Operating Instructions
Contents
1. The pipe entry point is elevated to prevent water ingress This can be sealed if required Rinnai 2 Smartbox SBOX I SBOXC SBOXF The Rinnai water heater serial and model numbers on the data plate located on the left hand side of the appliance MUST BE copied to the sticker on the inside of the Smartbox cover The serial and model IMPORTANT numbers are required for future service work 5 Remove the two M5 Nyloc nuts from the fixing studs of the insert 6 Insert the upper mounting bracket of the Rinnai water heater into the bracket slot located at the top of the insert 7 Push the appliance up until the lower mounting bracket aligns with the fixing studs and secure in place with the two M5 Nyloc nuts removed in step 5 8 Connect the Rinnai water heater in accordance with the Operation Installation manual supplied with the water heater 9 An approved weatherproof electrical GPO can be fitted on either side inside the insert in accordance with AS 3000 Wiring Rules 10 Commission and test the water heater in accordance with the Operation Installation manual supplied with the water heater 11 Attach the warning sticker that is supplied with these instructions to the front cover of the Rinnai water heater 12 Install the Smartbox cover by aligning it with the Smartbox insert the flue spigot hole is to be uppermost and push into place ensuring that the 4 locking clips have engaged securely DIMENSIONS Be i es2. 2 location complies with the requirements of AS 5601 Fig 5 3 2 When installing the SBOXF frame it should be orientated so that the sealing flange is against the wall surface and the two drainage slots are in the lower most position SECURING OPTIONS The Smartbox Frame and Insert are designed for surface mounting and may be secured using any of the methods described below Securing SBOXI SBOXF externally Use the 8 x 100mm bugle screws that are supplied with the SBOXF frame to secure both the SBOXF frame and SBOXI insert to the wall surface When securing the SBOXI Insert and SBOXF frame from the front use ONLY the 8 screw holes a that are provided DO NOT attempt to screw or nail through the sealing flange of the SBOXF frame IMPORTANT aS this may damage the frame Securing SBOXI SBO F internally through the side wall Secure the SBOXI insert into a solid fixture such as brickwork timber studs etc through the side walls using suitable fasteners Securing SBOXI SBOX F internally through the rear wall Install noggins between wall studs and secure through the rear wall of the SBOXI insert using suitable fasteners Securing SBOXI SBOXF with the use of brick ties Secure a brick tie to the side walls of the SBOXI insert with pop rivets or screws Rinnai Australia Pty Ltd asn 74 005 138 769 Internet www rinnai com au E mail enquiry rinnai com au Head Office National
3. Help Lines 10 11 Walker Street Tel 03 9271 6625 Spare Parts amp Technical Info Braeside Victoria 3195 Fax 03 9271 6622 Tel 1300 366 388 Fax 1300 300 141 PO Box 460 Cost of a local call Higher from mobile or public phones Hot Water Service Line Tel 1800 000 340 Rinnai 4 Smartbox SBOXI SBOXC SBOXF 04 114 Issue 2 29 01 10
4. The Smartbox recess enclosure system is made up of two 2 components these are the SBOXI insert and SBOXC cover Both items are packaged and purchased separately 2BOXC S S sB 0x Take care to AVOID exposing Smartbox If you DO NOT have a SBOXC cover for your Components to ANY EXCESSIVE HEAT when Smatbox contact your supplier welding pipes Obstruct the slots provided for the Cover Clips Support Bracket or Pipe Access Support ea Bracket Slot Pipe Access eq Slot Oo m O N m e o N N m N q So r Oo m v lt o Securing Method Q Securing the Smartbox Securing the Smart f Securing the Smart f Securing the Smart Insert externally Box Insert internally Box Insert internally Box Insert with the use through the side wall through the rear wall of brick ties REFER TO THE FOLLOWING INSTALLATION INSTRUCTIONS FOR FULL INSTALLATION DETAILS Rinnai 1 Smartbox SBOXI SBOXC SBOXF amp To suit the following Rinnai water heater models REU V2626WG INFINITY 26 REU VM2630WD INFINITY 26 Plus REU VM2630WC HD 200e Smartbox Recess Enclosure SBOXI SBOXC iris RELI 17 REU V2426WB V1500 Installation Instructions R N Smartbox RECESS ENCLOSURE COMPONENTS SBOXI insert and SBOXC cover packaged and purchased separately GENERAL PREPERATION 1 Prepare an opening in the wall approximately 1 metre above the ground The opening
5. he noggins through the rear wall using suitable fasteners Securing the Smartbox Insert with the use of a brick tie Secure a brick tie to the side walls of the insert with pop rivets or screws As the brickwork is being laid use the attached brick ties to secure the insert into the brick courses Use two brick ties per side one near the top and bottom of the insert VSS N Installing the Smartbox to rendered surfaces Use spacers not provided to install the Smartbox insert with sufficient clearance for rendering FLANGE ala When the render is applied ensure that the gap provided by BRICK the stand off spacers is NOT exceeded as this will prevent the TOP VIEW A Smartbox cover from being fitted ASSEMBLY AND APPLIANCE INSTALLATION THE SMARTBOX COVER AND INSERT ARE CONSTRUCTED FROM DURABLE ABS PLASTIC NEVERTHELESS TAKE CARE WHEN WELDING ANY PLUMBING CONNECTIONS TO ENSURE NO CAUTION SMARTBOX PARTS ARE SUBJECTED TO A NAKED FLAME OR EXCESSIVE HEAT THE SMARTBOX IS NOT SUITABLE FOR INSTALLATION INTO WALLS WHICH ARE REQUIRED TO BE FIRE RESISTING AS DEFINED IN THE BUILDING CODE OF AUSTRALIA BCA UNLESS ALTERNATIVE PROVISIONS ARE MADE TO ACHIEVE THE REQUIRED FIRE RESISTANCE LEVEL FRL REFER TO THE BCA FOR MORE INFORMATION FRONT VIEW TOP VIEW 4 The gas cold water inlet and hot water outlet pipes can be brought through the pipe entry point at the base of the insert
6. requirements are Height 1030mm Width 390mm and a minimum Depth of 160mm see dimension diagrams page 2 Ensure the location complies with the requirements of AS 5601 Fig 5 3 2 Remove the transport tab from the pipe entry point of the insert 3 Determine the appropriate electrical access point and remove either the left or right the knock out plug located near the bottom of the side walls of the insert SECURING OPTIONS The Smartbox insert is designed to be surface mounted and may be secured using one of the following methods Securing the Smartbox Insert externally Secure to the wall surface via the 8 screw holes provided in the flange of the insert using suitable fasteners 7 125 f gt gt Securing the Smartbox Insert internally through the side wall Secure the insert into a solid fixture such as brickwork timber studs etc through the side walls using suitable fasteners The excess space between the side walls of the insert and the solid fixture may require packing to prevent distortion of the NOTE insert At least two fasteners should be used through each side wall approximately 125 mm from the inside top and bottom horizontal faces of the insert gt 125 Securing the Smartbox Insert internally through the rear wall Install two noggins between wall studs these are to be centred at 130 mm from the top and bottom of the opening Secure the insert into t
7. te tee 3 rie oes amp Fo s o d e Ls A tates i 7 7G 7 ee es G 7 ws D D T es Width 390 1086 Centre of noggin VD OPENING Smartbox INSERT SBOXI Smartbox COVER SBOXC ALL MEASUREMENTS ARE IN MM UNLESS OTHERWISE STATED Rinnai 3 Smartbox SBOXI SBOXC SBOXF To be used in conjunction with Smartbox Recess Enclosure Insert SBOXI Smartbox Recess Enclosure Cover SBOXC Smartbox Semi Recess Frame SBOXF Installation Instructions Smartbox SEMI RECESS FRAME USE The SBOXF Frame is used when a semi recessed installation of SBOXF the Smartbox recess enclosure is required SBOXF reduces the cavity depth requirements of the SBOXI Insert by 60mm This is useful where the depth of a wall cavity is insufficient to allow SBOXI to be fully recessed for example weatherboard or other non masonry walls SBOXF The Smartbox Frame SBOXF is to be installed at the same time as the Smartbox Insert SBOXI and NOTE Smartbox Cover SBOXC These instructions are to be followed in conjunction with the Installation Instructions for Insert and Cover supplied with those items GENERAL PREPERATION 1 Prepare an opening in the wall approximately 1 metre above the ground The opening requirements are Height 1030mm Bra Width 390mm and a minimum Depth of 100mm Ensure the
Download Pdf Manuals
Related Search