unit Remove the regularly and whenrthe canon iii i l N ularly and when the carbon filter active carbon filters if any optional IN reaches its service life about 4 months there is the possibility of causing fire by them 10 13 EN Hood User Manual 4 Operation of the Appliance 4 1 Control panel 4 2 Operating the Hood e Hood is equipped with a motor with various speed settings For a better performance we advise you to use low speeds in normal condi tions and high speeds when smell and vapors are intensified 1 Press any of the speed setting buttons B C D to operate the hood in the required speed 2 You can illuminate the cooking area by pressing A Turning the lamp on off button A l 2 3 Press the speed setting button you pressed be a ak f ain to turn off the hood C Speed 2 ore agal urn off the hood D Speed 3 E Warning light Red warning light on the front panel is illuminated continuously when the motor is activated Hood User Manual 11 13 EN 5 Cleaning
16. ween the lower surface of the hood and upper surface of the stove oven should not be less than 65 cm Do not operate the hood without aluminum filters and do not remove the filters while it is operated Do not touch the lamps of the hood after oper ating the hood for a long time Hot lamps may burn your hand Do not cause high flames under the unit Other wise the oil in the oil trap filter may ignite and cause a fire Operate your appliance after putting a pot pan etc on the hobs Otherwise rising heat may de form some components of your unit Turn off the hobs before taking a pot pan etc from the hobs Do not keep easily flammable materials under your hood Oil may catch fire while making dishes such as fries etc For this reason be careful about the covers and curtains Do not leave the cooktops unattended while making dishes such as fries etc hot oil can cause fires There is a risk of fire if your hood is not cleaned in the specified periods Be very careful and use gloves when you are cleaning your hood 4 13 EN Hood User Manual 1 Important safety and environmental instructions e We advise you to operate the unit a few minutes before starting to cook in order to increase the suction power Thus you shall have a continuous and stable suction power when the vapors occur Operate your appliance for 15 minutes more after the end of cooking or frying in order to remove unpleasant smell from
17. wer 2X20 W Fuse 10A Aaa PP 120 180 mm Net weight 10 5 kg Gross weight 13 3 kg Color Inox Markings on the product or the values stated in other documents supplied with the product are values obtained under laboratory conditions as per relevant standards These values may vary according to the usage of the product and ambient conditions 6 13 EN Hood User Manual El Set up 3 1 Preparation N WARNING Remove the protective film if i i any on the hood and flue surface after Information required for the preparation of the the installation installation place for your hood is given below Dimensions are given in mm e Perform the transport operations with the origi P nal package of the unit observing the markings zu 70 on the package Protect your unit against factors p that may harm the package and the unit humid ity water impact etc e Hood should be placed as aligned by the central axis of the cooking unit The distance between the cooking unit and oil filters of the hood should be at least 65 cm e Perform the following steps for the installation of the hood min 615 max 945 3 9x19 X2 6x30 X4 WARNING The height between the A rf f the hood and ae should net be ee less than 65 cm 3 2 Power connection en ae e This appliance is manufactured with a supply cord with 3 threads and it should be connected to the mains supply with an
Download Pdf Manuals
Related Search