"user manual"
Contents
1. Feed Calbr bh Las d 8LlggGbhe2t lk CancelReset Figure 6 8 Chapter 2 Setup and Use C168 Series User s Manual Using the External Media Stand If an External Media Stand is equipped with your C168 printer stands may be an optional accessory by utilizing the stand the printer can accommodate media up to an 8 OD 204 mm media roll Install the Media Stand Position the Media Stand under the printer making sure the 2 positioning holes are lined up with the two rear printer feet see Figure 6 9 C168 External Media Stand Chapter 2 Setup and Use C168 Series User s Manual Load Media Using External Media Stand 1 Insert a Media Spindle into the Media Roll core For Media Rolls with extra large cores use the Media Roll Adaptors first to create a snug fit 2 Secure each end of the Media Roll core by placing a Media Roll Guide onto the Spindle and slide each Guide to the edge of the Media Roll Ensure the Media Roll is centered onto the Spindle See Figure 6 10 0 p Media Roll Module l A j correctly fitted with Spindle and Guides Media Roll 2 Media Roll Guide Media Spindle Media Roll Adaptors Figure 6 10 3 Open the top cover of C168 Release the printhead module and place the entire Media Roll Module onto the External Media Stand 4 Lead the media through the gap found between the top cover and the printer Then continue to lead the medi2. If the printer prints vertical blank lines as shown in the below picture it may be due to a dirty or defective Printhead See the table below for possible causes and solutions Cause Corrective Action The Printhead is dirt Clean the Printhead Follow the recommended maintenance guidelines e Printhead is dirty 4 for cleaning the Printhead Vertical lines still appear after cleaning the Contact an authorized POSTEK service provider for technical support Printhead Printer Timeout Error Message Execute following corrective actions 1 Check the interface cable for proper connection 2 Ensure the printer is powered on If the trouble still exists please contact an authorized POSTEK service provider for technical support Data Sent but Not Printing 1 Ensure the correct driver is chosen in the label software 2 Reset the printer If the trouble still exists please contact an authorized POSTEK service provider for technical support Chapter 5 Troubleshooting C168 Series User s Manual Poor Printing Quality When experiencing poor print quality check the following Adjust print darkness setting value Adjust print speed setting value Clean the Printhead and the platen roller Poor quality printing may be caused from using a low quality ribbon Change to higher quality ribbon A IAS Poor quality printing may be caused from using low quality media Change to higher quality media Recovery Af
3. addressed by the status of the three indicator lamps are listed bellow READY and MEDIA Lamps blink simultaneously Possible Cause Recommended Solutions Media sensor cannot detect labels a Check and confirm the media has been loaded correctly b Check the position of the media sensor and confirm it could detect the media gap or black line c Calibrate the media sensor Note If using continuous media ensure correct Media Type settings in chosen in the label software Media ran out Load a roll of media Media jammed The Media Roll Guides are not firmly positioned against the Media or have not been installed Clear the jam Install the Media Roll Guides correctly and press them firmly press the media Media sensor is broken Contact an authorized POSTEK service provider for technical support READY and RIBBON Lamps blink simultaneously Possible Cause Recommend Solutions Ribbon ran out Load a new roll of ribbon Ribbon jammed Ribbon Sensor error Clear the jam Contact an authorized POSTEK service provider for technical support Only READY Lamp blinks Possible Cause Recommend Solutions Serial VO error Check DIP switches for the baud rate settings Memory overflow a Restart the printer b Reset the printer 34 Chapter 5 Troubleshooting C168 Series User s Manual Miscellaneous Vertical Blank Lines Appear
4. buttons PAUSE FEED and CANCEL Indicator Lamps The three lamps indicate the status of the printer please refer to Chapter 4 Troubleshooting for error indicators Solid Indicates the printer is in the normal state Blinking Indicates the printer is in the PAUSE state Solid Indicates the printer is in the normal state Blinking simultaneously with READY Running out of media Solid Indicates thermal transfer printing Off Direct thermal printing no ribbon installed Blinking simultaneously with READY Running out of ribbon 28 Chapter 3 Operations and Settings C168 Series User s Manual Panel Buttons The three buttons have different functions based on the mode of the operation is performed y Advanced Functions Mode Basic Functions see Advanced Functions below Feed Calibration Feed one label Media Sensor Calibration Pause Self Test Press once to pause current print job Self test Press a second time to resume printing The printer performs a self test and prints out a configuration report Cancel B Reset Cancel current batch of labels Reset Forces the printer to continue working after Resets the printer to factory default settings an error has been corrected Advanced Functions Media Sensor Calibration It is necessary to accomplish Media Sensor Calibration after a new roll of media has been loaded 1 Press and hold the Feed Calibration button for about 4 sec
5. labels supports the labels as they feed out of the printer The roller can accumulate debris from consumables such as dirt sand dust or glue To ensure longevity of the Platen Roller follow the recommended maintenance guidelines below Clean the Platen Roller after every 3 rolls of label media used To clean the Platen Roller Turn off the printer Open the top cover Release and lift the Printhead Module Remove the ribbon if applicable and media di n Use a cotton swab dipped in anhydrous isopropyl alcohol Rub the swab along the Platen Roller while rotating the roller until the swab no longer accumulates ink or debris Cleaning the Printer Interior Over time the printer s interior may collect dust or debris from the consumables It is advised to periodically clean the printer s interior in order to prevent the accumulated debris from damaging internal parts To clean the printer interior use a cotton swabs dipped into anhydrous isopropyl alcohol and remove any debris Chapter 5 Troubleshooting C168 Series User s Manual Chapter 5 Troubleshooting Occasionally situations occur that require some troubleshooting Possible issues and potential solutions are listed in this section While not every situation is addressed you may find some of these tips useful Error Indications Typically when the printer is not functioning one or two of the three indicator lamps will begin blinking The possible situations
6. 2 Setup and Use C168 Series User s Manual Figure 4 RS232 Serial Port 3 USB Port 5 DC IN Port DIP Switches 4 Ethernet 6 Power Switch Parallel Port Connecting the Printer Warnings 1 Do not use the printer near liquids or corrosive chemicals 2 Using the wrong power adapter may cause damage to your printer POSTEK assumes no liability for any damage in such cases The rating for the printer is 24VDC Make sure the printer is switched OFF Connect the power cord to the Power Adapter Connect the Power Adapter s DC output plug to the DC IN port on the back of the printer PU O Plug the power cord into a live wall outlet Chapter 2 Setup and Use C168 Series User s Manual Interface Connection The C168 supports RS 232 Serial and USB interface connections Note When connecting the C168 Series printer to a computer via the USB interface cable make sure to utilize the same USB port used during the driver installation process which enables the printer to retrieve needed commands or data from the PC If the same USB port is not available or not known then in the printer s Properties Dialogue Box under the Ports tab ensure the current port location is checked To connect Make sure the printer is powered OFF The printer will identify the communication port automatically 3 The default values of printer port can be obtained from the self test report See Chapter 2 Operation Basics Advanced Functions
7. A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures see FCC Notice Static electricity that accumulates on the surface of the human body or other objects can damage the print head or electronic components in the C168 Series printer Observe proper electrostatic safety precautions when handling C168 Series User s Manual Table of Contents E TNT 1 Important Notice Read Me First ccississcessiccssscones rios es se Se sek Oe se Ke ese Ee nee Ge ere ed keer ed pe id ee ene se Ge ees deeg L Chapter 1 Introduccion EE EE Ke Re Gee Se de Ge eg ede ie eg GR GER Ee Ge ee Ke Ge GO ee NE ee Printer NEL US RR AO OR N N EK N OE EE 2 Specifications for Power Adapters ie an vee vk GR vos cede but ode Oe A ene VO Gee BR Ge ee PR oe Ee 2 COntents Of BOX 4er EE EE EO EO EO EG 3 Packing EER RR EE OE OR ER EE AE OR EE EEN ER 3 Chapter 2 Setup nd USt EE Ne iO Settingiup tie Printer is ee in De ee be gee ED Se yes ge ER be N gee er EE ie 5 MainParts and ES el TEG Se EE EE EE 5 Connecting the AAA RON 7 Interface COMO AAA EE ER EE N 8 Eoadine the lede ee EE EE EE EE EE EE 8 Loading the ve EE RE EE OE EE OO OE OE OE tientees ida 14 Standard Mode DE N e e melo 14 Pe l off Mode ER EE ia 19 Cutting Modernitas RE ER OE ER OE EE EE ER EE ER EN 22 Usingsthe External Medid Stand i e RE He titi oO IEC A O EE EA E ENNE 23 Install the Media adi se GE ee Rd ek
8. Adapter 1 pe USB interface cable 1 pe Media Spindle 1 pe Media Roll Guides 2 pcs Media Core Adapters 2 pes Ribbon Spindles 2 pcs Empty Core I pe Quick Start Guide 1 pe CD ROM pack 1 pe Note CD ROM pack includes the printer driver label software C168 Series User s Manual How to install video and Programming Manual Chapter 1 Introduction C168 Series User s Manual C168 Series Printer Power Adapter Ribbon Spindles Media Roll Guides External Media Stand USB Cable Emp Core Figure 1 Printer and Accessories Chapter 2 Setup and Use C168 Series User s Manual Chapter 2 Setup and Use Setting up the Printer Before setting up the printer consider the following 1 Make sure there is adequate space around the printer for loading consumables and proper ventilation 2 Make sure the printer is close to the host so the interface cable is easily accessible at either end Main Parts and Structures 9 3 2 i POST 1 s 6 ie 7 8 Figure 2 1 READY Indicator 4 PAUSE Button 7 Media Exit 2 MEDIA Indicator 5 FEED Button 8 Cover Handle 3 RIBBON Indicator 6 CANCEL Button 9 Top Cover Chapter 2 Setup and Use C168 Series User s Manual Figure 3 1 Printhead Module 5 Platen Roller 9 Ribbon Supply Spindle 2 Printhead Bracket 6 Printhead Release Lever 10 Media Compartment 3 Printhead 7 Media Guide 11 Guide Wheel 4 Media Sensor 8 Ribbon Loading Knob Chapter
9. GE Ee ee Ged ek Ge a O Ee ee a O AA detente 23 Load Media Using External Media Stand sesse ese see ee se se ke ee ee aaa Re ee EEE E O E i ee ee Re ee 24 Adjusting the Position of Media Senso EE SR Ee sie ee Ed ve n De RE de ves De UR en Ede ee EE nino Be Gee Ee SR oue 26 Chapter 3 Operations and SetfingS sesse nesse esse se dese ee dese se ego geo geoes eds vee go secar SR eg Ke doe gee og eg eo dees sesse ZO PO AAA VERS feed ee EE see De oats es ee Ee ee GE De ed ee ER RES oes bee be gues nade jens BOERE aces ES LE DE es 28 EE SU RE 28 Cleaning the Printer Intent Or wis RA N RE EE iaa 33 Chapter 5 Troubleshooting res RSG AE De KG ER Go Gee Seg Ge GE a Error Gie LR EE SES EE EE A RE EE OE EE N OE RR iein 34 EI AAA O AAN 35 Vertical Blank Lines Ns ER AR EE A A EO EE OE EE A TE 35 Printer Timeout Error Message ee Ee ee hin Vee AAA ee Ee Oe Ge De Ed oe ee ves Bed we Ee Ve 35 Data Sentibut NOt GEL EE OE EE OE RE AE EE OR iepstes tee 35 Poor Vee UR OE EE EE OER HO N EE EE 36 IRECOVELY ES RE DE Ee GE DE GR EE OE ED GE De ten tote tes OE DE EE DE ED OR A DE EE EE DO ag 36 Appendix A Interface Specificati0nS sesse Ge Ge GR See RR ROG noe nea GER eg ee be Ge ee se ee dk Ge ee ee ie eed OF C168 Series User s Manual Appendix BASCH Table iii ii a a O Preface Important Notice C168 Series User s Manual Preface Your POSTEK C168 Series compact barcode label printer features innovative technology and superior quality workmanship Boasting
10. POSTEK RUGGED PARTS DURABLE MACHINES User s Manual C168 Series Barcode Label Printer C168 Series User s Manual FCC Notice This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment may generate use and or radiate radio frequency energy If not installed and used in full accordance with this User s Manual interference to radio communications may occur This equipment complies with the limits for a Class A Information Technology Equipment pursuant to Part 15 of the FCC Rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area may also cause interference In such case the user at his her expense will be required to correct the interference using whatever means necessary Trademarks POSTER is a registered trademark by POSTEK Electronics Co Ltd ARM is a registered trademark of Advanced RISC Machines Ltd Microsoft Windows are registered trademarks of Microsoft Corporation Copyright O 2006 2015 by Postek Electronics Co Ltd All rights reserved Under the copyright laws this manual cannot be reproduced in any form without the prior written permission of Postek No patent liabili
11. Self Test Cable configurations for Serial RS 232C interface is found in Appendix A of this guide 5 Please take the following measures to reduce cable noise Restrict the length of the interface cable to less than 6 1 83 M if possible Keep the interface cable separate from power cords Loading the Ribbon Warnings 1 Load ribbon only when using the thermal transfer printing method Remove any ribbon that may be loaded when using the direct thermal printing method 2 When using a ribbon roll with a width less than 110m please place the ribbon roll in the middle of the Ribbon Spindle corresponding to the symmetry symbol l 3 No need to load the ribbon when printing direct thermal media To install the ribbon Lift the top cover and push down the Printhead Release Lever to release the Printhead Module see Figure 5 1 Lift the Printhead Module to expose the ribbon supply spindle see Figure 5 2 Unwrap the ribbon pack and separate the ribbon roll and the core Slide the ribbon onto one of the Ribbon Spindles and place the core onto the other spindle see Figure 5 3 Load the Ribbon Spindle into the printer and route the ribbon through the Printhead Module see Figure 5 4 Wrap the end of the ribbon around the core see Figure 5 5 Load the core into the Ribbon rewinder see Figure 5 6 Turn the guide wheel on the left of the core to take up the loose ribbon and tighten the ribbon ee AA MB P DE Clo
12. a under the media guide rod and above the platen roller Adjust the 2 media guides to the edge of the media See Figure 6 11 Media Guide Sa ae Cover Printhead Module Media Guide Rod Figure 6 11 Chapter 2 Setup and Use C168 Series User s Manual 5 Close the Printhead Module and the top cover See Figure 6 12 Figure 6 12 Chapter 2 Setup and Use C168 Series User s Manual Adjusting the Position of Media Sensor Lift the top cover Push the Printhead Release Lever to release the Printhead Module Lift the Printhead Module to expose the Media Sensor cover see Figure 7 1 Remove the Media Sensor cover and slide the Media Sensor to the appropriate position see Figure 7 3 7 4 and 7 5 A A IDEE Replace the media sensor cover Media Sensor cover Figure 7 1 Media Sensor Figure 7 2 Chapter 2 Setup and Use C168 Series User s Manual 2 5mm Media gap Figure 7 3 Media gap Figure 7 4 Media gap Figure 7 5 Chapter 3 Operations and Settings C168 Series User s Manual Chapter 3 Operations and Settings Basic Operations Power Switch The power switch is on the back panel of the printer The symbols on the switch are defined as follows ON O OFF The Front Panel The Front Panel of the C168 Series printer consists of Three Indicator Lamps MEDIA READY and RIBBON Three multi function
13. a rigid structure a highly reliable motor and transmission system and a large ribbon capacity of 360M users enjoy minimal downtime and low service cost With intuitive operations the C168 is ideal for a wide range of applications This manual explains how to set up and begin using your C168 Series printer It also provides detailed information on configuring your printer basic operations care and troubleshooting Please read this manual carefully before using the POSTEK C168 Series printer Important Notice Read Me First The thermal printhead can be easily damaged due to its precision construction A printhead damaged by misuse is not covered under the terms of the warranty To ensure longevity of the printhead please note the following DO NOT scrape or use tools that might damage the printhead surface To protect from corroding the printhead DO NOT touch the printhead with bare hands DO NOT use thermal paper or thermal transfer ribbons which contain Na K or Cl Keep printhead from any form of liquid or dampness Only use a cotton swab dipped in anhydrous isopropyl alcohol to clean the printhead de a Always use high quality consumables e When the printhead module is closed pressure is placed directly onto the printhead dirt such as paper scraps sand dust and glue can scrape or damage the printhead e The printhead is also easily damaged by static electricity which may be generated by poor quality ribbons 7 Alway
14. dapters onto the Media Spindle first see Figure 6 2 Insert the entire unit into the media compartment in the printer Position the media roll in the middle of the Spindle using the scale for guidance Release and lift the Printhead Module Route the media as shown in Figure 6 3 Slide the Media Guide to the edge of the media Close the Printhead Module and press down until it locks into place see Figure 6 4 Close the cover and press the Feed button to feed the media and ensure proper tracking If the printer does not correctly sense each label it may be necessary to perform the Media Calibration procedure found in the Operation Basics section Chapter 2 Setup and Use C168 Series User s Manual Figure 6 1 Chapter 2 Setup and Use C168 Series User s Manual acs Figure 6 2 Chapter 2 Setup and Use C168 Series User s Manual Figure 6 3 Chapter 2 Setup and Use C168 Series User s Manual Figure 6 4 Chapter 2 Setup and Use C168 Series User s Manual Peel off Mode Note Operating the printer in Peel off mode requires the optional Peeler Kit To load media into the C168 while using Peel off Mode 1 Set the 4 DIP Switch to the ON position to enable the peeler function see Figure 6 5 2 Turn on the printer 3 Reset the Peeler Mo
15. dule Press and hold the Cancel button for 4 seconds until the 3 indicator lamps begin to blink simultaneously Release the Cancel button and press it again one more time Reset is complete 4 Load a roll of ribbon Push the Peeler Module to the Open state Route the media as shown pull the liner to make sure it is tight and then turn the Peeler Module to the Close state Peeler Module installation is complete see Figure 6 6 and 6 7 ON OFF L minin 8 4 9 G VES uu Figure 6 5 Chapter 2 Setup and Use C168 Series User s Manual IE eg Bracket Printhead Module Figure 6 6 Chapter 2 Setup and Use C168 Series User s Manual q N ji E Fa 18 EN eo UT Je ad Liner Path Figure 6 7 Chapter 2 Setup and Use C168 Series User s Manual Cutting Mode Note Operating the printer in Cutting mode requires the optional Rotary Cutter 1 Set the 3 DIP Switch to the ON position to enable the cutter function Turn on the printer Reset the printer Press and hold the Cancel button for 4 seconds until the 3 indicator lamps begin to blink simultaneously Release the Cancel button and press it again one more time The 3 indicator lamps stop blinking and remain lit Reset is complete 4 Load media as shown in Figure 6 8 The Rotary Cutter is now ready to use Pause Self Test eS
16. ed service technicians should attempt to repair the printer Do not place the printer on or near a heat source Be sure that the output of the power adapter is 24VDC and your power source matches the rating listed on the power adapter Be certain your power source is grounded To avoid getting an electric shock do not use a worn or damaged power cord If the power cord becomes damaged or frayed replace it immediately Do not insert anything into the ventilation slots or openings on the printer The printer and power adapter should never be operated in a location where either one can get wet Personal injury may result The printhead becomes hot while printing To protect from damaging the printhead and risk of personal injury avoid touching the printhead To get increased printhead longevity and higher quality printouts always use approved labels tags and thermal transfer ribbons Approved supplies can be ordered from your Postek authorized reseller Static electricity that accumulates on the surface of the human body or other surfaces can damage or destroy the printhead or electronic components in this device DO NOT touch the printhead or the electronic components with bare hands Place the printer on a flat firm solid surface Never operate in a high temperature environment Turn off the power when not in use for extended periods Follow all recommendations and setup instructions included in this manual Warnings This is a Class
17. end data from 2 ports at the same time Data cannot be sent to more than one port simultaneously or data corruption and print errors may occur Appendix B ASCII Table C168 Series User s Manual Appendix B ASCII Table 0 1 2 3 4 5 6 7 0 INUL 0 P p 1 ISOH XON 1 A Q a q 2 STX E 2 B R b r 3 XOFF 3 C S c s 4 4 D T d t 5 NAK 5 E U e u 6 JACK amp 6 F V f v 7 BEL i 7 G W g w 8 IBS 8 H X h x 9 9 I Y i y A ILF J Z j Z B ESC K k C FF lt L 1 l D ICR M m E ISO RS gt N A n F JSI US O E o DEL Note The sign is included in the embedded table at DEC128 or HEX 80 39 POSTEK
18. ngth 984 300 M Fonts Five built in dot matrix ASCII fonts user downloadable TrueType Fonts Bar Code Types 1D Barcode Code 39 Code 93 Code 128 subset A B C Codabar Interleave 2 of 5 UPC A E 2 and 5 add on Media sensor EAN 13 8 128 UCC 128 2D Barcode MaxiCode PDF417 Data Matrix QR Code Reflective Adjustable Transmissive Interfaces RS 232 Serial USB 2 0 Power rating Weight 24 VDC 2 5 A 6 17Ibs 2 8 kgs Dimensions W 9 3 x D 11 4 x H 7 8 inches W 236 x D 291 x H 199 mm Operation environment Temperature 32 F 104 F 0 C 40 C Relative humidity 5 85 non condensing Storage environment Temperature 40 F 140 F 40 C 60 C Relative humidity 5 85 non condensing Optional items Centronics Parallel Interface 10 100Mb Ethernet Rotary Cutter External Rewinder and Media Guide Adaptor Specifications for Power Adapter Input AC 100 240 V 50 60 Hz Output DC 24V 2 5A Environment 0 C 40 C Chapter 1 Introduction C168 Series User s Manual Contents of Box Inspect the shipping carton s for possible shipping damage if damage is discovered notify the shipping company to report the nature and extent of the damage Please check the items according to the Packing List If there are any items missing notify your authorized reseller Packing List C168 Series Printer 1 pc External Media Stand pe Power
19. onds 2 The printer will feed approximately 200mm of media 3 The three indicators stop blinking and remain lit the printer is back to a normal state Self Test 1 Press and hold the Pause Self Test button for about 4 seconds 2 The printer will print out a configuration report and the 3 indicators will stop blinking and remain lit The printer is back to a normal state The following information will be printed on the self test report Font list Hardware configuration and status DIP switch settings Label parameters Firmware version Chapter 3 Operations and Settings C168 Series User s Manual Reset Reset the Printer to the Factory Default Settings 1 Press and hold the Cancel Reset button for 4 seconds the three lamps will blink simultaneously the printer will return to normal state automatically if no operations are performed within 4 seconds 2 Release and press the Cancel B Reset button again 3 The three indicators stop blinking and remain lit The printer is now in its normal state The following parameters have automatically been reset Label Print darkness Speed Others Note The printed label count and printed length may not be reset DIP Switch Panel BENENNEN B Li 9 G v c Note Turn off printer before setting DIP switches Chapter 3 Operations and Settings C168 Series Use
20. r s Manual DIP Bit Functions Remarks i ON Direct thermal print Printing type setting OFF Thermal transfer print Default OFF gt ON Tear off position Stop position setting OFF Edge of next label Default OFF ON Cutter installed Cutter setting i OFF Cutter not installed Default OFF i ON Peeler installed Peeler settings OFF Peeler not installed Default OFF 5 Reserved and not available ON Enable IP setting IP address setup OFF Disable IP setting Default OFF 8 7 7 010 9600 n 8 1 RS232 Serial Port baud rate setting 0 I 1 19200 n 8 1 0 OFF 1 ON 8 110 38400 n 8 1 Default 00 1 1 57600 n 8 1 Please read the content in Important Notice section before setting your printer to direct thermal mode Windows Driver The C168 Series printer driver is packaged with the C168 in the CD ROM pack and is compatible with the following operating systems e Windows 8 e Windows 7 e Windows Vista e Windows NT e Windows XP e Windows 2003 Windows 2000 Windows 98 Windows ME Drivers can also be downloaded from www postek com cn and www postektechnologies com Note Before updating a driver always first remove the old version s that may be loaded on your computer Label Software Each C168 Series printer is packaged with powerful barcode label editing software Note Before downloading the software always first remove any old version that may be loaded on your compu
21. s inspect consumables for high quality before purchasing Note The C168 Series printer functions under Direct Thermal or Thermal Transfer print methods Thermal Transfer is set as the factory default requires ribbon for printing However if you need to print on Direct Thermal materials ribbon is not required please contact your printer supplier or service provider to reduce the printhead pressure This can protect your printhead from early performance deterioration due to direct contact with the thermal media Any physical printhead damage caused by direct thermal printing is not covered under warranty Chapter 1 Introduction C168 Series User s Manual Chapter 1 Introduction Printer Specifications Mode Printing method C168 200s Thermal Transfer C168 300s Printing resolution 203 dpi 8 dots mm 300 dpi 11 8 dots mm Max printing speed 4 ips 101 6 mm 3 ips 76 2 mm s Max printing width 4 25 108 mm 4 17 106 mm Max printing length 157 4000 mm 79 2000 mm Memory 8 MB FLASH ROM 16 MB SDRAM Media Roll feed die cut continuous fan fold tags tickets in plain paper or thermal paper Width 4 33 110 mm max 0 98 25 mm min Supply roll OD 4 102 mm max ID 1 25 4 mm min Thickness 0 003 0 007 0 08 0 18 mm including liner Ribbon Wax Wax Resin Resin Ribbon roll OD 3 76 2 mm max ID 1 25 4 mm core Max width 4 33 110 mm Max le
22. se the Printhead Module and press down until it locks into place Chapter 2 Setup and Use C168 Series User s Manual Figure 5 1 Chapter 2 Setup and Use C168 Series User s Manual Figure 5 2 fo AEO EE ECON Figure 5 3 Chapter 2 Setup and Use C168 Series User s Manual Figure 5 4 Chapter 2 Setup and Use C168 Series User s Manual Figure 5 5 Chapter 2 Setup and Use C168 Series User s Manual le Figure 5 6 Chapter 2 Setup and Use C168 Series User s Manual Loading the Media C168 printers can be operated in three different modes Standard mode Peel off mode or Cutting mode In Standard mode each printed label remains on the backing liner In Peel off mode each printed label is peeled away from the backing liner automatically In Cutting mode the printer automatically cuts the label after 1t is printed Standard Mode To load media into the C168 while using Standard Mode O Al O HER Lift up the top cover to expose the media compartment see Figure 6 1 Load a roll of media labels facing up on the Media Spindle then slide the two Media Roll Guides with smooth sides facing toward the media onto the Media Spindle from each end until snug against the media When placing a roll of media with a 3 ID core please slide the two Core A
23. ter Chapter 4 Maintenance C168 Series User s Manual Chapter 4 Maintenance Warnings 1 Make sure the printer is powered off before performing maintenance operations 2 The Printhead may be hot due to recent printing Wait until the Printhead cools before performing maintenance 3 Use only anhydrous isopropyl alcohol to clean the print head Cleaning the Printhead The Printhead is the mechanism that enables the ink to impact the label Due to the Printheads precision construction and necessary location in the printer it comes into contact with consumables and therefore is susceptible to dirt accumulation If dirt is not removed the Printhead may be damaged To ensure longevity of the Printhead follow the recommended maintenance guidelines below Note A Printhead damaged by misuse is not covered under warranty Clean the Printhead Clean the Printhead after every 1 roll of ribbon use or every 3 rolls of label media use To clean the Printhead Turn printer power off Open the top cover of C168 Series printer Turn the handle to open Remove the ribbon if applicable and media IES Pr RE Use a cotton swab dipped in anhydrous isopropyl alcohol Rub the swab along the Printhead until the swab no longer accumulates ink 8 Let the Printhead dry before using the printer again Chapter 4 Maintenance C168 Series User s Manual Cleaning the Platen Roller The Platen Roller located at the exit point and underneath
24. ter the miscellaneous has been cleared press the CANCEL button to clear the alarm or restart the printer to resume the printing automatically Note For errors not listed here please contact an authorized POSTEK Service Provider for further assistance Appendix A Interface Specifications C168 Series User s Manual Appendix A Interface Specifications The R 232 connector on the printer is a DB9F Pa ON peea N gt TN RTS Connection with host Host 25S Printer 9P Host 9S Printer 9P TR REEN 3RX RX2 ies 2 TX RXS eran 2 TX TX3 aeni 3 RX DSR6 aa 8 DTR DTR4 _ 7 DSR DTR20 naaa 7 DSR DSR6 aaa 8 DTR RTS4 a 4 CTS RTS7 aueia 4 CTS CISS gt atadas 6 RTS CTS S is 6 RTS GNDT7 _ 5 GND GNDS _ 5 GND Alternately you can just connect the 3 wires as follows Host 25S TX 2 Printer 9P Host 9S RE eise 2TX 37 Appendix A Interface Specifications C168 Series User s Manual Baud rate 9600 19200 38400 57600 Data format always 8 data bits 1 start bit and 1 stop bit Parity always non parity Flow control RTS CTS Hardware flow control If you are using software or drivers under the Windows environment the flow control must be set to hardware Any communications port can transmit data from the host RS232 Ethernet or USB Preliminary communications settings are not required since the printer will automatically detect which port is active Note Never s
25. ty is assumed with respect to the use of the information contained herein POSTEK C168 Series Label Printer User s Manual 9th edition January 2015 Disclaimer This manual has been validated and reviewed for accuracy The instructions and descriptions it contains are accurate for the Postek C168 Series label printer at the time of this manual s distribution However succeeding printers and manuals are subject to change without notice Postek assumes no liability for damages incurred directly or indirectly from errors omissions or discrepancies between the printer and this manual Although this manual describes and details many issues which could possibly occur the manufacturer cannot warrant against unpredictable conditions during the printing process For problems such as the printer not working lost or unclear print content etc the manufacturer and resellers are responsible for correcting these issues according to Postek Printer Warranty Clauses In no event shall the manufacturer or the resellers involved be liable for any damages whatsoever including without limitation damages for loss of business profits business interruption loss of business information or other pecuniary loss arising from the use of the results of use or inability to use this product even if the manufacturer has been advised of the possibility of such damages C168 Series User s Manual Important Safety Instructions oe es Only gualified and train
Download Pdf Manuals
Related Search