IP 코덱 사용 설명서
Contents
1. 2 3 Audio Setup Live View Change User System Video Audio Network Serial Event Preset User Camera Audio Mode Mode T only Tx amp Rx Input Gain Input Gain gt 25 a E Mode Select audio operation mode Mode Action Off No operation Tx Only Transmit only Rx Only Receive only Tx amp Rx Transmit and Receive W Input Gain Set audio input gain 18 2 4 Network Setup Live View Change User System Video Audio Network Serial Event Preset User Camera Network Local IP Mode Fixed IP Local IP 192 168 10 236 Local Gateway 192 168 10 1 Local Subnet 255 255 255 0 DNS Obtain DNS server address automatically Use the following DNS server addresses Primary DNS Server 164 124 101 2 Secondary DNS Server 168 126 63 2 Port Base 2222 HTTP Port 80 RTSP 554 RTSP Authentication RTSP Authentication Off O On SNMP SNMP Listen port 0 SNMP Trap Destination IP 255 255 255 255 SNMP Trap Destination Port D Multicast Multicast IP 224 10 0 0 DDNS DDNS Server None TrueDNS DynDNS ID Password Domain Name Address Information Current IP VC58SM User Manual 192 168 10 236 Current Domain Not RegisteredB MAC Address 00 1 63 5 00 4 19 VC58SM User Manual E Mode Two IP modes are supported Depending on t2. VC58SM User Manual 3 System Operation 1 Remote Video Monitoring There are two ways to monitor video when the decoder site and VC58SM are connected IP address should be correct please refer to True Manager Manual and Remote Setting in Chapter 5 for further details Default ID admin Password 1234 E Video Monitoring via Decoder System Once the VC58SM s IP address is set in the remote IP address section of the decoder the decoder system will connect to the VC58SM and start receiving the video images Normally a monitor connected to the decoder will display video images E Video Monitoring by Internet Explorer If VC58SM s IP address is entered in to Internet Explorer the system will ask for confirmation to install Active X control Once authorized Internet Explorer will start to display video images from the encoder as shown below http 192 168 10 100 Live View Setup Change User Video Server Video Select Primary Secondary View Size 5 1 lt gt cl E SelectPreset 30 Sensor input Alarm output Snapshot Talk OOn B Video Selection VC58SM User Manual If Primary is selected 1920 x 1080 via H 264 compression algorithm video can be displayed And once activated Dual Video compression and Secondary may be selected Max D1 resolution via H 264 or MJPEG compression algorithm video can be displayed in t
3. VC58SM User Manual http ns1 truecam net System will get a domain name of xxx truecam net style Refer to the user guide document for True DNS service DynDNS use DynDNS service Refer www dyndns org for details W Address Information Tree addresses are checked by 3 ways below Read only IP Address The servers own IP address This information is useful when the server s IP mode is set to DHCP Domain Name In case the server is registered with DDNS server the registered domain name is displayed MAC Address Display the MAC address of the server In case the server is registered with DDNS server the MAC address is used in DDNS registration 21 2 5 Serial Port Configuration VC58SM User Manual Setup Live View Change User System Video Audio Network Serial Event Preset User Camera Serial Apply COM 2 RS 485 Port Protocol Bitrate 2400bps Data Bit Bits Parity None v Stop Bit 1Bits PTZ None PTZID 1 1 PTZ Direct Keyboard Control O Sensor Type Sensor O off 9 ONIC Sensor Schedule Select Sensor Sensor 1 0121314 1516 7 8 9 101112131415161718192021 2223 SUN SPEER HERE EEE Ree TE TH Fl E Serial
4. Network Camera VC58SM User Manual VC58SM User Manual Safety Precaution We appreciate your purchasing series Before installing the product please read the following with care Make sure to turn off the power before installing VC58SM Do not install under the direct sunlight or in dusty areas Make sure you use the product within the temperature and humidity specified in the specification Do not operate the product in the places with vibration or strong magnetic fields Do not put electrically conductive materials into the product unless specified in the manual Do not open the top cover of the product It can cause an static shock and damage the components In order to prevent overheating make sure there is at least 10 cm of space between the wall and the product After checking rated voltage please connect the power VC58SM User Manual Table of contents 1 About User MArtilal z 22 22 22 31 Lege eed E Dee EP o ERN ENSE HORE 3 2 8 EET 3 3 Product and ACC6SSOTFIeS oic S ER PER EE PER ERE RET RR PLUR Ee Yrs 4 a Product OVEIVIGWEsssoseteseie iara aeg at ates siti QF 5215 SAHA UA Sud 5 SYSTEM iss tats cess SER twa Rep A 6 Zac 8 1 Connecting NetWork LAN 2435s et khoa PEU F
5. DAY NIGHT MODE AUTO COLOR B W AUTO The image displays Color at daytime and automatically turns to B W mode at nighttime Darkness Lux level is adjustable Day Night filter is automatically switched and off at the designated lux level COLOR The image displays Color all the time B W The image displays B W all the time E AWB MODE AUTO PUSH USER Selectable AUTO PUSH USER AUTO It is generally used It is suitable for viewing a scene with one or various colors mixed on the background PUSH It is suitable when the object s background is in high color temperature Ex Clear sky Sunset B AUTO EXPOSURE IRIS DC ESC To select DC lris lens or Manual lris lens When DC lris lens is used the menu should be set to DC condition BRIGHTNESS 00 50 Brightness is adjustable from 00 50 Default 25 FLICKERLESS ON OFF This is used only when there is a difference in frequency between the power system 50Hz and TV system 60Hz In this case flicker is occurred on the monitor Backlight Function Back Light Compensation When images taken under backlight are played on monitor background is bright saturated by white subject is dark The function is to prevent the subject from being unidentifiable m EFFECT SHARPNESS 00 15 To set up the sharpness level of the picture Adjustable between 00 15 Default is 8 REVERSAL NOR MIR VER FLIP NOR Normal image MIR
6. MOTION DETECTION Motion Detection Use Motion Detection Off On SERRE SEE 1 it Enabl Disabl Edit Enable Disable Apply Edited Area Mode O Set Erase Sensitivity 0 for most sensitive 5 Use Motion Detection Select Motion Detection function B Motion Detection Area Editing Configure regions for motion detection Regions of arbitrary shape can be configured by the following steps Enable Edit item Select editing Mode Set is for including cells to motion detection region and Erase is for excluding G Select cells using the left button of the mouse Multiple cells can be selected conveniently by press and dragging 17 VC58SM User Manual Press Apply Edited Area button to save the editing E Sensitivity A condition to trigger an event of motion detection The value determines the sensitivity of the motion detection within a block the smaller the more sensitive It is selectable from from 0 to 10 W information Display System ID and or server time can be display over the video window in Web View Each item can be turn on or off and position can be configure as well This information is displayed after the video is decompressed E Burn in OSD Insert system ID and date time in the compressed video System ID and time respectively can be turned on or off in the video And position and Font size can be selectable
7. Mirror image E VER Vertical Reversal image FLIP over image Es 31 gt VC58SM User Manual Model VC58SM Network Interface Ethernet 10 100Base T RJ 45 Network Network Protocol TCP IP UDP Multicast DHCP SMTP HTTP SNMP RTP RTSP Image Device Sony 1 3 1 3M CMOS Progressive Scan Lens C CS Mount lens Mechanical Iris Lens DC Iris Lens MIN 1 0 Lux without DSS F1 2 30IRE AGC ON Iris Auto Manual Shutter Speed 1 30s Default Long Exposure Mode 1sec AGC Normal High Off BLC On Off Flickerless Disable 50Hz 60Hz Selectable Backlight Function On Off Camera Brightness 0 50 Adjustable MAX AGC Gain 0 50 adjustable Day amp Night On Off Night gt Day 0 50 Adjustable Transition Day gt Night 0 50 Adjustable Transition AWB Mode ATW Mode PUSH Mode Manual Mode R Gain 0 50 Adjustable B Gain 0 50 Adjustable Primary H 264 Algorithm Secondary H 264 M JPEG Simultaneous Dual 1280 x1024 1280 x 960 1024 x 768 800 x 600 640 x 480 352 x 288 Resolution 352 x 576 720 x 288 720 x 576 352 x 240 352 x 480 720x 240 Video 720 x 480 13 Resolution Mode Selectable Frame Rate 1 FPS 30 FPS Selectable Bit Rate 30K BPS 8M BPS Selectable Output Composite 1 EA Algorithm G 711u Sample Rate 8KHz Audio Bi
8. Configure the actions when the link connection with peer system is disconnected Multiple actions can be set for a single event E Alarm activation duration Set the duration of alarm activation in case of an event If it is set to continuous it will be in active state until an operator reset it manually E mail Notification Specify the information to send E mail as the action of an event The address of mail SMTP server needs to be specified on Server Address field and Port specifies the port for SMTP operation Port 25 is the default port in SMTP operation If a different port is configured in the SMTP server this port needs 25 VC58SM User Manual to be changed accordingly When the server requires authentication ID and password of an E mail account needs to be entered also Destination address needs to be entered on Destination Address field More than one address can be entered by delimiting comma or semi colon Destination address can take up to 63 characters Video clip of AVI file format or JPEG file at the moment of the event can be attached by setting Video Clip Attaching FTP Upload Specify the information for uploading a video file as the action of an event The address of an FTP server to receive video files is specified on Server Address field and Port specifies the port for FTP operation Port 21 is the default port in FTP operation If different port is configured in the FTP server thi
9. number of frames of video images to compress The frame rate actually transmitted can be affected by the network bandwidth limitations E Preference Preference in video compression and transmission With Bitrate selected the video compression will be effected by the Bitrate value entered With Quality selected the video compression will be effected by the quality of image selected Therefore Bitrate and Quality corresponds to CBR Constant Bitrate and VBR Variable Bitrate respectively E Quality VBR Variable Bit Rate adjusts the bit rate according to the image complexity using up bandwidth for increased activity in the image and less for lower activity in the monitored area E Bitrate CBR Constant Bit Rate allows you to set a fixed target bit rate that consumes a predictable amount of bandwidth As the bit rate would usually need to be increased for increased image activity but in this case it is constrained the frame rate and image quality are affected negatively E Frame Interval Setting numbers of P frames to each frame between 0 and 255 16 VC58SM User Manual There will be no P frame if O is set DUAL ENCODE Use Dual Encode Select On to use dual encode E Dual Encode Algorithm H 264 and MJPEG can be selected for secondary streaming Maximum resolution is 720 x 480 and there are 8 steps of resolution If MJPEG is selected Preference supports only Quality mode
10. 720x48 Framerate Quality Ultra fine Bitrate 1 kbps 32 1024 c 255 Frame Interval Motion Detection Use Motion Detection Of On Disable Erase Edit Enable Mode Set Sensitivity 0 for most sensitive m 24 a Information Display SystemID Off On Time 9 Off O On Position Bottom Top Burnin OSD SystemID Off On Time Off On Position Bottom 9 Top Font Size Small 8x8 Middle 16x16 Large 32x32 15 Change User Camera VC58SM User Manual ENCODE W Enable Preview Turn on to transmit the video direct to HD monitor and select the one of Output Formats in the end of the Video setting section Scaling If the encoding resolution was different from the input resolution encoding video was cropped In the scale mode whole visual region of input source will be encoded even when the encoding resolution is smaller than the input video resolution However if the aspect ratio of of the encoding resolution is different from the input resolution distortion can be seen Also it is possible that the quality of video will deteriorate during the process of scaling E Resolution Selectable video compression resolution as below 1280 x 960 1280 x 720 1024 x 768 800 x 600 640 x 480 352 x 288 352 x 576 720 x 288 720 x 576 352 x 240 352 x 480 720x 240 720 x 480 E Frame Rate Select video frame rate the maximum
11. Explorer E High Reliability Embedded system System recovery by dual Watch dog functions 3 Product and Accessories VC58SM System User Manual USER GUIDE zm Picture 1 Package VC58SM User Manual 4 Part Names and Function Cable Configuration 1 Front C Mount lens adaptor 2 Right side Intelligent Day Night mechanical dina Ri cad filter changer Inside Photo sensor Inside Widelux Super WDR CCD sensor Inside Back focus adjustment Knob Tolerance 0 5mm Fixture Back focus adjustment Knob Fine tune the Back Focal Length DC VIDEO Select S W UP VIDEO IRIS DOWN DC IRIS 3 Back side aces VIDEO OUT Sensor In oe Relay out ig IN i POWER 77 LAN a F SENSOR ALARM VIDEO OUT DC12V AUDIO Audio in out VC58SM User Manual 5 System Connections VC58SM IP Cameras can be connected in either 1 to 1 connection where one VC58SM is connected one client or a decoder system or 1 to many connections where one VC58SM can be connected several PCs and decoder systems B Topology Generally VC58SM and a PC or a decoder are connected in a 1 to 1 mode or a 1 to many configuration 1 1 connection Site Remote Center Remote Center Site Remote Center One VC58SM is installed at a site where video images are transmitted A PC or a decoder is installed at a central location t
12. Port Configuration There is one serial port RS 485 in VC58SM The serial port can be configured as follows Mode Selection Bitrate 2400 4800 9600 19200 38400 57600 115200 bps Data Bits 5 6 7 8 bits Parity NONE EVEN ODD bit Stop Bit 1 2 bit The serial ports configurations must be same as connecting device 22 VC58SM User Manual m 2 PTZ Type Select the type of PTZ receiver PTZ ID Since it is possible to control multiple receivers over a single control line each receiver will be assigned with a unique ID Enter PTZ ID of a receiver for control The ID value range can be between 0 and 255 PTZ Port Select the serial port used for PTZ camera control Direct Keyboard Control Keyboard controller can be connected to VC58SM directly to control zoom and focus E Sensor There is one sensor input port on VC58SM The sensor port can be configured to the following Function Operation OFF Not used The port is normally open and activated when NO Normally Open closed The port is normally closed and activated when NC Normally Closed opened The function of the sensor port is set based on the type of the sensor connected E Sensor Schedule If you select sensor on Each sensor port can be enabled or disabled by day of a week and hour units Sensor is disabled during the grey colored duration 23 VC58SM Use
13. Version Displayed current Firmware Version E Board ID Network board ID of VO58SM recognized by system E Start Time Latest system boot date and time E Current Time Current date amp time enter a new date and time and press Set Current Time button to update date amp time E Time Zone Select time zone where the system is installed Depending on the time zone Daylight saving time will be adjusted automatically E Automatic synchronization with NTP Synchronize system time with an NTP server using NTP network time protocol Name of the NTP server should be registered on NTP server Name E Reboot System Pressing Reboot Server button will cause the system to reboot Do not press the Reboot button unless the server needs a reboot W Factory Reset Current IP Address of VC58SM is changed to default IP Address 192 168 10 100 System log and user registrations are also cleared The other setting value will be remained 14 VC58SM User Manual 2 2 Video Setup Live View System Video Audio Network Serial Event Video Preset User Encode Enable Preview Off O 1280x720 Resolution 0 Scaling Framerate 20 Preference Bitrate M Quality Econo Bitrate 8000 kbps 32 8000 150 I Frame Interval a Dual Encode Use Dual Encode Off On Dual Encode Algorithm 9 H 264 MJPEG Preference Bitrate Resolution
14. er setup For Remote Setting user should be authorized higher than manager level nter IP Address Q Press Setup button Video Surveillance Windnws Internet Explorer FO i E 192 168 10186 B VYTIVETS EPIFT TTPTEITTE m de Video Surveillance B Live View Setup Change User 2 0 Megapixel IP Camera Video Select Primary Secondary View Size 12 The configurations are grouped into 9 categories System Video Audio Network Serial Event Preset User and Camera Any configuration changes are not applied until Apply button is pressed Leaving the page without pressing Apply button changes in the page will be discarded 12 VC58SM User Manual 2 VC58SM Setup 2 1 System Setup Live View Change User System Video Audio Network Serial Event Preset User Camera System General System ID Video Server Language English v Apply Firmware Version Enc V1 102A 999 Board ID 66 Time Start Time 2000 06 26 9 28 48 Current Time 2000 06 26 13 08 04 Time Zone GMT 12 00 International Date Line West v Automatically synchronize with NTP server NTP Server Name Apply Reboot Factory Reset 13 VC58SM User Manual System ID Designate system ID Designated ID is displayed in Web viewing E Language Select language accordingly W Firmware
15. ere FRI TEAT Ie FERAE REFER EVE Re KATE 8 VE GOMNMECUNG 8 3 Connecting Seral PO Sisirain 8 4 Connecting Sensor amp eee nennen ense nennen ense nennen 8 5 COnbectlng POWSEsos oor ier ED pe ROSE EROR EYES EDO REOR tA NUR Bel NIRE PERS 8 6 CHECKING Operatlrg ence rere teet ea eto Rete ebbe tendere lesa poet bee e uri Perieg 8 9 oyster OPSA OM ccu ERE 9 te Remote Video MONMONNG tet e E D E RU I MP EE P UM IEEE E FOE EP TIERE 9 2 InitialiZation of IP AddEeS8 n iiir re rr ette E e ee er reed ete ep dye Pe epe rete rs 11 4 Remote ContIguratlOri am Ex EE aaa o EE PRA 12 1 Using 2 212 o tirer E ER ee va ERE Eta 12 2 SOUP 13 2 13 ZEAB ITo ETE 15 ZERO 18 LV MIU C 19 2 5 Port COntigUFellOl esee rrr rode EREE ER FER HET REPRE RN 22 2 6 Event eus petas tta eS RE e baa AR ae RES ER ERA ERE ERENAR FR 24 Gel RSC E E 27 MI iai
16. eted by pressing Delete button Change Password Pressing Modify Password button after selecting a user shows a page for changing password In case changing admin password old password is checked Modify Privilege Level Pressing Modify Privilege button after selecting a user shows a page for changing the privilege It is not allowed to change the privilege level of admin user System Video Audio Network Serial Event Preset User Modify Privilege Level ID user Privilege Level User v W Login Policy Skip Login is provided for convenient access to the server when authentication is not required When Skip Login is set to Enable login step is skipped The privilege level after login in this way is determined by the setting of Privilege Level After Login Skipped 29 VC58SM User Manual 2 9 Camera Camera Privacy Mask Select Mask Masi Day amp Night Mode Auto Night Level 25 Day Level zi 25 Auto VVhite Balance Mode ATVV Auto Exposure IRIS DC Brightness A 20 Flickerless Off 60Hz 9 50Hz BLC Mode Off On LSC Lens Shading 0 Correction Level c AGC Analog Gain 20 AGC Digital Gain A 20 Effect Gain UPT 8115 a BY DEE 15 Sharpness Enhancement 8 Level a Sharpness Coring Level a 5 Mirror V Flip Normal DNR Edge 1 a DNR Intensity 5 30 VC58SM User Manual
17. he selected mode further configuration items come as follows IP Mode Selection Description Local IP Fixed IP address Fixed IP Local Gateway Gateway IP address Local Subnet Subnet mask DHCP IP N A r Please get IP address information from your ISP provider or network manager B DNS Set DNS server IP address E Base Port Network base port is used for communication between systems In order for the VC58SM and remote systems to be connected together each port number must be identically set HTTP Port HTTP port used for web based connection B RTSP Port RTSP port used for RTSP based connection m SNMP VC58SM can be used as an SNMP agent It is compatible to both SNMPv1 and SNMPv2c Vender specific MIBs for IP camera server are defined SNMP listen port can be set and disabled when it is 0 SNMP trap is also supported Destination IP and port can be set If one of these values is 0 SNMP trap will be disabled W Multicast IP The multicast IP address selection range is between 224 0 1 0 and 238 255 255 255 The selection can be used only when media protocol is set to Multicast The multicast address must be the same for the System to be connected using multicast protocol m DDNS Select the DDNS Dynamic DNS server to use One of the two servers can be selected TrueDNS use TrueDNS service Systems can be registered on the website for TrueDNS service 20
18. his case E Screen Size Adjustable Screen Size W Digital Zoom Max 5x Digital Zoom is available W Focus Near Focus Far Auto Focus Adjust the focus E Sensor Input When the sensor on the VC58SM is connected and working the light turns red E Alarm Output Alarm Output button can trigger an event directly from the Live View page B Snapshot Snapshot button saves a snapshot of the video image currently on display Captured picture can be stored as BMP or a JPEG file E Transfer audio to audio device connected VC58SM 10 VC58SM User Manual 2 Initialization of IP Address If VC58SM s IP address is lost the VC58SM can be reset Press a reset button on the back of the VC58SM this will reset the camera to factory defaults as follows While the system is in operation press the reset button for more than 5 seconds Q The system will reboot automatically Once the system has been rebooted IP address will be set to the following IP mode Fixed IP IP address 192 168 10 100 Subnet mask 255 255 255 0 Gateway 192 168 10 1 Base port 2222 Http port 80 11 VC58SM User Manual 4 Remote Configuration 1 Using Remote Configuration Remote setting is available by using web browser Enter the IP address of VC58SM and then live view screen appears as below Press Setup button located in the upper right area of the monitoring screen to go to the serv
19. mary Video 9 Secondary Video H 264 only O JPEG Capture VC58SM User Manual The VC58SM has one sensor port and one alarm port When a decoder system instead of a PC client is connected to a VC58SM one system becomes Local system and the other a Remote system Generally a System which is being used by the user is called as Local system Then actions for events can be configured for events from the remote system as well as for local system For example it is possible to turn on an alarm device in local center decoder system when a sensor device in remote site IP camera is triggered Local section configures the actions for events from local self system and configuration activates local devices and Remote sections configure the actions for events from remote peer system The following table lists the possible actions for events Action Description Sensor In One sensor in port Alarm out Triggers alarm relay port Sends E mail to the specified address AVI file can be E mail attached FTP Upload AVI file to a specified FTP server E Sensor Configure the actions when the sensor is activated Multiple actions can be set for a single event E On Video Loss Configure the actions when video input signal is lost Multiple actions can be set for a single event E On Motion Configure the actions when motion is detected Multiple actions can be set for a single event On Disconnect
20. n 28 2 9 i bt IRE 30 VC58SM User Manual Introduction 1 About User Manual The User Manual is provided to advise how to use this premium network camera VC58SM This manual includes how to trouble shoot in case of problems as well as installation operation and setting up the VC58SM 2 Features VC58SM is a 1 3 Megapixel network based camera with remote live monitoring audio monitoring and control via an IP network such as LAN ADSL VDSL and Wireless LAN B Video Highly efficient compression algorithm H 264 amp MJPEG support 18 kinds of compression and resolutions 352 240 1280 x 1024 Wide range of transmission rates 32kbps 8Mbps Various transmission modes CBR VBR Motion detection B Audio Multi transmission mode Simplex VC58SM gt Client PC or Decoder Client PC or 585 Full Duplex B Network Fixed IP amp Dynamic IP DHCP support 1 1 1 N support Multicasting Automatic transmit rate control according to network conditions Serial Data RS 485 support Data pass through mode serial data communications between VC58SM and Decoder E Sensor amp Alarm Support direct connections of external sensor and alarm devices Eventalarm Decoder VC58SM User Manual E User Interface Diagnose and upgrade through dedicated program called True Manager System configuration using Internet
21. network cable to Ethernet port 2 Connecting Audio Audio is full duplex It is possible to set the mode as Tx only Rx only or Tx Rx Connect audio input and output ports to audio devices accordingly The Audio signal required is line level so audio equipment with an amp mixer or other amplifier should be used 3 Connecting Serial Ports RS 485 of VC58SM can be connected to external equipment such as PT receiver etc client can send PT commands to the external equipment via the serial port When a decoder system instead of PC client is connected to VC58SM the serial port and that of the decoder system works in pass through mode That is data from at one port is delivered to the other port vice versa 4 Connecting Sensor amp Alarm Connect sensor and alarm devices to corresponding terminals accordingly 5 Connecting Power After confirming the power source connect power adaptor and then 12V DC connector to the system 6 Checking Operating Once the power is supplied to the camera it will start booting The system will boot up to an operating mode after approximately 40 60 seconds The green LED on the Ethernet port will flash indicating the system is ready Software provided on the disc called True Manager allows you to check the IP address and other network details of the camera Please refer to the True Manager manual for instructions on how to find the IP address of the camera and if required changing
22. ng PTZ control buttons Enter Preset name G Press Set button Once all the presets are set press Save List button Move to Preset Position Select a preset from the Preset and press Go To button then the camera will move to the selected preset position 27 VC58SM User Manual 2 8 User Setup Live View Change User System Video Audio Network Serial Event Preset User Camera User User List ID Privilege Level admin Admin Add Delete Modify Password Modify Privilege Login Policy Skip Login 9 Disable O Enable Privilege Level After Login Skipped User can be registered and privilege level of a user can be specified User configuration is allowed only to admin user Max 16 users can be registered and each user can have one of four privileges Privilege Allowed Operations Remarks Admin All operations User ID admin All operations except for user Manager configuration User Live viewing and PTZ control Guest Live viewing only W Add User Page for adding a user comes on pressing Add button Setup Live View Change User System Video Audio Network Serial Event Preset User Camera Add User ID Password Privilege Level Manager User ID and password need to be entered and privilege level need to be selected User ID and password 28 VC58SM User Manual consist of alphanumeric string of max 15 characters W Delete User A user is del
23. o receive and view the video images on an analog monitor Audio and serial data are transferred in either direction 1 N connection Site Remote Center VC58SM PC or Decoder PC or Decoder PC or Decoder In this configuration a site can be monitored from many remote central locations Although up to 64 PCs or decoders can be connected to on VC58SM in the real network environment network bandwidth can limit the maximum connections VC58SM User Manual Functionally the central monitoring system CMS software provided can replace the decoder Multicast If the network supports multicasting a large number of decoders can be used to receive video effectively from a VC58SM using a single streaming of video and audio Relay Site Center 1 Center 2 Video and audio can be retransmitted from a center to another center The arrangement is useful when the network bandwidth to the site is limited while there are more than one center want to monitor the site CMS Central Monitoring System Site Remote Center VC58SM 7 Site Remote Center CMS is a Window based remote monitoring program in order to monitor or control video audio and events in real time from several IP cameras or video servers Please refer to the CMS User Manual for more in detail VC58SM User Manual 2 Installation 1 Connecting Network LAN Connect the power adaptor to VC58SM Connect
24. r Manual 2 6 Event Configuration Setup Live View Change User System Video Audio Network Serial Event Preset User Camera Event Local Sensor Alarm E mail No Preset On Video Loss Alarm E mail L FTP Preset v On Motion Alarm E mail Preset v Remote Sensori Alarm E mail Preset Sensor2 Alarm E mail No Preset v Sensor3 Alarm L E mail L FTP Preset v Sensor4 Alarm E mail Preset v On Disconnect On Disconnect Alarm E mail Preset v Duration Alarm E mail Notification Server Address Port Sender Address Authentication on SMTP server ID Password Destination Address Video Clip Attaching FTP Upload Server Address Port ID Password Upload Video Continuous Upload Upload Duration Upload Interval Event Record Pre event Time Post event Time lt synchronous mail truen co kr 25 yckim truen co_kr yckim truen co_kr Off O Primary Video Secondary Video H 264 only O JPEG Capture E mail Test Before testing e mail please apply your configuration first 192 168 10 31 21 yckim 300 3600 Nj None 24 O Pri
25. s port needs to be changed accordingly ID and password for accessing the FTP server also need to be specified Video clip of AVI file format or JPEG file at the moment of the event can be attached by setting Video Clip Attaching By setting Continuous Upload to On it is possible to upload video clip periodically regardless of events Upload Duration specifies the duration of one upload file and Upload Interval specifies how often it should happen Upload Interval doesn t include the duration If Upload Interval is 60 and Upload Duration is 20 it uploads a file for 20 seconds duration every 80 seconds W Event Recording Specify how a video clip is to be generated for E mail sending or FTP uploading Pre event Time specifies the duration of recording before an event happens Post event Time specifies the duration after the event is cleared 26 VC58SM User Manual 2 7 Preset Setup Live View Change User System Video Audio Network Serial Event Preset User Camera Preset Q Preset Name 6 7 8 9 11 Save Press Set Button This function is only available when a PTZ receiver is used with VC58SM Configure up to 15 preset positions Preset function is not available on some PTZ receivers Make sure to check if a PTZ receiver supports preset E Preset Configuration Set the PTZ Presets by following the next steps Move cameras to desired view usi
26. t Rate 64K BPS Input Line In Mini Stereo Single Mono 1 EA 32 VC58SM User Manual Output Line Out Mini Stereo Single Mono 1 EA Sensor Input 1 Input Normal Open Contact Alarm Output 1 Output Normal Open Contact Dimension 66 W x57 V X126 5 L Weight 800g Power DC 12V 2A PoE 802 3af Others Power Consumption MAX 12W Operation 10 C 50 14 F 122 F Temperature Specification amp Design are subject to change without prior notice 33
Download Pdf Manuals
Related Search