JUKI-730 Ver.3.0 386SX with LCD/CRT & 4COM
Contents
1. System Memory DRAM The system DRAM on board is divided into two banks bank 0 and 1 The Bank 0 is the on board optional 4MB DRAM Bank 1 is the one 72 pin SIMM Based on the chipset function the 72 pin SIMM only support single side DRAM There have two jumpers for the related setting e JP1 JP2 4MB DRAM and 72 pin SIMM selection Function JP1 JP2 On Board 1MB CLOSE CLOSE 72 pin SIMM OPEN OPEN 2 4 Watch Dog Timer The Watch Dog Timer is enabled by reading port 443H It should be triggered before the time out period ends otherwise it will assume the program operation is abnormal and will issue a reset signal to start again or activate NMI to CPU The Watch Dog Timer is disable by reading port 043H The Watch Dog Timer time out period can be set 1 2 10 20 110 or 220 sec by jumper JP16 e JP18 Watch Dog Active Type Setting JP18 DESCRIPTION 2 3 RESETWHENWDTTIME OUT ___ 4 2 ACTIVATE NMI TO CPU WHEN WDT TIME OUT OPEN DISABLE WDT e JP16 WDT TIME OUT PERIOD OPEN OPEN OPEN 220sec 2 5 DiskOnChip Flash Disk The DiskOnChip Flash Disk Chip DOC is produced by M Systems The DOC MD 2200 xMB is 32 pin DIP package Because the DOC is 100 compatible to hard disk and DOS Customer don t need any extra software utility It is just plug and play easy and reliable Right now the DOC is available in 2MB to 72MB capacity e JP19 DiskOnChip Memory2. be not working Appendix B Watch Dog Timer The Watch Dog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that caused the CPU to crash This condition may have occurred by external EMI or a software bug When the CPU stops working correctly hardware on the board will either perform a hardware reset cold boot or a non maskable interrupt NMI to bring the system back to a known state 24 The Watch Dog Timer is controlled by two I O ports 443 Read Enable the refresh the Watch Dog hex Timer Disable the Watch Dog Timer hex To enable the Watch Dog Timer a read from I O port 443H must be performed This will enable and activate the countdown timer which will eventually time out and either reset the CPU or cause an NMI depending on the setting of JP18 To ensure that this reset condition does not occur the Watch Dog Timer must be periodically refreshed by reading the same I O port 433H This must be done within the time out period that is selected by jumper JP16 A tolerance of at least 30 must be maintained to avoid unknown routines within the operating system DOS such as disk I O that can be very time consuming Therefore if the time out period has been set to 10 seconds the I O port 443H must be read within 7 seconds Note when exiting a program it is necessary to disable the Watch Dog Timer otherwise the system will reset Appendix C Panel Support List Th
3. display the options available for a particular configuration features All the items on the left side of the screen are very common they will not be mentioned here Here we just focus on some special items which are in ROCKY 318 board only These items are specified as following 22 n board IDE Controller The IDE hard disk drive can be Enable or Disable by this item When you do not need hard disk the IDE controller can be disabled n board Floppy Controller The floppy disk drive can be Enable or Disable by this item When you do not need floppy disk the FDD controller can be disabled Serial Port 1 The options are Disable 3E8 2F8 or 3F8 You can set the I O address of the serial port COMA or disable it Serial Port 2 The options are Disable 2E8 3F8 or 2F8 You can set the I O address of the serial port 1 COMB or disable it Parallel Port The options are Disable 3BC 378 or 278 You can set the I O address of the parallel port or disable it Parallel Port Mode ROCKY 318 provides EPP ECP ECP EPP and Normal Mode Primary Display You could set VGA EGA CGA40x25 CGA80x25 Mono or Absent When set Absent the ROCKY 318 will not check the display adapter when power on the system System Keyboard You could set Present or Absent When set Absent the ROCKY 318 will not check the display adapter when power on the system Appendix A ES Key Function The JUKI 730 provides an outstanding E KEYTMunction
4. the total two connector s 5V 12V output e JP9 JP29 COM3 CN1 Pin 9 RI signal or 5V 12V output selection Function JP9 JP29 RI Signal 2 3 1 2 5V 1 2 1 2 12V 1 2 2 3 12 13 e JP8 JP10 COM4 CN2 Pin 9 RI signal or 5V 12V output selection Function JP8 JP10 RI Signal 2 3 1 2 5V 1 2 1 2 12V 1 2 2 3 Connection This chapter describes how to connect peripherals switches and indicators to the JUKI 730 board You can access most of the connectors from the top of the board while it is installed in the chassis 3 1 Floppy Disk Drive Connector JUKI 730 board comes equipped with a 34 pin daisy chain driver connector cable The detailed pin assignment of the connector is specified as following table e CN5 FDC CONNECTOR PIN NO DESCRIPTION Te wo DESCRIPTION CURRENT 6 Ne 8 OL INDEX _ 9 GROUND 14 3 2 IDE Disk Drive Connector You can attach two IDE Integrated Device Electronics hard disk drives to the JUKI 730 internal controller The board comes equipped with a 40 pin flat cable connector The detailed pin assignment of the connector is specified as following table e CN4 IDE Interface Connector 6 DATAQ sid 8 fDATAi0 I 9 fDATA4 25 f10r I 3 3 Parallel Port This port is usually connected to a printer The JUKI 730 includes an on board parallel port accessed through a 26 pin flat cable connector
5. Address Setting Address 1 2 3 4 5 6 CE000 CLOSE OPEN OPEN D6000 OPEN CLOSE OPEN DEOOO OPEN OPEN CLOSE 2 6 BIOS Flash Chip Vpp Setting There have two type of Flash chip are possible to be installed one is 5V Vpp and another one is 12V Vpp 10 The Vpp is supplied when do the programming function Function JP24 5V Vpp 2 3 12V Vpp 1 2 2 7 Clear CMOS Setup If want to clear the CMOS Setup for example forgot the password you should clear the setup and then set the password again you should close the JP13 about 3 seconds then open again Then take Set back to normal operation mode take off the jumper If the RTC Chip is Dallas DS12B887 you should do the procedure when the board is power on e JP13 Clear CMOS Setup Reserve Function DESCRIPTION Normal Operation OPEN CLOSE Clear CMOS Setup 11 2 8 COM3 CN1 RS232 422 485 Setting The COM3 can be set in RS232 or RS422 RS485 interface by the Jumper JP20 JP23 If choose RS422 485 then will need the JP21 to set again for RS422 or RS485 e JP23 COM3 RS 232 or RS 422 485 setting JP23 JP20 1 9 close 3 10 close 5 11 close 7 12 close RS 422 1 2 close 1 2 or 3 4 close RS 485 5 6 close 7 8 close 2 9 COM3 COM4 RI Pin Setting The COM3 and COM4 can supply 5V or 12V power to the serial devices via RI pin Pin 9 of the COM port connector The max current is 1A with fuse protection for
6. C 104 Connection Kit 3 10 LCD Interface Connector The JUKI 730 provides a 2x22 pin connector for the LCD flat panel interface e CN20 LCD Interface Connector PINNO DESCRIPTION PINNO DESCRIPTION 12V GND Mmo 1 38 fiP 44 tv I AMI BIOS Setup 20 The JUKI 730 use AMI BIOS for system configuration and the AMI BIOS setup program is designed to provide maximum flexibility in configuring the system by offering various options which may be selected for end user requirements This chapter is written to assist you in the proper usage of these features 4 1 Getting Start When the system is powered on the BIOS will enter the Power On Self Test routines These routines will be executed for System Test and Initialization and System Configuration Verification After the POST routines are completed the following message appears Hit lt Del gt if you want to run SETUP To access AMI BIOS Setup program press lt Del gt key 4 2 Standard CMOS Setup Standard CMOS Setup is the first option on the main menu The standard CMOS setup utility is used to configure the following features Bate Time Bard Disk Type Eloppy Disk Type All of these features are almost the same as common so we do not describe more detailed in here 4 3 Advanced CMOS Setup 21 When you enter the Advanced CMOS Setup this Setup program is equipped with a series of help screens accessed by lt F1 gt key which will
7. CN12 The detailed pin assignment of the connector is specified as following table e CN12 Parallel Port Connector 15 PIN DESCRIPTION PIN DESCRIPTION NO NO 6 DATA4 _ _ 8 DATA6 _ _ 9 DATAZ _ po 3 4 Serial Ports The JUKI 730 offers two high speed NS16C550 compatible UARTs with Read Receive 16 byte FIFO serial ports These ports let you connect to serial devices or a communication network One DB 9 connector and thee 10 pin headers are provides by the JUKI 730 The detailed pin assignment of the connectors are specified as following tables e COM1 CN17 Serial Port Connector PINNO DESCRIPTION _ 6 DATASET READY DSR 8 GLEARTOSEND CTS 8 RINGINDIGATOR RI e COM2 CN14 2x5 pin Header at RS 232 mode 16 3 5 IrDA Infrared Interface Port The JUKI 730 built in IrDA port which support Serial Infrared IR or Amplitude Shift Keyed IR ASKIR interface When use the IrDA port have to set SIR or ASKIR model in the BIOS s COM2 setup Then the normal RS 232 COM2 will be disabled e CN6 IrDA Connector PIN NO DESCRIPTION 3 6 Keyboard Mouse Connector 17 The JUKI 730 provides two keyboard connectors A 5 pin header connector CN18 supports passive backplane applications Another one is a 6 pin Mini DIN connector CN19 on the board mounting bracket for single board computer applications e CN18 5 pin Header Keyboard Connector KEYBOA
8. JUKI 730 Ver 3 0 386SX with LCD CRT amp 4COM SBC Copyright 1998 All Rights Reserved Manual second edition Aug 01 1998 The information in this document is subject to change without prior notice in order to improve reliability design and function and does not represent a commitment on the part of the manufacturer In no event will the manufacturer be liable for direct indirect special incidental or consequential damages arising out of the use or inability to use the product or documentation even if advised of the possibility of such damages This document contains proprietary information protected by copyright All rights are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer Trademarks JUKI 730 is registered trademarks of Acquire Inc PC 104 is trademarked of PC 104 Consortium IBM PC is a registered trademark of International Business Machines Corporation Intel is a registered trademark of Intel Corporation AMI is registered trademarks of American Megatrends Inc Other product names mentioned herein are used for identification purposes only and may be trademarks and or registered trademarks of their respective companies Contents 1 and te ele 3 2 SAO 6 Ree le e H 13 d AMI BIOS Getup ee 20 Appendix A EKEY FUNCHOM WE 22 Appendix B Watch Dog Tmer 24 Appendix C Panel Support et 25 Introduction Welc
9. Q3287 or equivalent chip and quartz oscillator 128B CMOS memory powered by lithium battery for over 10 years of data retention Memory RAM memory 512KB to 32MB only support single side 16 bit SIMM Shadow RAM memory System BIOS 0F0000h OFFFFFh LCD CRT Interface Chipset HM86508 Resolution Support up to 800 x 600 resolution for STN and TFT LCD Flat Panel And Support 1024x768 256 colors for CRT display Display Memory 1MB on board Input Output IDE hard disk drive interface Supports up to two IDE hard disk drives Can be disabled by BIOS Setup Floppy disk drive interface Supports two 2 88 MB 1 44MB 1 2MB 720KB or 360KB floppy disk drives Can be disabled by BIOS Setup Two high speed Series ports NS16C550 compatible UARTs with send receive 16 byte FIFOs data rates are independently programmable from 115 2K baud down to 50 baud Modem control circuitry Multi mode Parallel Port 1 2 Standard mode IBM PC XT PC AT PS 2 compatible bi directional parallel port Enhanced mode Enhanced parallel port EPP compatible with IEEE 1284 specification High speed mode Microsoft and Hewlett Packard extended capabilities port ECP compatible with IEEE 1248 specification Industrial features Watch dog timer can be set by 1 2 10 20 110 or 220 seconds period Reset or NMI was generated when CPU did not periodically trigger the timer Your program use hex 043 and 443 to control the
10. RD CLOCK KEYBOARD DATA GROUND e CN19 16 6 pin Mini DIN Keyboard Mouse Connector 4 V 0 Cd KEYBOARD CLOCK MOUSE CLOCK N C N C 3 7 External Switches and Indicators There are many external switches and indicators for monitoring and controlling your CPU board These features are completely optional install them if you need them The detailed pin assignment of the connectors is specified as following table e CN7 RESET BUTTON PIN NO DESCRIPTION EXTERNAL RESET GROUND e CN11 IDE LED connector 5V HDD ACTIVE d e CNS POWER LED amp KEYLOCK 18 3 8 External Power Connector The JUKI 730 has an on board external power connector CN13 You can connect power directly to the CPU board for some single board computer without passive backplane application e CN13 EXTERNAL POWER CONNECTOR PIN NO DESCRIPTION EE nl 12V 5V GROUND GROUND SV 7 AN S sv 3 9 External Speaker The JUKI 730 has its own buzzer you also can connect to the external speaker through the connector CN3 e CN3 SPEAKER GROUND SPEAKER SIGNAL 3 9 PC 104 Connection Bus The JUKI 730 s PC 104 expansion bus let you attach any kind of PC 104 modules The PC 104 bus is already become the industrial embedded PC bus standard so you could easily install over thousands of PC 104 modules from hundreds of venders in the world 19 NOTE JUKI 730 allows directly plug in PC 104 module don t need P
11. e JUKI 730 supports a wide range flat panels The different flat panel will need different LCD drive BIOS The default setting is for Color DSTN flat panel The available BIOS for different panels are in the following list Please note all the BIOS files already included the system BIOS and LCD drive BIOS customer only need to re program the BIOS flash chip with the file then power on again 26 MLCD ROM BIOS for MONO DSTN 640x480 For example HOSIDEN HLM6667 HITACHI LMG5160XUFC CASIO MD650TS00 01 OPTREX DMF 50260NFU FW 8 DSTN ROM BIOS for Color DSTN 640x480 For example SANYO LCM 5331 22NTK SHARP LM64C35P TFT S1 ROM BIOS for TFT 640x480 SYNC 16 bit TFT S2 ROM BIOS for TFT 640x480 SYNC 18 24 bit For example HITACHI TX26D60 TX24D55 TOSHIBA LTM09C015A SHARP LQ10D321 TFT LP1 ROM BIOS for TFT 640x480 LP 16 bit TFT LP2 ROM BIOS for TFT 640x480 LP 16 24 bit For example TOSHIBA LTM09C015A TFT86 S1 ROM BIOS for TFT 800x600 SYNC 16 bit TFT86_S2 ROM BIOS for TFT 800x600 SYNC 18 24 bit For example NEC NL8060AC26 05 NEC NL8060AC26 04 NEC NL8060BC31 02 EL ROM BIOS for EL 640x480 For example PLANAR EL640 480 A PLASMA ROM BIOS for PLASMA 640x480 For example PANASONIC S817 How to update the BIOS by yourself 1 Use EPROM Programmer setting the right Flash type and then write the file into the Flash To use this method you should carefully take the Flash chip out of socket and then put it back after finish the pr
12. for system integrator Based on the E KEYTMou could free to store the ID Code Pass Word or Critical Data in the 1Kbit EEPROM 23 Because the EEPROM is nonvolatile memory you don t have to worry the losing of the very important data Basically the E KEY s based on a 1Kbit EEPROM which is configured to 64 words from 0 to 63 You could access read or write each word at any time When you start to use the E KEY W ou should have the utility in the package The software utility will include four files as follows README DOC E2KEY OBJ EKEYDEMO C EKEYDEMO EXE The E2KEY OBJ provides two library function for user to integrate their application with E KEYTMunction These library read e2key and write e2key are written and compiled in C format Please check the following statement then you will know how to implement it easily unsigned int read_e2key unsigned int address This function will return the E KEY s data at address The address range is from 0 to 63 Return data is one word 16 bits void write_e2key unsigned int address unsigned data This function will write the given data to E KEY at address The address range is from 0 to 63 The data value is from 0 to Oxffff To easy start to use the function please refer the include EKEYDEMO C code at first Please note the E7KEY unction is based on the working of parallel port So you should enable the ROCKY 318 s parallel port otherwise will
13. ogramming Usually the flash type is ATMEL AT29C010A Or 27 2 There also have a utility FLASH634 COM and directly re program the BIOS under DOS For example C gt FLASH634 MLCD ROM
14. ome to the JUKI 730 386SX with LCD CRT 4COM Single Board Computer The JUKI 730 is an ISA with PC 104 form factor board which comes equipped with ALI 6117 includes 386SX CPU and advanced high performance multi mode I O designed for the system manufacturers integrators or VARs that want to provide all the performance reliability and quality at a reasonable price An advanced high performance super AT I O chip Windbond W83877F and SMC FDC37C669 are used in the JUKI 730 board Both on chip UARTs are compatible with the NS16C550 And one COM port can be set in RS232 RS422 or RS485 The parallel port and IDE interface are compatible with IBM PC AT and XT architecture s as well as EPP and ECP The LCD CRT controller is HMC HM86508 which can provide the LCD and CRT display at the same time The LCD interface connector is a 44 pin 2 0mm pitch type The most outstanding feature in the JUKI 730 is built in PC 104 expansion bus Based on the PC 104 bus you could easily install over thousands of PC 104 modules from hundreds vendors in the world The JUKI 730 has external power connector that could let it connects with power supply directly It is more suitable for your standalone applications 1 1 Specifications The JUKI 730 386SX with LCD CRT 4COM Single Board Computer provides the following specification System CPU ALI 6117 includes 386SX CPU DMA channels 7 Interrupt levels 15 Real time clock calendar DS12887 B
15. watch dog and generate a system reset PC 104 expansion bus A 64 pin and 40 pin industrial embedded PC bus standard External power connector 8 pin male connector Molex 6410 series compatible Keyboard connector A 5 pin header on board and 6 pin mini DIN keyboard connector is located on the mounting bracket General Power Consumption 5V 1 53A 40MHz 8MB RAM Operating Temperature 0 55 C Humidity 5 95 non condense Dimension 180mm W x 122mm L standard AT form factor What You Have In addition to this User s Manual the JUKI 730 package includes the following items JUKI 730 386SX with LCD CRT 4COM Single Board Computer RS 232 Printer Cable amp RS 232 x 2 Cable FDD HDD Cable 6 pin Mini Din to 5 pin Din Keyboard Adapter Cable Installation This chapter describes how to install the JUKI 730 At first the layout of JUKI 730 is shown and the unpacking information that you should be careful is described The jumpers and switches setting for the JUKI 730 s configuration such as CPU type selection system clock setting and interrupt IRQ setting for serial ports and parallel port are also included 2 1 JUKI 730 s Layout lt reference next page gt 2 2 CPU Setting for JUKI 730 Ver 3 0 e CPU SPEED SETTING The system clock is generated by the AV9155C 02 and the different CPU clock frequency can be selected by JP3 and shown as following table CLOSE OPEN OPEN 2 3
Download Pdf Manuals
Related Search