RPW105DM manual.indd
Contents
1. gun at all times EDEN GED AED EDENGOCDEDED ENGLISH Original Instructions m Pull back and hold the trigger to operate the pressure washer m Release the trigger to stop the flow of water through the nozzle To engage the lock out m Push down on the lock out until it clicks into the slot To disengage the lock out m Push the lock out up and into its original position For the most effective cleaning the spray nozzle should be between 20 cm and 60 cm from the surface to be cleaned If the spray is too close it can damage the cleaning surface USING THE NOZZLES Before starting any cleaning job determine the best nozzle for the job The 25 nozzle is for general purpose cleaning CAUTION A NEVER change nozzles without engaging the lock out on the gun and NEVER point the lance at your face or at others The Quick Connect collar contains small springs that could eject the nozzle with some force Failure to heed this may cause personal injury Using the Quick Connect collar changing nozzles is easy To connect a nozzle to the lance m Turn off the pressure washer and shut off the water supply Pull trigger to release water pressure m Engage the lock out on the gun by pulling down on the lock out until it clicks into the slot m Pull back the quick connect collar Push the nozzle into place in the spray wand Push the collar forward so that the nozzle is secured properly Check to see that the nozzle is sec2. off machine and purge pump by squeezing trigger gun until a steady flow of water emerges through the nozzle Water filter is clogged Remove water filter and rinse in warm wate Water leaks from pump Loose fittings Loose fittings Check that all fittings are tight up to 10 drops per min ute is permissible Water seals are damaged or Call the Toll Free Hotline worn Oil is dripping Oil seals are damaged or Call the Toll Free Hotline worn 11 ENGLISH Original Instructions Motor buzzes but fails Supply voltage below minimum Verify that only the pressure to run washer is running on this circuit System has residual pressure Turn unit OFF squeeze trigger on spray wand to release pressure then turn unit ON Voltage loss due to Unplug any extension cords attached extension cord and plug the unit directly into the outlet Pressure washer not used for Call the Toll Free Hotline long periods Residual friction among com Disconnect water supply and ponents Unit might hum power ON for 2 to 3 seconds repeat couple times or until the motor starts No Water Quick connect assembly is Verify that Inlet adapter G2 is attached in reverse attached to machine s water inlet and that the quick connect coupler G1 is attached to garden hose Water supply is OFF Turn ON water supply Kink in the garden hose Remove kink in garden hose DISPOSAL This marking indicates that t
3. warranty period This warranty does not cover transportation cost or consumable items such as fuses and batteries This limited warranty is void if the product s original identification trade mark serial number markings have been defaced altered or removed or if product is not purchased from an authorized reseller or if product is sold AS IS and or WITH ALL FAULTS Where permitted the provisions of this limited warranty are in lieu of any other written warranty whether express or implied written or oral including any warranty of MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT SHALL WE BE LIABLE FOR SPECIAL INCIDENTAL CONSEQUENTIAL OR INCIDENTAL DAMAGES OUR MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID BY YOU FOR THE PRODUCT This warranty is valid only in the European Union Australia and New Zealand Outside these arears please contact your authorized GreenworksTools dealer to determine if another warranty applies AUTHORISED SERVICE CENTRE ENGLISH Original Instructions EN EC DECLARATION OF CONFORMITY FOR MACHINERY Manufacturer Changzhou Globe Tools Co Ltd Address No 65 Xinggang Road Zhonglou Zone Changzhou Jiangsu 213000 P R China Name and address of the person authorised to compile the technical file Name Dennis Jacobson Director of Outdoor Power Equipment Address GLOBE TOOLS EUROPE AB tbyggargatan 14 120 68 Stockholm Sweden Herewith we declare that the product Catego
4. D SERVICE CENTRE for repair When servicing use only identical replacement parts WARNING A To avoid serious personal injury do not attempt to use this product until you read thoroughly and understand completely the operator s manual If you do not understand the warnings and instructions in the operator s manual do not use this product Call greenworks Tools customer service for assistance WARNING The operation of any power tool can result in foreign objects being thrown into your eyes which can result in severe eye damage Before beginning power tool operation always wear safety goggles or safety glasses with side shields and when needed a full face shield SAVE THESE INSTRUCTIONS ELECTRICAL DOUBLE INSULATION Double insulation means that exposed metal parts are isolated from the internal metal motor components with protecting insulation Double insulated products do not need to be grounded WARNING The double insulated system is intended to protect the user from shock resulting from a break in the product s internal insulation Observe all normal safety precautions to avoid electrical shock NOTE Servicing of a product with double insulation requires extreme care and knowledge of the system A and should be performed only by a qualified service technician For service we suggest you return the product to your nearest authorized service centre for repair Always use original factory replacement parts
5. ENANCE Avoid using solvents when cleaning plastic parts Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use Use clean cloths to remove dirt dust oil grease etc EDEN GEDA EPDEDGHGOCDEDED ENGLISH Original Instructions WARNING Do not at any time let brake fluids petrol petroleum based products penetrating oils etc come in contact with plastic parts Chemicals can damage weaken or destroy plastic which may result in serious personal injury Only the parts shown on the parts list are intended to be repaired or replaced by the customer All other parts should be replaced at an authorized service centre POWER SUPPLY CORD REPLACEMENT If replacement of the power supply cord is necessary this must be done by an authorized service centre in order to avoid a safety hazard NOZZLE MAINTENANCE See Figure 8 Excessive pump pressure a pulsing sensation felt while squeezing the trigger may be the result of a clogged or dirty nozzle m Unplug the pressure washer m Turn off the pressure washer and shut off the water supply Pull trigger to release water pressure m Remove the nozzle from the lance NOTE Never point the spray lance at your face a Using a straightened paper clip or nozzle cleaning tool free any foreign materials clogging or restricting the nozzle m Using a garden hose clear flush debris out of nozzle m Reconnect the nozz
6. FF machine and purge pump by squeezing trigger gun until a steady flow of water emerges through the nozzle Output pressure varies Not enough inlet water supply Turn water on fully Check garden high and low hose for kinks leaks or blockage Pump is sucking air Check that hoses and fittings are airtight Turn OFF machine and purge pump by squeezing trigger gun until a steady flow of water emerges through the nozzle Water inlet filter is clogged Remove filter and rinse with warm water 10 ENGLISH Original Instructions PROBLEM POSSIBLE CAUSE SOLUTION Unit does not reach Diameter of garden hose is Add more detergent high pressure too small Detergent bottle or suction Check connections tube not properly connected Detergent is too thick Dilute detergent Filter on detergent suction Run warm water through filter to tube is clogged remove build up Damaged or clogged deter Remove obstruction or replace gent suction tube detergent suction tube Nozzle is in high pressure Turn nozzle tip to low pressure position position Discharge nozzle is ob Blow out or remove debris with a structed fine needle Garden hose connection Loose fittings Tighten fittings leaks Missing worn rubber washer Insert new washer Spray wand extension Broken o ring or plastic insert Call the Toll Free Hotline or nozzle leaks Pump is noisy Pump is sucking air Check that hoses and fittings are airtight Turn
7. Maximum Water Temperature Rated Voltage ccasasecdecededbstdie Vencevenuasnoncshonasedsuceasabns edonon iied iadaa E aaie rN Rated Pressure sedete reae ae NE a a Oa aE A AN E a NE SAAE Permissible PreSSUTE siesdace sce ea cscgatcacsiestancapmnnends Cenvets ridada N aeaaaee eadair Pow t Ratihg cssescsecacncirsssisevsancesedssnancasxonanacadiassssesesscesadenduensascanasnibeisssedesvavansenadncrttcabir Meceeiweten Rated Water FIOW gecissee tsino veriden aaa aE a eE aE E E E a UAE a eS M ximum Water FION sprp riranna ENS PE a O EASI sean verdes a ELE TEESE Maximum Water Inlet Pressure a Maximum Water Inlet Temperature cccccssceeseeeseeeecceeeeuneeneeeaeeeessaueessaasaeceeeeeeenunaesaaeesessnecageesessnas 40 C LPA sound pressure level s t ttt ere erates nee tee tcteneteneta 82 dB A K 3dB A LWA sound power LEVON ssicccrsccsensinsacadecinansacnensasvansncesoanisagideneadanadinendnesantneeshundwseaadeanaiuandiaensons 94 dB A Protection DOOGS dncsiavirnrsvataninaractnerssnsatiadiensannabenbaissniaddoeptanaaianinnsnnssdbnbimiusaeisarinnnanianiiliecianessduaes IPX5 VIDVATON 0c2c2 ciencesktdasstacdacacaeaentesscssaadeabanadedscaweedidadacaaaefesaceasabebvdasendacacaaedsbiexadassiacsdbers 4 0 m s K 1 5 m s DESCRIPTION 1 On Off switch 2 Gun storage hook 3 Handle assembly 7 Electric cord hook 5 Water intake 6 Wheels 4 Electric cord storage hook 8 Detergent tank 10 Spray wand 9 High pressure cor Pa hos
8. and walls a Cleaning cars boats motorcycles outdoor furniture and barbeques ADDING DETERGENT TO THE PRESSURE WASHER See Figure 6 Use only detergents designed for pressure washers household detergents acids alkalines bleaches solvents flammable material or industrial grade solutions can damage the pump Many detergents may require mixing prior to use Prepare cleaning solution as instructed on the solution bottle NOTE Use a funnel if needed to prevent accidental spilling of the detergent outside the tank If any detergent is spilled during the filling process make sure the unit is cleaned and dried before proceeding STARTING AND STOPPING THE PRESSURE WASHER CAUTION Do not run the pump without the water supply connected and turned on Connect the garden hose Turn the garden hose on then squeeze the high pressure trigger to relieve air pressure Once a steady stream of water appears release the trigger m After ensuring the switch is in the OFF position connect the pressure washer to the power supply Press ON 1 on the switch to start the motor To stop the motor release the trigger and press OFF 0 on the switch NOTE Use a funnel if needed to prevent accidental spilling of the detergent outside the tank If any detergent is spilled during the filling process make sure the unit is cleaned and dried before proceeding USING THE GUN For greater control and safety keep both hands on the
9. e a ea W EDEN GEDA EPDEDENGOCDEDED ENGLISH Original Instructions DETERGENT TANK Remove the nozzle from the detergent tank and pour the detergent into tank HIGH PRESSURE HOSE STORAGE Once the high pressure hose is rolled hang it on the back of the machine using the hook and loop strap to secure in place ON OFF SWITCH This switch turns the pressure washer on and off GUN The pressure washer gun has a gripping surface that provides added control of the lance and helps reduce fatigue TRIGGER WITH LOCK OUT The trigger lock out prevents accidental use of the high pressure trigger ASSEMBLY UNPACKING This product requires assembly Carefully cut the box down the sides then remove the product and any accessories from the box WARNING This new product has been shipped in a partially assembled condition as described below If in doubt call Greenworks Tools Customer Service for assistance Operation of a product that may have been improperly preassembled could result in serious personal injury m Inspect the product carefully to make sure no breakage or damage occurred during shipping a Do not discard the packing material until you have carefully inspected and satisfactorily operated the product a f any parts are damaged or missing please call Greenworks Tools Customer Service for assistance A WARNING If any parts are damaged or missing do not operate this product until the parts are re
10. fety Children should be supervised to ensure that they do not play with the appliance EDEN GEDA EPDEDGNAOCDEDED ENGLISH Original Instructions Use correct product Don t force product or attachment to do a job it was not designed for Don t use it for a purpose not intended Use only recommended accessories The use of improper accessories may cause risk of injury Never leave product running unattended Turn power off Don t leave product until it comes to a complete stop Keep the motor free of grass leaves or grease to reduce the chance of a fire hazard Keep product dry clean and free from oil and grease Always use a clean cloth when cleaning Never use brake fluids gasoline petroleum based products or any solvents to clean product Check the work area before each use Remove all objects such as rocks broken glass nails wire or string which can be thrown or become entangled in the machine Do not use product if switch does not turn it off Have defective switches replaced by an authorized service centre Avoid dangerous environments Don t expose to rain Keep work area well lit Do not abuse the cord Never use the cord to carry the product or to disconnect the plug from an outlet Keep cord away from heat oil sharp edges or moving parts Replace damaged cords immediately Damaged cords increase the risk of electric shock Inspect extension cords periodically and replace if damaged Keep handle
11. greenworks TOOLS 120 Bar 340 L H ELECTRIC PRESSURE WASHER 51017 Ce o OPERATOR S MANUAL A Read all safety rules and instructions carefully before operating this tool EDEN GEDA EPDEDENAOCDEDED ENGLISH Original Instructions INTENDED USE The cleaner is intended only for the cleaning of vehicles boats buildings etc by the removal of stubborn dirt using clean water and chemical detergents For domestic use only not for professional use and only for operation at temperature above 0 C INTRODUCTION This product has many features for making its use more pleasant and enjoyable Safety performance and dependability have been given top priority in the design of this product making it easy to maintain and operate When using power tools basic safety precautions should always be taken to reduce the risk of fire electric shock and personal injury Also please read and heed the advice given in the additional safety instructions IMPORTANT SAFETY INSTRUCTIONS WARNING Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury Learn the machine s applications and limitations as well as the specified potential hazards related to this tool by studying this manual Followthe maintenance instructions specired in this manual Never operate the pressure washer with any guard or cover removed or damaged Do n
12. hands when the machine is on f je in fi Electric Shock Risk of Explosion Failure to use in dry conditions and to observe safe practices can result in electric shock Fuel and its vapours are explosive and can cause severe burns or death Risk of injury Do not connect to drinking water supply without backflow preventer Warning Never point the gun to human animals the machine body power supply or any electric appliances Appliance not suitable for connection to the drinking water mains without backflow preventer EDEN GEDA EDEDENAOCDEDEPD ENGLISH Original Instructions The following signal words and meanings are intended to explain the levels of risk associated with this product SYMBOL SIGNAL MEANING A DANGER Indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING iidieates a patentally hazardous situation which if not avoided could result in death or serious injury CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION Without Safety Alert Symbol Indicates a situation that may result in prop erty damage SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician For service we suggest you return the product to the nearest AUTHORIZE
13. his product should not be disposed with other household wastes throughout the EU To prevent possible harm to the environment or human health from uncontrolled waste disposal recycle it responsibly to promote the sustainable reuse of material resources To return your used device please use the return and collection systems or contact the retailer where the product was purchased They can take this product for environmental safe recycling LIMITED WARRANTY CEND LIMITED WARRANTY Warrants this outdoor product to be free of defects in material and workmanship for 24 months from the date of purchase by the original purchaser subject to the limitations below Please keep your invoice as proof of date of purchase This warranty is only applicable where the product is used for personal and non commercial purposes This warranty does not cover damage or liability caused by due to misuse abuse accidental or intentional acts by user improper handling unreasonable use negligence failure by end user to follow operating procedures outlined in the user s manual attempted repair by non qualified professional unauthorized repair modification or use of accessories and or attachments not specifically recommended by authorized party Please see your local dealer for list of authorized service centers in your area This warranty does not cover belts brushes bags bulbs or any part which ordinary wear and tear results in required replacement during
14. le to the lance m Turn on the water supply STORING THE PRESSURE WASHER Store in a dry covered frost free area where the weather can t damage it Always empty water from gun hose and pump NOTE The use of a pump protector is recommended to prevent cold weather damage during storage over the winter months Telescopic handle use See Figure 10 e Pull up and fully extend handle for use e For transporting pull as shown e To lower handle push handle until it lock into place for storage A IMPORTANT This handle is for pulling the unit Do not lift the unit by this handle ENGLISH Original Instructions Motor will not start On O ff switch is in the Turn switch to the ON OFF O position position Squeeze gun trigger Power cord is not plugged in Plug in power cord Defective extension cable Try without extension cable Electrical outlet does not supply Try a different outlet adequate power Unit does not reach Diameter of garden hose is Replace with a 1 25 mm or 5 8 high pressure too small 16 mm garden hose Water supply is restricted Check garden hose for kinks leaks and blockage Not enough water supply Open water source fully Water inlet filter is clogged Remove filter and rinse in warm water Power nozzle is in low Turn power nozzle to high pressure position pressure position Pump is sucking air Check that hoses and fittings are airtight Turn O
15. ly mains not public drinking water supply mains please observe the local regulations of local boards or local water supplier To ensure that there is no feedback of contaminant into the water supply the appliance must not be connected directly to the public drinking water supply mains If the appliance is connected to potable water mains backflow prevention devices should be incorporated in or fixed to the water supply system The installation should be accepted by local boards or water supplier and should be conducted by professional technical personnel The backflow prevention devices should be appropriate to fluid categories and comply with the requirement to avoid back siphonage according to EN 60335 2 79 2009 Before connecting the garden hose to the pressure washer m Run water through the hose for 120 seconds to clean any debris from the hose m Inspect the filter in the water intake m If the filter is damaged do not use the machine until the filter has been replaced m f the filter is dirty clean it before connecting the garden hose to the machine NOTE There must be a minimum of 3 metres of unrestricted hose between the pressure washer intake and the garden tap a With the garden tap turned completely off attach the end of the garden hose to the threaded tap connector OPERATION Applications This pressure washer can be used for the purposes listed below a Removing dirt and mould from decks cement patios
16. of the product Examine extension cord before using and replace if damaged Do not abuse extension cord and do not pull on any cord to disconnect Keep cord away from heat and sharp edges Always disconnect the extension cord from the receptacle before disconnecting the product from the extension cord Do not direct the jet against yourself or others in order to clean clothes or foot wear m Disconnect from the electrical power supply before carrying out user maintenance ma To ensure appliance safety use only original spare parts from the manufacturer or approved by the manufacturer m Do not use the appliance if a supply cord or important parts of the appliance are damaged e g safety devices high pressure hoses trigger gun WARNING Inadequate extension cords can be dangerous 0 WARNING A To reduce the risk of electrocution keep all connections dry and off the ground Do not touch plug with wet hands m To reduce the risk of injury High pressure cleaners shall not be used by children or untrained personnel keep children and visitors away All visitors should wear safety glasses and be kept a safe distance from work area This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their sa
17. ot operate the product while under the influence of drugs alcohol or any medication Do not wear loose clothing gloves neckties or jewellery They can get caught and draw you into moving parts Rubber gloves and non skid footwear are recommended when working outdoors Also wear protective hair covering to contain long hair Wear footwear that will protect your feet and improve your grip on slippery surfaces Always wear safety glasses with side shields Don t overreach or stand on unstable support Keep proper footing and balance at all times WARNING High pressure jets can be dangerous if subject to misuse The jet must not be directed at persons animals electrical devices or the machine itself WARNING This Appliance has been designed for use with the cleaning agent supplied or recommended by the manufacturer The use of other cleaning agents or 4 chemicals may adversely affect the safety of the appliance WARNING Don t use the appliance within range of persons unless they wear protective clothing m The electric supply connection shall be made by a qualified electrician and comply with IEC60364 1 o Only connect this machine only to a supply circuit protected by a residual current device RCD with a tripping current of not more than 30mA Use only extension cords that have watertight connections and are intended for outdoor use Use only extension cords having an electrical rating not less than the rating
18. placed Use of this product with damaged or missing parts could result in serious personal injury WARNING Do not attempt to modify this product or create accessories not recommended for use with this product Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury A WARNING Do not connect to power supply until assembly is complete Failure to comply could result in accidental starting and possible serious personal injury ASSEMBLING WAND TO WASHER GUN See Figure 3 Installing Wand to Pressure Washer Gun Insert the male baynet end 1 of the wand into the female bayonet outlet 3 firmly While pushing in the wand firmly turn clockwise 2 until tabs lock into place to ensure a leak free connection CONNECTING HIGH PRESSURE HOSE TO TRIGGER HANDLE See Figure 4 Connect the high pressure hose to the trigger handle CONNECTING THE WATER SUPPLY TO PRESSURE WASHER See Figure 5 The water supply must come from a water main NEVER use hot water or water from ponds lakes etc For ease of use a self coiling hose is provided EDEN GEDA PDEDOGNAOCDEDEPD ENGLISH Original Instructions NOTE When using the self coiling hose be sure that the hose does not become crimped during use as this may cause damage to the pump A Chun When connecting the appliance to the water supp
19. rer DEN MDOMMADENIODADED ENGLISH Original Instructions Some of the following symbols may be used on this product Please study them and learn their meaning Proper interpretation of these symbols will allow you to operate the product better and safer SYMBOL NAME DESIGNATION EXPLANATION A Safety Alert Indicates a potential personal injury hazard Volts Voltage A Amperes Current Hz Hertz Frequency cycles per second WwW Watt Power Minutes Time Alternating Current Type of current No Load Speed Class II Construction Rotational speed at no load Double insulated construction Per Minute Revolutions strokes surface speed orbits etc per minute Wet Conditions Alert Do not expose to rain or use in damp locations Read The Operator s Manual To reduce the risk of injury user must read and understand operator s manual before using this product Eye Protection Always wear safety goggles or safety glasses with side shields and as necessary a full face shield when operating this product 7A E sok Risk of Injection Kickback To reduce the risk of injection or injury never direct a water stream towards people or pets or place any body part in the stream Leaking hoses and fittings are also capable of causing injection injury Do not hold hoses or fittings To reduce the risk of injury from kickback hold the spray lance securely with both
20. ry High Pressure Washer Model 51017 See product rating label See product rating label Serial number Year of Construction is in conformity with the relevant provisions of the Machinery Directive is in conformity with the provisions of the following other EC Directives 2006 95 EC LVD Directive 2004 108 EC EMC Directive and 2000 14 EC Noise Directive incl modifications 2005 88 EC And furthermore we declare that the following parts clauses of European harmonised standards have been used EN 60335 2 79 2009 EN 60335 1 2002 A11 2004 A1 2004 A12 2006 A2 2006 A13 2008 A14 2010 15 2011 EN 62233 2008 EN 55014 1 2006 A1 2009 EN 55014 2 1997 A1 2001 A2 2008 EN 61000 3 2 2006 A1 2009 A2 2009 EN 61000 3 3 2008 the following parts clauses of other technical standards and specifications have been used EN ISO 3744 1995 Measured sound power level LWA 91 5 dB A Guaranteed sound power level 94 dB A Conformity assessment method to Annex V Directive 2000 14 EC Place date Changzhou 30 12 2011 Signature Gary Gao Naixin BEng CEng MIET Vice president of Engineering Gof 14
21. s dry clean and free from oil or grease Before starting any cleaning operation close doors and windows Clear the area to be cleaned of debris toys outdoor furniture or other objects that could create a hazard Do not use acids alkalines solvents flammable material bleaches or industrial grade solutions in this product These products can cause physical injuries to the operator and irreversible damage to the machine Keep the motor away from flammables and other hazardous materials Check bolts and nuts for looseness before each use A loose bolt or nut may cause serious motor problems Before storing allow the motor to cool When servicing use only identical replacement parts Use of any other parts may create a hazard or cause product damage ONLY use cold water Make sure minimum clearance of 1 metre is maintained from combustible materials Connect pressure washer only to an individual branch circuit Hold the gun and lance securely with both hands Expect the gun to move when the trigger is pulled due to reaction forces Failure to do so could cause loss of control and injury to yourself and others Save these instructions Refer to them frequently and use them to instruct other users If you lend someone this product lend them these instructions also WARNING High pressure hoses fittings and couplings are important for the safety of the appliance Use only hoses fittings and couplings recommended by the manufactu
22. ure To disconnect a nozzle from the lance once the cleaning job is complete m Turn off the pressure washer and shut off the water supply Pull trigger to release water pressure m Engage the lock out on the gun by pushing down on the lock out until it clicks into the slot ma Remove the nozzle by placing hand over nozzle then pulling back the Quick Connect collar Place nozzle in the nozzle storage area OPERATING THE PRESSURE WASHER See Figure 7 To apply soap m Pour detergent in the detergent tank m Install the detergent bottle on the spray wand m Start the pressure washer and spray the detergent on a dry surface using long even overlapping strokes To prevent streaking do not allow detergent to dry on the surface To clean m Using the 25 nozzle spray away from the target surface for approximately 10 seconds to allow any remaining detergent to be flushed from the hose m Start at the top of the cleaning area and work down overlapping the strokes MAINTENANCE WARNING When servicing use only identical replacement parts Use of any other parts may create a hazard or cause product damage WARNING Before inspecting cleaning or servicing the machine shut off motor wait for all moving parts to stop and disconnect plug from power source Failure to follow these instructions can result in serious personal injury or property damage A GENERAL MAINT
23. when servicing ELECTRICAL CONNECTION This product has a precision built electric motor It should be connected to a power supply that is 220 240 volts 50 Hz AC only normal household current Do not operate this product on direct current DC A substantial voltage drop will cause a loss of power and the motor will overheat If the product does not operate when plugged into an outlet double check the power supply EXTENSION CORDS See Figure 1 The cross section of any extension cables used must be proportional to their length i e the longer the extension cable the greater the cross section cables with a protection level of IPX5 must be used Use the chart to determine the minimum wire size required in an extension cord Ea Fig 1 Extension Extension Voltage cable up to cable up to Motor 25m 50m section section 220 240v 3x1 5mm 3x2 5mm EDEN GEDA EPDEDOENGOCDEDEPD ENGLISH Original Instructions WARNING keep the extension cord clesr of the working area Position the cord so that it will not get caught on lumber tools or other obstructions while you are working with a power tool Failure to do so can result in serious personal injury WARNING Check extension cords before each use If damaged replace immediately Never use the product with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury SPECIFICATIONS
Download Pdf Manuals
Related Search