Dvr4mqae GB
Contents
1. DVR4MQAE DIGITAL 4 CHANNEL MULTIPLEXER QUAD MPEG 4 RECORDER ETHERNET a cllemen components 1 Introduction To all residents of the European Union Important environmental information about this product This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm X the environment Do not dispose of the unit or batteries as unsorted municipal waste it should be taken to a specialised company for recycling This device should be returned to your distributor or to a local recycling service Respect the local environmental rules If in doubt contact your local waste disposal authorities Thank you for buying the DVR4MQAE Please read the manual thoroughly before bringing this device into service If the device was damaged in transit don t install or use it and contact your dealer Contents 1 digital video recorder 1 power adapter software accessories HDD key and this manual 2 Safety Instructions Be very careful during the installation touching live wires can cause life threatening electroshocks Keep this device away from rain and moisture S p y AN Be aware of the presence of uninsulated dangerous voltage Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems 3 Features e General o MPEG4 real time compression format o hig2. Digital Device Control Panel 4CH DVR a0 0 oD3R3 TATA a b cde fgh i Image Transfer Rate Per Second Data Transfer Rate Connect Disconnect Resolution NTSC 320 x 228 IE 640 x 456 PAL 320 x 276 El 640 x 552 Image Quality High Medium Low Snapshot press this button to have a snapshot of the image which will be saved in the designated destination Record press this button The video web server will start to record Press this button again to stop the recording The recorded files will be saved onto the PC Each recorded file can contain up to 18 000 frames When the recorded file capacity is full the new recorded file will be saved to the second file If the HDD space is less than 200MB the program will stop recording System Config press this button to enter the setting page of the video web server Number of Online Users CH1 4 4 channel Display Search Record Stop Fast Rewind Fast Forward Pause Slow Playback Play DVR4MQAE 22 VELLEMAN p q Digital Zoom r Set press this button to change channel display position Press A Y lt gt to select the channel you would like to change Press or to select the channel you would like to show Press Enter button to confirm s Sequence press this button to enter the call monitor function and press again to exit from call monitor mode t Enter u PTZ Control Off On
3. 14 Appendix 3 Recording Time Table 1 Take the NTSC system and outdoor environment as an example 2 Recording time varies depending on the following factors Different camera quality Different picture composition such as frequency of the object movement i 500GB Recordin Record Mode Quality IPS Time Hour g Days 30 436 9 18 2 Ae 15 767 6 32 0 7 1398 0 58 2 3 2958 6 94 1 30 552 8 23 0 High 15 971 3 40 5 7 1768 9 73 7 3 2857 9 119 1 Frame 30 726 2 30 3 15 1276 0 53 2 Monig 7 2323 9 96 8 3 3754 5 156 4 30 1173 7 48 9 15 2062 2 85 9 Basi 7 3755 9 156 5 3 6068 1 525 8 120 520 8 21 7 60 915 1 38 1 Bpel 30 1666 7 69 4 15 2692 7 112 2 120 734 2 30 6 60 1290 0 53 8 oF nga 30 2349 5 97 9 15 3795 9 158 2 120 966 2 40 3 enil 60 1697 6 70 7 30 3091 8 128 8 15 4995 2 208 1 DVR4MQAE 37 VELLEMAN 120 1338 7 55 8 60 2352 1 98 0 Banig 30 4283 8 178 5 15 6921 0 288 4 15 Appendix 4 Compatible USB Brands Upgrade the firmware of the DVR to the latest version to ensure the accuracy of following table Manufacturer Model Capacity Transcend JetFlash 110 256MB Transcend JetFlash 110 512MB Kingston DataTraveler DTI KUSBDTI 256FE 256MB Kingston DataTraveler DTI KUSBDTI 256FE 512MB PQI Cool Drive U339 256MB PQI Cool Driv
4. HIGH E bos SUPERVISOR INFINITY A Control only a b c d and e functions but a i a EDIT cannot control f function aeen Lid NORMAL gt mn Control only a g and e functions but cannot control b c and P functions GUEST Watch the image only Only the a function can be used 3 Life time According to different authority level different Ms ariel accounts can stay online for different time period DY SUPERVISOR SUPERVISOR INFINITY 1min 5min 10min 1hour 1day infinity Network Backup 2j nsh Lin Max Urh 5 AOD PECETE EDT Exit ox Alem List Gerena Uanmane iigh Life time 1 by F Online User Into Q tal at Passwoo p User bevel iio DVR4MQAE 31 VELLEMAN ONLINE USER INFO Get all the online users information here Name IP Address Authority Level Resolution and Image Quality FILE PATH 1 Snapshot Path Assign the route for saving the snapshot picture 2 Record Path Assign the route for saving the manual recording file 3 Alarm Audio Path The default alarm audio sound is alarm wav You can have your own alarm sound file by entering the file path Motity E Document and Settagzcatherme ke Deiktopi Recond Path Moniy e Documents and Setiughcathenae lee Deckiop Alarm Aadio Path g AP Connection Via AP Browser The DVR can be viewed over the network wi
5. o optional Independent Disk Array IDA VGA connector Velleman cartridge DVR CARTR1 Technical Specifications video system NTSC PAL switchable video compression format MPEG 4 video input 4 channels composite video signal 1Vpp 75 ohms BNC video loop out 4 channels composite video signal 1Vpp 75 ohms BNC video output o main monitor output composite video signal 1Vpp 75 ohms BNC o Call monitor output composite video signal 1Vpp 75 ohms BNC maximum recording resolution o frame 720 x 480 pixels 30 IPS NTSC or 720 x 576 pixels 25 IPS PAL o CIF 352 x 240 pixels 120 IPS NTSC or 352 x 288 pixels 100 IPS PAL adjustable recording speed o frame 30 15 7 3 IPS NTSC or 25 12 6 3 IPS PAL o CIF 120 60 30 15 IPS NTSC or 100 50 25 12 IPS PAL image quality setting best high normal and basic hard disk storage IDE type ATA66 supported HDD x 1 support each HDD capacity over 400GB HDD Quick Cleaning quickly clean up the index system of the recorded files 250GB under 2 secs recording mode manual timer motion alarm refresh rate 120 IPS for NTSC and 100 IPS for PAL multiplex operation pentaplex functions live display record playback backup and network audio I O 4 audio inputs 2 audio outputs mono motion detection area 16 x 12 grid per camera for all channels motion detection sensitivity 4 adjustable with precise calculation for motion detection pre alarm recording
6. to confirm the Press 8 or to choose the Press 4 or to choose the height start area width of the area of the area and press ENTER again to confirm F Multi detected area Press to turn all area Press to turn all area not under detection to be detected AY lt P navigates between targets 4 LS The sensitivity of comparing two different images The smaller the value the higher sensitivity for motion detection The highest sensitivity setting is 00 the lowest sensitivity setting is 15 The default value is 07 5 SS The sensitivity towards the size of the triggered object on the screen the number of motion detection grids The smaller the value the higher the sensitivity for motion detection The highest sensitivity setting is 00 and the lowest sensitivity setting is 15 The default setting is 03 NOTE The default setting of Spatial Sensitivity is 03 This means that when 3 grids are detected for motion at one time the system will get triggered The value of Spatial Sensitivity must be less than the number of grids which you set up to motion detection area 6 TS The sensitivity towards how long the object gets triggered The smaller the value the higher sensitivity for motion detection The highest sensitivity setting is 00 while the lowest sensitivity setting is 15 The default setting is 02 7 RE The value of RE is a reference for detection The default value is 10 which means the
7. yes 8MB backup device USB 1 1 backup and network remote recording backup web transmitting compression format Motion JPEG Ethernet 10 100 Base T supports remote control and LiveView via Ethernet mobile surveillance support GPRS to access the system via mobile phone requires J2ME MIDP2 0 protocol web interface supports USB 1 1 ports 1 on front panel and 1 on back panel remote control DVR and PTZ via IR transmitter RS485 PTZ control supports PELCO D protocol dwell time programmable and adjustable alarm I O 4 inputs 1 output picture zoom supports 2x digital zoom key lock yes system recovery system auto recovery after power reconnected video loss detection yes camera title supports up to 6 characters video adjustments hue colour contrast brightness date display format YY MM DD DD MM YY MM DD YY and OFF power supply 19VDC incl power consumption 42W operating temp 10 C 40 C dimensions 343 x 223 x 59mm DVR4MQAE 2 VELLEMAN 5 Description a Front Panel 1 HDD Cartridge Lock Lock or unlock the cartridge of the HDD 2 USB Supports firmware update and files backup 3 LED Light HDD HDD is reading and recording HDD Full HDD is full ALARM The alarm is triggered TIMER Timer recording is activated PLAY Playing REC Recording 4 MENU Press this button to enter the main menu and enter the default password 0000 Press ENTER to confirm your password 5 ENTER SET
8. you will receive a confirmation email within a few minutes To complete registration follow the instructions received Complete these steps within 48 hours to complete the registration If the confirmation email was not received within an hour request a password reset http Awww dyndns org account resetpass e Use the DDNS username and password to login the DynDNS e Create Hostname Login Account My Service Add Host Services Add Dynamic DNS Host Enter and choose the hostname Click on Add Host DDNS Hostname created i wes Ma moft Lamet Explower WO SAD ANAW IRT szp RAD i N O33 Qro unnat Gur meo fa e Neee brdn piorar ehoas Nod DynDNS About My Accourt DVR4MQAE Add Host Services eva nue re gt New Dynamic DNS Host aif 34 98 44 z CUR Wa Gudi vr posd is nee Viuha 1 Seres Accourt Support Mews 4 Havane YourHo chame IP Address Rit Enable Wildcard F Mall Exchanger opca 7584 26 Add Host Py Reset Form VELLEMAN MAIL Press the ea button to enter the system setting page 1 When alarm or motion alarm is triggered a video copy file can be captured The DVR can send an email notification to the assigned recipients up to 5 recipients NOTE To activate the email notification function enable the function of the email notification in the Alarm setting first
9. 2 10 Window 12 2 10 10 DVR4MQAE 6 VELLEMAN Note 1 The real appropriate setting value will depend on the real situation such as the angle of the lens the distance between the camera and object etc Note 2 Refer to 9 g Advance Menu_Detection for detail setting b Network Backup You can easily use the licensed software AP to backup the recorded files to PC and playback the backup videos For detailed operation refer to 10 f Licensed Software AP Start Backup Tune 200s 712727 fos 10 00 ana Backup lnformabon BakupSee 5 MB Chansa p HDDNum MASTER x File Path CWocuments aad Seinge seat 8 Operation a Recording The DVR offers three recording modes manual record event recording and timer record If power is off accidentally recorded video files will still be stored in the HDDs The DVR will return to the original recording status after the power has been restored 1 MANUAL RECORDING continuous recording Recording is initiated by manually pressing the REC button indicated by e 2 EVENT RECORDING triggered by motion or external alarm When this function is activated the recording is triggered by motion or external alarm and indicated by and W 3 TIMER RECORDING scheduled time Recording is scheduled by the timer and is indicated by TIMER RECORD Under Recording NOTE When the HDDs are full under O W recording mode previous reco
10. 456 PTZ Change Image Quality L al ixi 3 deo Web Serres gt SZD WD MEAD ADARA IAD NAG gt i 032 Qro uanet Gee j UHM JA ntvl z pua wu Aage D A Same as the AP operation Refer to 40 4 Licensed Software AP To set the display position of the image LT Upper Left LD Lower Left RT Upper Right Lower Right h GPRS depending on your mobile phone type GPRS function Installation and Viewing Take Motorola 768i as an example 1 Your mobile service provider must have GPRS service and the phone handset needs to support GPRS and Java MIDP 2 0 to run the application 2 Connect to the website http 211 22 74 18 via the web browser of your cell phone make sure that your GPRS function is working Download and install 4CH_MPEG 4 4 After installation the 4CH_MPEG 4 icon will appear on the desktop of the phone 5 Click the icon of the 4CH_MPEG 4 video server to enter the setting frame Type in IP address port username and password of the DVR Press the Connect button 6 After having connected to the 4CH_MPEG 4 video server you will see AP interface shown on the screen and will see Online on title 7 Wait 3 minutes for the video signal to appear 8 After video signal is shown you can monitor and control your security system any time and anywhere NOTE It s not suggested to set the DVR port as 80 port because some telecommunication service pr
11. 7200 rpm Western Digital CaviarSE WD2500JB 250GB 7200 rpm VELLEMAN cannot be held responsible in the event of damage to or loss of programmes data or removable media VELLEMAN advises you to regularly make backups onto different storage media disc CD ROM etc of your documents data files or software installed onto our product The information in this manual is subject to change without prior notice DVR4MQAE 38 VELLEMAN
12. Appendix 1 for HDD installation instructions NOTE Please refer to Appendix 2 for pin configurations of the external I O port DVR4MQAE 4 VELLEMAN k Speaker Camera 1 Camera 4 Call Monitor Main Monitor Audio in Jets en CE o jo oz IDA 4 Extend recording time with Alarm LCD Monitor more IDA connected Sensor Adapter Getting Started Before using the DVR have the HDDs installed refer to Appendix 1 for the installation of the HDDs Connect the AC power cord to the power adapter and plug into an electrical outlet The standby LED light will turn to red Press the POWER button The power LED will be red It takes approximately 10 to 15 seconds to boot the system Hold the POWER button until the red POWER LED turns green After some time the green turns red again Before operating the DVR please set up the system time first for setting system time please refer to 9 d Date settings SYSTEM INIT 1234 OK AUDIO OK AUDIO M OK DETECTING MASTER HDD OK DETECTING SLAVE HDD FAIL VERSION 1039 09 H6 04 AA 08 SYSTEM NTSC 788 DVR4MQAE 5 VELLEMAN Available Capacity of System Time Internal HDDs 7 2005 Mce E a a had pe Under HDD Overwrite al M ode Channel Title NOTE When the message HDD not found shows up refer to appendix 1 It may result from an improper installation of the HDD 7 Advanced Functions Advanced Motion Detection Settin
13. No DYR Mal from tene tech com t Device User Detection Modify alarm email address esten le Network Backup Mail Account cabenne be ys com Online User Iago File Poth 4CH DVR ext veeeeeeee Detection Network Backup Online User Info File Path NTD Ais LEL MEETRM 110 12 Search Lat 3 Alum Abm Lat Geren Account Oni User Info Fue Path 4CH DVR ear TITLE BR CT ST HUE COV REC VELLEMAN DEVICE Press the ea button to enter the system setting page 1 2 DETECTION Press the 1h button to enter the system setting page 1 2 ID No Protocol Type Alarm Motion Detection Area Select the desired channel of the installed external device Press Edit to enter the setting box Device Type Choose either general camera or PTZ camera 1 c anaes 1 NORMAL 2400 2 CAMERA NORMAL 2400 3 PTZ 3 P D 2400 4 PTZ NORMAL 2400 Choose the ID number from 0 to 255 of the installed external PTZ device Onki User Info Fie Path Choose NORMAL protocol for our own brand camera Choose P D PELCO D protocol for all VELLEMAN cameras Baud Rate Set the baud rate of each channel 2400 4800 9600 19200 38400 57600 115200 depending on the NO DEVICE ID PROTOCOL specifications of the dome camera 1 camera 1 NORMAL 2400 gt After setting press OK and then press APPLY to confirm Select the des
14. PTZ channel onto which the camera is connected When you turn the PTZ control on select the PTZ device and press OK button to enter the PTZ control AP screen press ESC to exit from PTZ control AP screen and back to DVR control AP screen SELECT NO PTZ cancer Esc v Menu Up Down Left Right w Turbo Off On Digital Device Control Panel PTZ amp Vinoeo WEB SERVER 60 121 46 236 aa Hoia E FR 2 54 fps DR 406 kbps HU admin DVR4MQAE 23 VELLEMAN Preset 1 16 AUTO E Zoom Tele Zoom Wide k Focus Near Focus Far Max Zoom In E Max Zoom Out Enter PTZ Control Off On When you turn the PTZ control on select the PTZ device and press Ok button to enter the PTZ control AP screen press ESC to exit from PTZ control AP screen and back to DVR control AP screen q Menu Up Down Left Right r Turbo ON OFF To speed up the menu selection or the control of the PTZ camera under video web server you can activate Turbo function by clicking this button You can change the turbo steps from 1 to 10 Example If you activate the TURBO function set the value of the turbo step as 3 when you press one of the button up down left right one mouse Click will function as if you click 3 times 8 Playback Operation see 10 f Network Backup or 10 e USB Backup AP Playback Window AP Config Setting Box Ta ea Aw me ca asnar
15. function on off WATERMARK This function stays always ON DVR4MQAE 14 VELLEMAN N w 9 Advance Menu ALERT EXT ALERT INT BUZZER KEY BUZZER VLOSS BUZZER Move the cursor to the ALERT and press MOTION BUZZER ENTER The screen will show the following ALARM BUZZER options HDD BUZZER HDD NEALY FULL GB ALARM DURATION SEC PRE ALARM EXT ALERT Set the sound on off when external alarm is triggered INT BUZZER Set the sound of KEY VLOSS MOTION ALARM HDD FULL on or off KEY BUZZER Set the sound on off VLOSS BUZZER Set the sound on off MOTION BUZZER Set the sound on off when motion alarm is triggered ALARM BUZZER Set the sound on off when internal alarm is triggered HDD BUZZER Set the sound on off when the HDD is full HDD NEARLYFULL GB If HDD buzzer is on you can choose to have a buzzer notification when the HDD available capacity has only xxx GB left ALARM DURATION SEC Press ENTER or or button to set the duration time of alarm recording 5 10 20 40 sec 10 PRE ALARM Set the pre alarm function on 8MB off When pre alarm and event record functions are activated the DVR will record 8MB file before alarm motion triggered Advance Menu REMOTE Move the cursor to REMOTE and press ENTER The screen will show the following options REMOTE DEVICE ID PROT
16. on CS DVR4MQAE 35 VELLEMAN e Step 1 Connect the connector with the HDD refer to Picture 1 e Step 2 Put HDD into the HDD cartridge Notice the bottom side is power side refer to picture 2 e Step 3 Screw the HDD to the cartridge Before doing this be aware that you must level pin 1 of the HDD at pin 1 mark because the screw hole differs from brand to brand refer to pictures 3 and 4 Precisely align the hard disk to the pin connection to ensure correct installation e Step 4 Reverse the HDD and put it into DVR refer to pictures 5 and 6 e Step 5 Connect the HDD with DVR refer to picture 7 el DE ae e e Step 6 Lock the cabinet by turning the key clockwise refer to picture 8 9 F unlocked NOTE If you do not lock the cabinet the DVR system will not function properly e Step 7 Close the cap refer to picture 9 13 Appendix 2 PIN Configuration PIN 1 RS232 TX DVR can be remotely controlled by an external device or control system such as a control keyboard using RS 232 serial communication signals PIN 2 RS232 RX COMPUTER DVR DVR can be remotely controlled by an external device or control system such as a control keyboard using RS 232 serial communication signals L F 4 PIN 3 PIN 5 ALARM INPUT When connecting the wire from the ALARM INPUT PIN 3 5 to GND PIN 9 connector the DVR will start recording and the buzzer will be on When the alar
17. osom A Playback Information Information display such as Date Time Resolution Rewind Forward Speed Status and Functions etc B Time Progress Bar Show the playback progress status C Functions De interlace Reduce the vibration of the paused picture De blocking Reduce the video mosaic phenomenon OSD Display the OSD of the AP playback window AVI convert Convert the entire recorded file to AVI One click to activate De interlace De blocking 08D ETT Avi convert Configuration setting PEITO watermark Open previous file Open next file To snap the video right click to make a starting format point red and click one more time to make an Config Setting Enter AP configuration setting box and ending point Then right click to convert to AVI set the file destination text colour and text colour of format progress status Watermark Proof of the authenticity of the backup video Open Previous File Open previous backup video Open Next File Open next backup video DVR4MQAE 24 VELLEMAN D Playback Control Buttons Play Stop Pause Fast Rewind Fast Forward E Snapshot Press this button to take a snapshot of the current image which will be saved in the designated destination F Close the Player NOTE e When pausing the playback picture press CEM button to go to the previous frame or press gt button to go to the next fra
18. the PTZ control mode DVR4MQAE 3 VELLEMAN b Back Panel 6060G06000L0 dP 0 o gt 0 r CEs mo B 1 1 75Q HI Switch to HI when using the LOOP function If not switch to 75Q 2 VIDEO INPUT LOOP Channel 1 4 INPUT Connect to a video source such as a camera LOOP Video output 3 MONITOR Connect to the main monitor 4 CALL MONITOR Connect to the call monitor Show the channel switch display When the alarm is triggered the call monitor will show the image of the triggered channel for a period of time 5 AUDIO IN 1 4 Connect to an audio source such as a camera with audio function When starting the recording function the audio input will be recorded 6 AUDIO OUT Connect to the monitor or the speaker with 2 mono audio outputs 7 D V PORT Connect to a VGA card 8 IR Not used 9 DISK ARRAY PORT Connect to the disk array for extended HDD capacity 10 EXTERNAL I O PORT Connect to an external device 11 LAN Connect to the internet by a LAN cable 12 LINK ACT LED Light When the internet is activated the LED will turn on 13 POWER Connect to the provided adapter 6 Installation and Connection a Connection Connect all the devices to set up a surveillance system as shown below 1 Install HDDs The HDDs must be installed before the DVR is turned on Connect cameras Connect monitors Connect the external devices Connect power o1 amp P NOTE Please refer to
19. 12 9 TIMER RECORD IPS Recording is activated by timer schedule Select the images per second of TIMER RECORD The options are as follows NTSC FRAME 30 15 7 3 PAL FRAME 25 12 6 3 CIF 120 60 30 15 CIF 100 50 25 12 10 TOTAL IPS SHARE There are two IPS settings FIX IPS per channel RECORD IPS 4 channels GROUP IPS per channel RECORD IPS number of channels under recording c Main Menu Options TIMER MENU RECORD Move the cursor to TIMER and press ENTER The screen will show the following options TIMER DATE ADVANCE DATE A scheduled record date SUN MON TUE WED THU FRI SAT MON FRI SAT SUN DAILY OFF can be set to activate the timer recording NOTE 1 Specific date can be changed with the or buttons NOTE 2 If you plan to set the timer recording across midnight there are two ways for setting the timer recording schedule Example 1 If you only want to set recording timer schedule from every Sunday 23 30 to Monday 23 30 then set the recording timer schedule as Sunday from 23 30 to 23 30 Example 2 If you plan to set the timer recording from Sunday 08 00 to Monday 15 00 then set the recording timer schedule as Sunday from 08 00 to 00 00 and Monday 00 00 to 15 00 2 START HH MM Select the starting time for the recording 3 END HH MM Select the finishing time for the recording DVR4MQAE 10 VELLEMAN d Main Menu Options DATE MENU RECORD Move th
20. DVR will compare 10 continuous images at one time according to the sensitivity of LS SS and TS simultaneously Therefore the bigger the value the higher sensitivity for motion detection 8 ALARM Select LOW HIGH for the alarm polarity The default alarm value is OFF 9 PRE NEXT Select PRE to go to the previous page Select NEXT to go the next page DVR4MQAE 13 VELLEMAN DETECTION TIMER Set DATE to ON Set the date start time end time of the detection function DETECTION TIMER DATE START END OFF 00 00 00 00 DAILY 08 00 18 00 SUN 06 00 23 00 MON FRI 00 00 00 00 h Advance Menu DISPLAY Move the cursor to the DISPLAY and press ENTER The screen will show the following options h N eo DISPLAY TITLE DISPLAY DATE DISPLAY HDD INFO LOSS SCREEN PLAYBACK INFO DWELL DURATION SEC DE INTERLACE WATERMARK TITLE DISPLAY Turn the channel title display on off DATE DISPLAY Turn the date display on off HDD INFO Turn the display information of internal HDD on off LOSS SCREEN Set the colour of video loss screen Blue or Black PLAYBACK INFO Set the position where playback information will be indicated centre or normal on the button of left hand side of the screen DWELL DURATION SEC Set the duration time of each channel for CALL MONITOR 2 4 8 16 sec DE INTERLACE Set the DE INTERLACE
21. Files Video Server E Video Player Locate the backup file on your memory stick or PC e g F CH04_01 787 Open the file and convert it Press PLAY to playback n Advance Menu HDD INFO You can get all the capacity information of the connected HDD HDD INFO HDD SIZE 400 517 400 517 400 517 NO HDD NO HDD NO HDD NO HDD o Advance Menu EVENT LOG You can get all the information event type time and channel of the event list including video loss list net list other lists such as power on off key unlock reset to default Select the event list you want to see and press ENTER EVENT LOG LIST LIST ALL DVR4MQAE 18 VELLEMAN 1 VLOSS LIST Show the information of video loss list 2 NET LIST Show the information of net login list 3 OTHERS Show the information of power on off unlock reset to default list 4 CLEAR ALL Clear all the event log lists 10 Additional Operation a Search Press SEARCH button on the front panel of the DVR to enter the search mode The screen will show the following options SEARCH MASTER LIST LIST LIST LIST LIST SEARCH 1 HDD Select the specific HDD 2 FULL LIST List all recorded files R RECORD S SYSTEM A ALARM MS MOTION T TIMER 3 RECORD LIST List of manual recorded files 4 SYSTEM LIST List of system recorded files Under continuous recording mode the DVR system will save one recording file every one hou
22. OCOL PTZ 001 P D CAMERA 002 NORMAL CAMERA 003 NORMAL CAMERA 004 NORMAL NEXT A N TITLE Title for each camera DEVICE Select to control normal camera or PTZ camera for each channel DVR4MQAE 15 VELLEMAN 3 ID Set the ID number 0 255 as the ID of each device 4 PROTOCOL Select NORMAL or PELCO D protocol The baud rate 2400 bits sec 5 RATE Set the baud rate of each channel 2400 4800 9600 19200 57600 PTZ Control 1 Device PTZ Pelco D protocol PTZ 2 Connection RS485 Refer to rear panel Refer to PIN configuration see Appendix 2 3 Detailed Instructions Refer to PTZ manual k Advance Menu SYSTEM Move the cursor to the SYSTEM and press ENTER The screen will show the following options SYSTEM SERIAL TYPE RS 485 BAUD RATE 02400 HOST ID 003 PASSWORD 0000 RESET DEFAULT RESET CLEAR HDD MASTER UPGRADE AUTO KEYLOCK LANGUAGE ENGLISH VERSION 1030 08 H3 04 V354 07 VIDEO FORMAT NTSC h SERIAL TYPE Press ENTER or or button to set the control serial type RS 485 RS 232 of DVR BAUD RATE Press ENTER or or button to set the BAUD RATE of DVR 2400 9600 19200 57600 3 HOST ID Press ENTER or or button to set the ID of DVR 0 255 4 PASSWORD Press ENTER or or button to set the password for accessing DVR 5 RESET DEFAULT Press ENTER a
23. Press ENTER to confirm Press SET to change the channel display position Press A WV lt P to select the channel you would like to change Press or to select the channel you would like to change Press ENTER to confirm Press MENU to quit 6 SEARCH Press this button to enter the search mode 7 SLOW Under playback mode press SLOW for a slow playback 8 ZOOM Enlarge the picture of the selected channel 2x digital zoom 9 HH Press HH to show the 4 channel display mode Press to change the setting in the menu 10 SEG Press SEQ to activate the call monitor function Press SEQ again to escape this mode Press to change the settings in the menu 11 POWER Turn the DVR4MQAE on or off with this button In the recording mode stop the recording before switching off the device 12 CH1 CH2 CH3 CH4 Press one of these buttons to select the channel 13 REC Activation of the manual recording 14 PLAY Playback of the last recorded files 15 4 Il V m 4 44 gt gt gt Press A VW lt gt to move the cursor up down left or right Under playback mode press Ill to pause the playback press m to stop the playback press lt lt to fast rewind and press gt to fast forward 16 AUDIO SLOW ZOOM Press these two buttons simultaneously to select live or playback sounds of the 4 audio channels Hold SLOW pressed and press ZOOM to select the channel 1 4 17 PTZ CONTROL Buttons Press these two buttons simultaneously to enter or exit
24. Upgrade You can use the USB to upgrade Format the USB memory device first 1 Get the upgraded files from your distributor 2 Save the upgraded files in your USB device do not change the file name 3 Go to the MAIN MENU SYSTEM UPGRADE and press ENTER 4 Select YES and press ENTER again to confirm upgrade 1 WARNING 2 WARNING 3 WARNING UPGRADE PLEASE WAIT PLEASE WAIT ARE YOU SURE UPGRADE KERNEL UPGRADE BOOT YES NO OK OK 4 WARNING 5 WARNING 6 WARNING PLEASE WAIT UPGRADE SUCCESS SHUTDOWN UPGRADE HTML REBOOT PLEASE WAIT OK OK OK DVR4MQAE 20 VELLEMAN NOTE 1 The USB format must be FAT 32 2 If the USB is not supported by the DVR then the USB ERROR message will be shown on the screen f Licensed Software AP SOFTWARE INSTALLATION 1 Put the CD into a driver It will start to install the application programme 2 The PC will auto run the setup file 3 After setup you will see e on the desktop SOFTWARE OPERATION Connect DVR with the PC via RJ45 network line 2 LAN Setting The default DVR IP is 192 168 1 10 and default username and password are both admin Set PC IP address as IP 192 168 1 XXX 1 255 except 10 in order to let the PC and DVR under the same domain NJ 3 Click amp twice to enter login page Key in 192 168 1 10 admin admin into the login page After connecting the DVR with loca
25. X speed playback press twice to get 1 8X speed three times to get 1 16X speed and four times to get 1 32X speed 6 AUDIO mauoa s Press sx 2u Simultaneously to select live or playback sounds of the 4 audio channels AUDIO 1 x AUDIO 2 x AUDIO 3 x AUDIO 4 L L L L AUDIO 1 P AUDIO 2 P AUDIO 3 P AUDIO 4 P Ne n n nn lt x 9 Detailed Menu Configuration a Menu Access Press MENU button to enter the main menu list The default password is 0000 Enter the default password and press ENTER you can alter the password later refer to 9 k Advance Menu_System Tip The default password is 0000 Press ENTER four times instead of using or to select 0 0 0 0 DVR4MQAE 8 VELLEMAN MENU There are 4 options available in the main menu RECORD RECORD Record mode setup TIMER TIMER Timer recording setup DATE DATE System date setup ADVANCE ADVANCE Advance functions setup Use the following buttons to set the menu A V lt gt to move the cursor to choose the numbers selections ENTER to go to the submenu to confirm the selection MENU to go to the menu OSD to confirm the change to exit the menu OSD b Main Menu Options RECORD MENU RECORD Move the cursor to RECORD and press ENTER The screen will show th
26. amera under video web server you can activate Turbo function by clicking this button You are allowed to change the turbo steps from 1 to 10 Example If the value of turbo step is 5 it means that when you press one of the buttons g n x REMOTE LOGIN aady 05 12 26 14 00 19 NO VIDEO LOSS up down left right one click is equal to clicking 5 REMOTE LOGIN andy 05 1226 1350 43 NO f REMOTE LOGIN REMOTE LOGIN andy 0512 26 1556 19 NO S HDO FULL times REMOTE LOGIN andy 05 1226 1339 20 NO PESA REMOTE LOGIN andy 05 12 26 08 57 45 NO 3 Max Log List REMOTE LOGIN andy 05 12 26 08 53 04 No KEY UNLOCK REMOTE LOGIN andy 05 12 26 08 52 26 NO RESET DEFAULT Set the maximum number of log list REMOTE LOGIN aedy 05 1226 08 50 21 NO F EMAIL FAILED REMOTE LOGIN andy 05 12 26 08 49 31 NO amp FIPFALED 4 Server Log REMOTE LOGIN andy 05 12 25 22 54 32 NO 6 amp 5 HOO ERROR REMOTE LOGIN tay 05 12 25 02 49 16 NO Press Server Log button to enter the server log list REMOTE LOGIN tay 05 12 25 09 45 27 No F HOD DMAERROR REMOTE LOGIN tay 05 12 25 09 42 59 NO window REMOTE LOGIN tay 05 12 25 08 30 44 NO ACCOUNT 1 Set up the user s account max 5 accounts password life time and authority level max 5 users on line at the same time a 2 User s level Han SUPERVISOR Control all the functions a b c d e and P wy SUPERVISOR INFINITY
27. e U339 512MB Apacer HANDY STENO HF202 256MB Apacer HANDY STENO HF202 512MB SanDisk Cruzer Micro Mini 128MB SanDisk Cruzer Micro Mini 256Mb SanDisk Cruzer Micro Mini 512Mb Dream Pocki Drive 256Mb 16 Appendix 5 Compatible USB Brands Upgrade the firmware of the DVR to the latest version to ensure the accuracy of following table Brand Model Capacity Rotation HITACHI Deskstar 180 GXP 120GB 7200 rpm HITACHI Deskstar 7K250 HDS722516VLAT20 160GB 7200 rpm HITACHI HDS722516VLAT80 160GB 7200 rom HITACHI HDS722516DLAT80 160GB 7200 rom HITACHI Deskstar 7K250 HDS722525VLAT80 250GB 7200 rpm IBM Deskstar 120GXP 80GB 80GB 7200 rpm IBM Deskstar 120GXP 80GB 120GB 7200 rpm Maxtor DiamondMax 536DX 60GB 4W060H4 60GB 7200 rom Maxtor DiamondMax Plus 9 80GB 5400 rom Maxtor DiamondMax Plus 9 Model 6Y120L 120GB 7200 rpm Maxtor DiamondMax Plus 9 Model 6Y 120L0 160GB 7200 rpm Maxtor MaxLine Plus Il Model 7Y250P0 250GB 7200 rpm Maxtor DiamondMax 10 160GB 7200 rpm Maxtor DiamondMax 10 200GB 7200 rpm Seagate Barracuda ATA IV ST380021A 80GB 7200 rom Seagate Barracuda ATA V ST3120023A 120GB 7200 rom Seagate Barracuda 7200 7 Plus ST3160023A 160GB 7200 rom Seagate Barracuda 7200 8 ST3200826A 200GB 7200 rom Seagate Barracuda 7200 8 ST3250826A 250GB 7200 rom Western Digital Caviar WD1200BB 00CAA1 120GB 7200 rpm Western Digital Caviar WD2000BB 0ODWAO 200GB
28. e cursor to the DATE and press ENTER The screen will show the following TIMER options DATE ADVANCE DATE DATE 2006 FEB 08 13 55 22 FORMAT Y M D DAYLIGHT SAVING ON 1 DATE Set the correct time of the DVR YEAR MONTH DAY HOUR MIN SEC 2 FORMAT There are three date formats Y M D M D Y D M Y 3 DAYLIGHT SAVING Position the cursor on DAYLIGHT SAVING and press ENTER to enter Now you can specify whether to use daylight saving time and time period ON OFF Daylight saving time can be adjusted manually Enter the daylight saving menu mode to set start time end time and to adjust the hour of the daylight saving DAYLIGHT SAVING ON 4th SUN MAR 01 00 00 OFF 4th SUN MAR 01 00 00 ADJUST 01 00 NOTE Press button to do the selections e Main Menu Options ADVANCE MENU RECORD Move the cursor to the ADVANCE and press ENTER The screen will show the following TIMER options DATE ADVANCE ADVANCE CAMERA DETECTION DISPLAY ALERT REMOTE SYSTEM NETWORK BACKUP HDD INFO EVENT LOG DVR4MQAE 11 VELLEMAN h Advance Menu CAMERA CAMERA CONT 128 TITLE Move the cursor to the title which you want to change and press ENTER to access the setting screen Assign a title to each channel up to six characters letters or symbols the default title is the channel number BRIG CONT SATU HUE Adju
29. e following TIMER options DATE ADVANCE RECORD MANUAL RECORD ENABLE EVENT RECORD ENABLE TIMER RECORD ENABLE OVERWRITE RECORD IMG SIZE RECORD QUALITY MANUAL RECORD IPS EVENT RECORD IPS TIMER RECORD IPS TOTAL IPS SHARE 1 MANUAL RECORD ENABLE Start stop the manual recording function 2 EVENT RECORD ENABLE Start stop the event recording function When this function is activated the recording will be triggered by motion or external alarm 3 TIMER RECORD ENABLE Start stop the timer recording function 4 OVERWRITE Select to overwrite the previous recording video in the HDD When the HDD is full under O W recording mode previous recorded files will be overwritten without further warning notices 5 RECORD IMG SIZE There are two recording options FRAME amp CIF When changing the recorded image size stop the recording first 6 RECORD QUALITY There are four quality settings BEST HIGH NORMAL amp BASIC DVR4MQAE 9 VELLEMAN 7 MANUAL RECORD IPS Recording is activated by pressing the REC button Select the images per second of MANUAL RECORD The options are as follows NTSC FRAME 30 15 7 3 PAL FRAME 25 12 6 3 CIF 120 60 30 15 CIF 100 50 25 12 8 EVENT RECORD IPS Recording is activated by event alarm and motion trigger Select the images per second of EVENT RECORD The options are as follows NTSC FRAME 30 15 7 3 PAL FRAME 25 12 6 3 CIF 120 60 30 15 CIF 100 50 25
30. g allows you to adjust different sensitivity factors based on a different e nvironment Quick Event Search allows you to examine the setting of motion detection factors In this way you can use specific motion detection setting to capture every important image a 1 Motion Detection Setting LS The sensitivity of comparing two different images The smaller the value the more sensitive the detection will become Application Environment vibration Light shift Shadow Mirror reflection SS The sensitivity towards the size of the triggered object on the screen The smaller the value the more sensitive the detection will become Application Different size of the object on the screen TS The sensitivity towards how long the object gets triggered The smaller the value the more sensitive the detection will become Application Different speed of the moving object RE The value of RE is a reference for detection The default value is 10 which means the DVR will compare 10 continuous images at one time according to the sensitivity of LS SS TS simultaneously Therefore the bigger the value the more sensitive the detection will become Application Slow and regular environment change Scenario Warehouse Different environments may require different settings The sample below is for reference only LS SS TS RE Entrance 10 2 2 10 Back Door 8 1 2 10 Pavement 5 2
31. h resolution recording Frame 720 x 480 pixels 30 IPS lt NTSC gt 720 x 576 pixels 25 IPS lt PAL gt CIF 352 x 240 pixels 120 IPS lt NTSC gt 352 x 288 pixels 100 IPS lt PAL gt 1 built in HDD base supporting 250GB more than 400GB with IDA recording audio with 4 channel input and 2 channel output image quality setting Best High Normal and Basic supports PELCO D protocol system auto recovery after power is reconnected peration Pentaplex functions live display record playback backup and network supports manual timer motion alarm remote recording functions possibility to cover the screen under recording watermark function ensures authentication of recorded images supports daylight saving function easy system upgrade via USB o easy file backup methods with USB and network remote recording backup e Event o advanced motion detection function and scheduled motion detection recording 4 different adjustable factors of motion detection sensitivity and convenient search function o alarm trigger recording will send alert with images to designated email and FTP address o supports pre alarm recording 8MB DVR4MQAE 1 VELLEMAN e 000000 QO00000 Network Viewing o remote surveillance on mobile phone via 3G amp GPRS or on PC through internet connection o web surveillance supports multiple viewers simultaneously up to 5 users External Device o extensive recording time by connected to Independent Disk Array
32. ier For detailed PPPoE setting refer to 10 f Licensed Software AP NOTE DHCP and PPPoE network types need to apply DDNS service to get Hostname to correspond to dynamic IP address For detailed DDNS setting refer to 10 f Licensed Software AP DDNS m Advance Menu BACKUP Move the cursor to the BACKUP and press ENTER The screen will show the following options BACKUP USB BACKUP Select USB BACKUP and press ENTER USB BACKUP START TIME 2005 10 27 11 25 46 END TIME 2005 10 27 11 50 58 AVAILABLE SIZE 0512 MB CHANNEL 05 HDD NUM MASTER BACKUP TO USB START 1 START TIME Select the start time of the backup 2 END TIME Select the end time of the backup DVR4MQAE 17 VELLEMAN 3 AVAILABLE SIZE The information of the available USB capacity 4 CHANNEL Choose the channel 5 HDD NUM Choose the HDD 6 BACKUP TO USB Press ENTER to backup the chosen file to USB NOTE The USB format must be FAT 32 If this is not the case first format to FAT 32 If the USB is not supported by the DVR the USB ERROR message will be shown on the screen We suggest clearing all the files in the USB before you backup files in your USB DVD R W or CD R W are optional refer to their manual The file type of the backup files only use the licensed software to view the playback IRON USB PLAYBACK WITH PC Open the programme Video Player C Program
33. ired channel and press Edit to enter the motion detection sensitivity and area setting oe Motion Detection Sensitivity Bena Enel Set the detection sensitivity in 4 different adjustable Edi factors No SET aRER Tae a3 WET TE LS The sensitivity of comparing two different ton ssa J 3 2 0 ow images The smaller the value the higher sensitivity for motion detection SS The sensitivity towards the size of the triggered object on the screen the number of motion detection grids The smaller the value the higher sensitivity for motion detection TS The sensitivity towards how long the object gets triggered The smaller the value the higher sensitivity for motion detection RE The value of RE is a reference for detection The bigger the value the higher sensitivity for motion detection amp Viveo Wee SERVER 1 168 1 10 Select LOW HIGH for the alarm polarity FR 6 50 fps DR 921 kbps HU admin Clicking the area with the mouse and choose the motion area to be detected The detection area is a transparent picture while the undetected area is in pink colour DVR4MQAE 28 VELLEMAN 5 Click the Select All to clean the previously selected detection area Click the Clear All to activate the detection area as full area After setting press OK and press APPLY to confirm NOTE Enable the motion detection function When the motion is triggered the icon will a
34. l LAN modify the network setting in the DVR or in the system configuration of the licensed software AP 4 Network Type Static IP Set the network information in the DVR menu see 9 1 Advance Menu_Network or in System Config of the licensed software AP see 9 m Advance Menu_Backup Network Type Dynamic IP DHCP and PPPoE Set the Network information in System Config of the licensed software AP For detailed DHCP and PPPoE setting please refer to 10 f DHCP and 10 f PPPoE o1 After setting up the network information click GS twice to enter login page Key in Username Password and IP Static IP or Host name Dynamic IP Click the green button to connect LOGIN AP Icon Explanation oD oo al Address Book press this button to add a new Search search the available DVR IP address IP into the IP Address Book or choose a preset in local area network and modify the network IP address to access the Video Server setting of the DVR 2 Player press this button to access and play the Copy press this button to copy all the recorded files saved in your PC software installation files so you can keep all the settings of video web server for next software installation on other PC NOTE The version of the licensed software will appear on the login page 7 Introduction of Basic Operation Video Web Server Control Panel DVR4MQAE 21 VELLEMAN
35. m input signal is Low the unit starts to record and buzz When Menu Camera Alarm is set to High the unit starts to record and buzz bos 12121212121 i ofokefoted PIN 7 EXTERNAL ALARM NC Under normal operation the COM connects with NC and disconneets from NO When the alarm is triggered COM disconnects from NC and connects with NO PIN 8 EXTERNAL ALARM NO Under normal operation the COM disconnects from NO When the alarm is triggered the COM connects with NO PIN 9 GND Signal GND PIN 10 RS485 B The DVR can be remotely controlled by an external device or control system such as a control keyboard using RS485 serial communication signals PIN 11 RS485 A The DVR can be remotely controlled by an external device or control system such as a control keyboard using RS485 serial communication signals DVR4MQAE 36 VELLEMAN PIN 12 13 PIN OFF PIN 14 ALARM RESET When connecting the wire from ALARM RESET PIN 14 to GND PIN 9 connector it can disable ALARM An external signal to ALARM RESET PIN 14 can be used to reset both ALARM OUTPUT signal and the DVR s internal buzzer When alarm has been triggered signal becomes Low and it will stop all alarm activities Under normal operation signal remains High PIN 15 EXTERNAL ALARM COM Under normal operation the COM disconnects from NO When the alarm is triggered the COM connects with NO PIN 16 17 GND Earth GND
36. me e Inthe playback mode of the software AP press button to check the authenticity of the BACKUP VIDEO If the BACKUP VIDEO has been altered the video image will turn to light red and the playback will be paused ADVANCED SETTING amp Vipco Wes Server P 192 168 1 10 ag Hic tis e Press the System Config k button to enter the system setting page NETWORK Server IP 192 168 1 10 Gateway 192 168 1 65 NetMask 950 252 350 0 The network configuration allows the DVR to connect to an Ethernet network or dial up Web Port jo z IP TYPE 1 Static IP 2 i Enter the server IP gateway net mask and web C DHCP port and press APPLY to confirm 2 PPPoE Enter the username and password provided by your ISP Internet Sever supplier and press APPLY to EXIT APPLY confirm E 2 6 T10 3 DHCP Device are 18 168 1 65 This DHCP function needs to be supported by router or pike SEF BE 22 cable modem network with DHCP service Choose the domt a ite DHCP IP type and press APPLY to confirm Fie Path C ner UserName edan C DEC Peceword CO NOTE PPPoE and DHCP network connection type will require applying DDNS service to get a Hostname to correspond to dynamic IP address Refer to 10 f DDNS for details ExT APPLY G ay 12 18 165 Net Mask 252 k 252 202 D NOTE Some routers may need to re
37. nd select YES to confirm or NO to cancel 6 CLEAR HDD Press ENTER and YES to clear HDD or NO to cancel In this function you can press or to select the MASTER HDD SLAVE HDD or DISK ARRAY which you plan to clear 7 UPGRADE Press ENTER and select YES to confirm upgrade or NO to cancel 8 AUTO KEYLOCK Set the auto key lock function Never 10 sec 30 sec 60 sec 9 LANGUAGE English only 10 VERSION The firmware version information will be shown on the screen 11 VIDEO FORMAT The information of the DVR s video format will be shown on the screen N DVR4MQAE 16 VELLEMAN Advance Menu NETWORK Move the cursor to the NETWORK and press ENTER The screen will show the following options NETWORK NETWORK TYPE DNS PORT NETWORK TYPE STATIC Select NETWORK TYPE and press or button to set the network type as STATIC Press ENTER to go to the submenu of the network In the submenu of network type use or button to set all the information needed in the DVR See below STATIC IP GATEWAY NETMASK 2 NETWORK TYPE DHCP This DHCP function needs to be supported by router or modem network cable with DHCP service For detailed DHCP setting refer to 10 f Licensed Software AP 3 NETWORK TYPE PPPoE This PPPoE function needs to have username and password from ISP suppl
38. on the screen Network Backup Search List Aha Durston 3 S amp C Alecm Last Geornal Acconat Alem Online User Indo Refresh File Path 4CH DVR NOTE Email Notification MJPEG pictures will be made at your designated space set in File Path plus an email containing the MJPEG pictures 1 10 pictures will be sent to the address which is set under Mail FTP Notification MJPEG pictures will be made at your designated space set in File Path plus an FTP file containing the MJPEG pictures 1 10 pictures will be sent to the address which is set under FTP ALARM LIST Press the 1h button to enter the system setting page 1 Itis a database which precisely lists all alarm triggered events with IP address of Video Web Server alarm triggered time and number of frames 2 You can play delete or clear all motion triggered 2j Gerenal Path recording events easily Osumin SAO 3 Click on the Refresh button to update the database Fil Path pe list 4 All the motion triggered files will be listed systematically for an easy search en ay DVR4MQAE 30 VELLEMAN GENERAL Press the ea button to enter the system setting page Network Backup 1 Get the information of DVR firmware version in this neh Mac eddmess 00005301464 window ng tice Lit MAX LOG List 0 2 Select Turbo Step 1 10 Aon s To speed up menu selection or the control of the PTZ File Path c
39. ovider may regulate 80 port i Optional Peripherals For the operation of the following peripherals please refer to their manual individually 1 IDA independent disk array 2 VGA connector DVR4MQAE 34 VELLEMAN 11 Troubleshooting PROBLEM SOLUTION No power Check the power cord Check the mains Check if the device is under KEY LOCK mode Press any key and key in the password to exit the Not working when pressing any button KEY LOCK mode No recorded video Check the connection TIMER RECORD is not working Check if the RECORD mode is enabled No live video Check the camera and monitor video cables and connections Check the power supply to the camera Check the setting of the camera lens DVR keeps rebooting Place the HDD near the power connector or replace the HDD HDD failure Test with another HDD Test with another HDD cable Make sure HDD Master and Slave mode is set correctly Cannot detect USB ThumbDrive Test with another USB ThumbDrive see the list in APPENDIX 4 When two Seagate power saving HDDs are installed Donotuse 2 Seagate power saving HDDs the DVR cannot be switched on successfully simultaneously Cannot view the DVR over the network with a web Update the JAVA programme browser Update the firmware of the software AP 12 Appendix 1 HDD Installation Cable Select NOTE Always set the HDD jumper
40. ppear on the screen The software AP will start recording automatically NETWORK BACKUP 1 2 Press the za button to enter the system setting page prora Backup the recorded files to the PC from DVR ne i via network reer Enter the backup information Press Start an an Success Convert Play File ae HDDNum MASTER Calne User Lalo FilePath ENDocuments aad Setingtcaderioe 1 a h Success APPLY Do you want to convert this file Convert 100 ad 7 w s sessesess Y pism i S euasesenascsccceeranss F on 5 05 12 27 09 10 44 gt Hu Playback Information Time Progress Bar Functions 1 De interlace 2 De blocking 3 OSD 4 AVI Convert 5 3 4 5 Config Setting DVR4MQAE 29 VELLEMAN 6 Watermark 7 Open Previous 8 Open Next File 4 Playback Control Buttons Play Stop Pause Fast Rewind Fast Forward 5 Snapshot 6 Close the Player ALARM Press the ea button to enter the system setting page 1 Alarm Trigger Enable or disable the email and FTP notification function 2 Alarm Method Two notification methods email and or FTP 3 Post Number Set the MJPEG pictures 1 10 pictures 4 Alarm Duration Set the duration time of the motion trigger recording 3 sec 15 sec 30 sec 1 min or 30 min 5 Alarm Refresh Clean the alarm message shown
41. r 5 ALARM LIST List of alarm triggered recorded files 6 MOTION LIST List of motion triggered recorded files 7 TIME SEARCH Search by specific time period YEAR MONTH DAY HOUR MIN NOTE Move the cursor to the specific recorded file and press ENTER to play the video and press stop m button to return the live display b 2x Digital Zoom Press the ZOOM button on the front panel of the DVR to enlarge the picture of the selected channel 2x digital zoom Therefore use the A Y lt b to navigate DVR4MQAE 19 VELLEMAN 30 MON 14 50 37 400 GB 2005 R ON 14 50 37 DIGITAL ZOOM ee o a 1 Press the ZOOM button again to exit the zoom picture 2 Press A V lt b button to move the zoom position c Key Lock 1 Key Lock On Press MENU ENTER buttons to key lock Auto key lock refer to 9 k Advance Menu_System 2 Key Lock Off Press any key except SHIFT and POWER buttons and key in the password to exit Key Lock mode 3 Password As to the password setting refer to 9 k Advance Menu_System d The N P System 1 Press POWER button to shutdown and press POWER to switch to PAL system press till the monitor shows the video image of the DVR 2 Press POWER button to shutdown and press POWER lt 4 to switch to NTSC system press till the monitor shows the video image of the DVR e USB
42. rded files may be overwritten without further warning notices Yas Wy e y ak Tk 5 PP DVR4MQAE 7 VELLEMAN b Playback Press PLAY the DVR will display the last recorded video 1 FAST FORWARD F F amp FAST REWIND REW You can increase speed to fast forward and rewind In the playback mode Press gt gt once to get 4X speed forward press twice to get 8X speed etc The maximum speed can reach 32X Press lt lt once to get 4X speed rewind press twice to get 8X speed etc The maximum speed can reach 32X The type of recording image size Frame or CIF will also be shown on the screen 2 PAUSE IMAGE JOG Press the IP button to pause the current image displayed on the screen In the Pause mode Press gt gt once to forward frame by frame Press lt lt once to rewind frame by frame 3 STOP Press the m button under all circumstances to return the DVR to live monitoring mode 4 CHANNEL SHIFT Display mode Press MODE HH button to display 4 channels Full Screen Switch Press or I button to show the full screen channels Channel display switch Press SET to change channel display position Press A Y lt gt to select the channel you would like to change Press or select the channel you would like show Press ENTER button to confirm Press MENU to quit 5 SLOW PLAYBACK Press SLOW button to get 1 4
43. see 10 f Alarm Add the recipients email accounts in the Mail Account column The detailed information SMTP server username and password refers to the email system supplier Please type in the entire email address in the Mail from column to ensure the emails will not be blocked by SMTP In some cases the mail server requires to verify the password Enter the user name and password 5 After setting press APPLY to confirm FTP Press the za button to enter the system setting page 1 When alarm or motion is triggered a video copy file can be captured The DVR can upload the captured images to the assigned FTP site Enter the detailed FTP information NOTE To activate the FTP notification function enable the function of the FTP notification in the Alarm setting first 3 After setting press APPLY to confirm DVR CAMERA SETTING Press the a button to enter the system setting page 1 Each camera channel can be adjusted independently 2 Select the desired camera channel Press Edit to enter the setting box Title Enter the camera channel name up to 6 characters Adjustment Adjust the BR brightness CT contrast ST saturation HUE hue REC recording of the camera After setting press OK and press APPLY to confirm DVR4MQAE 27 DDNS Yenfy Password w Server 211 768599 7 FTP Verily G Yes C
44. st the Brightness Contrast Saturation Hue of each channel The level is from 0 to 255 The default value of BRIG is 110 others are 128 COV COVERT Select YES to mask the selected channel which is under recording When this function is activated the COV words will be shown on the screen REC RECORD Select YES to enable the record function Select NO to disable the record function PRE NEXT Select PRE to go to the previous page Select NEXT to go the next page N o gt o NOTE TITLE 6 characters letters or symbols BRIG from 0 255 the default value is 110 CONT from 0 255 the default value is 128 SATU from 0 255 the default value is 128 HUE from 0 255 the default value is 128 CONV YES or NO REC YES or NO g Advance Menu DETECTION Move the cursor to DETECTION and press ENTER The screen will show the following options DETECTION DETECTION SETUP DETECTION TIMER DETECTION SETUP DETECTION 1 TITLE Show the title of each camera channel DVR4MQAE 12 VELLEMAN 2 DET Select ON to activate the motion detect function of each channel Select OFF to deactivate the motion detect function of each channel 3 AREA Press the ENTER button to set detection area Pink blocks represent the area that is not being detected while the transparent blocks represent the area that is under detection Press ENTER
45. start the DVR to get the IP address Web Port Jao IP TYPE Static IP PPPOE DHCP EXIT APPLY DVR4MQAE 25 VELLEMAN 4 Web Port The DVR can be viewed over the network with software AP or a web browser Typically the TCP port used by HTTP is 80 However in some cases it is better to change this port number for added flexibility or security Valid number is 80 19999 DDNS Press the ea button to enter the system setting page 1 DDNS is a service for transforming dynamic IP to a specific Hostname 2 DDNS Apply Go to a website providing free DDNS services and apply a Hostname See the example 3 Enabling the DDNS function Enter DDNS username in the username column Enter the DDNS password in the password column Enter the Hostname in the Domain column Choose the DDNS system name After setting press APPLY to confirm DDNS APPLY EXAMPLE th m etag rog Network Mail FIP DYR Devxe Detection Network Backup Search Last Gezenal Account Online User Info File Path 4CH DVR om DONS ns 792 163 7 10 DDNS Enable Diable User Name onae Password Domain hostname dyndns org System Nae fdyadns X e Go to a website providing free DDNS services Example http www dyndns org e Create an account in DynDNS e After having created your account
46. th a web browser This function is suitable in both Windows 2000 and Windows XP Step 1 Type IP address into the URL address box and press ENTER NOTE If the TCP port number is not 80 see the example below IP address 192 168 1 10 Port number 888 gt Key in 60 121 46 236 888 into the URL address box and press ENTER Oo p mp mes CAD sme a Co TOn T yn IP Surveillance New Generation gt Usemame gt Password A ia Download AP Download JAVA L Reset ff Submit I Download ap Ii Download Java DVR4MQAE 32 VELLEMAN Step 2 Press the Download JAVA button Download JRE 5 0 Update 4 NOTE JAVA setup file Sie 5 0 0 is also included in the licensed software AP disk Step 3 Press Accept License Agreement kK __ e A ain ep ep mp mero I0 aS a ones O42 Gee umer Gwe y gt R dc Crean ee osa oe Accept license agreement EER S _ Windows Offline Installation i Windows Online Installation Step 5 Take Windows Offline Installation as an example Save the setup file jre 1_5_0_04 windows i586 p on the desktop of PC Click twice on the jre 1_5_0_04 windows i586 p to setup DVR4MQAE 33 VELLEMAN Step 6 After installation please type the IP address of your DVR into the URL address box and press ENTER You will see the login page Key in the username and password 320 228 Change Resolution 640
Download Pdf Manuals
Related Search