user manual - Brother, Brother & Sons
Contents
1. 06 LEDONARDO 1 USER MANUAL 1 Remove the two screws holding the cable strain relief and pull the cable thorugh the side of the lamp housing 2 Remove the two srews holding the on off switch box 3 Remove the screw holding the two earth ground wires on the side of the lamp housing O Remove the four screws on the side near the bottom of the lamp housing O Mount the bottom frame with four Philips PH2 screws and 4 serrated washers as shown Note the notch in the bottom frame is on the same side as the focus handles WWW BROTHERS SONS DK user manual rev 1 06 LEDONARDO 1 USER MANUAL Wirepulley Note Remember to insert the guide bar with the correct orientation Place the LED Heatsink part on the remaining guide bar and the wirepulley Insert the guide bar we took out in step 2 and apply the 4 locking rings again O With the cable assembly hanging to the side place the LED assembly in the controlbox assembly as shown O Connect the LED cable and the fan cable as shown Approx 8 mm 0 31 loose cable Strap them on to the LED assembly with the supplied cable tie as shown leaving a small amount of slack on LED side of the cable tie WWW BROTHERS SONS DK H user manual rev 1 06 LEDONARDO 1 USER MANUAL 10 Raise the LED assembly approx 5 mm 0 2 by inserting e g a screwdriver in both ends Lower the Main housing on to the Ledonardo as shown and turn it 90 coun2. LE DON AR DO I USER MANUAL O BROTHER BROTHER amp SONS ApS user manual rev 1 06 LEDONARDO 1 USER MANUAL INTRO Brother Brother amp Sons ApS The information in this manual is subject to change without notice Go to www brothers sons dk for the latest version Brother Brother amp Sons ApS assumes no responsibility for any errors or inaccuracies that may appear in this manual All information and graphics are the property of Brother Brother amp Sons Aps User Manual Version December 2011 Customer and Warranty service Contact your regional dealer Contact information for your area can be found at www brothers sons dk RMA When returning an item please enclose a Model and Serial number b A description of the problem c The name of the owner of the equipment d If available please include a copy of your invoice to establish the date of sale and the beginning of the warranty period Disposing of this product Help preserve the environment Ensure that this product is recycled at the end of its life This product is in compliance with the RoHS and WEEE directives In compliance with EMC standards EN 55103 1 amp EN 55103 2 EN 55022 EN 55103 1 Annex A EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55103 1 EN 61000 4 2 EN 61000 4 3 EN 61000 4 4 EN 61000 4 5 EN 61000 4 6 EN 55103 1 Annex B EN 55103 1 Annex A EN 61000 4 1 1 Brother Brother amp Sons ApS The information in this manual is sub
3. RDO J El 276 mm 10 87 Complete o o Controlbox assembly f d LED assembly 12 x Philips PH2 Screws A A A es 12 x Serrated washers 00000000000 LEDonardo 1 LED Light Engine A WWW BROTHERS SONS DK user manual rev 1 06 LEDONARDO 1 USER MANUAL RETROFITTING CAUTION To avoid damage to equipment take electrostatic precautions when performing the conversion Disconnect fixture from power and allow it to cool for 10 min Conversion should only be performed by qualified personel Tools needed to perform the conversion Phillips PH screwdriver Allen Umbraco key size 2 Slotted srewdriver size 3 3 5 WWW BROTHERS SONS DK user manual rev 1 06 LEDONARDO 1 USER MANUAL Unscrew the four screws as illustrated Note You need to turn the lamp housing 90 when taking it out O NOTE The guide bar is not symmetrical so it is recommended to mark one end to make sure that you remount it correctly Not doing so will affect the optical system Using a screwdriver remove the four locking rings on the guide bar Slide the guide bar out and lift up the lampsocket reflector part Be carefull not to loose the locking rings as you will need them later O Remove the screw on the side of the socket to detach the earth ground wire Loosen the to screws in the bottom of the socket to detach the power cable WWW BROTHERS SONS DK 6 user manual rev 1
4. e operation Using the navigation buttons and display readout refer to the Software Menu chapter navigate to Manual and set the desired intensity additional operations see Software Menu chapter DMX operation Connect a DMX cable Navigate to Address mode Addr and set the desired address resolution response strobe curve settings and in Personality PErS set the desired Fan No DMX and Display settings refer to the Software Menu and DMX Protocol chapters Connect to DMX controller refer to the DMX Protocol chapter Use it WWW BROTHERS SONS DK 4 O user manual rev 1 06 LEDONARDO 1 USER MANUAL AC Power This fixture must be connected to ground Electrical AG Power 100 240 V nominal 50 60 Hz Powersupply Electronic switchmode Max power consumption 132 w DMX Data link This product uses a 5 pin XLR for dmx input and output Use a Shielded data cables Do not overload the daisy chain Up to a maximum of 32 devices can be used on a single dmx chain DMX Channels 1 at 8bit Dimmer 2 at 8bit Dimmer w strobe 2 at 16bit Dimmer 3 at 16bit Dimmer w strobe Protocol USITT DMX512 A SOFTWARE UPDATE Software can be updated via DMX512 with UPLOADER from Brother Brother amp Sons ApS and the latest software version can be found on www brothers sons dk WWW BROTHERS SONS DK 1 1 user manual rev 1 06 LEDONARDO 1 sorwarevers 13 00 USER MANUAL Linear cu
5. et test Fan test display DMX adress value 1 512 B bit resolution 16 bit resolution Slow fade between values Fast snap between values OFF On adds 2 strobe channels Square dimmer curve Linear dimmer curve HIGH No fan speed limit LOW Fan speed limited Silent Action when loss of DMX signal HOLD last received DMX value OFF Sets output to zero MAN Go to Manual DMX value OFF 2n Display off after 2 minutes ON Display always on Shows software version READOUT ONLY Shows hardware version READOUT ONLY LED temperature READOUT ONLY 3 first digits shows DMX adress READOUT ONLY 3 last digits shows DMX value READOUT ONLY Confirm Reset unit by pressing enter Fan test First 2 digits set fan speed level 0 31 Last 3 digits RPS rounds per second READOUT ONLY Display test all seven segments of each digit on READOUT ONLY continues on next page WWW BROTHERS SONS DK LEDONARDO 1 USER MANUAL Software vers 1 3 00 SOFTWARE MENU continued Default values indicated by bold font Log Max Fan Maximum fan speed logged in RPS READOUT ONLY Fan RPS Current fan speed in RPS READOUT ONLY EEProm Developer info LED U LED voltage in Volts READOUT ONLY PSU U PSU voltage in Volts READOUT ONLY LED int for troubleshooting READOUT ONLY Log C Minimum and maximum logged temperature in C UP and DOWN scrolls min and max on time PSU on time in hours READOUT ONLY
6. ject to change without notice Go to www brothers sons dk for the latest version 4 WWW BROTHERS SONS DK user manual rev 1 06 LEDONARDO 1 USER MANUAL CONTENTS Safety Information Maintenance Product Overview Conversion 1 2 3 3 4 5 First Time Usage Installation rarrarararraraaravarrarerrarannareravanranevasrasranenasnasnsnerasrenesnen 10 AC PM ee 11 DMX Data Link 11 Software Update 11 DMX Protocol 12 Software Menu 13 15 Specifications WWW BROTHERS SONS DK LEDONARDO 1 USER MANUAL SAFETY Safety Notice It is important to read ALL safety information and instructions in this manual before install ing and operating the product described Safety symbol used in this manual A WARNING Potential injury or damage to persons or product A WARNING It is important to read ALL safety and installation instructions to avoid any damage to the product and potential injury to yourself and others This product is for professional use only and has been designed for indoor use Exposure to moisture may cause damage to the product and will void your warranty This fixture is designed for use with a specific LED only Use of any other type LED may be hazardous and may void warranty Do not operate the product if the ambient temperature exceeds 35 C 95 F Provide a minimum clearance of 0 1m 4 in around fans and air vents Do not mount on flammable surfaces Ensure that the fixture is elec
7. on LED LED on time in hours READOUT ONLY Demo Developer info DMX HZ DMX refresh rate READOUT ONLY DMX CH No of DMX ch transmitted by controller READOUT ONLY DMX br Break lenght of DMX in microseconds READOUT ONLY LED EE Developer info Manual 8 Manual intensity O 100 Intensity saved when pressing ENTER Display is always on in manual mode WWW BROTHERS SONS DK LEDONARDO 1 USER MANUAL SPECIFICATIONS Physical Depth 210 mm 8 27 additional depth when mounted O mm 0 Width 220 mm 8 66 additional width when mounted O mm 0 Height 260 mm 10 23 additional height when mounted 10 mm 0 39 Weight additional weight when mounted 1 5 kg 3 3 lbs Data DMX Channels 1 or 2 at Bbit 2 or 3 at 16bit Protocol USITT DMX512 A Electrical Never connect to dimmer power AG Power 100 240 V nominal 50 60 Hz Powersupply Electronic switchmode Max power consumption 132 W This fixture must be connected to ground Thermal Maximum ambient temperature t Amb 35 C 95 C Cooling t Case temperature as shown in display Below 64 C 147 2 F Convection cooled Above 64 C 147 2 F Forced silent fan cooling Above 70 C 158 F Forced dimming Above 73 C 163 4 F Forced Lamp Off Accessories Uploader BBS Software Uploader Specifications subject to change without notice For the latest specifications see www brothers sons dk WWW BROTHERS SONS DK 1
8. rve on Indicator Response fast indicator Strobe on Indicator 8 bit Indicator DMX present indicator SSSe ENTER UP DOWN MENU Open menu Go back ENTER Select Confirm UP Scrolling UP Increase value DOWN Scrolling DOWN Decrease value DMX Channels Mode Channel Parameter Value Percent Function 8 Bit 4 Dimmer O 255 O 100 Coarse dimming 8 Bit 1 Dimmer O 255 O 100 Coarse Dimming w Strobe 2 Strobe 0 5 O Open mode 6 125 1 49 Slow to Fast Strobe 126 130 50 Open 131 250 51 99 Slow to Fast Random 251 255 100 Open 3 Strobe O O 100 Short to Long Flash length 16 Bit 1 Dimmer O 255 O 100 Coarse dimming 2 Dimmer O 255 O 100 Fine dimming 16 Bit 1 Dimmer O 255 O 100 Coarse dimming w Strobe 2 Dimmer O 255 O 100 Fine dimming 3 Strobe 0 5 O Open mode 6 125 1 49 Slow to Fast Strobe 126 130 50 Open 131 250 51 99 Slow to Fast Random 251 255 100 Open 3 Strobe O O 100 Short to Long Flash length Note Beware when using Strobe Lenght that if the Strobe Lenght is egual to or longer than the flash and interval between flashes the unit will not strobe If maximum strobe length is used the fastest strobe possible will be 17 7 WWW BROTHERS SONS DK 1 LEDONARDO 1 USER MANUAL SOFTWARE MENU Software vers 1 3 00 Default values indicated by bold font Addr 1 Mode Resolution Response Strobe Curve Fan noDMX Display Tools Ver HW Ver Temp DMX In Res
9. ter clockwise Remove whatever you used to raise the LED assembly D When lowering the Main housing on to the Ledonardo make sure to fit the cabels rubber grommet into the notch on the side of the Main housing Mount Ledonardo on the main housing using eight Philips PH2 screws and eight serrated washers as shown Assuming you did as instructed the conversion is done Think of all the birds sitting in the tree top with a clear blue sky as the backdrop singing your praise for saving the environ ment so their kids can grow up in a safer world listen you can almost hear them singing what a wonderful world WWW BROTHERS SONS DK 9 user manual rev 1 06 LEDONARDO 1 USER MANUAL INSTALLATION A Do not operate the product if the ambient temperature exceeds 35 C Provide a minimum clearance of 0 1m 4 in around fans and air vents This fixture must be connected to ground This fixture is for indoor use only A Remove plastic protection from the LED before applying power Read the Safety and Specifications chapters first Applying power Never connect to dimmer power Install a power plug on the power cable using the following pin assigment 1 Neutral 2 Live Green Yellow Ground This fixture must be connected to ground Make sure the local power voltage is within the range specified If so connect the power cable and turn the power on Standalon
10. trically connected to ground earth Only use this product if all cables connectors and the product itself are undamaged Damage caused by inadequate cleaning or maintenance is not covered by the product war ranty This is a product using High power LEDs Do not stare directly into the LED at extended periods of time at a short distance without suitable protective eyewear Do not look directly at the LED with optical instruments that concentrate the light output No matter the light source blue light depending on the wavelength can be harmful to your eyes SERVICE Servicing is to be performed only by qualified personnel Take precautions to avoid ESD damage during service Disconnect the power before servicing the product MAINTENANCE This product requires very little routine maintenance if any but has special cleaning instructions Disconnect fixture from power and allow it to cool for 10 min Vacuum or gently blow away any dust from fan blades and grills Very gently clean the LED with Isopropyl alcohol Clean the lenses with a soft damp cloth POWER Never connect to dimmer power WWW BROTHERS SONS DK user manual rev 1 06 LEDONARDO 1 USER MANUAL PRODUCT OVERVIEW L 444 mm 17 48 294 mm 11 57 EE LED ONA
Download Pdf Manuals
Related Search