user manual (srm-6113)
Contents
1. SER MANUAL SRM 6113 Page 12 of 18 INTRODUCTION Thanks for your purchase of our product SRM 6113 High Power LED Moving Head It can works under auto mode sound and Master Slave mode with 16 built in programs The product has a long lifespan and 10W 4IN1 cree LED It is exquisite and applicable for all kinds of entertaining occasions Before you begin please read instructions carefully If you meet with any problem please contact with your distributor nearby MAIN FEATURES gDMX 512 control 12 channels mDMX AUTO SOUND Master Slave mode sRGBW control with 255 grades aRGBW total dimmer is 0 100 ma Shutter speed is 10 sec 1 10secs g9X10W 4IN1 RGBW LED mPAN scan angle 0 540 degrees m Tilt scan angle 0 230 degrees UNPACKING SRM 6113 High Power LED Moving Head USER MANUAL TENICAL SPECIFICATION TYpe SRM 6113 High Power LED MOVING HEAD Light Source 9X10W 4IN1 RGBW CREE LED Voltage 96 240VAC 50 60Hz POWEr 110W DimMmenSiOn 250X300X390MM W2. end it may be the problem of connection Find qualified professors to repair Check repair or change the data line Ensure connection is well and the first lamp s single input is connected with the controller output False or incomplete data connection False address setting Check DMX address Pull out the signal output and input of one fixture Then connect both directly If it works well this fixture is proved to be the failed one Handle the rest fixtures alike to check which fixture has problems If Reset normally but console Problem of signal Abnormally orno connector of some fixtures response es any problem please connect the technician Signal output does not match with the pin pins2 Toggle the PHASE button on the controller to and pins3 has a wrong reverse the polarity sequence 2 CLEANING Though increasing reliability by designing well and we never stop to improve quality to lengthen lamp s lifespan It is still indispensable to maintain it well by certain time in order to ensure best performance First clean fan and vent Favorable heat dissipation and ventilation is vital to lamp s normal work So clean the fan and vent during a certain time to guarantee smooth of wind path Otherwise dust will barrier vent which will affect the performance because of over heat after working for some time Second lens cleaning and maintenance To ensure the best effect of lamp please clean e
3. CH11 PAN FINE ALL Check all LEDs with motors PAN Check pan channels Display Pan TILT Check TILT channels Display TITL D Check red channels Display rEd GREN Check green channels Display GrEn BLUE Check blue channels Display bLuE N op m lt E m Page 15 of 18 WHITE Check white channels Display AnbE 8 DSPL STND Display bites normally Display bytes upside down REST REST on System Reset ell eee PAN TILT is 16 bit CH10 PAN FINE CH11 TILT FINE N PAN TILT is 8 bit CH10 CH11 does not exist 3 ABOUT EACH CHANNEL Green 0 100 white 0 100 paN oo T27 Medium OOO rmos iee Bottommost 000 255 Motor Speed CH10 000 255 PAN FINE 2 4 CH11 000 255 TILT FINE 2 4 000 024 RGBW Manual mode the relevant channels CH1 CH6 025 049 Built in program 1 the relevant channels CH2 050 074 Built in program 2 the relevant channels CH2 CH12 200 224 Built in program 8 the relevant channels CH2 225 244 Sound active program 245 255 20 seconds later system Reset Notes When 16 BT is on CH10 CH11 exists otherwise they do not exist MAINTENANCE 1 TROUBLESHOOTING Probable cause s Suggested remedy Fixtures do not No power source Check if power source is on or cord works well Page 16 of 18 Cut off power source and change the same type Fuse burnt fuse If fuse was burnt on
4. eight 6 45KG SAFETY WARNING For your convenient and accurate operation please read following information carefully Suitable for indoor use only Put it in a dry well ventilated place in case of short cut caused by erosion of moisture and rain Do not install it nearby hot sources in case that rising temperature of lamp damages itself Do not barrier vent in order to ventilate well and dissipate in time Connect the fixture with power source which has a ground line and voltage of power source should accord with rating voltage Page 13 of 18 If fuse was damaged change the same type You can only choose accessories the manufacturer provides when need repairing Ambient temperature of the lamp should not exceed 40 C If any problem contact with professional technicians working in our after sales service department PANEL REVIEW Fun Down Up FUN function menu or withdraw the last menu ENTER enter the next menu or definite present value UP increase one step each time DOWN decrease one step each time INSTALLATION AND SETTING 1 MULTI FIXTURES CONNECTION Controller The shield connection is pin 1 while pin 2 is Data Negative S and pin 3 is Data positive S Page 14 of 18 fy Pint Gnd Pin2 Dmx Pin3 Dmx 2 LAMP BODY INSTALLATION Notes Do n
5. ot install it nearby the curtain or flammable materials Only for indoor use OPERATION 1 SET DIPSWITCHES mEach fixture occupies 12 DMX channels gDMX 512 signals can control multi fixtures together however you must set DMX address of each lamp first Different DMX address will lead to different movements m You can set DMX address from 1 500 on the multi function display panel mSwitch on power supply and after finishing resetting the panel will show 001 that is to say DMX address is 001 and the first lamp has been controlled by 1 12 channels In turn the second fixture has been controlled by 13 24 channels When panel shows 001 press UP DOWN button until it shows 013 Then just press ENTER button In the same way the third fixture has been controlled by 25 36 channels and the panel shows 025 m Through this method you can control multi fixtures to perform different movements 2 CHANNEL FUNTIONS DISPLAY FUNCTION 001 501 503 DMX address 16BT is on the max value is 501 M DM DMX mode M AU AUTO mode M SO SOUND mode 8 built in programs PR 1 PR 8 Pr1 4 means skip Pr5 8 means fade SP01 SP15 Auto speed is 0 1 20 seconds each step STND Run clockwise as DMX value increases gt A m Bas Run anticlockwise as DMX value decreases STND Run clockwise as DMX data increase V Run anticlockwise as DMX data decreases STND CH7 PAN CH8 TILE CH10 PAN FINE CH11 TILT FINE EV CH7 TILE CH8 PAN CH10 TILT FINE
6. very lean or reflective setting Use the soft cotton with some lotion to clean it but do not damage lens Third check line during a certain time Check connecting line wiring and ground line to ensure safety of using lamp during a certain time Forth mechanical transmission part maintenance Check mechanical transmission part if it has any loose part during a certain time such as a strap Abrasion of mechanical transmission part will affect stability of lamp work If strap is loose you should change it if needed Page 17 of 18
Download Pdf Manuals
Related Search