Important Safety Instruction
Contents
1. PIP V POSITION Adjusts the vertically PIP position 0 100 BORDER COLOR adjusts border color of the picture Black or Blue SOUND SOURCE Selects the sound source from either the Main or PIP Main or Sub SWAP Alternates between the main and sub picture INSTRUCTION MANUAL en 17 MOUNTING GUIDE gt Wall mount Installation Option The LCD monitor is suitable for wall mounting by using the VESA 100 standard wall mount not included in the delivery i e 4 M4X10 screws gt Attention You must use four M4x10 screws to assemble this monitor and the wall mount bracket 18 M INSTRUCTION MANUAL BM D SUB CONNECTOR PIN ASSIGNENTS gt PIN ASSIGNMENTS BLUE GROUND Pin 1 RED VIDEO 9 2 GREEN VIDEO 10 SIGNAL CABLE DETECT 3 BLUE VIDEO 11 GROUND 4 GROUND 12 SDA for DDC 5 GROUND 13 H SYNC or H V SYNC 6 RED GROUND 14 V SYNC Y GREEN GROUND 15 SCL for DDC 8 ACCESSORIES Power cord Power adaptor User s manual Cable PC or HDMI Stereo cable Option Remote controller Option NO BD c Batteries Option INSTRUCTION MANUAL meer 19 BEL POWER MANAGEMENT gt POWER CONSUMPTION POWER CONSUMPTION ON POWER OFF gt LED INDICATOR The power management feature of the monitor is comprised of two stages Turned on Blue and turned off Red MODE LED COLOR MONITOR OPE2. like 12 INFO Input mode information display INSTRUCTION MANUAL een 09 CONTROL AND FUNCTIONS C Bottom Key Control 1 SOURCE Y Select input source and move the previous menu 2 MENU Activates and exits the On Screen Display This button can also be used to move previous menu or status 3 4 AUTO V A These buttons allow user to move the sub menu of the activated function AUTO Y Auto geometry adjustment 5 6 VOL Adjust the volume and menu settings 7 0 1 Turns the power ON or OFF There will be a few seconds delay before the display appears 8 LED Turned on blue color Turned off red color 9 IR Sensor Remote controller sensor 10 AM INSTRUCTION MANUAL CONTROL AND FUNCTIONS gt Picture Menu Description All picture sound settings and setup for the monitor can be adjusted in the OSD menu On Screen Display To adjust the OSD screen 1 Press the Menu button to enter the OSD menu 2 Press the lt gt buttons to select the desired option The selected option is highlighted 3 Press the button to enter the submenu for adjusting items 4 Change the value you wish to adjust by using the lt gt buttons 5 Press the MENU button to exit the submenu for adjusting items 6 Press the EXIT button to exit the OSD menu SEBHOGE 5 PICTURE PC CONTRAST D 49 BRIGHTNESS 50 COLOR TEMP gt SCALE lt NORMAL gt PICTURE MO
3. 18 5 21 5 INCH VALUE TFT LCD MONITOR INSTRUCTION MANUAL Please read this manual thoroughly before use and keep it handy for future reference INSTRUCTION MANUAL men 01 EL contents SAFETY INSTRUCTION han 2 3 CAUTIONS siria H 4 FCC RF INTERFERENCE STATEMENT 5 INSTALLATION E 6 CONNECTING WITH EXTERNAL EQUIPMENT eese 7 REMOTE FUNCTIONS e oor reti 8 GONTROLANB FUNCTIONS reperi iier e edenda ct d e erant ta 9 16 MOUNTING GUIDE nel cepa ere da ete tu did cana 17 D SUB CONNECTOR PIN ASSIGNMENTS 2 18 POWER MANAGEMENT ssscscovsccssstcttetacctveccussctassccateieasnttccusacedsccntivensaaneeceiieasiaas 19 SPECIFIGCATIONS 20 TROUBLE SHOOTING rne etit er tci eet tecta 21 This Monitor was Manufactured by ISO 9001 Certified Factory 02 en INSTRUCTION MANUAL SAFETY INSTRUCTION _ Important Safety Instruction Read these instructions Keep these Instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth A OV 45 WN c Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that pr
4. DE USER gt CONTRAST BRIGHTNESS HUE SATURATION SHARPNESS COLOR TEMP NORMAL FULL MID HIGH tt MOVE ADJ EXIT tt MOVE 5 ADJ EXIT gt SCALE gt PICTURE MODE USER gt gt gt AV PICTURE MODE RGB PC PICTURE MODE Function Value CONTRAST BRIGHTNESS Adjusts brightness of the screen 0 100 HUE Adjusts hue of the picture 0 100 SATURATION 2 SHARPNESS COLOR TEMP Adjusts intensity of the image 0 100 Adjusts saturation of the picture 0 100 Adjusts sharpness of the picture 0 100 Adjusts color temp of the picture See table below See table below SCALE Display picture size PICTURE MODE Sets picture mode See table below 3D NR Reduces noise of the picture Off Low Mid High MPEG NR Reduces vibration of the picture 1 Unavailable in RGB PC HDMI and AV 2 Unavailable in RGB PC 3 Unavailable in AV HDMI Off Low High INSTRUCTION MANUAL een 11 CONTROL AND FUNCTIONS 1 COLOR TEMP Cool Gives the white color a bluish tint Normal Gives the white color a neutral tint Warm Gives the white color a reddish tint 2 SCALE Center Sets the image size to Center Normal Sets the image to normal 3 PICTURE MODE User Applies user selected values Brightness Contrast Tint and Sharpness Dynamic Provides enhanced contrast and sharpness Standard Provides standard
5. DUCT UNPLUG THIS PRODUCT FROM THE WALL OUTLET BEFORE REMOVING THE BACK COVER AND SERVICING EMISSION CHARACTERISTICS TESTED BY SEMKO THIS PRODUCT HAS BEEN TESTED AND HAS SHOWN COMPLIANCE WITH THE NATIONAL SPECIFICATIONS SUCH AS SWEDISH MPR 1990 10 MPR II gt NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel gt DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard do not expose the unit to rain or moisture This unit is designed to be used in the office or home Do not subject the unit to vibrations dust of corrosive gases gt KEEP INAWELL VENTILATED PLACE Ventilation holes are provided on the cabinet to prevent the temperature from rising Do not cover the unit or place anything on the top of unit gt AVOID HEAT Avoid placing the unit in direct sunshine or near a heating appliance gt TO ELIMINATE EYE FATIGUE Do not use the unit against a bright back ground and where sunlight or other light sources will shine directly on the monitor INSTRUCTION MANUAL een 05 RF INTERFERENCE STATEMENT NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy a
6. RATION Turned On Blue Normal Operation Turned Off Red Not Operation 20 MM INSTRUCTION MANUAL SPECIFICATIONS 18 5 21 5 LCD Type 18 5 Diagonal AM TFT Active Matrix 21 5 Diagonal AM TFT Active Matrix Pixel pitch mm 0 3 H x 0 3 V Pixel pitch mm 0 24825 H x 0 24825 V Brightness 250cd m Typical Contrast ratio 1000 1 Typical Viewing angle 170 160 H V Response time 5ms Typ on off RESOLUTION H x V 1366x768 60Hz 1920x1080 60Hz FREQUENCY Horizontal 31 64kHz Horizontal 31 80kHz Vertical 56 75Hz Vertical 56 75Hz INPUT SIGNAL VIDEO 2ch input 1 0Vp p 75Q terminated loop through out VGA RGB PC HDMI High Definition Multimedia Interface PC Audio in ACTIVE DISPLAY AREA WxH 409 8mm x 230 4mm 476 64mm x 268 11mm PACKING DIMENSIONS W x D x H 505mm X 130mm X 380mm 565mm X 125mm X 415mm 19 88 X 5 11 X 14 96 22 24 X 4 92 X 16 33 WEIGHT Net 3 1kg 6 83 Ibs Net 3 81kg 8 4 Ibs Gross 4 9kg 10 8 Ibs Gross 5 61kg 12 37 Ibs ELECTRICAL RATINGS 12V 3 5 12V 3 5A 100 240V 50 60Hz 100 240V 50 60Hz gt NOTE Technical specifications are subject to change without notice TROUBLE INSTRUCTION MANUAL en 21 TROUBLESHOOTING GUIDE TROUBLESHOOTING TIP No image on display screen 1 Check that power cord or t
7. ced no the apparatus Minimum distances e g 10cm around the apparatus for sufficient ventilation WARNING To reduce the risk of fire or electric shock do not expose the apparatus to rain or moisture The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE REAR COVER NO USER SERVICEABLE PARTS INSIDE REFER TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of uninsulated dangerous voltage with in the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance 04 INSTRUCTION MANUAL CAUTIONS gt CAUTION The power supply cord is used as the main disconnect device ensure that the socket outlet is located installed near the equipment and is easily accessible gt ATTENTIONN Le cordon d alimentation est utills comme interrupteur g n ral La prise de courant doit tre situ e ou install e a proximit du mat riel et tre facile d acces CAUTION TO SERVICE PERSONNEL POWER SUPPLY CORD IS USED AS MAIN POWER DISCONNECT DEVICE IN THIS PRO
8. cing downward on a soft cloth 2 Assemble the Stand Base into the Stand Body in the correct direction using the included screws in the accessory box Stand Base Stand Body FS4x12 screws 3 Once assembled take the monitor up carefully and face the front side B Positioning your display 1 Adjust the position of the panel in various ways for maximum comfort Tilt Range 3 15 59 INSTRUCTION MANUAL een 07 CONNECTING WITH EXTERNAL EQUIPMENT A Rear Connection A 1 18 5 inch 1 PC AUDIO IN 2 AV1 and AV2 OUT 3 AV2 IN 4 AV1 IN 5 VGA D SUB IN 6 HDMI IN 7 DC 12V IN A 2 21 5 inch 1 PC AUDIO IN 2 AV1 and AV2 OUT 3 AV2 IN 4 AV1 IN 5 VGA D SUB IN 6 HDMI IN 7 DC 12V IN 08 M INSTRUCTION MANUAL EL REMOTE FUNCTIONS B REMOTE CONTROLLER Option 1 POWER 0 Press once to switch on your tv set and again to enter the stand by state 2 MUTE Press once to mute the speakers and again to resume the sound 3 MENU Press to pop up main menu and press again to exit menu VOL Press to increase or decrease the volume A Move up operation lt Move left operation gt Move right operation Not support V Move down operation OK Confirm the selection 0 EXIT Press to exit from the menu selecting 4 5 6 7 8 9 1 function or the program information function 11 INPUT Press to select a signal source input as you
9. contrast and sharpness Soft Provides soft contrast and sharpness 12 AM INSTRUCTION MANUAL CONTROL AND FUNCTIONS gt Sound Menu Description All picture sound settings and setup for the monitor can be adjusted in the OSD menu On Screen Display To adjust the OSD screen 1 Press the Menu button to enter the OSD menu 2 Press the lt gt buttons to select the desired option The selected option is highlighted 3 Press the button to enter the submenu for adjusting items 4 Change the value you wish to adjust by using the lt P gt buttons 5 Press the MENU button to exit the submenu for adjusting items 6 Press the EXIT button to exit the OSD menu EDBHDE SOUND EQUALIZER BALANCE SOUND MODE AVC SURROUND tt MOVE 5 ADJ EXIT t MOVE 5 ADJ EXIT SOUND MENU EQUALIZER MENU Option Function Value EQUALIZER Adjusts equalizer of the sound See table EQ Mode BALANCE Adjusts balance of the sound 50 50 SOUND MODE Applies sound mode user selected User Standar Movie Music AVC Activates AVC function of the sound On or Off SURROUND Activates surround function of the sound On or Off INSTRUCTION MANUAL 13 CONTROL AND FUNCTIONS gt OSD Menu Description All picture sound settings and setup for the monitor can be adjusted in the OSD menu On Screen Display To adjust the OSD screen Press the Menu butto
10. he Monitor have been connected securely into wall outlet or grounded extension cable or strip 2 Power switch should be in the ON position and LED is it 3 Check that the Brightness and or the Contrast adjustments of the Display have not been turned down to minimum levels NO SIGNAL message on screen 1 The signal cable should be completely connected to the video card computer 2 The video card should be completely seated in its slot and the computer is switched ON Display image is not centered to small or to large in PC mode Push the down key in front side or Auto key in remote controller Vertical or Horizontal noise is present in the picture Adjust Clock and Phase in the OSD WEEE Symbols Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how t
11. he submenu for adjusting items 6 Press the EXIT button to exit the OSD menu NE N FF gt CURRENT TIME ADVANCE gt TURN OFF TIME IMAGE REVERSE OFF gt TURN ON TIME TIMER MODE SLEEP TIMER TIMER 1 MOVE ADJ EXIT MOVE ADJ EXIT ADVANCE MENU TIMER MENU Option Function Value SLEEP TIMER Activates sleep timer function and applies user selected time Off 15 60min TIMER Sets the timer so that the monitor turns itself on off See table Timer menu IMAGE REVERSE Activates the image reverse function Off H Filp V Filp Reverse INSTRUCTION MANUAL men 15 E CONTROL AND FUNCTIONS gt Geometry Menu Description All picture sound settings and setup for the monitor can be adjusted in the OSD menu On Screen Display To adjust the OSD screen 1 Press the Menu button to enter the OSD menu 2 Press the lt gt buttons to select the desired option The selected option is highlighted 3 Press the button to enter the submenu for adjusting items 4 Change the value you wish to adjust by using the lt gt buttons 5 Press the MENU button to exit the submenu for adjusting items 6 Press the EXIT button to exit the OSD menu BOSSE GEOMETRY H POSITION V POSITION CLOCK PHASE AUTO MOVE ADJ EXIT GEOMETRY MENU Option Function H POSITION Adjust the image position horizontally V POSITION Adjust the image position vertically CLOCK Adjusts the number of vertical pictu
12. hey can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal P N L39ME0399 Rev 0
13. n to enter the OSD menu Press the lt gt buttons to select the desired option The selected option is highlighted Press the button to enter the submenu for adjusting items Change the value you wish to adjust by using the lt gt buttons Press the MENU button to exit the submenu for adjusting items Press the EXIT button to exit the OSD menu pje OSD LANGUAGE lt ENGLISH OSD H POSITION OSD V POSITION OSD DURATION OSD HALFTONE MEM RECALL AARON t MOVE ADJ EXIT OSD MENU Option Function Value OSD LANGUAGE Set the language of the OSD menu English Chinese OSD H POSITION Adjusts the horizontally OSD position 0 100 OSD V POSITION Adjusts the vertically OSD position 0 100 OSD DURATION Adjusts the OSD duration 5 60 OSD HALFTONE Adjusts the OSD half tone 0 50 MEM RECALL Resets the monitor settings to the factory default ee INSTRUCTION MANUAL CONTROL AND FUNCTIONS gt Advance Menu Description All picture sound settings and setup for the monitor can be adjusted in the OSD menu On Screen Display To adjust the OSD screen 1 Press the Menu button to enter the OSD menu 2 Press the lt gt buttons to select the desired option The selected option is highlighted 3 Press the button to enter the submenu for adjusting items 4 Change the value you wish to adjust by using the lt gt buttons 5 Press the MENU button to exit t
14. nd if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Only shielded interface cable should be used Finally any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment gt DOC COMPLIANCE NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio interference regulation of Canadian Department of communications 06 M INSTRUCTION MANUAL TL INSTALLATION Before setting up the monitor ensure that the power to the monitor and other attached devices are turned off X Notice Stand amp screws are optional A Connecting the stand 1 Place the monitor with its front fa
15. oduce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug Apolarized plug has two blades with one wider than the other Agrounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replace ment of the bsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachment accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped INSTRUCTION MANUAL een 03 INSTRUCTION _ The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be pla
16. re elements PHASE Adjusts the number of horizontal picture elements AUTO Adjusts the image position automatically 1 Unavailable in HDMI and AV 16 MM INSTRUCTION MANUAL CONTROL AND FUNCTIONS gt PIP Menu Description All picture sound settings and setup for the monitor can be adjusted in the OSD menu On Screen Display To adjust the OSD screen 1 Press the Menu button to enter the OSD menu 2 Press the lt gt 3 Press the bu buttons to select the desired option The selected option is highlighted tton to enter the submenu for adjusting items 4 Change the value you wish to adjust by using the lt gt buttons 5 Press the MENU button to exit the submenu for adjusting items 6 Press the EXIT MULTI WINDOW SUB SOURCE SIZE PIP H POSITION PIP V POSITION SOUND SOURCE SWAP MOVE Option button to exit the OSD menu Main Sub AV1 or AV2 RGB PC or HDMI Available combination RGB PC or HDMI AV1 or AV2 Unavailable RGB PC or HDMI RGB PC or HDMI combination ADJ EXIT AV1 or AV2 AV1 or AV2 PIP MENU SUB SOURCE TABLE Function Value MULTI WINDOW Activates the PIP feature Off PIP POP Full SUB SOURCE Selects the input source for the PIP area AV1 AV2 SIZE Selects the size of PIP screen Large Small Middle PIP H POSITION Adjusts the horizontally PIP position 0 100
Download Pdf Manuals
Related Search