COOKTOP IN SUPREME DESIGN
Contents
1. every 12 months that itis operating correctly and ifthere appears to be any abnormalities please contact the service call centre for advice For further details please refer to the warranty provided with appliance Regular care and maintenance ensures correct operation and high performance To maintain your hob in perfect condition clean it after every use removing any food spills ENVIRONMENTAL CONCERNS 22 Packing The packing material is 100 recyclable and is marked with the recycle symbol Ly The symbol X on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic equipment PRODUCT DESCRIPTION 3 3 O 1 Removable panstand grids Symbols 2 Semi rapid burner BR Shaded circle Tap closed 3 Semi rapid burner FL Large flame A Maximum opening delivery 4 Rapid burner Small flame A Minimum opening or reduced delivery 5 Auxiliary burner 6 Ultra Rapid burner 7 Control knobs The symbols 6 92 2 a are indicating which cooking field this knob activates Note your hob aesthetics can be slightly different from the drawing Burner placement and control symbols can vary PRACTICAL ADVICE FOR USING THE BURNERS This hob has burners of different diameters For better burner pe2. make sure the knobs are in off position and close the main gas supply cock or the gas cylinder valve Overheated oils and fats catch fire easily Always remain vigilant when cooking foods rich in fat oil or alcohol e g rum cognac wine Keep the packaging materials out of the reach of children Before cleaning or maintenance wait for hob to cool down Unattended cooking on a hob with fat or oil can be dangerous and may result in fire NEVER try to extinguish a fire with water but switch off the appliance and then cover flame e g with a lid or a fire blanket Danger of fire do not store items on the cooking surfaces Not for use in marine craft or caravans or mobile homes unless each burner is fitted with a flame safeguard Do not use or store flammable materials in the appliance storage drawer or near this appliance A WARNING Do not spray aerosols in the vicinity of this appliance while it is in operation AN WARNING Do not modify this appliance SAVE THESE INSTRUCTIONS INSTALLATION After unpacking the hob make sure that it has not been damaged during transport In the event of problems contact the dealer or your nearest After sales Service These instructions are only valid for the countries whose symbols is given on the data plate under the hob TECHNICAL INFORMATION FOR THE INSTALLER This product can be embedded in a worktop 20 to 50 mm thick If there is no oven beneath the hob insert a separator panel that ha
3. the data relevant to the voltage and power absorption are indicated on the rating plate ASSEMBLY Use protective gloves to clean the perimeter surface then apply the supplied gaskets to the hob as shown in the figure Be sure to apply both side gaskets 2 and main gasket 1 Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction NOTE the power supply cable must be long enough to permit its upward extraction To secure the hob use the brackets A provided with it Fit the brackets into the relevant bores shown by the arrow B and fasten them by means of their screws in accordance with the thickness of the worktop see the following figures Top 20 30 mm Top 31 50 mm A 0 07 OS LE ADJUSTMENT TO DIFFERENT TYPES OF GAS AN WARNING This operation must be performed by a qualified technician or authorised person If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob you need to call SERVICE and ask for the injectors change Remove the information label and keep it with the instructions booklet Ensure gas supply correspond with appliance design operating pressures suitable for the gas pressure indicated in the Instruction Ensure to rem
4. 8 45 5 The technical information are situated in the rating plate on the bottom side of the appliance Note A duplicate Data Plate provided with the appliances should be affixed adjacent to the appliance nearby on a cabinet or area where it is easily accessible for reference Before installing the hotplate consider the location of the gas supply and routing the gas line ELECTRICAL CONNECTION POINT POINT D GAS CONNECTION 307 112 52 CLEANING THE HOB PARTS Appendix A See drawing below for parts removal guides To reinstall the parts grids caps rings and burners reverse depicted operation E 5019 600 00913A
5. chain of ignition switches It is recommended to replace the valve gaskets each time the valve is replaced thus ensuring a perfect seal between the body and the gas train WARNING Do not modify this appliance REFERENCE TO LOCAL REGULATIONS Gas Safety Regulations The gas supply system must comply with local regulations to the current relevant gas standard AS NZS 5601 current edition AFTER SALES SERVICE Before calling the After Sales Service make sure you can give the following information 0000 000 00000 f faul blem ja as a the label affixed to the instruction warranty Il Il Il I Il service number that follows the word SERVICE on the rating plate under the hob and on the label affixed to instruction warranty your complete address and phone number If any repairs are required please contact an authorised After Sales Service as indicated in the warranty Apply the label from warranty here Manufacturer Whirlpool Europe S r l Viale G Borghi 27 21025 Comerio VA ITALY TROUBLESHOOTING GUIDE If the hob will not operate correctly before calling the After Sales Service refer to the Troubleshooting Guide to determine the problem 1 The burner fails to ignite or the flame is not even Check that The gas or electrical supplies are not shut off and especially that the gas supply tap is open The gas cylinder liquid gas is not empty The burner openings are not clogged The spark plug is not
6. is not aligned with the table The flame should be sufficient to allow flame to remain alight not be affected by draughts and keep safety device activated For LPG appliances remove the appliance regulator Regulating the minimum flow level of the gas taps Regulating the minimum flow level must be done with the tap at the lowest position small flame f There is no need to regulate the primary air in the burners To ensure the minimum level is properly regulated remove the control knob and adjust the screws found on the tap as follows see drawing 1 Tighten to reduce the height of the flame 2 Slacken to increase the height of the flame 3 With the burners on rotate the knobs from the maximum A to the minimum position f to check the stability of the flame Once you have finished regulating close up the seals again using sealing wax SERVICE INSTRUCTIONS Service and maintenance only to be carried out by an authorised person To replace parts such as burners valve and electric components the hotplate must be removed from the bench top by releasing the attachment hooks loosening the attachment screws of each burner unscrewing the hotplate attachments nuts which are visible at the bottom of the surface removing the hotplate top taking care to remove lid taps and screws under them and finally replacing the defective parts Note If the valves must be replaced first disassemble the
7. COOKTOP IN SUPREME DESIGN INSTRUCTION FOR USE BUILT IN GAS HOB INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY IMPORTANT This manual and the appliance itself provide important safety messages to be read and observed at all times This is the safety alert symbol pertaining to safety which alerts users to potential hazards to themselves and others All safety messages will follow the safety alert symbol and either the terms A DANGER Indicates a hazardous situation which if not avoided will cause serious injury A WARNING Indicates a hazardous situation which if not avoided could cause serious injury All Safety messages will tell you what the potential hazard is tell you how to reduce the chance of injury and tell you what can happen ifthe instructions are not followed The appliance must be disconnected from the power supply before carrying out any installation work Installation and maintenance must be carried out by a gualified technician or authorised person in compliance with the manufacturer s instructions and local safety regulations Do not repair or replace any part of the appliance unless specifically stated in the user manual If the information in this manual is not followed exactly a fire or explosion may result A WARNING causing property damage or injury Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance Wh
8. at to do if you smell gas Do not try to light any appliance Do not touch any electrical switch Do not use any phone in your building Immediately call your gas supplier from a neighbour s phone Follow the gas supplier s instructions If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supplier or authorised person Use appliance in well ventilated rooms only The electrical and gas connections must comply with local regulations When the hob is installed provide a multi pole circuit breaker with a contact separation of at least 3 mm that provides full disconnection Regulations require that the appliance is grounded The power cable must be long enough for connecting the appliance once fitted in its housing to the power supply Use only rigid piping for gas connection If necessary the electrical power cable must be replaced exclusively with a power cable having identical characteristics to the original supplied by manufacturer This operation must be performed by a qualified electrician The manufacturer cannot be held responsible for any injury to persons or animals or damage to property arising from failure to comply with these requirements Do not use multiple plug adapters or extension cords Do not pull the power cable to disconnect it from the electrical supply The electrical components must not be access
9. cidentally extinguished turn off the burner control and do not attempt to reignite it for at least one minute NOTE should particular local conditions of the delivered gas make the ignition of burner difficult itis advisable to repeat the operation with the knob turned to small flame setting The burner might go out when the knob is released This means that the safety device has not warmed up enough In this case repeat the operations described above DIMENSIONS AND DISTANCES TO BE MANTAINED mm NOTE if the distance A between the wall cabinets is between 600 mm and 730 mm the height B must be a minimum of 530 mm if the distance A between the wall cabinets is greater than the width of the hob the height B must be a minimum of 400 mm In case of installation of a hood above the hob please refer to the hood instructions fot the correct distance The indicated clearance dimensions are applicable to all non combustible materials Gas Type NATURAL 1 00 kPa test point pressure UNIVERSAL LP 2 75 kPa inlet pressure Burner Nominal Gas Nominal Injector Nominal Gas Nominal Injector Consumption MJ h Size mm Consumption MJ h Size mm Front RHS Auxiliary 3 7 0 87 3 8 0 56 Rear RHS Semi Rapid 6 6 1 17 7 0 0 75 Front LHS Semi Rapid 6 6 1 17 7 0 0 75 Rear LHS Rapid 10 7 1 50 11 7 0 96 Middle CHS Ultra Rapid 15 2 1 80 16 0 1 12 Total 42
10. dirty All the burner parts have been positioned correctly There are no draughts near the hob The burner parts have been cleaned dried and positioned correctly There is no liquid residuals in the burner area 2 The burner does not stay lit Check that When lighting the burner the knob has been pressed for enough time to activate the protection device The burner openings are not clogged near the thermocouple The end of the safety device is not dirty The minimum gas setting is correct see relevant paragraph 3 The pans or pots are not stable Check that The bottom of the container is perfectly flat The container is centered on the burner The grids have not been exchanged or positioned incorrectly If after the above checks the fault still occurs get in touch with the nearest After Sales Service Small scratches on iXelium grids could be noticed after usage due to friction with bottom of pots We recommend to place pot on the selected burner and avoid to slide pots on the grids themselves The presence of small stains on the bottom surface of the grids may be the cause of manual manufacturing process but do not compromise the quality of the product Clean iXelium grids following recommendation for iXelium material CLEANING THE HOB SURFACE AN WARNING Disconnect power before servicing All the enamelled and glass parts should be cleaned with warm water and neutral solution If you have a iX
11. elium hob observe the following cleaning recommendations Use a soft cloth microfibre is best with water or with everyday glass cleaning detergent Do not use paper kitchen towel which can leave traces of paper and streaks on the hob Donot use abrasive or corrosive products chlorine based cleaners or pan scourers Do not use steam cleaning appliances Donot use flammable products Do not leave acid or alkaline substances such as vinegar mustard salt sugar or lemon juice on the hob CLEANING THE HOB PARTS Grids burner caps and burners can be removed to be cleaned See APPENDIX A Clean them by hand with warm water and non abrasive detergent removing any food residues and checking that none of the burner openings is clogged Rinse and dry e Refit burners and burner caps correctly in the respective housings When replacing the grids make sure that the panstand area is aligned with the burner e Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order to ensure correct operation Check these items frequently and if necessary clean them with a damp cloth Any baked on food should be removed with a toothpick or needle NOTE to avoid damaging the electric ignition device do not use it when the burners are not in their housing MAINTENANCE SCHEDULE To ensure your appliance is always working correctly check all functions on the product periodically eg
12. f the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel pipe with fittings complying with local regulations 24 PRESSURE WARNING THIS PRODUCT IS NOT SUITABLE FOR A FLEXIBLE HOSE TEST POINT CONNECTION After connection to the gas supply check for leaks with soapy water Light up the burners and turn the knobs from max position A to minimum position to check flame stability As part of the installation procedure it is necessary for the installer to check pressure Ifthe pressure isn t correct it will affect the operation and 48 performance of the appliance i 5 N For LPG PROPANE models the gas supply for the hotplate must be regulated to et a pressure of 2 75kPa The gas inlet connection fitting is Y tapered B S P male thread in compliance with ISO 7 thread o iee For NG models the gas supply is connected to a regulator which is supplied The TEST POINT inlet connection has Y B S P male thread IT IS ESSENTIAL THAT THE ELBOW ON THE APPLIANCE BE HELD FIRMLY WITH A SPANNER DO NOT OVER TIGHTEN The regulated pressure for NG is 1 00kPa ELECTRICAL CONNECTION IN WARNING This operation must be performed by a qualified technician or authorised person The electrical connections must comply A WARNING with local regulations ww The earthing of this appliance is SAN compulsory by law Donotusean extension cord IMPORTANT
13. ible to the user after installation Do not touch the appliance with any wet part of the body and do not operate it when barefoot N WARNING AN WARNING This hob class 3 is designed solely for private household use for cooking food Do not use this appliance as a space heater to heat or warm the room Doing so may result in carbon monoxide poisoning and overheating of the hob The Manufacturer declines all responsibility for inappropriate use or incorrect setting of the controls The appliance and its accessible parts become hot during use Care should be taken to avoid touching heating elements Children less than 8 years of age shall be kept away unless continuously supervised This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved They shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision The use of a gas appliance produces heat and humidity in the room Make sure the room is well ventilated or install an extractor hood with exhaust duct Domestic animals should be kept away from the appliance In case of prolonged use additional ventilation may be necessary by opening a window or increasing the hood extraction speed After use
14. ove the natural gas regulator device and replace with the propane Ipg test point adaptor The gas nozzles must be changed by After Sales Service or a qualified technician or authorised person Nozzles not supplied with the appliance must be ordered from After Sales Service Adjust the minimum setting of the taps needs to be done by SERVICE after injectors change NOTE use pressure regulators suitable for the gas pressure indicated in the Instructions NOTE when liquid petroleum gas is used G31 2 75 kPa the minimum gas setting screw must be tightened as far as it will go or until the flame is small and stable enough to keep it alive IMPORTANT should you experience difficulty in turning the burners knobs please contact the After Sales Service for the replacement of the burner tap if found to be faulty It is best to change the injectors before starting installation Steps for injector exchange are 1 Remove the grids and burner rings caps and knobs see APPENDIX A 2 Remove the holding screws that fix the burner to the top cover Use gloves to lift up the cover Once you have removed the top cover you can access the burner injector 3 Remove the injector F using a 7mm side spanner Install new injector according to the table 4 Slacken the holding screw H to regulate the position X 15mm of the gas inlet coupling G with regard to the injector This needs to be done only if coupling G was moved or dimension X
15. rformance Burner Pot please stick to the following rules Use pots and pans with bottoms the same width as that of the burners or Ultra rapid From 24 to 26 cm slightly larger see table on the right Rapid From 24 to 26 cm Only use flat bottomed pots and pans Semi rapid From 16 to 24 cm Use the correct amount of water for cooking foods and keep the pot a covered Auxiliary From 8 to 14 cm Make sure pots on the grates do not protrude beyond the edge of the hob IMPORTANT improper use of the grids can result in damage to the hob do not position the grids upside down or slide them across the hob HOW TO USE THE HOB AN WARNING Do not let the burner flame extend beyond the edge of the pan IMPORTANT WHEN THE HOB IS IN USE THE ENTIRE HOB AREA MAY BECOME HOT To ignite one of the burners turn the relative knob anti clockwise to the maximum flame setting Press the knob against the control panel to ignite the burner After the burner has ignited keep the knob pressed for about 5 10 seconds to allow proper device operation This burner safety device shuts off the gas supply to the burner if the flame goes out accidentally because of sudden draught an interruption in the gas delivery boiling over of liquids etc The knob must not be pressed for more than 15 sec If after that time has elapsed the burner does not remain lit wait at least one minute before trying to light it again In the event of the burners flames being ac
16. s a surface at least equal to the opening in the work surface This panel that has to close completely the cutout in order to avoid any contact with the bottom part of the hob must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but in no case less than 20 mm from the bottom of the hob In the case that you intend to install an oven beneath the hob make sure that it is manufactured by Whirlpool and equipped with a cooling system The manufacturer declines all liability if another brand oven is installed beneath the hob Before installation make sure that the local gas delivery conditions nature and pressure are compatible with the settings of the hob see the rating plate and injector table the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations this appliance is not connected to a fume exhaust device It shall be installed in accordance with current installation regulations Particular attention shall be given to the relevant requirements regarding ventilation combustion products are discharged outdoors through specific hoods or wall and or window mounted electrical fans GAS CONNECTION WARNING This operation must be performed by a qualified technician or authorised person The gas supply system must comply with local regulations to the a current relevant gas standard AS NZS 5601 current edition The connection o
Download Pdf Manuals
Related Search