mX-BaseBoard with mX-LPC1114-S
Contents
1. with mX LPC1114 S USER MANUAL 25 03 2011 Improper mounting of the mX LPC1114 S board on mX BaseBoard may damage the mX LPC1114 S board and the mX BaseBoard The GND pin on mX LPC1114 S board should be aligned with the pin 1 of P9 female header on BaseBoard Refer to the marking as shown in the image above Validating the mX BaseBoard Download the workspace as zip form here Download the Binary as zip form here For flashing the Binary files please refer to CooCox CoFlash Quick Start with GUI 1 You need to flash the mX LPC1114 S board with the required firmware according to the functionality 2 The CooCox CoFlash Quick Start with GUI is for Nuvton the same procedure follows for NXP also http shop ngxtechnologies com mX BaseBoard with mX LPC1114 S USER MANUAL v1 0 Led Blink PORTS used PORTO PINS used PIOO_ 7 Schematic net name D2 A sample program to blink is provided flash the mX LPC1114 blinky bin file onto mX LPC1114 S and RESET The LED D2 should start blinking LCD PORTS used PORT2 for Data lines and PORT3 for Control lines PINS used PIO2 6 PIO2 7 PIO2 8 and PIO2 9 for Data lines and PIO3 0 PIO3 1 and PIO3_2 for Control lines Schematic net name LCD D4 LCD D5 LCD D6 LCD D7 LCD EN LCD RW and LCD RS A sample program to LCD is provided flash the mX LPC1114 Icd bin file onto mX LPC1114 S and RESET The LCD should display NGX TECHNOLOGI2. ES SD card PORTS used PORTO for MOSI MISO and SSEL PORT2 for SCK PINS used PIOO 9 PIOO 8 PIO2 11 and PIOO 2 Schematic net name MOSI MISO SSEL and SCK A sample program to SD card is provided flash the mX LPC1114 sdcard bin file onto mX LPC1114 S insert a SD card and RESET On the LCD it should display SD card PASS Remove the card and RESET on the LCD should display SD card FAIL PC PORTS used PORTO for I2C SDA and I2C SCL PINS used PIOO_ 5 and PIOO 4 Schematic net name I2C SDA and I2C SCL A sample program to I C is provided flash the mX LPC1114 i2c bin file onto mX LPC1114 S and RESET The LCD should displays I7C PASS Connected to the IC lines is an EEPROM device The program writes and reads back a piece of data to test http shop ngxtechnologies com 6 mX BaseBoard with mX LPC1114 S USER MANUAL v1 0 25 03 2011 UART PORTS used PORTI for TXD and RXD PINS used PIOI 7 and PIOI 6 Schematic net name TXD and RXD A sample program to UART is provided flash the mX LPC1114 uart bin file onto mX LPC1114 S and RESET Connect the serial cable to J4 and PC serial port Open a HyperTerminal with 115200 baud 8N1 The typed characters on the keyboard are echoed on the HyperTerminal Buzzer PORTS used PORTI for BUZZER PINS used PIO1 11 Schematic net name BUZZER A sample program to BUZZER is provided flash the m
3. X LPC1114 S board The board is a stamp for LPC 1114 mX BaseBoard can be used to extend the features of the stamp by providing connectors and interface to various peripherals of the stamp and provide power to the peripheral interface Features 2x16 with contrast control amp back light SD Card connector Power Jack Power Switch Reset Button ISP Button External Interrupt Button Buzzer PS 2 Serial Connector 0 Preset for ADC On board EEPROM http shop ngxtechnologies com 3 mX BaseBoard with mX LPC1114 S USER MANUAL v1 0 25 03 2011 Getting Started Before starting you would need the following things handy and ready For compiling and debugging programs refer to CoIDE User Guide The CoIDE User Guide is for Nuvton the same procedure follows for NXP The user needs to select the appropriate part number Make sure that you have read the CoIDE user guide carefully before you proceed further Requirement The requirement is put in two sections Hardware e Power adapter rating 7 5 V 1 AMP e SD card e USB mini cable e Serial cable e PS 2 Keyboard Software e PC with Windows OS e Use HyperTerminal as terminal software e mX LPC1114 S CoIDE workspace from NGX Technologies e Flash Magic Setup Mounting the mX LPC1114 S Board The mX LPC1114 S board should be mounted on the mX BaseBoard with a particular alignment DASE DOA Rivi 2 http shop ngxtechnologies com 4 mX BaseBoard
4. X LPC1114 buzzer bin file onto mX LPC1114 S and RESET on the mX BaseBoard a tone is heard from the buzzer The jumper JP1 should be inserted Ext Int PORTS used PORTO for EXT SW PINS used PIOO_ 7 Schematic net name EXT SW A sample program to BUZZER is provided flash the mX LPC1114 exint bin file onto mX LPC1114 S and RESET on the mX BaseBoard the BUZZER toggles between ON and OFF when the button SW6 is pressed ADC PORTS used PORTI for ADC PINS used PIO1 4 Schematic net name ADC A sample program to ADC is provided flash the mX LPC1114 adc bin file onto mX LPC1114 S and RESET vary the pot R14 on the mX BaseBoard The change in value is displayed on the LCD http shop ngxtechnologies com 7 mX BaseBoard with mX LPC1114 S USER MANUAL v1 0 25 03 2011 PS 2 PORTS used PORT2 for PS2 DATA and PS2 CLK PINS used PIO3 4 and PIO3 5 Schematic net name PS2 DATA and PS2 CLK A sample program to PS 2 is provided flash the mX LPC1114_ps2 bin file onto mX LPC1114 S and RESET connect a PS 2 keyboard to mX BaseBoard Type the keys on the keyboard and the corresponding characters are displayed on the LCD ISP Programming On the mX BaseBoard press and hold the ISP switch SW5 then press and release reset switch SW4 then release ISP switch SW5 This put the micro controller in ISP programming mode Using flash magic flash the device Refer below for settings in s
5. ch such NGX Technologies products or services might be or are used Disclaimers Information in this document is believed to be reliable and accurate However NGX Technologies does not give any representations or warranties expressed or implied as to the completeness or accuracy of such information and shall have no liability for the consequences of use of such information NGX Technologies reserves the right to make changes to information published in this document at any time and without notice including without limitation specifications and product descriptions This document replaces and supercedes all information supplied prior to the publication hereof Trademarks All referenced trademarks product names brands and service names are the property of their respective owners http shop ngxtechnologies com 13
6. creen shots Start the Flash Magic tool Step 1 As in the screen shot select the device as LPC 1114 301 Select the com port to which the device is connected Here it is COM 1 Set the baud rate to 38400 Interface to None ISP Set Oscillator MHz to 16 Step 2 Tick mark Erase all Flash Code Rd Prot Step 1 Communications Select Device LP 114 301 Erase block 1 0x001000 0x001FFF COM Port NNI S erase block 2 0x002000 0 002FFFI f Erase block 3 0x003000 Ox003FFF Baud Rate 35400 E Je rase block 4 0004000 0004FFF j intertace None ISP Je Eras block 5 0x005000 0 005FFF l W Erase all Flash Code Rd Prot Uscillator MHz f Erase blocks used by Hex File Erase block 0 0s000000 0s000FFF Step 3 Select the path for the hex file Download mX LPCIII4_blinky zip Step 3 Hex File Hex File ktop N Ge m 11e WS MGS m 1114 blinks E ebugsblink hen Browse Modified Unknown more into Step 4 Tick mark Verify after programming Step 4 Options Step 5 Start wf Very after programming Shark Fil unused Flash F Gen block checksums Execute http shop ngxtechnologies com 8 mX BaseBoard with mX LPC1114 S USER MANUAL v1 0 25 03 2011 Before starting to program in the Options Communications tab Fie I5P Options Tools Help GBoi27AB vEs Aliee Tick mark High Speed Communications Communications Hardware Config Securi
7. e scope of the European Union directives regarding electromagnetic compatibility restricted substances ROHS recycling WEEE FCC CE or UL and therefore may not meet the technical requirements of these directives or other related directives The user assumes all responsibility and liability for proper and safe handling of the goods Further the user indemnifies NGX Technologies from all claims arising from the handling or use of the goods Due to the open construction of the product it is the user s responsibility to take any and all appropriate precautions with regard to electrostatic discharge EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES NGX Technologies currently deals with a variety of customers for products and therefore our arrangement with the user is not exclusive NGX Technologies assumes no liability for applications assistance customer product design software performance or infringement of patents or services described herein Please read the User s Guide and specifically the Warnings and Restrictions notice in the User s Guide prior to handling the product This notice contains important safety information about temperatures and voltages No license is granted under any patent right or other intellectual property right of NGX Technologies covering or relating to any machine process or combination in whi
8. mX BaseBoard with mX LPC1114 S USER MANUAL v1 0 25 03 2011 mX BaseBoard with mX LPC1114 S YEB OF mi LPCLiaGy i wea gaer hea loge scam Ths py AOE M IWGIA eg MINA Rew j a nee eee eee ae Oe oe Role idii LLELLE ina tian aa HEHA i TE hrr C7 s mE E A t I55 1717 Tir ji ITTY ee a 1E USER MANUAL http shop ngxtechnologies com 1 mX BaseBoard with mX LPC1114 S USER MANUAL v1 0 Table of Contents Tntroduction cccccceccsseccsscccscccsccesccessceesccuseceusccusccecceusccuscceusceuscceseseuscs 210 0 1 cc es aa er ew er E A ee E SPUN PALL CO E EE E ETE E ce eae ancan ars REU 1 ag ears se csvas gare E AE E ET E ES PE 1 02 Go ere E EE E EE Mounting the mX LPC1114 S Board cccccccccceeeeeeeeeeeeeeeeeees Validating the MX aSe Oat Cs caccceescanwiessasazadesietansensqiaeseencenmsoleaiaesaentoeseess Cd 1 h0 capeene erent E erat Core Nery renerT nr TTT ee rere IPPO aD sa cesta serene E dese eeasguumse eos tuereguemereasesiea Compiling the Workspace cccccccccccccccccceecececeeeeecececeeeeececeseeeeeeeeeeeeeeeess BC A ANN o EENAA N AEE E S AE E S ADEI E E E E A AMO TATRA OTA eeepc A AA aiei i s http shop ngxtechnologies com mX BaseBoard with mX LPC1114 S USER MANUAL v1 0 25 03 2011 Introduction mX BaseBoard is a new addition to the BlueBoard line from NGX Technologies This board is intended to extend the functionality of the m
9. t Teste Dat tite http shop ngxtechnologies com 10 mX BaseBoard with mX LPC1114 S USER MANUAL v1 0 Schematics mX BaseBoard mX LPC1114 S 25 03 2011 http shop ngxtechnologies com 11 mX BaseBoard with mX LPC1114 S USER MANUAL v1 0 25 03 2011 Appendix Project bin files Ports Used Pins Used Remarks PIOO 7 LED D2 should start blinking on mX PC1114 blinky bin PORTO mX LPC1114 S Information Revision History 12 http shop ngxtechnologies com mX BaseBoard with mX LPC1114 S USER MANUAL v1 0 25 03 2011 version v1 0 author Nagaraj M Baddi Legal NGX Technologies Pvt Ltd provides the enclosed product s under the following conditions This evaluation board kit 1s intended for use for ENGINEERING DEVELOPMENT DEMONSTRATION EDUCATION OR EVALUATION PURPOSES ONLY and is not considered by NGX Technologies Pvt Ltd to be a finished end product fit for general consumer use Persons handling the product s must have electronics training and observe good engineering practice standards As such the goods being provided are not intended to be complete in terms of required design marketing and or manufacturing related protective considerations including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards This evaluation board kit does not fall within th
10. ty Just In Time Code Timeouts afe wt High Speed Communications Maximum Baud Fate 2 0400 Y E Half duples Communications Options Hardware config if Use DTR and RTS to control RST and ISP pin E keep RTS asserted while COM Fort open T1 50 m T2 fioo ms Asset OTR and RTS while COM Port oper Cancel OK Tick mark Use DTR and RTS to control RST and ISP pin Step 5 After this start the programming http shop ngxtechnologies com 9 USER MANUAL v1 0 mX BaseBoard with mX LPC1114 S Compiling the Workspace a directory path where the work space is unzipped and open a blinky workspace Download the workspace from here and unzip it Start the CoIDE and Click Project to open 25 03 2011 o ox C10 O File View Project Flash Debug Search Help i Hri New Project Open Project l Save Project As In CoIDE click on the build or press F7 to build the project File Ocotxon TT View Project Flash Debug Search Help COR Bal Halas Eigr ve Pann 4 Common 7 Build FF MO Cms 4 Boot ic maine ES run the program execution This blinks the D2 on mX LPC1114 S board void Blin After building the project initiate debug to download the program to the target Press F5 to File CooCoxCoIDE i a View Project Flash Debug Search Help CBE Bele ee Ri v i vei a Common start Debug Ctrl FS Le main c 23 M Crisis Core _ void Blini a Boo
Download Pdf Manuals
Related Search