Transceiver Module TCM 410J 20 August 2013
Contents
1. Green Smart Wireless enocearn 20 August 2013 Observe precautions Electrostatic sensitive devices Patent protected WO98 36395 DE 100 25 561 DE 101 50 128 WO 2004 051591 DE 103 01 678 A1 DE 10309334 WO 04 109236 WO 05 096482 WO 02 095707 US 6 747 573 US 7 019 241 EnOcean GmbH Phone 49 89 67 34 689 0 Subject to modifications Kolpingring 18a Fax 49 89 67 34 689 50 TCM 410J User Manual 82041 Oberhaching info enocean com August 20 2013 Germany www enocean com Page 1 24 USER MANUAL V1 10 Green Smart Wireless enocearn TCM 410 REVISION HISTORY The following major modifications and improvements have been made to the first version of this document No Major Changes Initial version Added certification information and PCB Design Published by EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany www enocean com info enocean com phone 49 89 6734 6890 EnOcean GmbH All Rights Reserved Important This information describes the type of component and shall not be considered as assured characteris tics No responsibility is assumed for possible omissions or inaccuracies Circuitry and specifications are subject to change without notice For the latest product specifications refer to the EnOcean web site http www enocean com As far as patents or other rights of third parties are concerned liability is only assumed for modules not for the described applications proc2. For good receiver performance great care must be taken about the space immediately around the antenna since this has a strong influence on screening and detuning the an tenna The antenna should be drawn out as far as possible and must never be cut off Mainly the far end of the wire should be mounted as far away as possible at least 15 mm from all metal parts ground planes PCB strip lines and fast logic components e g micro processors Do not roll up or twist the whip antenna Radio frequency hash from the motherboard desensitizes the receiver Therefore m PCB strip lines on the user board should be designed as short as possible m A PCB ground plane layer with sufficient ground vias is strongly recommended 4 2 3 Helical antenna 928 35 MHz according to drawing below connect to RF WHIP Minimum GND plane 35 mm x 30 mm Minimum distance space 10 mm 2 Windungsbereich 2 coil area 1 Windungsbereich 0 5 Windungen Steigung 4 2 t0 4 mm coil area 0 5 coils pitch 4 2 0 4 mm 2 Windungsbereich 6 65 Windungen Steigung 3 1 mm coil area 6 65 coils pitch 3 1 mm gestreckte L nge 141 7 mm developed length 141 7 mm Doppelbemafung douple dimensioning 1 entspricht ganze Windung 4 2 2 corresponds to whole coil 4 2 2 2 betrifft Schenkelstellung bezogen auf Windungsanfang concerns leg position referred to the beginning of coil Windungen d rfen sich nicht ber hren coils must not be in contact Ma
3. Switch e g Smar PTM 210J STM4xyJ J ESP3 TCM410J KA Smart Ack Sensor 9 0 2 KA es STM400J AC With API SmartAck MN Oo e Radio Gateway L TCM410J FSP x 3 6 Serial Interface TCM 410 provides a bi directional serial interface which conforms to the EnOcean ESP3 specification For details regarding ESP3 please refer to the ESP3 specification The data rate on the serial interface is 56 8 kbit s which is usually interoperable with systems run ning at 57 6 kbit s Direction Nominal serial data rate Tolerance TK sent by module 56888 bit s 57600 bit s 1 23 lt 50 ppm RX received by module 456888 bit s lt 5 The following ESP3 commands are supported Type 1 Radio command for transparent mode compatible mode Type 10 Radio command for transparent mode native mode Type 2 Responses Type 4 Event o SA_CONFIRM_LEARN to confirm discard learn in out o CO_READY to indicate wake up from deep sleep initiated by CO_WR_SLEEP Type 5 Common commands o CO WR SLEEP to enter energy saving mode deep sleep mode o CO WR RESET to reset the device o CO RD VERSION to read SW HW versions chip ID etc o CO WR BIST to perform flash BIST operation o CO WR IDBASE to write ID range base number o CO RD IDBASE to read ID range base number http www enocean com en enocean modules tcm 310 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 10 24 USER MANUAL V1 10 Green Smart Wirel
4. 2 1 Basic functionality TCM 410J is a SMD mountable radio transmitter mod ule enabling the realization of gateways for EnOcean 928 35 MHz radio systems It provides a bi directional radio interface and a bi directional serial interface Radio messages are sent transparently through the serial interface in both directions from and to an ex ternally connected host processor or host PC In addi tion control commands can be sent from the host e g to configure the repeater functionality or to manage Smart Ack functions TCM 410J can act as postmaster for up to 15 bi directional sensors using Smart Ack technology Features m Smart Ack controller functionality Transparent radio channel Programmable repeater functionality 1 Level ESP3 support EnOcean Serial Protocol V3 API programmable 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 4 24 USER MANUAL Green Smart Wireless enocearr 2 2 Technical data Features overview Antenna External whip or 50 antenna mountable Frequency 928 35 MHz FSK Radio Standard Enocean Radio Protocol 2 FSK Data rate Modulation type 125 kbps FSK Receiver Sensitivity at 25 C typ 95 dBm Conducted Output Power typ OdBm Power Supply 2 6 5V Serial Interface UART EnOcean Serial Protocol 3 Current Consumption Receive mode 27 mA Transmit mode 22 mA Dimensions of PCB 22x19x3 1 mm Operating temperature 25 to 85 C Radio Regulations ARIB STD T108 2 3 Phy
5. any above men tioned pin This may lead to unpredictable malfunction of the device For I O pins configured as analogue pins the IOVDD voltage level is not relevant However it is important to connect IOVDD to a supply voltage as specified in 3 4 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 8 24 USER MANUAL V1 10 Green Smart Wireless TCM 410 IOVDD mi If configured as digital I O DISUYVN PB PEPE PE PB PB gt HHORRRRR9R09 PURmOOOOGOOGOGO Io iu UPON JU etium feros des p O pan ORS 3 3 Absolute maximum ratings non operating Symbol Parameter Min Max Units V GND _ Groundconnection CE 0 0 Vv VINA Voltage at every analog input pin VIND1 Voltage at RESET and every digital input pin except 0 5 3 6 V WXIDIO WXODIO VIND2 Voltage at WXIDIO WXODIO input pin 3 4 Maximum ratings operating Symbol Parameter Max 0 o 0 VINA Voltage at every analog input pn 0 Voltage at RESET and every digital input pin except B 3 6 WXIDIO WXODIO VIND2 Voltage at WXIDIO WXODIO input pin 0 VDDR jMax rippeat VDD J mVpp 3 5 System environment In the figure below TCM 410J is shown in a typical system environment 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 9 24 USER MANUAL V1 10 Green Smart Wireless enocean Uni or bidirectional Actuator e g TCM 410J Unidirectional Radio Gateway Sensor or
6. age length of up to 256 bytes This enables an external micro controller con nected to TCM 410J to handle remote management request from external devices or to control other devices via remote management For more information on remote manage ment please refer to http www enocean com en knowledge base 3 10 Serial communication with TYPE 01 or TYPE 10 TCM 410J operates as transparent gateway so the received radio telegrams are forwarded on as serial packets to external controller with type 01 or type 10 The mode can be switched by the serial command CO WR MODE Usage of Type 01 is for compatibility reasons compatibility mode Usage of Type 10 is native for the Radio Protocol of TCM 410J The scenario is depicted on the figure below EnOcean Radio Protocol 1 Radio Signal EnOcean Radio Protocol 2 Radio Signal Mative translation EnOcean Serial Protocol ESP3 Packet Type 01 For transmission requests from external controller to the TCM 410J both types can be used at any time of the operation EnOcean Serial Protocol ESP3 3 11 Module configuration Configuration parameters will be stored in a non volatile memory on the TCM 410J module The parameters will be changeable with the Dolphin Suite configuration The following pa rameters will be adjustable default mode selection if serial message are forwarded with serial type 01 or serial type 10 sniffer mode selection puts module into sniffer mode
7. cean www enocean com TCM 410J User Manual V1 10 Page 21 24 USER MANUAL Green Smart Wireless enocean 4 6 Soldering information TCM 410J shall be soldered according to IPC JEDEC J STD 020C standard Average Ramp Up Rate Ts to Tp 3 C second max Preheat Temperature Min TS 150 C Temperature Max TSmax 200 C Time tS to tS max 60 180 seconds Time maintained above Temperature T 217 C Time t 60 150 seconds Peak Classification Temperature Tp 260 C Time within 5 C of actual Peak Temperature tp 20 40 seconds Ramp Down Rate 6 C second max Time 25 C to Peak Temperature Note 1 All temperatures refer to topside of the package measured on the package body surface A D Critical Zone T to Tp dM Temperature Preheat T 1 n f I 1 4 t 25 C to Peak Time gt IPC 020c 5 1 TCM 410J shall be handled according to Moisture Sensitivity Level MSL4 which means a floor time of 72 h TCM 410J may be soldered only once since one time is already con sumed at production of the module itself Once the dry pack bag is opened the desired quantity of units should be removed and the bag resealed within two hours If the bag is left open longer than 30 minutes the desiccant should be replaced with dry desiccant If devices have exceeded the specified floor life time of 72 h they may be baked according IPC JEDEC J STD 033B at max 90 C
8. er Manual V1 10 Page 7 24 USER MANUAL V1 10 Green Smart Wireless enocearn TCM 410 3 2 Pin description and operational characteristics HW Symbol Pin Function Characteristics 1 5 7 17 18 Ground connection Must be connected to GND see 4 4 24 26 ae 31 VDD DENEN pee Reamer een NNNNN req ulator output ae IOVDD 23 Must be connected to desired inter face supply voltage see 3 4 See also 3 2 1 SER TX ADIO7 16 UART output See36 RE WHIP 4 RFoutput Output for whip antenna 6 RFoutpu 50O0hm output for external antenna RF 50 n c 3 9 14 19 22 Not connected E not connect 29 30 32 34 3 2 1 GPIO supply voltage IOVDD For digital communication with other circuitry peripherals the digital I O configured pins of the mixed signal sensor interface ADIOO to ADIO7 and the pins of the serial interface SCSEDIOO SCLKDIO1 WSDADIO2 RSDADIO3 may be operated from supply voltages different from DVDD Therefore an interface voltage supply pin IOVDD is available which must be connected either to DVDD or to an external supply within the tolerated voltage range of IOVDD If DVDD 0 V e g in any sleep mode or if VDD VOFF and IOVDD is supplied there may be unpredictable and varying current from IOVDD caused by internal floating nodes It must be taken care that the current into IOVDD does not exceed 10 mA while DVDD 0 V If DVDD 0 V and IOVDD is not supplied do not apply voltage to
9. ess enocearn TCM 410 o CO_WR_REPEATER to configure repeater functionality o CO_RD_REPEATER to read repeater state o CO_WR_FILTER_ADD to add filter to filter list up to 10 filters are supported o CO_WR_FILTER_DEL to delete filter from filter list o CO_WR_FILTER_DEL_ALL to delete all filter o CO WR FILTER ENABLE to enable disable supplied filters o CO RD FILTER to read supplied filters o CO WR WAIT MATURITY to wait maturity time before returning radio telegrams o CO WR MODE Sets the gateway transceiver mode either packet type 01 or pack et type 10 m Type 6 Smart Acknowledge commands O SA_WR_LEARNMODE to set reset Smart Acknowledge learn mode SA_RD_LEARNMODE to get learn mode SA_WR_LEARNCONFIRM to add or delete a mailbox of a client SA_WR_RESET to send a reset command to a client SA_RD_LEARNEDCLIENTS to get learned mailboxes clients O SA_WR_POSTMASTER to activate deactivate post master functionality m Type 7 Remote Management messages up to 256 Bytes O O O All configuration values set via ESP3 commands are held in RAM and will therefore be lost after RESET or after a deep sleep phase Only Smart Ack mailboxes are stored in FLASH and are available also after RESET or a deep sleep phase After sending a CO_WR_RESET command the following CO_READY event indi cates wake up reason 06 meaning A memory request from the CPU core does not correspond to any valid memory location This is caused by the real reset cause used
10. esses and circuits EnOcean does not assume responsibility for use of modules described and limits its liability to the replacement of modules determined to be defective due to workmanship Devices or systems contain ing RF components must meet the essential requirements of the local legal authorities The modules must not be used in any relation with equipment that supports directly or indirectly human health or life or with applications that can result in danger for people animals or real value Components of the modules are considered and should be disposed of as hazardous waste Local government regulations are to be observed Packing Please use the recycling operators known to you 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 2 24 USER MANUAL V1 10 Green Smart Wireless enocearr TCM 410J TABLE OF CONTENT MODULE VARIANTS AND RELATED DOCUMENTS c cene n Hn nnns 4 GENERAL DESORIP TION S saari abit ata abaran ad al SEE Kaap apaa aab ai apan MORE EROS E DNUS AA dE 4 2 1 Basic functionality REL 4 Z2 TTNG A CA a S E ni BAGA a A GN 5 FS Nec siusi m le POTUM 5 ge dss semau sisibsegeten Mem er 6 2 5 Ordering information ccesssseeeeeeeeeeeeee een nnns 6 FUNCTIONAL DESCRIPTION eeeeeeeeenn nnns 6 SML C T AA ANAN 6 3 2 Pin description and operational characteristics eese nnn 8 3 24 GPIO Supply v
11. fective wall thickness and with it the signal attenuation varies according to this angle Signals should be transmitted as directly as possible through the wall Wall niches should be avoided Other factors restricting transmission range m Devices mounted on metal surfaces shielding and detuning of antenna may cause heavy loss of transmission range m Hollow lightweight walls filled with insulating wool on metal foil m Suspended ceilings with panels of metal or carbon fibre m Lead glass or glass with metal coating steel furniture The distance between EnOcean receivers and other transmitting devices such as com puters audio and video equipment that also emit high frequency signals should be at least 0 5 m A summarized application note to determine the transmission range within buildings is available as download from www enocean com 4 2 Antenna options 4 2 1 Overview Several antenna types have been investigated by EnOcean Please refer to our application notes AN102 and AN105 which give an overview on our recommendations 4 2 2 Whip antenna 928 35 MHz Antenna 64 mm wire connect to RF_WHIP Minimum GND plane 50 mm x 50 mm Minimum distance space 10 mm 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 13 24 USER MANUAL Green Smart Wireless enocean Positioning and choice of receiver and transmitter antennas are the most important factors in determining system transmission range
12. for less than 60 h Devices packaged in moisture proof packaging should be stored in ambient conditions not exceeding temperatures of 40 C or humidity levels of 90 r H TCM 410J modules shall be soldered within 6 months after delivery 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 22 24 USER MANUAL 4 7 Tape amp Reel specification Seas 5 wa SA 33 343 Es Ses 2013 EnOcean www enocean com Green Smart Wireless enocearn v c o n c Y D D gt G U Tape running direction TCM 410J User Manual V1 10 Page 23 24 USER MANUAL 5 AGENCY CERTIFICATIONS Green Smart Wireless enocean The modules have been tested to fulfil the approval requirements based on the built in firmware When developing customer specific firmware based on the API for this module special care must be taken not to exceed the specified regulatory limits e g the duty cycle limitations 5 1 Japanese Type Approval TCM 410J complies with the Japanese radio law and is certified according to ARIB STD T108 When the product is placed on the Japanese market it must carry the Specified Radio Equipment marking as shown below R 206 000372 T If the certification label cannot be recognized from outside e g installation in a host ap propriate information must be referenced in the user manual Notified Body Directive 99 5 EC Notified Body EMC Di
13. ion File TCF Details Technical Standards and Specifications The product complies with Ordinance Regulating Radio Equipment Radio Regulatory commission No 18 1950 Chapter General Provisions Chapter Transmitting Equipment Chapter III Receiving Equipment Article 49 14 Documentation submitted for the Type Certification Issue Date Issued by 2013 07 10 EMCCons DR RASEK GmbH amp Co KG ent layout intemal amp extemal photographs Label sa Schematic diagrams User manual Quality System documentation ISO 9001 Certificate for manufacturer Technical characteristics Type of modulation Emission designator Operating frequency range Rated transmitter output power Maximum antenna gain Other information The device is certified for operation with the following antenna s ANT 300 helical antenna 2 15 dBi gain Whip antenna 64mm 3 89 dBi gain USB 400J top loaded PCB spiral antenna 1 14 dBi gain EMOced DR RASEK GmbH Stoemhofer Berg 15 91364 Unterisirieiter Gemnany Tel 49 91947277901 Fax 49 0194 72279 06 E mail emc oetfpemoc de Web www emoc de TCM 410J User Manual V1 10 Page 24 24
14. itor between VDD and GND close to the module material X5R X7R min 6 3 V to avoid derating effects In addition a 470 nH coil shall be inserted Murata LQW18A 0603 in the power supply line For best performance it is recommended to keep the ripple on the power supply rail below 10 mVpp see 3 4 All GND pins must be connected to GND Be careful not to create loops The ground must be realized ideally on both sides of the PCB board with many vias At least there must be a short star connection Otherwise RF performance can be reduced Layout recommendations 4 5 N The length of lines connected to I Os should not exceed 5 cm It is recommended to have a complete GND layer in the application PCB at least in the area below the module and directly connected components e g mid layer of your application PCB Due to unisolated test points there are live signals accessible on the bottom side of the module Please follow the following advices to prevent interference with your application circuit m We suggest avoiding any copper structure in the area directly underneath the module top layer layout of your application PCB If this is not possible in your design please provide coating on top of your PCB to prevent short circuits to the module All bare metal surfaces including vias have to be covered e g adequate layout of solder resist m It is mandatory that the area marked by the circle in the figure below is kept clear of an
15. nna c ccce 17 4 4 Power supply requirements ssssssesseeeeee nennen hhnhehena aas n ananas 18 4 5 Layout recommendations ssssssssseeeeeeeennnn nnne nhanh nha a aaa anna nnn nn nnn 18 4 5 1 Recommended foot pattern ss sasae anaa aana a nana a anana anana nnn nnn nn nnn 19 4 6 Soldering information 0 ccc cece cece EEE anana anana anana anana anana 22 4 7 Tape amp Reel specification s seser nnne nnn nnns 23 AGENCY CER HFICATIONS niasa aisi raaa aenak R RIEF ER naban aran a A saii raen e np aka 24 A 1 Japanese Type Approval cccccccceeeeeeeeeeeeeeeeees Error Bookmark not defined 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 3 24 USER MANUAL Green Smart Wireless enocean 1 MODULE VARIANTS AND RELATED DOCUMENTS This document describes operation of TCM 410J module with the frequency 928 35 MHz Subject of description is the build in software Gateway Controller m used hardware TCM 410J In the Document we refer to the Hardware and Software characteristic by the module name TCM 410 In addition we recommend following our application notes in particular m AN101 Power Supply Layout Layout considerations for Line Power m AN102 Antenna Basics Basic Antenna Design Considerations for EnOcean based Products The specification of the serial protocol ESP3 can be found here http www enocean com es 2 GENERAL DESCRIPTION
16. oltage IOV DD Nissan Sa OREMUS RUN A RC UU OCEAN 8 3 3 Absolute maximum ratings non operating eeesesesseeen nn nnn 9 3 4 Maximum ratings Operating sarasa aaa aka adde Reps api oM RH be a a Eu EG A AA 9 9 0 V SEO eonVIFODITICTIE saeni ia aaa an a a aa ja asi een Doubs dn Und pM aa aa b bud NDS 9 Coo R MERITI e EET aa ja esa a A an Senang Ba a bea A BR an NGA A aana GAE DENE e AN GAN AA ME AA en Sena A a Ma NB Aa Ban 10 9 7 BUNCH REDCALCE arinrin DA AR BAE AA AA ENI KD BA NADA aaa BENRA a Aak ha jah BAE aha a 11 POTAE TON dO a NAN EN Na EN NAN ETT 11 3 9 Remote Ma agement aaa saa ai ai aaa d aa aaa aa kaka aa ala Wi a aa e A Ja dam aaa ag an a an a a ah a aa ag a MA ma 12 3 10 Serial communication with TYPE 01 or TYPE 10 cene mn HI 12 oll Mod le configurato sas aaa kk ak ka a BAKA A Nn UM WA ANAN aana An A ra AE EUN BIG ENDE MGE A A APA NUM 12 APPLICATIONS INFORMATION as ilaa aki rada aa te ha nen Vedi We a ma a Vos d a en vane Wa Wa c 13 dt TransmisSioN TTE naa KANEKA KE aa Kg RARA KAB KE AK ARKA GE NAA EAn ANA KA WAE 13 4 2 Antenna OptiOons s ssssssesasasa rasanan akarana anana nana nana E TOOL 13 4 2 1 OVOCTVICW 13 22 2 Whi antenna sasaran kanaka Na ANE KNA ors Ba a AN QUEE GER E DUST RUE KENAN a xa Ru ard AR 13 4 2 3 Helical antenna sess is nia d Ra REAN PREEVRREXE MOL PERPE RE PEVIDI MEE EFE ER SEdaGURE URPrEERENEQ CE d FE 14 4 3 Recommendations for laying a whip ante
17. rective 2004 108 EC T RF CAB under the Japan EC MRA EM fi d FCB under the Canada EC MRA CM TCB under the USA EC MRA Designated by the German Regulator Bundesnetzagentur to act as a Recognised Foreign Conformity Assessment Body in accordance with the Japan EC MRA CONSTRUCTION TYPE CONFORMITY CERTIFICATE for Specified Radio Equipment Registration No JU000372D Certificate Holder EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Product Category Article 2 Paragraph 1 Item 8 Y Product Designation STM 400J TCM 410J USB 400J Product Description Scavenger Transceiver Module Transceiver Module USB Gateway Software Release No Manufacturer Katek GmbH Bahnhofstra e 108 83224 Grassau Germany When the product is placed on the Japenese market tmustcany the PE R 206 000372 as shown on the right The scope of evaluation relates to the submitted documents only This Certificate confirms that the listed product has demonstrated conformity with the relevant technical regulations defined in the attached Annex It is only valid in conjunction with the Annex X 2013 08 09 Klaus Kn ng Recognised Foreign Conformity Body EMCCETDR RASEK GmbH Sipemhofer Berg 15 91364 Unterieinieiter Germany Tei 449 9194 72279 01 Fax 49 9194 72279 06 E mail emc certfgemcc de Web www emcc de 2013 EnOcean www enocean com Annex to Certificate Registration No JU000372D Date 2013 08 09 Page 1 of 1 Technical Construct
18. se compo nents can be seen in figure below 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 15 24 USER MANUAL Green Smart Wireless enocean Position of matching components The antenna was matched to 500 input impedance at the feed point A compromise for a good matching when plugged into a laptop and when plugged to the end of a USB cable was chosen Several environments in the proximity of the antenna where also evaluated for this compromise The following table shows the values of the proposed components Component Value 0603 components where used for the antenna matching For the capacitor general purpose COG capacitors with 5 tolerance are sufficient The inductors should be wire wound induc tors from the Wurth WE KI series or the Murata LQW series 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 16 24 USER MANUAL Green Smart Wireless enocearnr 4 3 Recommendations for laying a whip antenna Antenna too close to GND area Antenna end led back to foot point Antenna too close to GND area 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 17 24 USER MANUAL V1 10 Green Smart Wireless enocearr TCM 410J 4 4 Power supply requirements In order to provide a good radio performance great attention must be paid to the power supply and a correct layout and shielding It is recommended to place a 22 uF ceramic ca pac
19. sical dimensions Unless otherwise specified dimensions are in mm Tolerances PCB outline dimensions 0 2 mm All other tolerances 0 1 mm TCM 410J pads on bottom side of PCB PCB Dimension 22x 19x 3 1 mm Weight 1 99 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 5 24 USER MANUAL V1 10 Green Smart Wireless TCM 410 2 4 Environmental conditions Operating temperature 25 C 85 C Storage temperature 40 C 85 C Storage temperature in tape amp reel package 20 C 50 C Humidity 0 93 r H non condensing 2 5 Ordering information Type Ordering Code Frequency TCM 410J S3063 K410 3 FUNCTIONAL DESCRIPTION 3 1 Pin out O 22 288282 c c c O 3 3 O t o GND VDD DVDD n c GND IOVDD RSDADIO3 ll ba WSDADIO2 i i SCLKDIO1 rane TCM 4103 SCSEDIOO GND TOP VIEW PROG EN RVDD ADIOO 1 9 ADIO7 GND uo o ea lt x PN Lf o ea t ADIO4 e o ea x ADIO1 ADIO2 The figure above shows the pin out of the TCM 410J hardware The pins are named accord ing to the naming of the Dolphin chip to simplify usage of the DOLPHIN API 2 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 6 24 USER MANUAL Green Smart Wireless enocearn The table in section 0 shows the translation of hardware pins to a naming that fits the func tionality of the built in firmware 2013 EnOcean www enocean com TCM 410J Us
20. ssstab 5 1 Cu PHC 0 85 0 02 ANT 300 pes EnOcean GnbH A77 C11 A40001 V45 83 OD Crigiral Zeichrang nicht ver Hand nde Ga Priifmas test dimension Oberfl che verzinnt l tf hig nach DIN IEC 60068 Teil 2 20 surface tinned solderable to DIN IEC 60068 part 2 20 ALS BETRI EBSCEHE WIS ANVERTRAUT ALLE RECHTE VORBEHALTEN POPRIETARY DATA COMPANY CONFIDENTIAL ALL RIGHTS RESERVED 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 14 24 USER MANUAL V1 10 Green Smart Wireless enocean TCM 410J 4 2 4 Top loaded PCB spiral antenna The design of the antenna made on a 1mm thick two layer FRA PCB The dimensions are given in figure below The hatched areas are double sided in layout The large area to the left is a ground area Components can be placed here as long as the area is not split by this nor has long cuts in it which can act as radiators its self UJ QU Q2 y 1394 461 55 655 7 B 05 445 Sr 48 546 FF feed 3 gt Eo 485b Dimensions of the PCB antenna Parameter of PCB VALUE PCB material FR4 2 layer Dimension 19 48 55 mm Layer Thickness in pm Exact description Solder Mask JAAN Solder resist Soler resst OO O Soda Gien mm AAN Em AN DN The PCB antenna uses three discrete matching components The position of the
21. when CO WR RESET will be performed It is not a SW HW malfunction 3 7 Built in Repeater TCM 410J provides the option to activate a one or two level repeater for EnOcean radio telegrams 1 Level Repeater If a received telegram is a valid and original not yet repeated the tele gram is repeated after a random delay A The repeated telegram is marked as repeated by an increased repeater counter Configuration of the repeater is done via serial interface commands For detailed recommendations regarding the usage of repeaters please refer to our applica tion note EnOcean Wireless Systems Installation Notes PDF 09 2010 3 8 Smart Acknowledge TCM 410J provides a post master function with 15 mailboxes for sensors using Smart Ack technology For more information on smart acknowledge please refer to http www enocean com en knowledge base 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 11 24 USER MANUAL V1 10 Green Smart Wireless enocearr TCM 410J When teaching in a device using Smart Acknowledge please take care to switch off all TCM 4xyJ devices which are not continuously powered Otherwise these TCM 4xyJ modules could be declared postmaster As soon as the power supply is switched off a postmaster would be missing and Smart Acknowledge would not work any longer 3 9 Remote Management TCM 410J provides a transparent radio channel also for remote management messages with a mess
22. which is suiting for network observation and evaluation baud rate selection 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 12 24 USER MANUAL V1 10 Green Smart Wireless enocearn TCM 410 4 APPLICATIONS INFORMATION 4 1 Transmission range The main factors that influence the system transmission range are type and location of the antennas of the receiver and the transmitter type of terrain and degree of obstruction of the link path sources of interference affecting the receiver and dead spots caused by Signal reflections from nearby conductive objects Since the expected transmission range strongly depends on this system conditions range tests should categorically be performed before notification of a particular range that will be attainable by a certain application The following figures for expected transmission range are considered by using a PTM a STM or a TCM radio transmitter device and the TCM radio receiver device with preinstalled whip antenna and may be used as a rough guide only Line of sight connections Typically 30 m range in corridors up to 100 m in halls Plasterboard walls dry wood Typically 30 m range through max 5 walls Ferro concrete walls ceilings Typically 10 m range through max 1 ceiling Fire safety walls elevator shafts staircases and supply areas should be considered as screening The angle at which the transmitted signal hits the wall is very important The ef
23. y conductive structures in the top layer and 0 3 mm below Otherwise RF performance will be degraded Furthermore any distortive signals e g bus signals or power lines should not be routed underneath the module If such signals are present in your design we sug gest separating them by using a ground plane between module and these signal lines 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 18 24 USER MANUAL Green Smart Wireless enocearn TCM 410 4 5 1 Recommended foot pattern Top layer GD restricted 8 0 3mm below 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 19 24 USER MANUAL Green Smart Wireless enocearn Solder resist top layer Z 2013 EnOcean www enocean com TCM 410J User Manual V1 10 Page 20 24 USER MANUAL Green Smart Wireless enocean Solder paste top layer The data above are also available as EAGLE library In order to ensure good solder quality a solder mask thickness of 150 um is recommended In case a 120 um solder mask is used it is recommended to enlarge the solder print The pads on the solder print should then be 0 1 mm larger than the pad dimensions of the module as specified in chapter O not relative to the above drawing Nevertheless an application and production specific test regarding the amount of soldering paste should be performed to find optimum parameters 2013 EnO
Download Pdf Manuals
Related Search