Manual - ACARD Technology Corp.
Contents
1. Connect to SATA HDD ARS 2050 Manual Chapter 3 Basic Instructions 3 1 Buttons and LCD There are four buttons and an LCD on the panel of ARS 2050 1 It shows a function or a message 2 It s used to scroll up function menus 3 It s used to scroll down function menus 4 Its used to execute a function 5 It s used to cancel a function 3 2 About HDD Installation HDD installation is not necessary but with a hard disk you can use the function of Image In other words you have one more choice to reproduce a DVD from an image file stored in the hard drive The following two subsections are about installing a 3 5 SATA hard drive and not installing respectively 3 2 1 With a HDD If you have installed a 3 5 SATA hard drive to your copy controller you need to operate according to the following procedures e Once your copy controller detects the hard disk it will ask you to choose a type to partition to format See function 12 4 Format HDD for more detail e Use function 8 Select Source to set the hard drive as the source e In function 9 Image select a partition to store the data e f there is no data in a selected partition place a source DVD into DVDROM and use function 9 01 Load to transmit data from DVD into the selected partition by pressing ENT Different data can be stored in different partitions e Switch to function 1 Copy by pressing A Place blank DVDs into DV2. Burn in Erase amp Copy Press ENT and use A to select the time of simulation such as 1 2 3 1000 or Run Continuous The figure below shows Run Continuous Sel burn in num Run Continuous 16 ARS 2050 Manual 5 1 7 Update Firmware Now press ESC and Y to enter the following figure Update Firmware is to update firmware to the latest version But you should get the firmware first 12 07 Adv Setup Update Firmware You can get the latest firmware version from ACARD by e mail or download it directly from the web site http www acard com Then unzip the file of zip and copy it into a CD RW If the file is bin you don t need to unzip After placing the media into the DVD ROM press ENT The system will begin searching the new firmware and show the message on LCD as follows after it finds the new firmware Then press ENT to update Searching F W XXX XXXX 5 1 8 Compare Firmware Now press ESC and Y to enter the following figure Compare Firmware is to compare the current firmware version and the newly downloaded version It can prove if the downloaded version is the newest one 12 08 Adv Setup Compare Firmware 5 1 9 H W Diagnostic Now press ESC and Y to enter the following figure H W Diagnostic is to test the system 12 09 Adv Setup H W Diagnostic Press ENT to enter the next figure and begin the LCD test After that the system wil
3. Motherboard System model SCSI host adapter chip brand amp model SCSI host BIOS version Other VO card Operating System SATA HDD brand 8 model SATA HDD capacity SATA HDD firmware Problem description 26
4. after copying Press a Key to Eject Good Disc Press any ket to eject the good disc after copying Read disc error eds During comparison the disc cannot be read Save new config Fall cece The new setting of configuration cannot be saved Source Disc EMmplyH oooonssait aan The source disc doesn t contain any data Source Disc Not Read Source disc is not ready to be read Source Drive Not Read Source drive is not ready to read Src amp Tgt can t in the same channel nn ncnnnnnnnnnnnnnnn non nncnnnnncnnnnnns E During comparison the source and target discs cannot be in the same channel Target Disc Not Empty nono nnnnnnnnnnno The target disc still has data Target Disc Not Read Target disc is not ready to be written into Target Drive Not Ready 0ccccocioescisssosio anoto Target drive is not ready to write Target overflow The target disc hasn t enough capacity to store new data TOG not Match cuina The comparison results are not the same User Aborti aininn en E Cancel the job during operation 2 Connecting with a HDD All data will be lost EE Ee ais ee All data on the hard disk will be lost Confirm the formatting of hard disk Delete Image in Partition xd Confirm the deleting of data image in partition xx Format HDD cita E Ask if you want to format the hard disk Format HDD OKT The Formatting of hard disk has been completed HDD not Forimatlh 2 2 cs2cssoccecc cecesassacssceesacce
5. or a DVD writer cannot read confirm the format of the source DVD and check if it is damaged Use any DVD writer to read the source DVD If it works the DVD ROM is probably defective or not compatible with the source DVD 6 4 About Buttons If you press any one of the four buttons on the panel but there is no response it is perhaps that the button cannot function well Inspect the jumper setting 6 5 About DVD Writer Not Readable After copying if the DVD writer is not readable use Compare to examine or get another DVD ROM to test 6 6 About High Failure Rate If the failure rate of copying is high do the following things to improve e Lower the speed of DVD writer e Inspect if the blank disc s quality is good e Update the firmware e Inspect the DVD writer s maximum writing speed If the speed is over 8X copy the data to a hard disk first and then transmit to DVD 6 7 About Firmware Update If you cannot update the firmware please inspect the firmware Perhaps you have downloaded a wrong file Failure in firmware update may cause the copy controller to fail in booting Under the circumstances return the control board to distributor for repair 6 8 About Function 12 and Cancellation If you want to execute function 12 Advanced Setup you can press ESC for 2 seconds And during operation if you want to cancel a function like Copy Test Verify and so on you can press ESC for 2 seconds too 23 ARS 2050 Manu
6. ARS 2050 Native SATA Copy Controller User s Manual Version 1 1 for PCB Rev 4 x Attention Wait over 5 seconds to power on after shutdown to prevent the abnormal operation of the system ACARD FEGARNOLCOGY Copyright 2009 ACARD Technology Corp Release October 2009 CE FE Copyright and Trademarks The information of the products in this manual is subject to change without prior notice and does not represent a commitment on the part of the vendor who assumes no liability or responsibility for any errors that appear in this manual ACARD and SCSIDE are the trademarks of ACARD Technology Corp This manual contains materials protected under International Copyright Laws All rights reserved No part of this manual may be reproduced transmitted or transcribed without the expressed written permission of the manufacturer and author of this manual ACARD s ARS 2050 Copy Controller is used for copying and editing personal audio and video data Violating Copy Right is a criminal act ACARD s Copy Controller only supports legal backup operation ACARD Technology Corp is not responsible for illegal recording Table of Contents Chapter Retro et LEE oda 6 et e EE 6 A 6 er tee 6 1 4 System Requirement ooonccnccccncccnccccnncnnnnononcnnnnnnoncnnnnnnnnnons 6 Chapter 2 Hardware Installation nnnnnn00nnnnnnnnneannnnnnnnnennnnnnnn 7 2 1 Copy Controller Only acia ti at 7 2 2 A Whole EC 7 2 3 A Sys
7. D writers and press ENT to start copying e When copying comes to an end the passed DVDs will eject automatically The default is ejecting automatically but you can change it e The failed DVDs will remain in the writers The default is keeping failed DVDs in the writers but you can change it To take the failed DVDs you need to press the eject buttons on the writers e During operation do not press any button on your copy controller because interruption will harm the device and DVDs will be damaged too ARS 2050 Manual 3 2 2 Without a HDD If you haven t installed a 3 5 SATA hard drive to your copy controller you need to operate according to the following procedures e Place a source DVD into DVD ROM e Switch to function 1 Copy by pressing A Place blank DVDs into DVD writers and press ENT to start copying e When copying comes to an end the passed DVDs will eject automatically The default is ejecting automatically but you can change it e The failed DVDs will remain in the writers The default is keeping failed DVDs in the writers but you can change it To take the failed DVDs you need to press the eject buttons on the writers Before installing the hardware please check that the data cables are correct SATA Cable Connects the SATA HDD SATA writer directly with the SATA port on the ARS 2050 board via a direct SATA connection S SE 4 NS lt i Y A Connects to SATA port on ARS 2050 Connects
8. O ACARD o6ba3aH ObITb OTBETCTBEHHbIM 3a TO YTO NepepaboTtan Bce NpoAYKTbI 3KCNOPTNpyeMbIe B FepmaHuto Bol MOKETe BO3BPaTHTb Bal NpoAyKT ACARD kOTOpbIM HyYKAAETCA B peunpkynauna MeCTHOMY COOpLuNKy WEEE Statement Afin de g rer la quantit croissante de d chets lectriques et lectroniques de r duire l utilisation des d charges et des incin rateurs et d viter que des d chets nocifs ne polluent l environnement l Union Europ enne a publi la directive WEEE sur les d chets lectriques et lectroniques Celle ci sp cifie que les fabricants doivent collecter recycler et traiter l quipement lectronique et lectrique usag Depuis le 13 aout 2005 les pays membres ont mis en place un systeme de recyclage gratuit selon le WEEE De ce fait Acard est responsable du recyclage de tous les produits export s vers Allemagne Vous pouvez mettre au rebut votre equipement ACARD usag dans votre centre local de recyclage Pour plus d informations sur les lieux de mise au rebut des quipements usag s destin s au recyclage veuillez contacter votre mairie votre service de traitement des d chets m nagers ou le magasin ou vous avez achet le produit RAEE Spanish Con la finalidad de reducir el incremento de residuos el ctricos y de material electr nico reduciendo el uso de los vertederos e incineradoras y prevenir el preocupante aumento del contacto de estos residuos con el medio ambiente Por este motivo la Uni n Euro
9. al Appendix A LCD Messages 1 Normal Conditions All data will be lost erase All data on the disc will be lost Confirm the erasing of data PRT VAY ZING ec ee eg Analyze the source disc Audio Disc Cantcomparel The system cannot compare the audio discs Cannot read TOG cloacas note The system cannot read the contents of disc Check Target Please Wait oooooooooccconnccccccccccccccccccno The system is checking the target device Detect Drive ccc cic cnn cren nen Detect what drives are connected with the system DVD RW does not Support the Func DVD RW doesn t support this function Erase FIniSMe G ie ico The erasing of data comes to an end Erasing RE The system is erasing the data on the disc Fail to get Drive Info oooooooocccooocccocccccocccccccccccnannnnn nos The drive information cannot be obtained Fail to get Src Discintol The information of source disc cannot be obtained Hold ESC to BM cta aan Press ESC for a second to terminate the test nger eege EE e The comparison results are the same Initialize SDRAM ne Rt Initialize the memory of the system Load Default Conftg ressens Do you want to load the default settings No Erasable DiscmDND PWIL The disc on the DVD RW device is not rewritable Preparing eocena aana aiaa adaa a ee eee eee The system is preparing to record Press a Key to Eject Fail Disc Press any key to eject the failed disc
10. at HDD is to partition the hard disk But after formatting all data on the hard disk will be deleted 12 04 Adv Setup Format HDD If your copy controller doesn t connect with a hard disk LCD will show the message as follows No Valid HDD Select HDD First If your copy controller is connect with a hard disk LCD will ask you to choose partition type There are 5 types of partition size for you to choose which are F_S DVD CD DL and Auto HD Partition Size Select DVD Press ENT to enter the following figure All data on the hard drive will be lost after the format and you are asked to confirm again The default is No Press W to select Yes All data will be Lost format No After the hard drive is formatted correctly LCD will show the message as follow Press ENT to verify HDD or press W and choose No to finish Format HDD Format HDD ok verify HDD Yes How do choose HD partition type In DVD a partition occupies 5GB in CD 1GB in DL 10GB and in Auto 1GB When hard drive is partitioned as F_S DVD CD or DL you are not allowed to load images larger than the partition size Ex If you choose to partition as DVD you are only allowed to load DVD and CD images but not DL When hard drive is partitioned as Auto controller will automatically occupy partitions for your image type Ex If you choose to partition as Auto controller will occupy 1 partition and 5 partitio
11. cgunsensauasceetndy The hard disk hasn t been formatted yet HDD too small aaee aae ae ds The capacity of hard disk is too small HDD too small to handle mmagel nn nccnnn EEN The hard disk hasn t enough capacity to store the data image at least 5Gbytes Image Exists Ovenwrte AA E There is a data image in the current partition Confirm the overwriting of data 24 ARS 2050 Manual Image load Fail The image isn t successfully loaded from DVD to the hard disk Image load Ok The image is successfully loaded from DVD to the hard disk No Image in Partition xx There is no data image in partition xx No Valid HDD La O O O The system cannot find a hard disk Partition Damage suicidar oe eee Peed The partition is damaged Select HD KAES gemeeten EE Select a formatted hard disk at first Verify Disk or Partition Do you want to verify the hard disk or just a partition Verify Hard Disk Fall The hard disk is not verified successfully 3 Audio Editing Burn or Move to Parton Segen tae cress tree deed dereen dE A cede nena telat Do you want to directly copy the data into disc or move them to the partition Can t edit HDD The hard disk cannot be edited as a source audio disc Close all dieceeession conocio Confirm the closing of disc sessions Continue edit next Disch Ask if you want to continue the music disc editing End edit disc and bum eee Finish the music disc editin
12. chtlinie ber Elektro und Elektronik Altger te erlassen Die Richtlinie verpflichtet Hersteller elektrische und elektronische Altger te umweltgerecht einzusammeln zu recyceln und zu entsorgen Die Mitgliedsstaaten der EU haben bereits ihre kostenfreien Recyclesysteme konform der WEEE vor dem 13 August 2005 eingerichtet Entsprechend der Richtlinie ist ACARD verantwortlich f r die umweltgerechte Entsorgung aller nach Deutschland exportierten ACARD Produkte Sie k nnen Ihr zu entsorgendes ACARD Produkt zu Ihrer rtlichen Sammelstelle bringen AEEA verklaring Met het doel de stijgende hoeveelheid afgedankte elektrische en elektronische apparatuur te beheersen zonder hiervoor onnodig stortplaatsen en verbrandingsovens te belasten en om de vervuiling van het milieu door vrijkomende stoffen uit de afgedankte apparatuur te voorkomen heeft de Europese Unie EU de richtlijn betreffende afgedankte elektrische en elektronische apparatuur besloten Deze richtlijn verplicht fabrikanten afgedankte elektrische en elektronische apparatuur in te zamelen te recyclen en te verwijderen De lidstaten van de EU hebben reeds de kosteloze recyclesystemen volgens de AEEA v r de 13 augustus 2005 ingericht Conform de richtlijn is ACARD verantwoordelijk voor de verwijdering van alle naar Nederland ge xporteerde ACARD producten U kunt uw afgedankt ACARD product naar uw locale inzamelplaats brengen Elektrik ve Elektronik Madde At klar Demeci Elektrik ve electro
13. dable oococccccccnnoccccccccccnnccccccno 23 6 6 About High Failure Rate cccccccoccccnccccoccnnccnnancnncononccononnnos 23 6 7 About Firmware Update occccconcccocononcconconocononconanonononons 23 6 8 About Function 12 and Cancellation ccccccnn 23 Appendix A LCD Messages coocccccccnocconcccnoncnnnnonancnnnnonancnnnonnnanoss 24 Technical Support ld EEN 26 TECHNOLOGY ACARD WEEE Statement H O D EE WEEE Statement English In order to cope with the increasing waste electrical and electronic equipment reduce the use of landfill and incinerator and prevent the harmful matter of waste equipment from entering the environment the European Union EU has set the Directive on Waste Electrical and Electronic Equipment WEEE asking manufacturers to collect recycle and treat waste electrical and electronic equipment properly Member nations already established their free of charge recycle systems of WEEE before August 13 2005 Accordingly ACARD has to be responsible for recycling all products exported to Germany You can return your ACARD product that needs recycling to a local collector WEEE Erkl rung Mit dem Ziel die steigende Menge elektrischer und elektronischer Altger te zu bew ltigen ohne hierzu unn tig M lldeponien und Verbrennungsanlagen zu belasten und um die Verschmutzung der Umwelt durch freiwerdende Stoffe aus den Altger ten zu vermeiden hat die Europ ische Union EU die Ri
14. e controller supporting high speed SATA DVD CD writers With ACARD RISC CPU Engine it doesn t need connecting to a computer or require much learning Simply through the LCD and the button on the panel you can use the copy controller to back up data audio or video DVD CD quickly It support SATA DVD drives for recording DVD CD quickly It is fit for companies desire to do a small amount of production without efforts 1 2 Features A standalone SATA to SATA DVD CD duplicate controller m Independent fully native SATA channel data acceleration m Totally independent without installing hardware or software m Supports a built in 3 5 or 2 5 SATA hard disk drive m Supports 12X SATA DVD recording m Has a user friendly interface and shows messages with LCD Firmware update by DVD ROM 1 3 Specifications m ACARD SATA Controller ACARD 32 bit RISC CPU 16Kbyte data cache inside the RISC CPU m High reliability of SDRAM for embedded system m 12 SATA interface channel m 2 x 16 LCD screen m A membrane 4 buttons operation panel m 512KB flash memory for copy code m Dimension D 215mm W 150mm H 42mm m Power Source DC 5V 1 4 Systme Requirement m Upright external case 12 13 x 5 25 m Power supply of 300W SATA cable m Digital DVD ROM x 1 Digital DVD writer x 10 for each tower SATA hard disk drive optional m Tray optional ARS 2050 Manual Chapter 2 Hardware Installation Before installing ARS 2050 notice
15. ed with a PC 12 13 Adv Setup USB Option Press ENT to enter the next figure The default is Off Press W to select On USB Option Off When USB option is On the original 12 Adv Setup will change to 13 Adv Setup and the hidden 12 USB Mode will appear in the first layer of function menu USB L H Mode 18 ARS 2050 Manual 5 1 14 CD TEXT Now press ESC and Y to enter the following figure CD TEXT is a kind of special copying format This function supports this special format 12 14 Adv Setup CD TEXT Press ENT to enter the next figure The default is Off Press W to select On CD TEXT Off 5 1 15 Password Now press ESC and Y to enter the following figure Password is set to protect your copy controller 12 15 Adv Setup Password Press ENT to see the following figure The default is Off Password Off Press to see the following figure Change means to change a default or an old password into a new one Password Change Press to see the following figure Old Password Use A to key in the default 85122290 A password should be composed of 1 to 13 characters The character can be A B C etc or 1 2 3 etc or the combination of both After selecting a desired number or alphabet remember to press ENT Old Password 8 After keying in the old password remembe
16. g and start to copy Erase selected Tracks Abort the selected tracks and delete them Ins empty disc Continue Do you want to insert a blank disc and continue copying Insert HEES ege ee ee ee Insert the next audio disc NO AUDIO track in this dier The source disc has no audio track Sessions were closed already The disc sessions have already been closed Target Overniow Re Select citar li A A adds pda de The disc capacity is not enough to store the selected tracks Please select again Tgt overflow del last Egeter a ee EE The disc capacity is not enough to store the selected tracks So do you want to delete the last track 4 Firmware Update Check Sum ERROR Lia lisa The udpated firmware has errors Flash ROM tal Data cannot be written into Flash ROM Invalid firmware 0 ccccccceeeeeeeeeeeeeeeeeeeetteeeeeeees The disc doesn t contain a valid firmware Last update F W Fal cece ceceeee cece eeeeteeeeeeeeeeeees The firmware is not updated successfully Last update F W ORT The firmware is updated successfully Searching FW ccoo The system is searching for a valid firmware Source can t be Hard Disk During comparison the source cannot be hard disk 25 ARS 2050 Manual Technical Support Form Email address support acard com Website http www acard com Model Name ARS 2050 Firmware version System Configuration
17. l do the button test self test of SDRAM the hardware connection test and flash test All test results will be shown on LCD It is the easiest way to know if the system can work well LCD Test Start When all tests finishes LCD will show the message as follows Test finished 5 1 10 Load Default Now press ESC and Y to enter the following figure Load Default is to make all changed settings return to defaults 12 10 Adv Setup Load Default 17 ARS 2050 Manual Press ENT to enter the next figure Use A W to confirm Yes or No Load Default Config Yes When default loading finishes LCD will show the results as follows Load Default OK 5 1 11 CD G Now press ESC and Y to enter the following figure CD G is a kind of special copying format This function supports this special format 12 11 Adv Setup CD G Press ENT to enter the next figure The default is Off Press W to select On CD G Off 5 1 12 ISRC amp MCN Now press ESC and Y to enter the following figure ISRC and MCN are special copying formats This function supports them 12 12 Adv Setup ISRC amp MCN Press ENT to enter the next figure The default is Off Press W to select On ISRC amp MCN Off 5 1 13 USB Option Now press ESC and Y to enter the following figure USB Option lets you switch to the USB mode if your copy controller has connect
18. me Refer to page 17 for the menu Under the first layer on function menu press ESC for 2 seconds to enter Function 12 01 as the following figure shows 12 Adv Setup 5 1 1 UnderRun Protect UnderRun Protect lets you control On and Off of Buffer Under Run Protection 12 01 Adv Setup UnderRun Protect Press ENT to enter the following figure UnderRun Protect lets you control On and Off of Buffer Under Run Protection The default is On Press W to select Off UnderRun Protect On 5 1 2 Overburn Now press ESC and Y to enter the following figure Overburn lets you decide whether to copy beyond the limit of the media or not 12 02 Adv Setup Overburn Press ENT to enter the following figure The default is Off Press W to select On Overburn may cause a DVD writer to be damaged and data incomplete Overburn Off 5 1 3 Read Error Skip Now press ESC and Y to enter the following figure Read Error Skip is to ignore any error that occurs during copying Under normal circumstances when an error occurs during copying a message will appear on LCD Yet you can use Read Error Skip to copy some defective medias 12 03 Adv Setup Read Error Skip 14 ARS 2050 Manual Press ENT to enter the following figure The default is Off Press W to select On Read Error Skip Off 5 1 4 Format HDD Now press ESC and Y to enter the following figure Form
19. nik madde at klar n n yukselmesiyle basedebilmek arazi doldurma ve cop yakma f r n kullan m n azaltmak atik madde zararlar n n cevreye yay lmas n onlemek icin Avrupa Birligi AB ureticilerden elektrik ve elektronik madde at klar n gerektigi gibi toplamalar n geri donusturmelerini ve kimyasal isleme tabi tutmalar n talep etmek icin Elektrik ve Elektronik Madde At klar uzerine bir direktif haz rlad Topluluk uyeleri 13 Agustos 2005 ten once elektrik ve elektronik madde at klar n n ucretsiz geri donusum sistemlerini coktan olusturmuslard Bundan dolay ACARD Almanya ya ihrac ettigi butun urunlerin geri donusumunden sorumludur ACARD urunleri geri donusum gerektirirse yerel toplay c lara geri verebilirsiniz WEEE GtoneTeHb UTO6bl cllpaBUTbCA C YBENUYUBaIOLUMMCA HEHYKHbIM INEKTPUYECKUM N INTEKTPOHHbIM o6opyAoBaHuem YMeHBLUUTE UCNONb3OBaHUNe 3akKanbIBAHNA Mycopa n NCNONb3OBAHNA YCTAHOBKU Ana CKUTaHusa OTXOACB MPenaTcTByUTe BpeaHomy BbIOpocaM 3arpa3gHaTb OKpykaHOBKU Cpeny EBpone cku coto3 EC ycranoBun AupekTuBy no HeHykHoMy OnekTpnyeckomy n InekTpoHHoMy O6opyaocBaHuto WEEE ana Toro 4TOGbI U3roTOBUTene coOpann nepepabaTbiBanm n BOOLE MpOABUNM BHNMAHNE K HOHYKHOMy INEKTPUYHECKOMY N 3J1IEKTPOHHOMY o6opyAoBaHut GOMKHbIM OOpa3om Une Haunn ycTaHoBunu GecnnaTHyto CUCTEOMY n 3NeKTPOHHOMy ODOPyAOBAHUH AOJDKHBIM OOpazom UnieHbl Hann ycTaHoBunn GecnnaTHyio cuctemy nepepaborku WEEE go 13 asrycta 2005 CootBeTcTBeHH
20. ns when CD and DVD images are loaded respectivelly Therefore Auto is the most efficient way to load images of different type Partition Type Partition Size Images to load 15 ARS 2050 Manual 5 1 5 Verify HDD Now press ESC to return to Function 12 and then select part 5 Verify HDD as the following figure shows Verify HDD is to verify if the hard disk or any of its partitions can work well 12 05 Adv Setup Verify HDD Press ENT to enter the next figure Use A W to confirm Disk or Parti Verify Disk or Paration Disk Press ENT to verify After verification LCD will show the results as follows Verify HDD OK 5 1 6 Burn in Now press ESC and Y to enter the following figure Burn in is to simulate the copying progress many times The time can be from 1 to 1000 After each cycle of simulation the medias on the DVD writers will eject automatically and recede for the next bout of simulation 12 06 Adv Setup Burn in Press ENT to enter the next figure Test is simply a simulation Burn in Test Press ENT and use A Y to select the time of simulation such as 1 2 3 1000 or Run Continuous The figure below shows Run Continuous Sel burn in num Run Continuous Press ESC ENT to select Erase amp Copy as the following figure shows Erase amp Copy is to erase and write repeatedly It is only for media rewriteable discs
21. ob Then press ENT to return to the next figure Disc Counter View 20 ARS 2050 Manual Press to see the following figure It is to delete the record in job Use A W to confirm Yes or No Disc Counter Del Job Counter Press Y again to enter the following figure Dev means the device of DVD writer Disc Counter Del Dev Counter Press ENT to see the following figure If you want to delete the record in DVD writer 2 you can press ENT otherwise press ESC to exit Del 02 Counter Ent Del Esc Exit 5 1 17 Auto Save Image Now press ESC and Y to enter the following figure Auto Save Image can save an image file automatically into your designated partition of HDD 12 17 Adv Setup Auto Save Image Press ENT to enter the next figure The default is Off Press W to select On Auto Save Image Off 5 1 18 Update Drive F W Now press ESC and Y to enter the following figure Only when you have installed some types of CDIDVD drives produced by ASUS or Plextor can this figure appear This function lets you udpate the firmware of some ASUS or Plextor CDIDVD drives For the detailed types visit the Web site www acard com 12 18 Adv Setup Update Drive F W Press ENT to enter the next figure No F W File means that there is no file of firmware on the source reader So in the beginning you have to download the firmware of a certain type of CD DVD dri
22. pea ha fijado la Directiva de Residuos de Aparatos El ctricos y Electr nicos RAEE solicitando a los fabricantes la recolecci n reciclaje y tratamiento de ests residuos correctamente Los paises miembros ya han establecido su sistema de reciclaje gratuito de RAEE antes del 13 de Agosto del 2005 Por este motivo ACARD es el responsable del reciclaje de todos los productos exportados a Alemania Usted puede devolver su producto Acard a un punto de recogida local cuando desee reciclarlo Dichiarazione WEEE Per far fronte all aumento dei residui delle apparecchiature elettriche ed elettroniche ridurre l uso di materiale di riporto e degli inceneritori ed impedire che il materiale nocivo delle apparecchiature residue entri a contatto con l ambiente Unione Europea UE ha stabilito le Direttive sui Residui delle apparecchiature Elettriche ed Elettroniche WEEE chiedendo ai fornitori di raccogliere correttamente riciclare e trattare le apparecchiature elettriche ed elettroniche residue Le nazioni facenti parte dell Unione Europea hanno gi stabilito il loro sistema gratuito di riciclaggio di questo materiale WEEE prima del 13 agosto 2005 Di conseguenza ACARD responsabile del riciclaggio di tutti i prodotti esportati in Germania Potete restituire il vostro prodotto acquistato da ACARD che deve essere riciclato da un azienda specifica locale ARS 2050 Manual Chapter 1 Introduction 1 1 Overview ARS 2050 is a standalone duplicat
23. r to press ENT to confirm Then the following figure will appear New Password 9 19 ARS 2050 Manual Follow the rule mentioned above to key in a new password After keying in the system will ask you to enter the new password again Re Ent Password 2 When it is correct you will see the following figure You have 3 chances to enter your password If you forget your password return the copy controller to ACARD for help Change OK 5 1 16 Disc Counter Now press ESC and Y to enter the following figure Disc Counter records how many discs you have copied 12 16 Adv Setup Disc Counter Press ENT to see the following figure View means to see the records Disc Counter View Press ENT JC in the following figure means Job Counter that is every copying task It records the number of discs you have copied and can be deleted JC OK 000000001 Fail 000000000 Attention There is another record of LC Life Counter It also records the number of discs you have copied so far but cannnot be deleted You can veiw the record of LC by holding down ESC when LCD shows the finding of writers Press A to leave Press W The following figure shows the record in DVD writer 2 You can press W to see the records in other writers This kind of record can be deleted too 02 OK 000000001 Fail 000000000 Press A to return to the record of j
24. tem without DVD Drives aaoannnnnnnnonnnnnnnnnnnnnnennennennnne 7 2 4 Installation Instructions oooncccoconnnoconcnnonononconanonononcnnnnos 8 2 4 1 Installing the ARS 2050 0occcccccocccncccconccnncononcnnnnonanonnnnos 8 Chapter 3 Basic Instructions nnnnnnnnneannnnnnnnnennnnnnnnsnnnnnnnennnne 9 3 BHON and LOD andas 9 3 2 ADOUL HDD Installation canica 9 ER un Ee IT RE 9 3 2 2 Without a E RRE 10 Chapter 4 PC Bim Ayoun assi 11 Chapter o FUNCION asi 12 STAV SGUD Eege 14 En a Wale Ee ie Net 14 E Ee et d WEEN 14 q A tanceetaelud a ATRE 14 Oo EA OMe A Bae oo oca 15 Be E FID EE 16 EE WEE 16 5 1 7 Update Firmware ooccccccccocccncccnoncnnnocnonnnnnnonancnnnnnnanennnnos 17 5 1 8 Compare Firmware occccncccccccnnccnnncccnnnonncnnnncnonnnannnnnnnnnos 17 5 1 9 FW RI Le ue LEE 17 5 1 10 Load Default 2espgigedesdekebi senge Geh ESS eeh AS ee 17 e E DE E 18 51 12 IS RG ee MCN id 18 e KE e al EE 18 A A 19 A EE 19 5 1216 DISC COUNTER ee 20 5 1 17 Auto Save IMAGE cccccccccccconcccnnncconononononnnonononanononnnnnns 21 51 18 Updat Drive F W siii ib 21 A eege eebe eeheeeeaeech 21 3 20 AUTO MUR TIME aaoi 22 Chapter 6 Troubleshooting snon0annnnnennonnnnnnnnnnnnnnnnnnnnennnnnnnn 23 6 1 ADQUE LEDs oil 23 6 2 About Error Messages oocccccoococococcoconononccnnnononnncnnonanoncnnos 23 6 3 About DVD ROM 8 DVD Writers occcccccccncccccccccccccocnnnnos 23 AA DOS oda 23 6 5 About DVD Writer Not Rea
25. that there are three kinds of packages the copy controller only a whole copying system and a system without DVD drives 2 1 Copy Controller Only m Unpack the package and examine if there is any defect or malfunction Prepare a DVD ROM Prepare DVD writers Prepare a 3 5 hard drive optional 2 2 A Whole System m Unpack the package and examine if there is any defect or malfunction Prepare a 3 5 hard drive optional Be sure that the watt of power supply is sufficient 2 3 ASystem without DVD Drives m Unpack the package and examine if there is any defect or malfunction Prepare a DVD ROM Prepare DVD writers Prepare a 3 5 hard drive optional Be sure that the watt of power supply is sufficient ARS 2050 Manual 2 4 Installation Instructions 2 4 1 Installing the ARS 2050 The following diagram shows how the ARS 2050 is connected to 1 DVD ROM 1 SATA HDD and 10 DVD writers in Stand Alone mode O Sa SATA HDD DVD ROM DVD Writer DVD Writer E DVD Writer DVD Writer SE LCD ARS 2050 DVD Writer a DVD Writer DVD Writer DVD Writer DVD Writer a DVD Writer Connect to Target DVD Writers Large 4 pin power supply Connect to Target DVD Writers d i Connect to Source DVD ROM
26. to SATA HDD SATA Writer s SATA port 10 ARS 2050 Manual Chapter 4 PCB Layout The board layout of ARS 2050 is shown as follows A O CN10 CN11 J3 USB signal control CN5 upper level Connects to source DVD ROM CNS bottom level Connects to SATA HDD CN3 amp CN4 amp CN6 amp CN7 amp CN10 amp CN11 Connects to target DVD writers CN9 Power socket 11 ARS 2050 Manual Chapter 5 Functions There are 12 major functions in the copy controller as the following figure shows and there are subfunctions in Function 9 10 11 and 12 12 Advanced Setup is a hidden menu Press ESC for 2 seconds to enter this function There is another hidden function USB Mode which will only show up when you enable USB Option under Advanced Setup 12 ARS 2050 Manual In Function 12 there are 20 subfunctions This is a special function See P 18 for details 13 ARS 2050 Manual During operation if you don t understand an LCD message see Appendix A Now let s take ARS 2050 to demonstrate 5 1 Adv Setup Function 12 Adv Setup lets you change the system configuration This function includes 20 subfunctions UnderRun Protect Overburn Read Error Skip Format HDD Verify HDD Burn in Update Firmware Compare Firmware H W Diagnostic Load Default CD G ISRC amp MCN USB Option CD TEXT Password Disc Counter Auto Save Image Update Drive F W Index and AutoRun Ti
27. ve from the Web site of ASUS or Plextor Then record the firmware into a CD RW No F W File 5 1 19 Index Optional Function Now press ESC and Y to enter the following figure Index is a kind of special copying format This function supports this special format 12 19 Adv Setup Index 21 ARS 2050 Manual Press ENT to see the following figure The default is Off Index Off 5 1 20 AutoRun Time Optional Function Now press ESC and Y to enter the following figure AutoRun Time can a copy automatically within few seconds 12 20 Adv Setup AutoRun Time Press ENT The default is 5 second AutoRun Time 5 Press W could select as off or 1 99 second Press ENT to confirm the selection 22 ARS 2050 Manual Chapter 6 Troubleshooting 6 1 About LCD After you power up if there is no display on the LCD check if the connection of power cord is firm and the environment of power outlet is normal 6 2 About Error Messages During Copy Test Compare and Verify etc if you press ESC to abort an error message will appear on LCD Abortion may cause the copy controller to hang up therefore you have to power on again If reading fails an error message will appear on LCD Get a new source DVD to try again If the copy controller hasn t detected any device after powering on an error message will appear on LCD 6 3 About DVD ROM DVD Writers If a DVD ROM
Download Pdf Manuals
Related Search