MTG600 Trunk Gateway User Manual V2.0
Contents
1. 2 8 2 Coder Group Coder Group Coder Group ID O default setting mi Payload Type Packetization Time Rate Value ms kbps Coder Silence Suppression Figure 2 8 2 Coder Group Coder group description ID standard for Voice ability total with 8 groups where O is the default group ID Coder Group ID number the codec that equipment supports in the grouping will be displayed in O group Default value cannot be modified Coder Support 3 kinds of voice codec G 711A U G 729 G 723 Payload Type Value Each codec has a unique value refer to RFC3551 Voice Codec packetization time user can define different kinds of coding Packetization Time ms and decoding minimum packetization time It is disabled by default During talking the bandwidth occupied by voice transmission Silence Suppression will be released automatically for silence party or when talk is paused ID standard for Voice ability total with 8 groups where O is the default group ID Coder Group ID number the codec that equipment supports in the grouping will be displayed in O group Default value cannot be modified 2 8 3 Dial Plan Dial Plan Dial Plan ID Total 1 Page 1 m Add Figure 2 8 3 Dial Plan 28 57 MTG600 User Manual Dial plan used for configuring the receiving number user can configure different prefix number these rules can be divided into 5 groups with a dial plan ID where O is the default setting Notes 1 In o2. Network PRI Config 557 Config R2 Config PSTN Group Config SIP Config IP Group Config Call Routing Number Manipulation Voice amp Fax Maintenance MTG configuration flow chart below Login web Configure IP Configure PRI SS7 Trunk Configure PSTN Group Configure SIP Trunk Need to IP Apu up No 4 Configure Routing EE Manip Yes o ulation ai Na k Restart Device a 8 57 Yes Configure IP Group Configure Manipulation MTG600 User Manual 2 3 Status amp Statistics MTG600 User Manual Open the operation of the navigation tree information node and can view the device information and state system Figure 2 3 1 Status amp Statistics Status amp Statistics E1T1 Status PSTN Trunk Status P Trunk Status PRI Call Statistics 2 3 1 System Information 587 Call Statistics SIP Call Statistics System information interface shows the general information and version information Figure 2 3 1 System Information System Information General MAC Address Service Ethernet Interface FEU Management Ethernet Interface FE1 DNS Server System Time System Uptime Traffic Statistics Version Device Model Hardware Version DSP Version Web Version Saftware Version Time Built 00 65 34 56 38 20 172 30 65 25 192 168 11 1 255 255 0 0 172 30 0 1 259 255 255 0 2012 4 26 23328 5h22m4s
3. Protocol of sub menu 587 Trunk the start CIC No must be less than 4096 2 When option ANS has been selected in Protocol of sub menu 357 Trunk the Start CIC No must be less than 16384 CIC circuit identification code is an important parameter of SS7 circuit It should be confirmed with service provider If the CIC is mismatched it will result in one way voice communication SS7 Circuit Add Trunk No The Trunk No here corresponds to the Trunk No of SS7 trunk E1 T1 port No Fill in the port number of E1 T1 Assign E1 T1 to selected SS7 trunk Start Channel The start of SS7 channel trunk 21 57 MTG600 User Manual Start CIC No An initial circuit number to this E1 T1 matches by both parties Count A total of 32 channels 2 6 4 SS7 Circuit Maintain According to the different operating modes 7 circuit maintenance objects into two categories ports and channel 557 Circuit Maintain Operation Mode E1 T1 Port No 0 1 2 3 Protocol Type status Slect All Actived Disable Fault RA Alarm AIS Alarm ISDN SS Signal Alarm Frame Sync Idle Signal Busy L blocked R blocked B blocked Blocking Unblocking Reseting Notes L Blocked Local Blocked R Blocked Remote Blocked B Blocked Both Sides Blocked Figure 2 6 7 SS7 Circuit Maintain E1 T1 SS7 Circuit Maintain E1 T1 description Operation Mode There are port operation and channel optional Display the port number Proto
4. Are you sure will be popped up and then click OK 52 57 MTG600 User Manual 3 FAQ 3 1 How to get the IP address if user modified or forgot the default IP There are one way to get the IP address 1 Connect the CONSOLE with your PC Serial Port The baud rate is 115200 bps The user name and password is admin When users logged in system and then run command show int for getting the IP Please refer to http www dinstar com service faq 145 aspx 3 2 If meet other questions please from Dinstar website and download trouble shootingV4 0 URL is http www dinstar com service Training aspx 4 Glossary PRI Primary rate interface DND Do not Disturb FMC Fixed Mobile Convergence SIP Session Initiation Protocol DTMF Dual Tone Multi Frequency USSD Unstructured Supplementary Service Data PSTN Public Switched Telephone Network STUN Simple Traversal of UDP over NAT IVR Interactive Voice Response IMSI International Mobile Subscriber Identification Number IMEI International Mobile Equipment Identity DMZ Demilitarized Zone 53 57
5. ep ADAN vi oak koi ON 9 2 32 PEUT ES AUS Em 11 2 9 9 NN RA ESET tk a e ESAE 12 DSA P TRUE SA S ka ll l kk al aa n 12 2 9 PRE CSU SASINEN e bien tede ar 13 2 OSS MONK al SUILISUCS Aa 14 ES CAESA E AAA nn ui 14 ZAIN OWO A A Tm 15 O ONN Seren o do n 15 2 3 LPRI Parameter aan 16 2 5 2ER A ee ee 17 2 6 SS CON ILE a e ke n toi ke ae oke 18 26 1557 MUNK s sik a dos ki ba a aa ka a nina 18 2 62 55 STEN IT VO K petit asyet O E 20 210 9 5S PE CUIU et ea tie ok A a OO ELM ne MEC IM baay 21 2 04 551 CASE Manta ki a t iii ekta a ko a ines ees pa Dat a pet Cone tus enn es an ee Sean een at 22 PA PII niam a aie ea e Dres 24 DI SEND A ie ta aie cara eee mance ee cca ees aaa 24 2 2 IS EHE acis ee te antes D n EL uM E M Ef 26 2 5 PS IN Group Caisse 27 2 5L ELI Parameler seen see ur 27 282 Ges Groesse 28 28 Da Bl amt sen ee ee Se ee ee 28 2 8 4 Dial Time OLN e NERAL Cn it cde Gan a e ta e ta bk ot a a at ek ate to e ak a pt ob date 30 2 5 9 PS TNSPEOPIG a iia 30 Pedo UE A anasto act aso acess 31 20 1 ESTN Group Management a 3 22 32 MTG600 User Manual DOSS COME cm 33 2 9 1 SIP Parameter an een ee 33 292 RS eo Messa ee se 33 2 9 OUP ACCOUNT e ee Desk 34 2 AOUP Group CONTIG an dada adas 35 PAN MI Muro c 35 210 2 IU 37 2310 Sa P Group Mana PCIe HU ee ee 37 DNA CAMERON A kd ot a n n a n l p ak ak akyon 38 ZAI Routing Parameter 2 cioe ae op Sou ewa vdi ap eet ewa vi kap eet ewa vos op Sou ea 38 2 1172 PSTN SIP ROULUIT
6. n Caller number prefix Mean any caller number Starting from the right to retain the called number digits 43 57 MTG600 User Manual 2 12 2 PSTN gt IP Caller PSTN gt IP Caller Total 0 gt Figure 2 12 4 PSTN gt IP Caller PSTN IP Caller Add Index Description PSTN Group Callee Prefix Caller Prefix Number of Digits to Strip from Left Mumber of Digits to Strip from Right Prefrx to Be Added Suffix to Be Added Number of Digits to Reserve from Right NOTES 1 Fields with are MUST 2 in Callee Prefix or Caller Prefix field means wildcard string Figure 2 12 5 PSTN gt IP Caller Add PSTN gt IP Callee configuration parameters and IP gt PSTN Caller configuration parameters are the same PSTN PSTN Callee Total o Figure 2 12 6 PSTN PSTN Callee PSTN gt PSTN Callee configuration parameters with the above is basically same only more of a number type parameter Common number types are Not Configured Unknown International National Network Specific Subscriber Abbreviated PSTN gt PSTN Caller Total 0 gt 44 57 MTG600 User Manual Figure 2 12 7 PSTN PSTN Caller Presentation indicator parameter used to indicate the status of the operation The operation of the option the right are Not configured Allowed Restricted IP gt PSTN Callee Total 0 gt Figure 2 12 8 IP gt PSTN Callee IP gt PSTN callee
7. sending SL TN Enable 18 57 MTG600 User Manual SS7 is a standard protocol to initiate a calling connection with SPC exchange Notes 1 Trunk No is a shared data therefore SS7 Trunk No can t be the same as PRI Trunk No 2 SPC length is 24bits when option ANSI or ITU CHINA is selected in item Standard Type 3 SPC length is 14bits when option ITU is selected in item Standard Type 4 SPC Length represents the structure of OPC DPC SPC View Mode indicates which input format is selected for OPC DPC structure 5 When SPC length is 24bits and Hex are selected the structure is like xyz and x y z must be hex number between OO FF eg 33AA55 6 When SPC length is 14bits and ITU Pointcode Structure are selected the structure is like X y z and x z must be decimal number between 0 7 and y must be decimal number between 0 255 eg 6 222 3 7 When SPC length is 14bits and Hex are selected the structure is like xyz and x z is a 3 bit hex number y is a 8 bit hex number eg 202E 100 00000101 110 SS7 trunk add The number of SS7 trunk Generally a DPC will establish a SS7 trunk number Select Trunk No respectively SS7 trunk number cannot be conflict with PRI trunk number After SS7 trunk is established assign E1 T1 to SS7 trunk in SS7 Circuit option Trunk Name Name of trunk it can be edited to any name user want Protocol SPC types ITU T 14 bit ANSI 24 bit ITU CHINA 2
8. I 15 INVALID Call with charge 7 8 Philippines 01 A 1 A 5 A 5 INVALID l 15 A 3 Call with charge A a venere 01 A 1 A 9 A 5 INVALID 115 A 3 Call with charge a 11 Fe Bolivia 01 A 1 A 5 A 5 l 15 l 15 A 3 Call with charge 14 India 01 A 1 A 4 A 5 INVALID I 10 A 3 Call with charge E 15 Indonesia 01 A 1 A 6 A 6 I 15 I 15 A 3 Call with charge 16 Korea 01 A 1 A 5 A 5 INVALID I 15 A 3 Call with charge E 17 Malaysia 01 A 1 A 6 A 6 I 15 I 15 A 3 Call with charge M 18 P kama 01 A 1 A 5 A 5 INVALID 115 A 3 Call with charge 19 Singapore 01 A 1 A 6 A 6 I 15 I 15 A 3 Call with charge 20 Thailand 01 A 1 A 1 A 6 I 15 I 15 A 3 Call with charge Figure 2 7 1 R2 Parameter It is the default configuration for MTG600 Description says the state name means the different countries supported R2 parameters standards According to demands add R2 parameters of user countries 24 57 MTG600 User Manual R2 Param Add Config Mode Typical m Description Calling Party Category National subscriber Seize Timer ms 5000 Pratect Timer ms 300000 S MI Receive Timer ms Wait Response Timer ms MF Off Timer ms 3000 Wait Release Timer ms 3000 Group I DNIS end flag 115 E ANI end flag 115 Ka Group A Lu s i d p To do TER Address Complete Request next DNIS Request next ANI Request category Request Change to Group C NVALID Request Last Digit Again Repeat All DNIS Digit Group B Unallocat
9. Profile PSTN profile is used to configure PSTN call number rules and parameter PSTN Profile Add PSTN Profile ID Description Coder Group ID RFC2833 Payload Type DTMF Tx Priority 1st DTMF Tx Priority 2nd DTMF Tx Priority 3rd Overlap Receiving Remove CLI Play Busy Tone to FSTN PSTN profile add description PSTN Profile ID Description Code Group ID RFC2833 Payload Type 1 2 3Tx DTMF Option Overlap Receiving Remove CLI Play busy tone to PSTN PSTN Profile ID Description 2 8 6 PSTN Group mJ p RFC2833 SIP INFO Inband Disable Mot remove Reset Cancel Figure 2 8 8 PSTN Profile Add There are three ways to send DTMF RFC2833 SIP INFO INBAND in accordance with the priority choice to send the configuration mode Not enabled by default only user enables this feature Dial plan and Dial timeout would work PSTN group configuration can be different E1 T1ports or the same port in different time slots to form a PSTN trunk group based on different channel selection PSTN Group Group ID Name Channel Selection r2 0 Cyclic Ascending r2 12 Cyclic Ascending Total 2 Page 1 Add Figure 2 8 9 PSTN Group 31 57 MTG600 User Manual PSTN Group Add Trunk Group ID Name Channel Selection Ascending ad Cyclic Descending Descending Figure 2 7 10 PSTN Group Add Adding PSTN group needs to fill three parameters trunk group Numbers trunk group Name Channel selecti
10. Received Sent 20 130 335 41 058 339 MTG800 PCB 01 v 22 03 16 HW 12 2 02 02 01 2 02 02 01 2012 04 26 09 53 16 9 57 MTG600 User Manual Table 2 3 1 System Information Management Ethernet Interface 10 57 MTG600 User Manual 2 3 2 E1 T1 Status E1 T1 Port Status Physical Status NOTES Actived Im Disable MM Los Alarm WRAAam Aasaam BM sDN SS7 Signal Alarm E1 T1 Channel Status o ii iii iii iii iii iii ii o eee ee u RPE Port 3 Status Frame Sync Idle Signal Busy Fault Disable L blocked R blocked B blocked Color EI E E E E Ki E E Totalize 1 30 1 0 B4 42 0 0 NOTES L Blocked Local Blocked R Blocked Remote Blocked B Blocked Both Sides Blocked Figure 2 3 2 E1 T1 Status Table 2 3 2 Description of E1 T1 status 1 LOS Alarm Signal loss alarm this alarm is created when receiving is lost please check the physical connection whether disconnected 2 RAI Alarm Receive remote alarm indication it is a signal transmitted in the outgoing direction when a terminal determines that it has lost the incoming signal Receiving remote alarm indication RAI means the far end equipment over the T1 line has a problem with the signal it is receiving from the upstream equipment 3 AIS Alarm The Alarm Indication Signal AIS failure is declared when an AIS defect is E1 T1 Port Status detected at the input and the AIS defect still exists after the Loss of frame failure which
11. Received 19 596 807 bytes Sent 39 387 354 bytes Version Device Model MTG600 Hardware Version PCB 01 DSP Version v 22 03 16 HW 12 Web Version 2 02 02 01 Software Version 2 02 02 01 Time Built 2012 04 26 09 53 16 Figure 2 1 3 Description of System Information 2 2 Web interface structure and navigation tree After entering configuration page according to demand choose Chinese interface or English interface the default 1s English interface Caution The password current used is a default password please change to a new password for system security System Information General MAC Address Service Ethernet Interface FEU 00 65 34 55 38 20 172 30 65 25 255 255 0 0 172 30 0 1 Management Ethernet Interface FE1 192 168 11 1 255255 25510 DNS Server System Time System Uptime Traffic Statistics Version Device Model Hardware Version DSP Version Web Version Software Version Time Built 2012 4 26 23280 5h 17 m 56 5 Received 19 665 160 Sent 39 596 868 MTG600 PCB 01 v 22 03 16 HW 12 2 02 0201 202 02 01 2012 04 26 09 53 16 Figure 2 2 1 System Information Users through to traverse the left navigation tree and can complete view edit and configuration device in the right configuration interface 7 57 Figure 2 2 2 Navigation tree Status 4 Statistics E1 T1 Status PSTN Trunk Status IP Trunk Status PRI Call Statistics So Call Statistics SIP Call Statistics
12. SIP Trunk SIP Trunk Add Trunk No Trunk Name Remote Address Remote Port Outbound Proxy Outbound Porxy Port Local Domain Support SIP T Get Callee from Register to Remote Incoming SIP Authentication Type IP to PSTN Calls Restriction PSTN to IP Calls Restriction IP to PSTN Time Restriction Detect Trunk Status Detect Period 35 635 Enable SIP Trunk li Disable Disable Request line IP Address Disable Yes Yes Figure 2 9 3 SIP Trunk Add MTG600 User Manual SIP trunk description Trunk No The range of number is 1799 Trunk Name Description the trunk Remote Address IP address of remote platform interfacing with this equipment Q 931 port of SIP of remote platform interfacing with this equipment the default is 5060 Outbound Proxy SIP proxy IP address Outbound Proxy Port The default proxy port is 5060 Local Domain Refer to SIP parameter Support SIP T Not the target configuration the parameter is always no it is for SS7 Remote Port Get Callee from Received the called number from request domain or To header filed Defined by IETF work group RFC3372 it is a standard used to establish remote Register to Remote communication between SIP and ISUP the default is Yes if SIP trunk does not support then setitto No Incoming SIP There are two modes IP address and Password If user selects password then Authentication Type password will be filled IP to PSTN side of t
13. and Max Length are equal to the total number of possible length minus the prefix length 3 When overlap dialing called number length sure and then the Min Length and Max Length will 29 57 MTG600 User Manual be set to the same value to accelerate connection rate 4 Prefix configuration compatible digit map mode 2 8 4 Dial Timeout Dial Timeout Total 1 Figure 2 8 5 Dial Timeout Dial Timeout Add Dial Timeout ID Description Max Time for Collecting Prefix Time to Reach Min Length after Prefix Time to Reach Max Length after Min Length NOTE li Max length equals to Min length in Dial Plan Time to Reach Max Length can be any value Figure 2 8 6 Dial Timeout Add Dial timeout description Dial Time ID The number to identify a dial timeout rule Max Time for Collecting Prefix Generally refer to the time from user dial first digit to harvest in prefix number Time to Reach Min Length after Prefix After receiving prefix number the number has not yet reached the length of the minimum receiving number the length of timeout Time to Reach Max Length after Min After receiving number the number has reached the minimum Length length but not reached the maximum length of the dial timeout 2 8 5 PSTN Profile PSTN Profile m 0 Default 0 101 RFC2 SIPIN Inband Enable 0 0 Default Not remove No Total 1 Page 1 v 30 57 MTG600 User Manual Figure 2 8 7 PSTN
14. description Refer to IP Group any means any trunk group Called number prefix means any called number Caller number prefix Means any caller number Number of Digits to Strip from Remove the called number digits from the left left Number of Digits to Strip from Remove the called number digits from the right right Prefix to be Add Add a called number prefix Suffix to be Add Add a called number suffix Number of Digits to Reserve Starting from the right to retain the called number digits from Right Number Type Common number types are Not Configured Unknown International National Network Specific Subscriber and Abbreviated IP gt PSTN Caller IP gt IP Callee IP gt IP Caller configuration parameters in the previous number manipulation rules have been mentioned please refer that section IP gt PSTN Caller Total 0 Figure 2 12 9 IP gt PSTN Caller IP gt IP Callee Total 0 T 45 57 MTG600 User Manual Figure 2 12 10 IP gt IP Callee IP gt IP Caller Total 0 gt Figure 2 12 11 IP gt IP Caller 2 13 Voice amp Fax Voice amp Fax Configuration Voice Parameter Disconnect call when no RTP packet Period without packet Gain from PSTN Timeout of No Answer Call from PSTH Call from IP Fax Parameter Fax Mode Fax Tx Gain Fax Rx Gain Packet time undant frame in packet Data amp Fax Control Data Fax DTMF
15. device customer can regain the port s default IP Then enter the IP address of device in the browser address bar Customer will see the following page 3 172 30 65 25 80 BAP a AP SAIS 37 GoAhead Ars admin Figure 2 1 1 Login Interfaces The default user name and password is admin To guarantee the system safety when login for the first time The system will prompt the user to modify the password The interface is shown as below Password Modification Old Password New Password Confirm Password Save Figure 2 1 2 Modify Password Users through to traverse the left navigation tree and can complete view edit and configuration 6 57 MTG600 User Manual device in the right configuration interface Status amp Statistics E1 T1 Status PSTN Trunk Status IP Trunk Status PRI Call Statistics 557 Call Statistics SIP Call Statistics Network PRI Config SS7 Config R2 Config PSTN Group Config SIP Config IP Group Config Call Routing Number Manipulation Voice amp Fax Maintenance Caution The password current used is a default password please change to a new password for system security System Information General MAC Address 00 65 34 56 38 20 Service Ethernet Interface FE0 172 30 65 25 255 255 0 0 172 30 0 1 Management Ethernet Interface FE1 192 168 11 1 255 255 255 0 DNS Server System Time 2012 4 26 23 27 26 System Uptime 5h17m22s Traffic Statistics
16. 2 11 7 IP gt PSTN Routing 40 57 MTG600 User Manual IP 2PSTN Routing Add Index Description Source Type Trunk Type IP Group Callee Prefix Caller Prefix Destination Type Destination PSTN Group NOTE in Callee Prefix or Caller Prefix field means wildcard string IP gt PSTN Routing Routing Call from IP to PSTN IP gt PSTN routing configuration and PSTN gt PSTN routing configuration are similar the only difference is PSTN destination group 2 11 5 IP gt IP Routing Figure 2 11 8 IP gt IP Routing IP 2IP Routing Figure 2 11 9 IP gt IP Add 41 57 MTG600 User Manual IP gt IP Routing Add Index Description source Type Trunk Type IP Group Callee Prefix Caller Prefix Destination Type Destination IP Group Rese NOTE in Callee Prefix or Caller Freit field means wildcard string IP gt IP routing configuration and PSTN gt IP configuration are similar The only difference is that the destination is the IP group 2 12 Number Manipulation Select Number Manipulation in navigation tree the display interface is shown as below Figure 2 12 1 Number Manipulation Number Manipulation PSTN IP Callee PSTN IP Caller STN PSTN Callee PSTN PSTN Caller PL PSTH Callee P PSTN Caller IP IP Callee IP IP Caller Number Manipulation is used to replace numbers User can replace and remove the inbound and o
17. 4 R2 Trunk Add PRI trunk description The unique identifiers of R2 trunk system customs eight relay index number Used to identify and describe R2 trunk E1 Port No According to T1 E1 port position sequence sort usually starting from O Protocol Param Select R2 parameter group 26 57 MTG600 User Manual 2 8 PSTN Group Config 2 8 1 E1 T1 Parameter Clock source of E1 T1can be selected Remote or Local If selecting E1 T1 port to portO when user modified portO portO 3 will be changed together with portO Port4 7 changed following the port4 E1 T1 Parameter E1 T1 Clock Source Remote m m 0 E1 A LAW DF HDB3 Short Haul 10DB m 1 E1 A LAW CRC 4 HDB3 Short Haul 10DB m 2 E1 A LAW CRC 4 HDB3 Short Haul 10DB m 3 E1 A LAW CRC 4 HDB3 Short Haul 10DB Figure 2 8 1 E1 T1 Parameter E1 T1 parameter description Work Mode E1 T1 the default is E1 PCM Mode PCM mode A LAW and Mu LAW the default is A LAW The frame modes of E1 are DF CRC 4 CRC4_ITU the default is CRC 4 the frame modes Frame Mode of T1 are F12 F4 ESF F72 the default is F4 Line codes of E1 are NRZ CMI AMI HDB3 the default is HDB3 The Line codes of T1 are Line Code NRZ CMI AMI B8ZS the default is B8ZS Cable length E1 lines docking the environment will affect the E1 line signal strength Line Built Out signal strength according to DB value to select the long term or short term 27 57 MTG600 User Manual
18. 4 bit Protocol Type Supported two protocol types ISUP and TUP Signaling Point Code format includes hexadecimal system and ITU pointcode SPC Format structure decimal system OPC Original Point Code DPC Destination Point Code Service Type SS7 service types ISUP ISDN User Part and TUP Telephone User Part Indicate the network property of SS7 including International Network International Spare National Network National Spare the default is National Network Indicator Network this type is used in China USA and Japan International Network is generally used in inter office switch room others will be selected according to physical circumstances Note 1 If protocol standard chose ANSI or ITU CHINA and then the SPC length is 24 bits 2 If protocol standard chose ITU and then the SPC length is 14 bits 19 57 MTG600 User Manual 3 SPC length performance on the OPC DPC structure SPC pattern instructions of the different structure OPC DPC input formats 4 When the SPC length is 24 bits and chosen ITU OPC DPC structure format is x y Z x y Zis a number of 0 255 such as 22 222 77 5 When the SPC length is 24 bits and chosen Hex OPC DPC structure format is xyz x y z must be Hex number of 00 FF such as 33AA55 6 When the SPC length is 24 bits and chosen ITU OPC DPC structure format is x y z x z must be decimal value y is decimal number 0 255 such as 6 222 3 7 When the SPC lengt
19. DINSTAR FSRA MTG600 Trunk Gateway User Manual V2 0 Dinstar Technologies Co Ltd File Name Document Version Firmware Version Date Revised by MTG600 User Manual Revision Records MTG600 trunk gateway user manual 2 02 02 01 03 05 2012 Technical Support Department MTG600 User Manual Content ToProduct Introductio xoi ee ee 1 MEO Ru W L ai n e it ti tt n kaka a a e a ta ta on a kt aa kk a a et anc a ko e e a ou tk a ya a 1 D 2 Eguipmelt ST UCU et tt at ks lt kali ka e kai tl tl d diu ka tk ab a tek aba 2 122 1 Reap Viewer 2 1 22 PRONE VIEW oct oet pcena odds ape da Ctm ad e vtae ut reda Lata oi ka Lacie 3 1 2 3 RJ 48e Eine sequence unen A AA uel cua oa AAA 4 ES Functions and Features 4 iaa 4 1 3 1 Protocol standard supported ico er tir data ob ewa eda SEES os ewo ER EY ea oun Cua e po koen kad ese da 4 TS Ze SYST M FUNCION tl l e a l alor n aee a bat a ks f tem dui dto ason 4 1 3 3 Industrial standards supported cccccccccsessecccceeeseccecceeeseceeeeeaeceeeseaeeeeessauaneseeees 4 1 3 4 General hardware specification ccccccssssecccccessececcecesseccccscuseececseaseesesseaseeteces 5 2 Parameter Sette as 6 P N MPa mm P re a e e A a A ee n e a on ae oo ao 6 2 2 Web interface structure and navigation tree oocccnccccnocnnnnnonanonnnnnnnnnnnnnonnnnnnnnnonanonnnnonanoss 7 2 3 9 Latus SE STAU Seren 9 2 3 1 System Informal saaa an tik voye a aw dw os si kaka kai a ask ae w p
20. IB need de 38 2 11 35 PSTNE PSTN Routine sn tennis 39 ZA AIP SP SIN BOULE cesset dial 40 2 11 5 1P gt P Routing 25 5 an ki ko ae tr A ai 41 212 Number MaitplildttOfio sso sn D ot ee la I a n a ba e a af 42 ZI D PSTN SIPCallee kob ok baton ee ca ee e ta a t a a krak a DO Bere 43 2 122 ASIN RCA ka aon nt e a ft a kk ae Di a epi ann 44 DAS VOICE SE PAK c E 46 2 14 Manase ment Parameter see 48 214 2 SS A ee se esse 49 DN NM Spr e a ak ia 50 NAOT ACA RES Lud etes cess ioo ae 50 2 143 VerstOn IOMA NON aa nenn 51 Pd Een aber WO OA cect ch eek 51 2 T2 NOE PASS W OFC au een 51 DAA Restart Device anne nennen aes ior n orien ort nite 52 SAS 53 3 1 How to get the IP address if user modified or forgot the default IP 53 3 2 If meet other questions please from Dinstar website and download trouble shootingV4 0 MTG600 User Manual 1 Product Introduction 1 1 Overview MTG600 is a trunk gateway aimed at small and medium enterprise and used to help enterprise to realize the evolution from the traditional PBX to voice IP On the one hand it supports PRI SS7 protocol and adopts standard T1 E1 trunk interface to realize docking with traditional PBX On the other hand adopt standard SIP protocol docking with various soft switch to ensure PSTN seamless access to IP voice NGN network and achieving VolP FolP and more value
21. IP IP Routing amp Manipulation Routing before Manipulation Incoming Calls from PSTN Routing Priority First PSTN gt IP then PSTN PSTN Routing amp Manipulation Routing before Manipulation Figure 2 11 1 Routing Parameter Inbound and outbound call routing configuration The key steps how to Configure routing The more accurate routing configuration index values should be smaller Any and are useful suggesting configuration to avoid cannot match the routing 2 11 2 PSTN gt IP Routing PSTN IP Routing 255 any Any Any O 66 16 Total 1 Figure 2 11 2 PSTN gt IP Routing 38 57 MTG600 User Manual Route PSTN IP Add Index Description source Type FSTN Group Callee Prefix Caller Prefix Destination Type Group Destination IP Group 0 66 167 NOTE in Callee Prefix or Caller Prefix field means wildcard string Figure 2 11 3 PSTN gt IP Add PSTN gt IP Routing Routing Call from PSTN to IP PSTN gt IP routing description Routing index number 0 255 PSTN gt IP Routing priority rule is according to the index to set Reference dial plan Description Describe the routing Source Type Source type is PSTN group or PRI SS7 trunk PSTN Group Refer to PSTN Group Config any means any trunk group Callee Prefix Callee number matches prefix number Is a wildcard representing any callee number Caller Prefix Caller number matches pref
22. Parameter Continuous time Signal interval Threshold for detection El a a 5 m un un ajja ly EJE n Figure 2 13 1 Voice amp Fax 46 57 MTG600 User Manual Voice amp Fax description Disconnect Call when no RTP When selected Yes detected call s silence time packet longer than silence timeout that for a long time not received RTP packets then hangup the call Voice Parameter Two modes are provided T 38 Pass through Fax Mode default option is T 38 Fax Parameter Packet time Data packing duration Redundant frame in packet The length of frame in RTP packet Whether to allow the control of voice data Data amp Fax Control Whether to allow the control of fax The time interval between two different DTMF Parameter Signal interval frequency signals Threshold for detection Frequency detection threshold 47 57 MTG600 User Manual 2 14 Management Parameter Management Parameter WEB Configuration WEB Port Telnet Configuration Telnet Port Syslog Configuration Syslog Enable Qos Qos Type NTP Configuration NTP Enable Yes No Primary NTP Server Address 54 2365 05 53 Primary NTP Server Port 123 Secondary NTP Server Address 18 145 0 30 Secondary NTP Server Port c ki Lu 04800 Time Zone GMT 8 00 Beijing Singapore Taipei Sync Interval MOTE The device must restart to take effect Figure 2 14 1 Management Paramete
23. added service MTG600 supports intelligent multiple trunk routing technology makes the operator easy to manage trunk routing by price optimum rule and the automatic switch over between multiple trunk routing makes the network have high reliability MTG600 has good call processing ability and provides 2 4 T1 E1 interface It is able to handle a variety of signaling protocol and voice decoding It supports the rich GUI configuration the user easily set and maintenance system Mainly includes the following kinds of models e 2E1 e 4E1 A typical network diagram shows the function of MTG600 as below Figure 1 1 1 Application topology 1 57 MTG600 User Manual Trunk Gateway Network SS7 PRI Voice Internet Trunk Gateway Legacy PBX 1 2 Equipment Structure 1 2 1 Rear View AC220V0 5A E1 120 ohm ETHERNET PORTO PORT PORT2 PORTS eure ug Figure 1 2 1 MTG600 Rear View Table 1 2 1 MTG600 Rear View Description The power interface 200VAC 50 60HZ PortO Port3 E1 T1 port 2 4 E1 ports The Service Ethernet Interface standard 10 100BASE TX Ethernet interfaces Default IP address is 192 168 1 111 default subnet mask is 255 255 255 0 255 255 255 0 mo Management Ethernet Interface Default IP address is 192 168 11 1 default subnet mask is FE1 2 57 MTG600 User Manual 1 2 2 Front View li bk PAN Fe Arama 144008108 MWODEL UTS809 2E m ro 6 1 RUN ALN a t CONSOLE F
24. ask FE1 Primary DNS Fill in DNS Server IP address DNS Server Secondary DNS The secondary DNS server is option Ntoe FEO port IP and FE1 port IP should be set in different segments After configure the network address and restart the gateway configuration to take effect 2 5 PRI Config PRI configuration includes PRI parameter and PRI trunk configuration Figure 2 5 1 PRI Config PRI Config PRI Parameter PRI Trunk 15 57 2 5 1 PRI Parameter PRI Parameter Calling Party Numbering Plan Calling Party Number Type screening Indicator far Displaying Caller Number screening Indicator for Mo Displaying Caller Number Called Party Numbering Plan Called Party Number Type MTG600 User Manual Figure 2 5 2 PRI Parameter ISDN Telephony numbering plan Unknown User provide no shield User provide no shield ISDN Telephony numbering plan Unknown Information Transfer Capability Reset to default configuration PRI parameter description Calling Party Numbering Plan Calling Party Number Type Screening Indicator for Displaying Caller Number Screening Indicator for No Displaying Caller Number Called Party Numbering Plan Called Party Number Type Information Transfer Capability Save Provide six plans Unknown ISDN Telephony numbering plan data numbering plan telegraph numbering plan national standard numbering plan private numbering plan The default is ISDN T
25. ause Statistics Normal Call Clearing Call Reject User Busy 5 Normal Mo Circuit amp vailable Unassigned Number Normal Unspecified o 0 D No User Response a 0 0 0 Others Figure 2 3 6 SS7 Trunk Call Statistics The parameters of SS7 trunk call statistics are the same with PRI parameters Please refer to PRI trunk call statistics 2 3 7 SIP Call Statistics SIP Trunk Call Statistics 0 172 30 66 16 0 Figure 2 3 7 SIP Trunk Call Statistics SIP call statistics description SIP Trunk No The number of SIP trunk Trunk Name The name used to describe the PRI trunk Current Calls Number of lines that are being called currently 14 57 MTG600 User Manual 2 4 Network Network Configuration Service Ethernet Interface FEU IP Address 172 30 65 25 Subnet Mask 255 255 0 0 Default Gateway 172 30 0 1 Management Ethernet Interface FE1 IP Address 192 168 11 1 Subnet Mask 255 255 255 0 DNS Server Primary DNS Server Secondary DNS Server Save NOTE The device must restart to take effect Figure 2 4 1 Network Configuration Network Configuration IP address Set FEO port static IP address Service Ethernet Interface FEO Subnet Mask Fill in subnet mask Default Gateway Fill in default gateway Management IP address Set FE1 port static IP address Ethernet Interface Subnet Mask Fill in subnet m
26. col Type TUP or ISUP Status There are 16 status with ports each state corresponds to a color activated disable fault RAI Alarm ISDN SS7 Signal Alarm Frame Sync Idle Signal Busy L blocked R blocked B blocked Blocking Unblocking and Resetting These ports can work in many ways Select All Invert Clear Block Unblock Reset and Cancel 22 57 MTG600 User Manual 557 Circuit Maintain Operation Mode l s sr 8 se 20 2 22 23 ze 2s 26 27 28 28 30 5 ew L LLL LLL L l lil Ide Signal Busy L blo R blo B blo Block Unbl Rese Figure 2 6 8 SS7 Circuit Maintain Channel If user wants to manage the channel please select operation mode to channel Select current port use will see port status and protocol type The following will show the slot and channel status There are 16 kinds of channel states and each state corresponds to a color 23 57 2 7 R2 Config 2 7 1 R2 Param R2 Param MTG600 User Manual 0 ITU 01 A 1 A 5 A 5 I 15 I 15 A 3 Call with charge 1 Argentina 01 A 1 A 5 A 5 INVALID l 12 A 3 Call with charge 2 Brazil 01 A 1 A 5 A 5 INVALID I 15 A 3 Call with charge a China 11 A 1 A 1 A 6 INVALID I 15 A 3 Call with charge E E Czech 01 A 1 A 5 A 5 I 15 I 15 A 3 Call with charge M 5 Colombia 01 A 1 A 5 A 5 l 15 l 15 A 3 Call with charge E T Mexico 01 A 1 INVALID INVALID I 15
27. d dial rules will be saved to the local computer system logs through data backup 2 14 4 Data Restore Data Restore Database ra to Diaipan Figure 2 14 5 Data Restore 50 57 MTG600 User Manual Data restore description Database Click Browse to select the Database file and then click Restore Dial plan Click Browse to select the Dial plan file and then click Restore 2 14 5 Version Information Version Information Software 2 02 02 01 2012 04 26 09 53 16 Database 2 01 00 2012 04 23 18 53 00 Web 2 02 02 01 2012 04 25 00 01 17 Figure 2 14 6 Version Information Version information description version and built time of program database and web file 2 14 6 Firmware Upload Firmware Upload Software Web NOTE The device must restart to take effect after uploading Figure 2 14 7 Firmware Upload Firmware upload description Software Click Browse to select the firmware and then click Upload Click Browse to select the Web software and then click Upload 2 14 7 Modify Password Password Modification Old Password New Password Confirm Password Figure 2 14 8 Modify Password After entering configuration page please modify password to ensure the system security 51 57 MTG600 User Manual 2 14 8 Restart Device Device Restart Click the button below to restart the device Restart Figure 2 14 9 Restart Device If user click Restart a message
28. e in the configuration shown in the account registration If SIP trunk is under non registered mode the value is meaningless as 12 57 MTG600 User Manual Trunk Mode Peer and Access two modes Register Status Indicate the status of SIP trunk access mode register or unregister when is under peer to peer mode the values is meaningless as Link Status Established and Fault status SIP Trunk No The number of SIP trunk 2 3 5 PRI Call Statistics PRI Trunk Call Statistics Helease Cause Statistics Normal Call Clearing Call Reject User Busy Mo User Response No Circuit Available Unassigned Number c Normal Unspecified Others 0 KI 2 3 5 PRI Call Statistics description PRI call statistics description PRI Trunk No The number of PRI trunk Trunk Name The name used to describe the PRI trunk Current Calls Number of lines that are being called currently Accumulated Calls Total number of calls from running start of system to current time ASR The percent of calls completed in total calls This statistics page show the reasons for release of the call including Normal Call Clearing Call Rejected User Busy No User Response No Circuit Available Unassigned Number Normal Unspecified and others Statistical information in an intuitive would be reflected on the pie char 13 57 MTG600 User Manual 2 3 6 SS7 Trunk Call Statistics 557 Trunk Call Statistics Release C
29. e multiple SIP accounts corresponding to different trunk group ID Password Registered password Confirm Password Enter the password again Expire Time SIP registration interval default is 1800s 2 10 IP Group Config The user can group manage SIP H 323 trunk through IP packet configuration 2 10 1 IP Profile IP Profile i Declare RFC2833 Support Early Ringbac me tc Rin met ANS i ache 1 30 E FM 0 Default Yes Yes Local Local No A Fax Total 1 Page 1 Add Figure 2 10 1 IP Profile 35 57 MTG600 User Manual IP Profile Add IP Profile ID Description Declare RFC2833 in SDP Support Early Media Ringback Tone to PSTN Originated from Ringback Tone to IP Originated from Wait for RTP Packet from Peer T 30 Expanded Type in SDP EN ET ET EI mn E Reset Cancel Figure 2 10 2 IP Profile Add IP profile add IP Profile ID IP property identification number can be configured to 15 properties Description Description of the IP Profile Declare RFC2833 in SDP Default support Whether support Early Media 183 If select Yes the called side to the early Support Early Media media to provide ring back tone to the caller Ring back Tone to PSTN IP PSTN call ring back tone player side if setting to local it will play from the Originated from equipment If setting to IP it will play by the called Ring back Tone to IP Originated PSTN gt IP call ring back tone player side if settin
30. ed number KA EN User busy Line out of order Group C for Mexico Request Next ANI CHE fees est All ONES and change to Group ca mi u B E Address Complete Network Congestion Request next DNS and change back to Group A C 5 Request Last DMIS and change back to Group A Ez Figure 2 7 2 R2 Parameter Add 25 57 MTG600 User Manual Parameter Description Identification parameter group Description parameter information Points out which countries standard the parameters are CDbits C Dbit value of A B C Dbit in R2 lines of signaling Request Next The rear party notices the front party ahead called number has received and each other can DNIS send a next number The rear party notices the front party ahead callee number has received and each other can Request Next ANI send a next number Request category Means KA request code of R2 lines signaling DNIS end flag The front party notices the rear party that the called numbers send completely ANI end flag The front party notices the rear party that the callee numbers send completely The rear party notices the front party that the called and the callee numbers received Address Complete completely The general calls is free of charge or not 2 7 2 R2 Trunk R2 Trunk ul D R2 0 3 China m 4 R2 1 O ITUI A a R2 2 3 China gt Add Figure 2 7 3 R2 Trunk R Trunk Add Trunk Mo Trunk Mame El Port Mo Protocol Param Figure 2 7
31. elephony numbering plan Six optional types are provided for calling party Unknown International number National number Network special number User number Short code dialing The default option is Unknown Four options available User provider no shield User provide check and send User provide check and having failure Network provide The default option is User provider no shield Four options available User provider no shield User provide check and send User provide check and having failure Network provide The default option is User provider no shield Provide six plans Unknown ISDN Telephony numbering plan data numbering plan telegraph numbering plan national standard numbering plan private numbering plan The default is ISDN Telephony numbering plan Six optional types are provided for called party Unknown International number National number Network special number User number Short code dialing The default option is Unknown Support speech and 3 1khz audio The default option is speech 16 57 MTG600 User Manual 2 5 2 PRI Trunk Figure 2 5 3 PRI Trunk PRI Trunk Users can add delete modify PRI trunk in this configuration option Figure 2 5 4 Add PRI Trunk PRI Trunk Add Trunk Mo Trunk Mame Channel ID Protocol ISDN Alerting Indication ALERTING PRI trunk description The number of PRI trunk when user add PRI trunk 0 7 number will appear in the pull down m
32. enu to be selected the number here depends on E1 T1 physical port Trunk No number actually existed in equipment After trunk number is established filling in corresponding port number in E1 T1 Port No so as to assign E1 T1 to designated trunk Each PRI trunk corresponds to a E1 T1 port Description of PRI trunk Channel ID Channel ID of E1 T1 ports this number definition generally starts from O Indicate whether EYT1 supports D channel the default is Yes E1 T1 port number is numbered according to the physical position of E1 T1 it generally E1 T1 Port No starts from O Interface type of PRI There are two types are available ISDN and OSIG the default is Protocol ISBN Indicate PRI network property of E1 T1 it is divided into User side and Network side Switch Side When PRI loopback is carried out the network properties of E1 T1 port at both receiving and sending sides must be different Alerting Indication The ring signal include Alerting and Progress 17 57 MTG600 User Manual 2 6 SS7 Config SS7 configuration includes SS7trunk SS7 MTP Link SS7 CIC and SS7 CIC Maintain Figure 2 6 1 Add PRI Trunk 557 Config Sof Trunk oof MTP Link gt CIC E CA CA CA S7 CIC Maintain 2 6 1 SS7 Trunk Figure 2 6 2 SS7 Trunk SS7 Trunk Figure 2 6 3 SS7 Trunk Add gt 57 Trunk Add select Trunk Ma Trunk Mame Protocol Protocol Type SPC Format OPC DPC Network Indicator National Network
33. g to local it will play from the from equipment and set to PSTN it will play by the called If set to No it will auto send RTP packets during the call and if set to Yes it will Wait for RTP Packet from Peer wait the RTP packet was sent by the back side first then send out RTP packets T 30 Expanded Type in SDP T30 extended types in SDP x fax or fax 36 57 MTG600 User Manual 2 10 2 IP Group IP Group 0 66 16 Cyclic Ascending Total 1 Page 1 Figure 2 10 3 IP Group IP Group Add IP Group ID Name IP Trunk Selection Cyclic Ascending Figure 2 10 4 IP Group Add Add the IP group including the IP group ID IP group name IP trunk selection User can add a total of 16 IP group IP routing mod is to show in an IP group SIP time distribution strategy There are four options Ascending Descending Cyclic ascending Cyclic descending According to SIP trunk number to choice 2 10 3 IP Group Management IP Trunk Group 0 66 16 O SIP 0 172 30 66 16 gt 0 Default Total 1 Page 1 Figure 2 10 5 IP Trunk Group IP trunk group description Group ID IP group ID Index The priority value of 0 15 Trunk Type Currently only supports SIP H 323 will be also supported in future Trunk No SIP trunk number IP Profile ID Refer to IP Profile 37 57 MTG600 User Manual 2 11 Call Routing 2 11 1 Routing Parameter Routing Parameter Incoming Calls from IP Routing Priority First P PSTH then
34. h is 24 bits and chosen Hex OPC DPC structure format is xyz x z must be three bitts hex value y is 8 bitts hex value such as 202E 100 00000101 110 2 6 2 SS7 MTP Link Figure 2 6 4 SS7 MTP Link 557 MTP Link Figure 2 6 5 SS7 MTP Link Add gt 57 MTP Link Add Trunk No Link Ma signaling Link Code E1 T1 Port No Channel No NOTES Each 557 trunk could add maximum 2 items with different Link No 20 57 MTG600 User Manual SS7 MTP link description It is consistent with foregoing Trunk No of SS7 trunk Equipment maximum support 2 signaling links these two links share workload when Link No one link fails the other link will take over the load until restore from failure and then they will share the load again If a signaling point has established several signaling links then the code of each signaling Signaling Link Code link will begin from O Indicate which E1 T1 this link is established on it is stipulated that such numbering is E1 T1 Port No carried out according to the physical position of E1 T1 Indicate time slot that link is established on It is assigned to 1 or 16 for time slot the Channel No default is 16 time slot 2 6 3 SS7 Circuit Figure 2 6 5 SS7 Circuit 557 Circuit Figure 2 6 6 SS7 Circuit description gt 57 Circuit Add Trunk No E1 T1 port No start Channel Start CIC No Count NOTES 1 When option ITU or TTU CHINA has been selected in
35. he limitation on the number of calls the range is 0765535 the IP to PSTN Calls default is no limitation If Yes is selected then input limitation number of calls in the Restriction edit box appeared PSTN to IP side of the limitation on the number of calls the range is 0765535 the PSTN to IP Calls default is no limitation If Yes is selected then input limitation number of calls in the Restriction edit box appeared The default setting is disabled If Enabled is selected then user can edit the start IP to PSTN Time and stop time of prohibition time interval Within this time interval all calls from IP Restriction to PSTN are prohibited Calls from PSTN to IP are not limited Detect the status of SIP trunk If select it the equipment will send HEARTBEAT Detect Trunk Status message to peer to make sure the link status is OK A switch used to enable this SIP trunk or not user can select Yes or No Enable SIP Trunk when No is selected this SIP trunk is invalid 2 9 3 SIP Account SIP Account Figure 2 9 4 SIP Account 34 57 MTG600 User Manual SIP Account Add SIP Account ID Description Binding PSTN Group SIP Trunk No Username Password Confirm Password Expire Time Figure 2 9 5 SIP Account Add This option is when the equipment is in the registered mode used to manage SIP trunk account SIP trunk account Username SIP registration user name the same SIP trunk can configur
36. igure 1 2 2 MTG600 Front View Table 1 2 2 MTG600 Front View Description Off Power is off Power is on Slow blinking Unregister Fast blinking Register The failure of device Off Normal Yellow indicator Failed ES Reset button it is used to restart the device RS232 console port it can be used to debug and configure the device The baud rate is 115200 CONSOLE ps Indicating the connection On E1 T1 port connection and sending receiving state of device EYT1 message normal Flash E1 T1 port connection failed Off Network connection failed DNE Indicating the connection Off E1 T1 port connection normal E1 T1 On Network connection normal and O indicates FEO state of the network and 1 indicates FE1 Indicating the network Off 10Mbps bandwidth SPEED bandwidth On 100Mbps bandwidth 3 57 1 2 3 RJ 48c Line sequence RJ A8 Pin on T1 E1 PIC RJ48 Pin Data numbering form Data numbering form Ro oo un MTG600 trunk gateway adopts standard RJ 48C interface and impedance value is 120Q Connected end device by cross lines sequence 1 3 Functions and Features 1 3 1 Protocol standard supported e Standard SIP PRI protocol e NAT Traversing STUN e Hypertext Transfer Protocol HTTP e Domain Name System DNS e ITU T G 711A Law U Law G 723 1 G 729AB iLBC optional 1 3 2 System Function e Comfort Noise Generation CNG e Voice Activity Detection VAD e Adaptive Dynamic Jitter B
37. is caused by the unframed nature of the all ones signal is declared The AIS failure is cleared when the Loss Of Frame failure is cleared 4 Disable Means that this E1 T1 is not used 5 ISDN SS7 Signal Alarm Means physical connection is normal signaling link has problem 6 Active OK Means that physical connection and signaling link are normal Frame Sync Non voice channel which used as a synchronization channel Idle Means this channel is idle when the channel is enabled and the cable is connected OK 3 Signal Signal channel 4 Busy Means this channel is occupied by voice E1 T1Channel Status 5 Fault The channel is enabled but the cable is not connected 6 Disable Have not use this E1 T1 trunk 7 L blocked Local blocked means that communication can only be initiated from local 8 R blocked 11 57 MTG600 User Manual Remote blocked means that communication can only be initiated from remote 9 B blocked Both Sides blocked means that the two sides cannot communication 2 3 3 PSTN Trunk Status PRI Link 5tatus 557 Link Status Figure 2 3 3 PSTN Trunk Status PSTN trunk status description 1 PRILink Status 2 SS7 Link Status 2 3 4 IP Trunk Status SIP Trunk Status 0 172 30 66 16 Feer IP Address Established Figure 2 3 4 SIP Trunk Status IP trunk status SIP Trunk No The number of SIP trunk Username When SIP trunk is under registered mode change the valu
38. ix number Is a wildcard representing any caller number 2 11 3 PSTN gt PSTN Routing Figure 2 11 4 PSTN gt PSTN Routing PSTN PSTN Routing Total 0 gt Add Figure 2 11 5 PSTN gt PSTN Add 39 57 MTG600 User Manual Route PSTN PSTN Add Index Description Source Type G FSTN Group Callee Prefix Caller Prefix Destination Type Destination PSTN Group Ress NOTE in Callee Prefix or Caller Prei field means wildcard string PSTN gt PSTN Routing Routing Call from PSTN to PSTN PSTN gt PSTN Routing Routing index number 0 255 PSTN gt IP Routing priority rule is according to the index to set Reference dial plan Description Describe the routing Source Type Source type is PSTN group or PRI SS7 trunk PSTN Group Refer to PSTN Group Config any means any trunk group PSTN Trunk Reference PRI Trunk or SS7 Trunk Callee Prefix Callee number matches prefix number Is a wildcard representing any callee number Caller Prefix Caller number matches prefix number Is a wildcard representing any caller number Destination Type Destination type is PSTN group or SIP H 323 trunk Destination PSTN Group Refer to PSTN Group Config 2 11 4 IP gt PSTN Routing Figure 2 11 6 IP gt PSTN Routing IP PSTN Routing 3 Jescriptior n i Trunk No IP Gre Callee Prefix Calle eT ze id Fl 255 all Any Any 0 66 1 l i 0 lt r2 0 gt Total 1 Figure
39. lease firsthy slelect Group Trap Configuration TrapFlag Trapif TrapPort TrapCiomrmunity it oi p oo Figure 2 14 3 SNMP Parameter SNMP Parameter description Community Configuration Community The name of network management server managed equipment Source Network management server address Group Configuration Name of community group different versions can use a same group name Community join the group View Configuration The name of description mib tree View type There are Included and excluded options 49 57 MTG600 User Manual Displayed OID of access parameters View mask The same with equipment subnet mask Generally don t configure Trap Configuration Trap Flag Version of SNMP Device to inform the NM server s IP address The IP can be configured the same with source IP in community also be different Trap Port Default service port is 162 Trap Community The same with community in community configuration Note After configuration please restart equipment to take effect Users can manage and configure gateway on remote NM server through SNMP configuration But in order to security recommend this option to open when needed 2 14 3 Data Backup Data Backup Click Backup to download database file to your computer Click Backup to download dialplan file to your computer Click Backup to download exception file to your computer Figure 2 14 4 Data Backup Database an
40. on mode and at most can add up to 16 set of data Channel selection mode refers to E1 T1 timeslot allocation strategy in a trunk group There are four options Ascending Descending Cyclic Ascending and Cyclic Descending for routing 2 8 7 PSTN Group Management PSTN Group Management 0 r2 0 gt 0 0 1 31 0 Default 0 lt r2 0 gt 1 2 0 Default Total 2 Page 1 Figure 2 8 11 PSTN Group Management PSTN Group Management Add Group ID Start E1 End E1 Start Channel End Channel PSTN Profile ID 0 Default EN E1 cance Figure 2 8 12 PSTN Group Management Add PSTN group management add Group ID PSTN group ID Start E1 E1 T1 trunk group port number in the initial End E1 Last a E1 T1 trunk group port number Start Channel The beginning of time slot assigned a precise time slot for a group of trunk End Channel The end of time slot assigned a precise time slot for a group of trunk PSTN Profile ID Refer to PSTN Profile 32 57 MTG600 User Manual When cross E1 port operation don t choose start termination of the time 2 9 SIP Config 2 9 1 SIP Parameter SIP Parameter Local SIP Port Local Domain Figure 2 9 1 SIP Parameter The default Local SIP Port is 5060 and Local Domain set here can replace SIP account 2 9 2 SIP Trunk SIP Trunk 0 172 30 66 16 172 30 66 16 5060 Disable Disable Request line No Peer IP Address Yes Yes Total 1 Page 1 w Figure 2 9 2
41. r Management parameter description Primary NTP server The Primary IP address of SNMP management host computer The host computer Address of the IP address will carry out monitoring and management to equipment Primary NTP server Port The port that managed device provides trap message it is generally alarm message to SNMP management host computer the default is 123 Secondary NTP server The Secondary IP address of SNMP Address Sync Interval Time interval of check Time Zone The time zone of local 48 57 MTG600 User Manual 2 14 2 SNMP Parameter Simple Network Management Protocol SNMP is application layer protocol and used to manage communication line This equipment supported three versions V1 V2C and V3 In addition to V3 version the other two versions do not support encryption However the service is usually located on the edge of the network devices security risk it is best to disable to be used again SNMP Parameter SNMP Enable e Yes No SNMP Version Community Configuration Community Source Motice default value of source is default if other valve please input IPliag 182 183 1 1 Group Configuration Community View Configuration Mesi s me View Su ViewMask mduded E Notice ViewSubtree style x x x x x if just one style x Access Configuration v1 v2c Group Read Write ts ad x im L l ard Notce Read rite Notify value refrence ta ViewName lf Read VWrite Motify want to have value p
42. rder to ensure each rule can take effect long matching numbers prefix rule dial plan index value need smaller 2 Maximum length is 30 this value is the number of the total length and including the prefix length Click Add to add dial plan configuration page as follow Dial Plan Add Dial Plan ID Index Prefix Min Length Max Length NOTES 1 in Prefix field means wildcard string 2 Max Length and Min Length do not include the prefix 3 The value of Max Length plusing the length of Prefix should less than 30 Figure 2 8 4 Dial Plan Add Dial Plan description Dial Plan ID The number to identify a dial plan Dial plan priority rules take effect in accordance with dial plan index size and not Index according to the maximum number received Prefix Match number representative of any number The minimum receiving Number length O to 30 If receiving a number equal to the minimum length greater than less than equal to the maximum length the number will be used to continue the call If the maximum length determine the number to receive a Min Length complete will no longer receive a new number and immediately began to number analysis If there are numbers continue to be received the system will give up these numbers Max Length The largest received number length 0 to 30 special version 1 Dial plan can be backup and restore in management configuration 2 Min Length
43. uffer DJB e DTMF mode RFC 2833 SIP INFO and INBAND e T 38 Pass Through FAX over IP e HTTP Telnet configuration e Firmware upgrade by TFTP Web 1 3 3 Industrial standards supported e Stationary use environment EN 300 019 Class 3 1 4 57 MTG600 User Manual No connect No connect e Storage environment EN 300 019 Class 1 2 e Transportation environment EN 300 019 Class 2 3 e Acoustic noise EN 300 753 e CE EMC directive 2004 108 EC e EN55022 2006 A1 2007 e EN61000 3 2 2006 e EN61000 3 3 1995 A1 2001 A2 2005 e EN55024 1998 A1 2001 A2 2003 e Certifications FCC CE 1 3 4 General hardware specification e Power supply 220VAC 1 2A e Temperature 0740 C operational 20 70 C storage e Humidity 102679025 no condensation e Max power consumption 10W e Dimension mm 330 200 44 e Net Weight 1 29 kg 5 57 MTG600 User Manual MTG600 User Manual 2 Parameter Setting 2 1 Login First device FEO port connect PC with string and then fill FEO IP address in browser FEO default IP address is 192 168 1 111 It will request customer to input user name and password Default user name and password are admin If customer modified the default IP or forgot the IP that can t enter the configuration page Please connect PC and device serial with the serial line Enter the CLI to view or modify the equipment IP Here IP is set to 172 16 99 120 In addition hold down the RST button to restart the
44. utbound calling called number Notes 1 The more precise configuration index values should be smaller 2 Suggesting configure Any and avoid missing the call for the replace number 3 When configuring data it is suggested that index starts from large index value to avoid adding an exact match data not directly use the data 4 When configuring data it is suggested that keep using index value 42 57 2 12 1 PSTN gt IP Callee MTG600 User Manual PSTN IP Callee Add Index Description FSTN Group Callee Prefix Caller Prefix PSTN gt IP Callee Total 0 gt Ma De ran Figure 2 12 2 PSTN gt IP Callee Number of Digits to Strip from Left Number of Digits to Strip from Right Prefix to Be Added Suffix to Be Added Number of Digits to Reserve from Right NOTES 1 Fields with are MUST 2 in Callee Prefix or Caller Prefix field means wildcard string Figure 2 12 3 PSTN gt IP Callee Add PSTN gt IP Callee Replace the called number from PSTN PSTN gt IP destination number Index Description PSTN Group Callee Prefix Caller Prefix Number of Digits to Strip from left Number of Digits to Strip from right Prefix to be Add Suffix to be Add Number of Digits to Reserve from Right Index number 0 127 Describe the transformation of the number Refer to PSTN Group any means any trunk group Called number prefix mean any called number
Download Pdf Manuals
Related Search