Manual - Microh
Contents
1. Any non manufacturer additions modifications or changes in any way will void the warranty Please do not attempt to open unit It is only to be serviced by an authorized technician If this occurs or is apparent the warranty will be voided The fixture s warranty will be voided if there are any malfunctions from not following the user manual or any illegal operation shock short circuit electronic shock lamp broke etc This unit has a total of 6 operating modes Master Slave DMX Manual Strobe Colour Fade amp Colour Change MASTER SLAVE MODE By connecting the 3 pin DMX you can daisy chain up to 30 units on master slave mode Daisy chain the fixtures together by plugging from the DMX output of the first fixture into the DMX input of the second fixture and so on On the master fixture set to one of these modes colour fade colour change strobe or manual mode On the slave fixtures set the unit to DMX mode DMX MODE Press and release the A button until 001 is displayed Press the B button to edit Use the A amp B buttons to select desired address Example Current address is 001 and it is desire to change to address 125 Press the A button to find 0 01 to select B and press the B button to change to 1 Press the A button to change the next digit 10 1 press the B button press 3 times to change to 2 Press the A button to select the last digit and press the B button 5 times to change to 5 Led Chameleo2. minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture Whether installing inverted on a truss or ceiling or set on a flat level surface Be sure this fixture is kept at least 0 5m 1 5 ft away from any flammable materials decoration etc Always use and install a safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails Mounting Points Overhead mounting requires extensive experience including calculating working load limits A knowledge of the installation material being used and periodic safety inspection of all installation material and the fixture are all imperative and should only be performed by a qualified technician Improper installation can result in bodily injury and damage Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Clamp Mounting The MICROH LED CHAMELEON V2 provides a unique mounting bracket assembly to mount on a truss or the floor When mounting this fixture to truss be sure to secure an appropriately rated clamp Be sure to attach the clamp to the bracket through the center hole As an added safety measure be sure to attach at least one properly rated safety cable to the fixture Regardless of
3. the rigging option you choose for your MICROH LED CHAMELEON V2 wash fixture always be sure to secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle 5 DMK 512 CONTROL CONNECTIONS This fixture complies with international USITT DMX standards and can be used with either a 3 pin DMX connector or a 5 pin DMK connector Plug in the provided 3 pin XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the LED CHAMELEON V2 To connect the units to DMX you must daisy chain the fixtures together as referred in the diagram below Always end your DMX 512 connection with a DMX terminator DMX OUTPUT CONTROLLER FIXTURE 1 FIXTURE 2 FIXTURE 3 mener XTN DMX OU X X X X UPTO 30 UNITSIN s MASTER SLAVE MODE a o DOHyH LET LES ET VA NA Aa sls 4 Sitaat XLR CABLE XLR CABLE XLR CABLE DMX Output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket COMMON Ym MOT owen DMX 3 PIN XLR 1 Ground DMX512 OUT 2 Data 3 bE 3 PIN XLR For installations where the DMX cable has to run a long distance or is in an electrically noisy environment it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise
4. 00 009 No Function 010 057 Strobe Slow to Fast 058 059 No Function 060 108 Strobe Slow to Fast 109 110 No Function 111 159 Strobe Fast 160 161 No Function 162 255 Random Strobe Channel 6 MACROS 000 009 No Macro 010 050 Colour Fade 051 091 Colour Fade RGB Only 092 132 Colour Fade 133 173 Colour Snap 174 214 Colour Pulse 215 255 Random all Macros 8 KEY FEATURES 36 x 1W LEDs 12 Red 12 Green 12 Blue 6 Operation Modes 3 Pin XLR Input amp Output DMX Control with 3 DMX Modes 3 4 or 6 Channel Bracket for Truss and Floor Mounting 2 Button LED Digital Display A B IP65 Rated for Outdoor Use Flicker Free 9 TECHNICAL SPECIFICATIONS MODEL LED CHAMELEON V2 LAMP 36 x 1W Tri LEDs OPERATING TEMPERATURE 25 C to 45 C VOLTAGE 120VAC 60Hz 60W FUSE 1A 250V IP RATING IP65 DIMENSIONS 12 6 x 5 7 x 8 9 320 x 145 x 226 mm PACKING DIMENSIONS 15 55 x 9 65 x 7 68 395 x 245 x 195 mm NET WEIGHT 8 65 Ibs 3 92 kg GROSS WEIGHT 9 75 Ibs 4 42 kg WARRANTY 2 Year Limited Warranty 10 MAINTENANCE AND CLEANING The following points have to be considered during the inspection 1 All screws for installing the device or parts of the device must be tightly connected and must not be corroded 2 There must not be any deformations to the housing or installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate wi
5. IVIICROKF PROFESSIONAL PRODUCTS www micronpro com USER MANUAL LED CHAMELEON V2 Keep this manual for future reference TABLE OF CONTENTS 1 INTRODUCTION AND UNPACKING 1 2 SAFTEY INSTRUCTIONS 1 2 3 OPERATION INSTRUCTIONS 2 3 4 MOUNTING AND INSTALLATION 4 5 DMK 512 CONTROL CONNECTIONS 5 6 MENU NAVIGATION 6 7 7 DMX CHANNELS 8 8 KEY FEATURES 9 9 TECHNICAL SPECIFICATIONS 9 10 MAINTENANCE AND CLEANING 10 1 INTRODUCTION AND UNPACKING Thank you for purchasing the MICROH LED CHAMELEON V2 wash fixture For your own safety and knowledge please read this manual before installing or operating the device This manual covers the important information on installation and applications Please install and operate the fixture according to instructions Meanwhile please keep this manual for future reference The MICROH LED CHAMELEON V2 wash fixture is made of a new type of high temperature cast aluminum casing The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol This fixture is applicable but not limited to large scale live performances theater studio nightclubs and discos The MICROH LED CHAMELEON V2 wash fixture uses 36 powerful 1W LED s 12 Red 12 Green 12 Blue which feature high brightness and stability Please carefully unpack it when you receive the fixture and check if it was damaged during the transportation And please check whether the fol
6. The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1202 ON PIN3 PIN2 N S 6 MENU NAVIGATION To enter the menu press the A button one time Use buttons A amp B to move within the menu Use button B to select the function and to recall the next menu section To escape press the A button FUNCTION Manual mode i 1 LI Red dimmer 2 BLA Green dimmer 13 LIS Blue dimmer Auto mode 1 FLIG Flash 2 Fi q Automatic fade in and fade out 3 H C J Auto change 7 color Synchronization mode master and slave WEEE 1 Master light Choose same as manual auto sound control mode way 2 Alstave lighis DMKN CH Mode DMX 3CH Mode LAB p HV A clo PL a O LT HV A gL IL heor WA bL mbLO maida 7 DMX CHANNELS Mode 1 3 Channel s Channel 1 0 255 RED 0 100 Channel 2 0 255 GREEN 0 100 Channel 3 0 255 BLUE 0 100 Mode 2 4 Channel s Channel 1 0 255 DIMMER 0 100 Channel 2 0 255 RED 0 100 Channel 3 0 255 GREEN 0 100 Channel 4 0 255 BLUE 0 100 Mode 3 6 Channel s Channel 1 0 255 DIMMER 0 100 Channel 2 0 255 RED 0 100 Channel 3 0 255 GREEN 0 100 Channel 4 0 255 BLUE 0 100 Channel 5 STROBE 0
7. he power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective It should decrease gradually Please do not project the beam onto combustible substances Fixtures cannot be installed on or near combustible substances Keep more than 50cm distance from wall for proper ventilation and air flow If your fixture is or has become damaged in any way it shall be exclusively replaced or repaired by the manufacturer to avoid any hazard CAUTION Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock CAUTION The electric connection must only be carried out by a qualified electrician 3 OPERATION INSTRUCTIONS Do not turn on the fixture if it has been through severe temperature differences Damage may occur to the fixture Wait until unit is at room temperature to operate The unit should be protected from any vibration or agitation during transport Do not expose the fixture in any excessive heat when installing Do not lay any power cables on the floor It may cause electronic shock or damage to persons or equipment Make sure to attach the safety chain cable when installing the fixture Make sure the fixture is operated and installed by qualified personnel Keep the original packaging in case of defective product
8. lowing items are included inside the box Fixture One User Manual One 2 SAFTEY INSTRUCTIONS CAUTION ELECTRIC SHOCK WARNING USE EXTREME CAUTION WHEN HANDLING WIRES This device has left the factory in perfect condition In order to maintain this condition and to ensure safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual FS Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature and is dry This device falls under protection class therefore it is essential that the device be grounded The electrical connection must be carried out by a qualified technician The device should only be used with rate voltage and freguency Make sure that the available voltage is not higher than 120V as stated at the end of this manual Make sure the power cord is never crimped or damaged in any way as this could cause shock and damage If your power chord is damaged in any way please purchase a new cable from your local MICROH dealer Always disconnect power when the device is notin use or before cleaning it Never pull out the plug by tugging t
9. n V2 has 3 4 or 6 channel modes To change channel modes press the A button until cHn is displayed Press the B button until desire channel is displayed COLOUR FADE MODE Press and release the A button until FAd is displayed Press the B button to select desired speed from 0 to 9 9 is maximum COLOUR CHANGE MODE Press and release the A button until Ac is displayed Press the B button to select desired speed from 0 to 9 9 is maximum STROBE MODE Press and release the A button until FLA is displayed Press the B button to select desire speed from 0 to 9 9 is maximum MANUAL MODE In this mode Chameleon V2 can change the brightness intensity of Red Green and Blue colours To change red colour press and release the A button until rL is displayed Press the B button to edit brightness from 0 to 9 9 is maximum To change green colour press and release the A button until gL is displayed Press the B button to edit brightness from 0 to 9 9 is maximum To change Blue colour press and release the A button until bL is displayed Press the B button to edit brightness from 0 to 9 9 s maximum 4 MOUNTING AND INSTALLATION Caution For added protection mount the fixtures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personnel Before mounting the fixture to any surface make sure that the installation area can hold a
10. th unbalances 4 The electric power supply cables must not show any damage or material fatigue Further instructions depending on the installation spot and usage must be handled by a skilled installer or technician Any safety issues must be resolved CAUTION DISCONNECT POWER BEFORE SERVICING In order to keep the fixture in good condition and extend the life we suggest regular cleaning to the fixture 1 Clean the fan each week 2 A detailed electrical check by approved technician every three months is advised Ensure the circuit contacts are in good condition and prevent from overheating We recommend a thorough cleaning of the device by an approved service technician There are no serviceable parts inside the device Should you need any spare parts please order genuine MICROH parts from your local dealer IF YOU SHOULD EXPERIENCE ANY PROBLEMS OR ISSUES PLEASE CONTACT MICROH PROFESSIONAL PRODUCTS BY EMAIL AT info microhpro com In the event that your unit is defective in any way please contact your local dealer to obtain an RA number for service repair DISCLAIMER MICROH believes that the information contained within this user manual is accurate However Microh is not responsible for any error or addendums to this manual If you have any comments or general suggestions on how this manual can be improved please contact info microhpro com Thank you 10 Ori PROFESSIONAL PRODUCTS www microhpro com
Download Pdf Manuals
Related Search