Siro R - Installation manual
Contents
1. most electrical cookers hobs and ovens meant for household use Traditional cast iron cookers and hobs Ceramic cookers and hobs Induction cookers and hobs Cookers and hobs equipped with a ti mer afterheat indicator child proof lock or integrated switch off system SAFERA Siro R is compatible with cookers no wider than 90 cm see chapter 2 Instal lation step 1 6 1 2 Control Panel Adjustment mode button Indicator light panels Sensor AP ATTENTION If the appliance was stored in a cold spa Pe as ad lock button ce it must be allowed to warm up to room BULLOA lon beco pated whore O orc ndicator light for normal activity Warning light for cooktop hazard HINT O Warning light for water leakage 9 9 O A WARNING Please contact your vendor if you notice anything unusual about the appliance INS ALLATION STEP 1 6 Mount the Sensor unit Install the Cental Unit on the wall above the cooktop and follow these dimensions Installation Height Width k idth Align the Sensor unit 15 Cooker widt mm with the centre of Max 60 cm 45 75 cm the cooktop 60 90 cm 60 75 cm Depth Align the sensor of Sensor unit white lens 100 mm with the centre of the cooktop Min 8 mm iS AR ae 9 KLIK 5 ATTENTION The Sensor unit is plugged into the wall socket with its own power2. SAFERA SAFETY WITH STYLE INSTALLATION MANUAL SAFERA Siro R line stove guard Power control units PCU3 PCU3 W PCU5 1 U PCU5 1 P 20812 V4 5 0 ENG SIRO R LINE CONTENTS 1 Preparations 2 Installation 3 Troubleshooting 4 Optional Installing the Water Leakage Sensor Follow these instructions carefully and pay particular attention to the instructions marked in the following way A WARNING Follow instructions marked with a war ning accurately to prevent injury to per sons and damage to property Hints give you useful advices on using the appliance WARNINGS A WARNING Read user and installation manual before using or installing the appliance Install and check the application accor ding to the instructions SAFERA is not liable for any damages or expenses caused by inappropriate installation Check that the Stove Guard is compatible with the cooker see section 1 1 If the network cable is damaged it must be replaced by the service personnel of the manufacturer or their representative to avoid hazards All electrical connections must be carried out by a qualified electrician 5 ATTENTION 1 PREPARATIONS Check the product and the contents of the package before installation Sensor unit with mounting bracket A Power Supply O Power Control Unit User and Installation Guides Declaration of Conformity 1 1 Compatibility SAFERA Stove Guard is compatible with
3. apter 5 Troubleshooting 4 INSTALLING THE WATER LEAKAGE SENSOR optional Stove Guard can be equipped with max four SAFERA Water Leakage Sensors The sensors are placed in the typical leakage areas e g under the dishwasher or sink Attach the sensors in place Attach the plug O of the leakage sensor to the Power Control Unit 8 If there is an extra sensor its plug is connected to the connector 1 of the previous sensor O Check the operation of the furthest sensor by placing a damp paper to wel against it for 15 seconds When the water is detected the Sensor unit A gives a sound signal the warning light for water leakage O blinks and light panels O blink blue Reset the leakage alarm by pressing the OK button Q Clean and dry the sensor HINT If the sensor is left wet the appliance will give another alarm in an hour after signing off the previous one 15
4. em Connect the power supply to the Sensor unit A indicator light panels O are lit in purple When the indicator light panels start blinking yellow green you need to calibrate the system Choose from the two options OPTION 1 Cooker and oven are connected to the Power Control Unit or OPTION 2 Only cooktop is connected to the Power Control Unit Press the adjustment mode button O indicator light panels O start blinking purple blue Put back the fuses for the cooker and the oven The Power Control Unit will now contact the Sensor unit A which gives a sound signal eee HINT You can re start the installation process anytime by pressing the adjustment mode button for five seconds until you hear the signal 15 Turn on the oven and press the child proof lock button When you hear a sound signal eee turn off the oven Turn on the biggest cooker plate with maximum power and press the OK button O When you hear a sound signal eee turn off the cooker A HINT With induction cooker use a compatible dish Check that the indicator light for normal activity O blinks every five seconds INS LLATION E STEP 5 6 Adjust the alarm limit Check the closest recommended alarm Location of the Cooker Installation Alarm Limit limit from the refe rence table o
5. n move freely A HINT If you are replacing a cooker press the ad justment mode button for five seconds until you hear a signal Continue the installation according to step 3 6 a Mount the power control unit on the wall behind the cooker or into the cabinet next to the cooker Install the power control unit with Perilex connectors Don t reconnect the power to the cooker yet 66mm 146 mm Optional water sensor connection See chapter 4 280 mm 126 mm PCU5 1 U INSTALLATION Fixed 1 phase connection 230V MAX 25A MICRO DISCONNECTION A WARNING Make sure that there is no power supply to the cooker and the oven by removing their fuses Also ensure that the cooker is swit ched off OUT wires are always energized when the power control unit is connected to the electrical network If a wire is loose it must be properly covered Do not install the Power Control Unit to ex cessive heat Operational ambient tempera ture is 5 40 C 5 ATTENTION Install the power control unit so that it is not exposed to moisture Check that all cables can move freely HINT If you are replacing a cooker press the ad justment mode button for five seconds until you hear a signal Continue the installation according to step 3 6 15 Installation O Remove the fuses to the cooker and oven 2 Mount the power con
6. n the right In acorner 12 reacts slowest Height 1 12 75 cm 6 Th is 1 12 oa i e range is 1 12 OO 1 reacts fastest 55 em 8 45cm 9 Next to a wall 5 65cm 6 55cm 7 ele 45cm 8 In an island 75cm 4 65cm 5 OO 55 cm 6 45 cm 7 Default Adjust the alarm limit according to the reference table above The default alarm limit is 6 First go to the adjustment mode Press the adjustment mode button indicator light panels lit white 12 11 10 RPN O SI OO Then adjust the alarm limit Raise the alarm limit 1 press the OK 4 button vakioasetus Lower the alarm limit 1 press the lock button O When you adjust the Color of the indicator Number of AR alarm limit the new light panels beeps alarm limit is indica 12 ted as shown in the table on india the right 9559 oo 11 999 o 10 HINT Red i 999 You may check the alarm limit by pressing the ad 8 justment mode button 7 twice 999 000 6 default 996 66 5 996 6 4 Blue sos 3 ee 2 1 A WARNING Do not set the alarm limit higher than 9 during the installation If the alarm limit is set too high the app liance may fail to detect a hazardous situ ation in time INSTALLATION STEP 6 6 check list Check the working order of the appliance and fill in the installation checkli
7. st All the burners of the cooker cause a child proof lock alarm The oven if connected causes the child proof lock alarm The sound signal is lower than the signal from the cooker child proof lock The child proof lock turns off the oven and all the bur ners The indicator light panels O are not lit red after installation The alarm limit is set according to the cooker location Installation date Installation place Installer 3 INSTALLATION TROUBLESHOOTING Problem Remedy Installation is not proceeding as expected You can re start the installation process anytime by pressing the adjustment mode button for five seconds until you hear the signal and continue from step 3 6 The sensor unit is not responding to any button and none of the indicator lights are lit Ensure that the power supply 0 is connected correctly to the wall socket and that the socket has power None of the cooker plates cause a child proof lock alarm The wireless connection has not been properly made redo the installation starting from step 3 6 The appliance turns off the power from the cooker but the power comes back on immediately Make sure that the Power Control Unit is connected correctly in other words the cooker is connected to the OUT cable If the light panels O are constantly lit red after the installation the appliance is faulty See user manual ch
8. supply INSTALLATION STEP 2 6 Mount the Power Control Unit Install the Power Control Unit according to the following instructions PCU3 PCU5 1 U Fixed 3 phase connection Fixed 1 phase connection See pages 8 9 See pages 12 13 PCU3 W PCU5 1 P Perilex connectors e 3 pin plug See pages 10 11 A See pages 14 15 PCU3 INSTALLATION Fixed 3 phase connection IN O PE PE L N N 1 max doovi0a_ ALL 2 jmaxer vioa ALL L 230V 16A L3 max ov 10A MICRO DISCONNECTION A WARNING Make sure that there is no power supply to the cooker and the oven by removing their fuses Also ensure that the cooker is swit ched off OUT wires are always energized when the power control unit is connected to the electrical network If a wire is loose it must be properly covered If the element voltage of the cooker is 400 V the fuse can only be maximum of 10 A If the element is 230 V the fuse can only be maximum of 16 A Do not install the power control onit to ex cessive heat Operational ambient tempera ture is 5 40 C ATTENTION Power control unit requires a neutral wire to operate Install the power control unit so that it is not exposed to moisture Check that all cables can move freely HINT If you are replacing a cooker press the ad justment mode button for five seconds until you hear a signal Con
9. tinue the installation according to step 3 6 a 2 4 Remove the fuses to the cooker and oven Mount the power control unit on the wall behind the cooker or into the cabinet next to the cooker Couple the protective earth first PE Couple the other wires Don t reconnect the power to the cooker yet IN 5 2 5 mm 0 7 m Optional t OUT water sensor 5x25 mm connection 13m See chapter 4 Installati PCU3 W INSTALLATION pepe 3 phase Perilex connectors O Remove the fuses to the cooker and oven IN O OUT PE PE L N N 1 max Zoovi0a_ ALL 2 meia ALL L 230V 16A L3 max oov 10A MICRO DISCONNECTION A WARNING Make sure that there is no power supply to the cooker and the oven by removing their fuses Also ensure that the cooker is swit ched off OUT wires are always energized when the power control unit is connected to the electrical network If a wire is loose it must be properly covered If the element voltage of the cooker is 400 V the fuse can only be maximum of 10 A If the element is 230 V the fuse can only be maximum of 16 A Do not install the power control onit to ex cessive heat Operational ambient tempera ture is 5 40 C ATTENTION Power control unit requires a neutral wire to operate Install the power control unit so that it is not exposed to moisture Check that all cables ca
10. trol unit on the wall behind the cooker or into the cabinet next to the cooker 3 Couple the protective earth first PE O Couple the other wires O Don t reconnect the power to the cooker yet Optional water sensor connection See chapter 4 IN 3x 4mm OUT 3x4mm PCU5 1 P INSTALLATION 3 pin plug 230V MAX 25A MICRO DISCONNECTION 59 79 mm A A ik 5 E 73mm Y C C 60mm N 68 80 mm ORO O Y M A WARNING 5 ATTENTION Make sure that there is no power supply to the cooker and the oven by removing their fuses Also ensure that the cooker is swit ched off OUT wires are always energized when the power control unit is connected to the electrical network If a wire is loose it must be properly covered Install the power control unit so that it is not exposed to moisture Check that all cables can move freely HINT If you are replacing a cooker press the ad justment mode button for five seconds until you hear a signal Continue the installation according to step 3 6 Connect the stove with 3 pin plug Optional water sensor connection See chapter 4 Don t reconnect the power to the cooker yet INSTALLATION STEP 3 6 Set up the wireless connection INSTALLATION STEP 4 6 Calibrate the syst
Download Pdf Manuals
Related Search