AXIS T8331 PIR Motion Detector Series User Manual
Contents
1. AXISA COMMUNICATIONS AXIS T8331 PIR Motion Detector Series User Manual About this Document This manual is intended for administrators and users of AXIS T8331 PIR Motion Detector Series It includes instructions for using and managing the product on your network Later versions of this document will be posted at www axis com Legal Considerations Video and audio surveillance can be regulated by laws that vary from country to country Check the laws in your local region before using this product for surveillance purposes Liability Every care has been taken in the preparation of this document Please inform your local Axis office of any inaccuracies or omissions Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice Axis Communications AB makes no warranty of any kind with regard to the material contained within this document including but not limited to the implied warranties of merchantability and fitness for a particular purpose Axis Communications AB shall not be liable nor responsible for incidental or consequential damages in connection with the furnishing performance or use of this material This product is only to be used for its intended purpose Intellectual Property Rights Axis AB has intellectual property rights relating to technology embodied in the product described in this document In2. configured as input 4 O configured as input Note e This connection requires a camera with at least two configurable I O ports This connection requires changes in the terminal see AXIS T8331 PIR Motion Detector Series Terminal Connections on page 10 12 User Manual Ver M1 13 AXIS T8331 PIR Motion Detector Series Date November 2015 Axis Communications AB 2015 Part No 1518265
3. particular and without limitation these intellectual property rights may include one or more of the patents listed at www axis com patent htm and one or more additional patents or pending patent applications in the US and other countries Equipment Modifications This equipment must be installed and used in strict accordance with the instructions given in the user documentation This equipment contains no user serviceable components Unauthorized equipment changes or modifications will invalidate all applicable regulatory certifications and approvals Trademark Acknowledgments AXIS COMMUNICATIONS AXIS ETRAX ARTPEC and VAPIX are registered trademarks or trademark applications of Axis AB in various jurisdictions All other company names and products are trademarks or registered trademarks of their respective companies Disposal and Recycling When this product has reached the end of its useful life dispose of it according to local laws and regulations For information about your nearest designated collection point contact your local authority responsible for waste disposal In accordance with local legislation penalties may be applicable for incorrect disposal of this waste Europe G wmm his symbol means that the product shall not be disposed of together with household or commercial waste Directive 2012 19 EU on waste electrical and electronic equipment WEEE is applicable in the European Union member states To prevent potenti
4. state is to Grounded circuit 4 Press Save Note If the port is used in an event it is not possible to switch between Input and Output until the event is changed or removed It is only possible to manually set Input or Output if the camera provides two or more configurable I O ports Event Configuration 1 Go to the Events setup page and select Action Rules 2 Select Add 3 Type in a name for the Action Rule 4 Select Input Signal from the Trigger drop down list Select Digital Input Port from the drop down list below Select 1 or 2 from the drop down list below Make sure Active is set to Yes 5 Select a value from the Schedule drop down list Always is selected by default or manually set a value by select New schedule 6 Select an action from the Type drop down list 7 Press OK in order to save the Action Rule The Action Rule will now be in the list of Action Rules Walk Test It is recommended to perform a walk test after installation to confirm that the PIR sensor is working properly Before the test make sure the PIR sensor is configured as below Set the photocell to DAY default setting e Set the Pulse count switch to TEST e Set the LED switch to ON default setting This applies to AXIS T8331 only After the warmup period is completed approximately 60 s conduct a walk test by moving in the detection zone of the PIR sensor The LED lights when the PIR sensor detects a moving object AXIS T
5. 8331 PIR Motion Detector Series Functions After the test configure the PIR sensor as below e Set the photocell according to the environment DAY is the default setting and is recommended for most applications e Set the Pulse count switch to 2 e Set the LED switch to ON or OFF See LED switch on page 5 for more information about the LED This applies to AXIS T8331 only Masking Strips Below text applies to AXIS T8331 E only Unwanted detection zones can be eliminated by masking the lens with provided masking strips 1 Remove the cover 2 Apply the masking strip to the zones that should be excluded Day Night Mode Adjustment Below text applies to AXIS T8331 E only The Day Night Mode switch can be used to adjust the detector according to the brightness of the surrounding area For best performance it is recommended to set the dial to DAY default setting To have the detector begin to function only after it has become dark turn the dial gradually to the NIGHT side For position of the Day Night Mode switch see Hardware Overview on page 8 LED switch Below text applies to AXIS T8331 only For AXIS T8331 it is possible to set the LED switch to OFF ON By default the switch is set to ON When in this mode the LED will lit when triggered When set to OFF the LED will not be lit when triggered For position of the LED switch see Hardware Overview on page 8 Pulse Count Switch Below text applies to both AXIS T8331 a
6. ages of the terminal connection for AXIS T8331 E The left image shows the default connection with tamper and alarm together 10 AXIS T8331 PIR Motion Detector Series Reference Material The right image shows a connection with tamper and alarm separated This connection requires a camera with at least two configurable 1 0 ports AXIS T8331 E For position of the terminals see Hardware Overview on page 8 AXIS T8331 PIR Motion Detector Series Schematics Below is a schematic showing the connection with a camera and the PIR sensor This is the default connection with tamper and alarm together Pin 3 Pin 1 GND Pin 2 Power Pin 4 not used Camera NE PIR 0 p Supply of PIR gt E J E N PIR Alarm N C Pod N Tampering Switch N C 3 ff lt o TRE snc me 1 GND 2 Power 3 1 0 configured as input 4 Not used Below is a schematic showing the connection with a camera and the PIR sensor In this connection tamper and alarm are separated Pin 3 alarm Pin 4 tamper Pin 1 GND Pin 2 Power 11 AXIS T8331 PIR Motion Detector Series Reference Material X Supply of PIR 2 x Jj e E a KO PIR Alarm N C E 3 mE 4 e o gt AS Tampering Switch N C 4 4 e o 1 GND 2 Power 3 1 0
7. al harm to human health and the environment the product must be disposed of in an approved and environmentally safe recycling process For information about your nearest designated collection point contact your local authority responsible for waste disposal Businesses should contact the product supplier for information about how to dispose of this product correctly This product complies with the requirements of Directive 2011 65 EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment RoHS China G This product complies with the requirements of the legislative act Administration on the Control of Pollution Caused by Electronic Information Products ACPEIP Contact Information Axis Communications AB Emdalav gen 14 223 69 Lund Sweden Tel 46 46 272 18 00 Fax 46 46 13 61 30 www axis com Support Should you require any technical assistance please contact your Axis reseller If your questions cannot be answered immediately your reseller will forward your queries through the appropriate channels to ensure a rapid response If you are connected to the Internet you can e find answers to resolved problems in the FAQ database Search by product category or phrase report problems to Axis support staff by logging in to your private support area chat with Axis support staff visit Axis Support at www axis com techsup Learn More Visit Axis learning center www
8. axis com academy for useful trainings webinars tutorials and guides AXIS T8331 PIR Motion Detector Series Table of Contents Functions drake I O and Event Configuration Sue eat MEISTEN TT Masking Strips ee sie ne once mtem meg ren Re en d Paname E Day Night Mode Adjustment 52424222 4 uns disons teens LED switch 44 444 j Bl n eue Pulse Count SWITEN eer Rem ett mask et Re espece Sensitivity SWITCH sce csc wager emen ege a by ex rk ex d RR UR m RR a Detection Area Adjustment KE ae crm Reference Material auuuunnnuuuunununuunnnnnruunnmnmnmmn Hardware Overview 444444444 RR RR RR RR re AXIS T8331 PIR Motion Detector Series Graphs AXIS T8331 PIR Motion Detector Series Terminal Connections 10 AXIS T8331 PIR Motion Detector Series Schematics 11 O0 O O O 01010101 A I SH AXIS T8331 PIR Motion Detector Series Functions Functions I O and Event Configuration Below text applies to both AXIS T8331 and AXIS T8331 E This section contains information of I O configuration and Events on the Camera For more information and specifications about the products I O and Event functionality see the products User Manual available on www axis com I O Port Configuration 1 Go to Setup System Options Ports amp Devices I O Ports 2 Set port 1 to Input default 3 Set Normal
9. itch Tamper switch PIR sensor do not touch Sensitivity switch Terminals AN DAARWNH AXIS T8331 PIR Motion Detector Series Graphs AXIS T8331 graph 5 10 15 20 2 30 35 40ft lende 4 i i 10 2 JS ut 1 a 1 5 0 0 15 2 SR RN ip NR 10 f a EE ER EE 15 BR 20ft 2 4 6 8 10 12m AXIS T8331 PIR Motion Detector Series Reference Material The large graph above shows a top view of the detection zones The small graph above shows a side view of the detection zones when the PIR sensor is mounted on a height of 2 4 m Ideal mounting height is between 1 5 m to 2 4 m AXIS T8331 E graph 83 ft 5ft 1 0 JE 10 E ao ds 9 40ft 83 ft The large graph above shows a top view of the detection zones The small graphs above shows a side view of the detection zones Multi level area and Pet alley area AXIS T8331 PIR Motion Detector Series Terminal Connections AXIS T8331 Below are images of the terminal connection for AXIS T8331 The left image shows the default connection with tamper and alarm together The right image shows a connection with tamper and alarm separated This connection requires a camera with at least two configurable 1 0 ports AXIS T8331 For position of the terminals see Hardware Overview on page 8 AXIS T8331 E Below are im
10. nd AXIS T8331 E AXIS T8331 PIR Motion Detector Series Functions The Pulse Count switch can be set in two different modes 2 or TEST Mode 2 is the default mode and is recommended to use TEST is only used when performing a walk test For position of the Pulse Count switch see Hardware Overview on page 8 Sensitivity Switch The Sensitivity switch can be used to adjust the sensitivity of the detector There are three different modes M Medium This is the default position and can be used for normal applications e H High Use this when the application requires high sensitivity When using AXIS T8331 E in Pet Alley Area mode it is recommended to set the sensitivity mode to H e Low Use this in applications that may be unstable For position of the Sensitivity switch see Hardware Overview on page 8 Detection Area Adjustment Below text applies to AXIS T8331 E only For AXIS T8331 E it is possible to set the detection area There are two different modes e Multi Level Area This is the default mode and is applicable to normal applications Pet Alley Area This mode provides a horizontal detection pattern with no declination of zones allowing pets to move through the area Note Ideal mounting height for Pet Alley Area is 1 2 m to 1 5 m See AXIS T8331 PIR Motion Detector Series Graphs on page 9 for graphs of Multi Level Area and Pet Alley Area See Hardware Overview on page 8 for position of the Detection Area screw and
11. the mirror See below for how to switch to Pet Alley Area mode 1 Carefully loosen the adjustment screw 2 Slide the cover down and fasten the screw at the P position 3 Flip the mirror to the upper position VMD and PIR AXIS Video Motion Detection VMD is an application for Axis camera products VMD can be used together with the PIR sensor The application detects moving objects within a predefined area of interest making it possible to automatically trigger an event AXIS T8331 PIR Motion Detector Series Functions Note The VMD detection area and the PIR sensors detection pattern are not synchronized by default VMD detection area can be set in a user interface The detection pattern for AXIS T8331 E can be modified by using the supplied masking strips For more information about AXIS Video Motion Detection see the products User Manual available on www axis com AXIS T8331 PIR Motion Detector Series Reference Material Reference Material Hardware Overview AXIS T8331 1 0 interface Terminals PIR sensor do not touch Sensitivity switch Tamper switch LED switch LED NOOaA WN AXIS T8331 E AXIS T8331 PIR Motion Detector Series Reference Material Day Night mode adjustment Mirror Photocell LED Detection area adjustment screw 1 0 interface Pulse count sw
Download Pdf Manuals
Related Search