PulseIR User Manual for Linux OS
Contents
1. 02 00 0 17i nput 0 at ai al ol ile a te Sy sf s devi ces pci 0000 00 0000 00 11 0 0000 02 00 O usb2 2 1 2 1 1 O i nput i n tat Baa Pt E F ao er F ent Tal inl ni q Hand er sarousel event4 A l KEY 403 0 fO003 O O00 ABS 7f 00 3f ae Installation of Utility program Copy a utility program for Linux OS pulseirConfig linux version tgz from installation CD or download link to a directory Then Install the program by following the steps below Step 1 Decompress PulselR utility Decompress the compressed utility program by executing the Linux terminal command as follows tar xvzf pulseirConfig linux version tgz in the directory copied the utility program Step 2 Run PulselR utility program amp Admin privilege is required to execute the terminal command to install PulselR utility program Connect the touch device to a USB connector in Linux computer Execute Linux terminal command to run PulselR utility program pulseirConfig Then PulselR utility program is displayed as shown in the below figure pulseirConfig Parameter Setting Touch ON OFF On OFF Touch Mode Auto O Stylus O Mouse Mouse R Click Long Down Disable Rotation w 0 O 90 iO 180 O 270 Touch Object Size mm lo min lo Imax if 0 gt disable Click Point Correction Rimm lo Use Mouse Over Delay Poe tan Specd UplhAmbient Ski C Drawing Speed Up Ambient Skip Default Setting Calibration Touc2. PulselR User Manual for Linux OS Quick Start User Manual for Linux OS PULSEIR CY Installation PulselR Touch System Utility Installation PulselR system is a plug and play HID USB Device which automatically manages device drivers eliminating any manual installation or upgrading of the drivers ib Upon connection to a USB port PulselR system initializes DO NOT touch the screen while the new device found message box displays for approximately 3 seconds Following versions of Linux systems have been tested for compatibility Kernel 2 6 35 or later version GNOME 2 28 or later version Redhat 6 0 or later version Ubuntu 8 10 or later version Debian 5 04 or later version Fedora 12 or later version JAVA 1 6 or higher version must be installed In addition most Linux kernel that supports HID device will work properly Installation of PulselR utility program Default Operation PulselR system is a plug and play HID USB Device which automatically manages device drivers eliminating any manual installation or upgrading of the drivers Connect the PulselR touch unit to a USB connector in Linux computer and type it in the terminal command mode as follows cat proc bus input device If you can see the device information as shown in the red box on the following figure the touch device is ready to use Bus 0003 Vendor 10f 0 Fr oduct 5003 Versi on 0110 Nare RNOPLUS Co LTD PULSEIR DT 42i nch Phy s usb 0000
3. h Area Setting Apply Close Touch Action Drawing 2 Touch Only Using PulselR Utility Pogram Selecting Apply button will save new settings to the controller Selecting Default button will return controller settings to factory default values Touch On Off This function enables and disables the touch detection for special testing and set up needs Touch Mode Mode Purpose Auto Automatic OS Detection for OS running Windows Linux Mac Stylus Supports stylus operation in Android OS Multi touch operation in Linux Mouse Single Point Mouse mode Mouse R Click Apply only in Mouse Mode Setting Effect Long Down extended touch triggers the Mouse R Click event Disable do not support Mouse R Click event Touch Action Apply only in Mouse Mode Setting Effect Drawing Touch and Drawing support Touch Only For simple touch detection only No continuous tracing for drawing and scripting Touch Rotation For special mounting configuration relative to display orientation If the touch screen is attached to the display in normal orientation the rotation of the display is controlled by Windows Display Setting dialog box Select a desired Orientation for display placement and the touch screen will automatically adjust Touch Object Size This function controls the size of object to have the touch detected The only object the size is between Min and Max is able to be detected If both of Min and Max are set to 0
4. minal command to run pulseirTuioServer program for the multi touch operation tar xvzf PulselRTuioServer linux x x x tgz and locate and execute PulselRTuioServer by using the terminal command Warning Connect the touch screen to the PC before launching this application Usage pulseirT uioServer option host port host hostname or ip address default 127 0 0 1 port port number default 3333 option d mouse report disable h print this message
5. this feature is disabled Click Point Correction R This function compensates the touch error which may be happened by inaccurate touch The radius of touch point should be set to activate this feature Use Mouse Over Delay This function is supported in only Mouse touch mode Check this to apply Time Delay when touching down a menu button Drawing Speed Up Ambient Skip This function increases the drawing speed by 1 1 5 times more than the normal speed This function is recommended to use under the environment of no or weak ambient light Calibration button launches a program for manual calibration when an offset is required To compensate for misalignment between the touch screen and the display launch this program and touch the 4 points as they are presented A Touch Area button launches a program for selecting touch sensitive area To limit touch detection to only a selected area drag a box from top left to bottom right of the area on the touch screen Touch will not be detected outside of this area Multi Touch Operation Run TUIO Interface Utility Program for Linux OS Run TUIO multi touch interface utility program to use the touch device for the multi touch operation If you do not have PulselR TUIO Interface utility for Linux OS please download this program and Extract the pulseirT uioServer linux version tgz tar file by using terminal command Admin privilege is required to execute the ter
Download Pdf Manuals
Related Search