Home

ACU-100

1. Fig 15 Configuration of the ACU 100 controller working together with the INTEGRA control panel in DLOADX program Given under information on the module type and address is the version of its firmware The wireless devices have been registered in the controller as recommended earlier in this manual the devices which occupy both zones and outputs in the system were added first while the devices taking up zones only were added after them 1 Launch the DLOADX program and establish communication with the control panel see PROGRAMMING manual for INTEGRA INTEGRA Plus or VERSA control panel 2 Click on the EH button to open the window showing structure of the security system 3 Select the Hardware tab and then highlight the wireless system controller in the list of devices 4 Program the controller ACU 100 SATEL 37 5 Having finished entering the new settings save them in the controller by clicking on the Write button the and buttons in the main menu of DLOADX program are not intended for reading writing the settings of the controller and wireless devices supported by it Such diagnostic functions as SIGNAL LEVEL COMMUNICATION QUALITY and RESTART COMMUNICATION TEST in the DLOADX program are available in the WIRELESS DEVICE window No Name Device wee Signal evel Connection quali 41 ASP 105 acoust s ASP 105 siren 0063248 100 100 42 ASP 105 opt s 0063248 100 100 APD 100 corridor
2. APD 100 detector APD 100 detector unused unavailable APD 100 detector APD 100 detector unused unavailable AMD 100 detector AMD 100 detector unused unavailable AMD 100 detector AMD 100 detector unused unavailable AMD 101 detector AMD 101 detector unused unavailable 1 2 3 4 5 6 7 8 A AMD 101 detector unused unavailable Table 8 An example of correct registration of wireless devices The system has reserved 8 zones and 8 outputs as well as 1 address for 8 devices The controller with address O is connected to the first expander bus Sometimes it is impossible to avoid gaps on the list of zones outputs This is the case when the number of zones outputs actually used by the devices is not a multiple of 8 Avoiding the gaps is difficult or even impossible when due to the size of the premises a number of ACU 100 controllers are operating in the system Apart from assignment of zones and outputs to the controller the panel will reserve for it an address on the expander bus For each group of 8 zones outputs 1 address is reserved on the expander bus The controller can take up from 1 to 6 addresses on the expander bus This should be taken into account at the system design stage and the sufficient number of unoccupied addresses should be left for the controller If after new wireless devices are 30 Two way wireless system ABAX ACU 100 added to the controll
3. 213 1 1 New device 213424 2 Config device 213434 3 Remove device 213444 4 Wirelss zones 213454 5 Synchronize 213464 6 Test mode on 213474 7 Test mode off For additional information please see the manuals delivered with the VERSA control panel 11 3 DLOADX PROGRAM Module ACU 100 address 8 IT version 4 03 2013 10 22 PL Name ACU 100 08h Tamper signaled in part 1 Living Room No auto reset after three module tamper alarms Response period 12sec C 24sec 36sec Higher sensitivity for jamming detection No Name Serial number ARU Always active Configuration Filter FOUT 41 i ASP 105 acoust Burglary ASP 105 siren 0063248 1 Sound 1 i 4 time 3 min QUT 42 ASP 105 optical Burglary flash APD 100 coridor Interior delayed with TAMPER amp PD 100 PIR PET 0052831 2 1 Sensitivity medium PET 40 APD 100 living r Interior delayed with TAMPER APD 100 PIR PET 0029418 2 1 Sensitivity medium PET 40 AMD 100 door Entry Exit with TAMPER AMD 100 Magn contact 0182233 O0 Bottom contact 40 Living r wind 1 Perimeter with TAMPER AMD 100 Magn contact 0032741 1 Side contact 40 Living r wind 2 Perimeter with TAMPER AMD 101 Magn contact 0193632 1 Side contact 40 Living r wind 3 Perimeter with TAMPER A NC input E Read EG Details Testmode amp 9 New device Sy Wie Pel X Synchronize 3 Remove device Comments
4. ACU 100 SATEL 21 hardwired zones and outputs of the control panel However it should be borne in mind that the actual sensitivity of the zones may be different from that programmed in the control panel from 20 ms to 140 ms it corresponds to sensitivity programmed in the control panel over 140 ms only some values are available 300 ms 500 ms 700 ms etc every 200 ms the programmed value is rounded off to that supported by the expander 5 1 2 Configuration of ACX 200 expander zones outputs for ACU 100 or ACX 201 controller operation with CA 64 control panel The expander occupies 4 zones in the alarm system Parameters of the zones are to be programmed in the same way as those of the other hardwired zones of the control panel The DLOAD64 program or the alarm system keypad can be used for this purpose You must take into account the same limitations regarding the zone sensitivity as in case of the expander working together with the INTEGRA INTEGRA Plus or VERSA control panel In order to configure the expander outputs indicate the corresponding ACU 100 control inputs which will control the expander outputs It can be done by means of the LCD keypad connected to the controller or through the DLOAD10 program The control inputs should be connected to the suitably programmed outputs of the control panel 5 1 3 Configuration of ACX 200 or ACX 201 expander zones outputs for ACU 100 controller operation with other contr
5. ELEBFOO0 ubeuj1qi4 Q0L JAY LEZZ ZO AH Hld OGL JHdYv L8ZEG00 1012919 q ea1g ssej5 OOL GN ZEJEG LO indui JN CEJEG LO 1281002 3noubeu 101 QWv Lr ze00 GEZEB LU BLFGEOO 1682500 SFCESD fysen uauts GOL d OOLNYY OOL NYY aBbeyoa ddns MEL owaw rea 9 paziuoiqau s UOREZUOJYJU G_ laduwe no L 0v 00 00 0E cL wou Bunsa 158 pesay x ES Jaunos qua 3 Pa l punos _ j8 91 Lo Buijeubis agnos 8a uoqeSlUnWWo Buluue ou Bure p asg e aspe J 28s7 J ponad asuodsay XXXXXXXXXXXXXXXX jeynuep e al o gx te d djs uoqedunwuioj pued oquoj apy ACU 100 SATEL 41 ACU 100 Actual signal level E 15 x 5 ASP 205 amp ASP 205 7 ASw 100 amp APD 100 3 APD 100 10 AMD 101 11 AMD 101 12 AMD 101 13 AMD 101 14 ARF 100 1 ACX 200 2 ACX 200 3 ACX 200 4 ACX 200 Fig 19 DLOAD10 program window with a diagram of the level of radio signal received by the controller 11 6 DESCRIPTION OF FUNCTIONS OPTIONS AND COMMANDS Identifier the identifier in the DLOAD10 program is intended to protect the controller against an attempt of unauthorized reprogramming The identifier consists of 16 characters By default these are O only They can be substituted by digits from O to 9 and or letters from A to F rang
6. duration of alarm signaling by the buzzer LED 1 3 6 or 9 minutes 13 2 8 ARD 100 detector The A and V keys enable sensitivity to be selected within the range from 1 to 16 1 minimum 16 maximum 13 2 9 ATD 100 detector Use the 4 and b keys to navigate between the programmable parameters of the detector Use the numeric keys to program the following temperature a value from the 30 C to 70 C range with up to 0 5 accuracy to enter the preceding sign press one of the numeric keys from 3 to 9 tolerance a value from the 0 5 C to 10 C range with up to 0 5 accuracy threshold type H high or L low 13 2 10 ASP 105 siren After selecting the first position the first zone occupied by the siren define the parameters of acoustic signaling Use the 4 and gt keys to navigate between the parameters and the A and V keys to modify them The following should be programmed type of acoustic signaling a choice out of four types is provided 50 Two way wireless system ABAX ACU 100 maximum duration of signaling 1 3 6 or 9 minutes 13 2 11 ASP 205 siren Signaling parameters can be independently selected for both positions zones occupied by the siren Use the 4 and gt gt keys to navigate between the parameters and the A and W keys to modify them The following should be programmed operating mode of acoustic signaling it can be disabled the symbol displayed or
7. A B C D DIP switches for setting the controller address in the same way as with the CA 10 zone expanders When in the ON position the switch value is 1 A1 A2 A3 A4 As DIP switches for setting the controller address In order to determine the controller address add up the values set on individual DIP switches as per Table 3 DIP swith number switch number Numerical value for switch in ON position Table 3 X unused DIP switch ACU 100 SATEL 7 2 3 CONTROL INPUTS A If the controller is working as an expander with the INTEGRA INTEGRA Plus or VERSA control panel you are not required to know how the control inputs operate because they need not be connected to the control panel all information will be sent to the control panel via communication bus The ACU 100 PCB incorporates 4 control inputs dedicated to controlling the operation of wireless devices detectors sirens etc The controller inputs can be programmed as NO normally open or NC normally shorted to ground Changing the input status shorting to or isolating from ground has effect on operation of the wireless devices controlled by that input for each wireless device registered in the controller you must indicate an input which will control its operation The number of inputs can be increased by connecting the ACX 100 expansion modules to the controller The number of control inputs in the ABAX system can be up to 24 controller 5
8. APD 100 PIR PET 0052891 100 100 APD 100 living r APD 100 PIR PET 0023418 100 __ 100 AMD 100 door AMD 100 Magn contact 0182239 100 __ 100 Kitchen window AMD 100 Magn contact 0032741 100 100 a Living r wind 1 AMD 101 Magn contact 0193632 100 100 Ew Living r wind 2 0193632 100 _ 100 AGD 100 Glass Break Detector 0053281 100 100 ra APMD 150 garage APMD 150 PIR MW 0247231 100 100 EN Garage window AVD 100 Magn contact 0048213 100 100z Garage window 2 js 0048213 100 100 eee on diagnostics Test restart m Testes fis Read communication log Testing since 5 h 45min Fig 16 DLOADX program window showing signal level and quality of controller communication with wireless devices ACU 100 controller working together with the INTEGRA control panel Troubles of wireless devices no communication low battery level jamming can be read out in the DLOADX program in the TROUBLES window 11 4 LCD KEYPAD CONNECTED TO CONTROLLER 1 Set the option of programming by means of LCD keypad on the DIP switches on the controller electronics board 2 Connect the keypad to the controller see CONNECTING KEYPAD TO CONTROLLER 3 Enter the service code and confirm by pressing the key to get access to the menu of controller service functions 4 Program the controller as required 5 Quit the service mode using the SERVICE END 6 Disconnect the keypad 11 4 1 Service mode o
9. Reconnect the cables to the controller communication bus Reconnect the controller power supply 15 SPECIFICATIONS Operating frequency bBa d a KAKA AKA 868 0 MHz 868 6 MHz Number of supported wireless devices aaa aaa aaa aaa aaa aaa aaa aaazaaaaaaaaaa aaa aaazzznec 48 rM up to 500 m in open area ee Eris DM 12 V DC 15 Standby current COMSUMPM ON rr 140 mA Maximum current eonsumpliofl sess e serv sversees EFELRRNEREFEFRREREERRRRENERERRHERREKRRRERENR REREREERRRSP REA 140 mA Outputs current carrying capacity ea iab t sete a sec PRACE PE 50 mA Security grade according to EN50131 3 aepo brides d OD ERE SE aat d Hn BER nd DE WR Grade 2 ACU 100 SATEL 51 Environmental class according to EN50130 5 cece cette ee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees Operating temperature range lecce cccccccccccccceccserersus 10 C 55 C Maximum humidity s s bd daa id etae er etre mr IG ERES Cha Lr aL CRIN CER S RAA 931396 Complied with standards EN 50130 4 EN 50130 5 EN 50131 1 EN 50131 3 EN 50131 5 3 Electronics board dimensions cccceceeecceeeeeeeeseeeeeeeceeeeeeeaseeeeeeeeeeeeeaaeeess 104 x 73 mm Housing dimensions OPU 1 A ssssssssssssseeeeeeennee 126 x 158 x 32 mm WEIGNE da e e ge alea ei tS fe nies ever erates ureter RI er rer ARI Nt eu I ED du INE n NEL E PIE 222g Name
10. 5100ms range Within the range of 20ms to 140ms it is possible to enter values every 20ms 20ms 40ms 60ms etc The next value that can be entered is 300ms Within the range of 300ms to 5100ms you can enter values every 200ms 300ms 500ms 22 Two way wireless system ABAX ACU 100 700ms etc If a number different from the above values is entered it will be rounded up to the next supported value e g after entering 301 the next value to be entered is 500ms In order to configure the expander outputs indicate the appropriate ACU 100 control inputs which will control the expander outputs The control inputs are to be connected to the suitably programmed outputs of the alarm control panel 6 WIRELESS DETECTORS IN ABAX SYSTEM The wireless detectors send information on violations tampers and battery status to the ACU 100 controller Two detector operating modes are available passive mode the battery saving mode in which information on violations and battery status is sent to the controller exclusively during the response period see the RESPONSE PERIOD parameter only the tamper information being sent immediately The detectors can work in the passive mode when the alarm system is disarmed active mode all information is sent to the controller instantly Note The AMD 103 detector always remains in the active mode If the controller works as an expander of the wireless devices for INTEGRA INTEGRA Plus or
11. ACX 100 modules In order to control the ACU 100 controller inputs you can use any alarm control panel outputs OC high current low current relay type Where the control is effected by means of the high current output of a SATEL made control panel it is necessary to connect a 1 1kO resistor to the controller input see Fig 2 OUT4 reversed polarity 0 V when active AR1 NO type o R N lt 4 SQ U u Q e Fig 2 Example of connecting the high current output of SATEL made control panel to the control input The control panel outputs which are to control the ACU 100 controller inputs should be properly configured their type polarity cutoff time etc The type of wireless devices whose operation is controlled by the input must be primarily taken into account To control operation of the wireless detectors the control panel output can be programmed e g as the ARM STATUS Arming the control panel will switch the detectors into the active mode and disarming into the passive mode detector operating modes are described in section WIRELESS DETECTORS IN ABAX SYSTEM It should be remembered that 8 Two way wireless system ABAX ACU 100 activation deactivation of the detectors is delayed in relation to arming disarming see WIRELESS DETECTORS IN ABAX SYSTEM By having programmed the exit time in the control panel you can avoid delay in activ
12. MODE STRUCTURE HARDWARE EXPANDERS gt SETTINGS gt controller name gt Use ARU 100 2 Using the W and A keys select the zone to which the wireless device is assigned and then press 3 Using the W and A keys select whether the wireless device is to communicate with the controller directly or via a selected repeater the name of zone to which the repeater is assigned is displayed on the list 4 Press to confirm your selection 13 CONFIGURATION OF ADDITIONAL PARAMETERS AND OPTIONS IN WIRELESS DEVICES 13 1 DLOADX OR DLOAD10 PROGRAM Additional parameters and options are to be programmed in the Configuration column 13 1 1 APD 100 detector For detectors with firmware version 2 01 enter a 2 digit sequence The first digit relates to sensitivity see Table 10 and the second one to the pet immunity option 0 option disabled 1 option enabled For detectors with older firmware enter a digit from 1 to 3 which corresponds to the selected sensitivity see Table 10 Number Detector sensitivity low medium high Table 10 46 Two way wireless system ABAX ACU 100 13 1 2 APMD 150 detector Enter a 3 digit sequence 1 digit sensitivity of PIR sensor from 1 to 4 1 minimum 4 maximum 2 digit sensitivity of microwave sensor from 1 to 8 1 minimum 8 maximum 3 digit type of operation in the test mode 0 signaling violation after motion is detected by b
13. OUT7 OUT8 COM AR1 AR2 AR3 AR4 Fig 1 Schematic view of ACU 100 controller PCB version 4 00 antenna 2 DIP switch package for setting an individual addresses of the device and to configure some working parameters of the controller see FUNCTIONS OF DIP SWITCHES 3 buzzer It informs of occurrence of one of the problems signaled on functional outputs it does not apply to the controller interfacing with the INTEGRA INTEGRA Plus or VERSA series alarm control panels ACU 100 SATEL 5 4 RS 232 port with opto isolation It enables a PC computer with DLOAD10 program to be connected for the time of programming 5 RJ type socket It allows to connect an LCD keypad for the time of programming The controller interfaces with LCD keypads for operating the CA 64 or INTEGRA INTEGRA Plus series control panels Notes e The controller cannot be simultaneously programmed by means of computer and LCD keypad e When working with the INTEGRA INTEGRA Plus or VERSA alarm control panels the controller can be programmed by means of the control panel with no need for connecting the keypad or computer to the controller sockets 6 tamper contact It is activated by enclosure cover removal 7 LED indicator It indicates the controller status The mode of lighting depends on the controller working configuration e interaction with CA 64 INTEGRA INTEGRA Plus or VERSA alarm control panels green steady light no communi
14. and magnetic contact sssessseeeeese 11 3 13 ASD 100 Wireless smoke and heat detector sse 11 3 14 ASD 110 Wireless smoke and heat detector sse 11 3 15 ARD 100 Wireless reorientation detector ssssssssssssssssseeeemeemeennnn 12 3 16 ATD 100 Wireless temperature detector sss 12 3 17 ASP 105 Wireless outdoor Siren si eee o aa ea e Erea e Ea a enne 12 3 18 ASP 205 Wireless indoor siren eee eee eee aaa aa 12 3 19 APT 100 Bidirectional KeyroDbc sis e Idee RA EC ces ene Rie ED m BERNER REN SPERM PA 12 3 20 ASW 100 E 230 V AC Wireless controller ssssssssssssssseemem meme 13 3 21 ASW 100 F 230 V AC Wireless controller essem 13 3 22 ARF 100 Radio signal level tester 0 c ccccceeeesececceeeeeeecenesdecthocseneeeeseseeacueneceeteddennedeneneeeee 13 3 23 ARU 100 Radio signal repealer er a ettet pe eec a OE Ea pi deni n PE ceeds 13 42 Installato docte tein c eto reo ap bier Be eod i en webu De Ri bo su onto or a ed dubs Gad nein ira Cog OOOO GA 13 4 1 Installation of ACU 100 wireless system controller ssseeeee 14 4 2 Connecting LCD keypad to the controller ceseseeceecccceeeeeteneeeeeneneeeeneeeeseneeeeeseeeneeeeeeeseees 14 4 3 Connecting computer to the controller 2 GAL C a eee tecets 15 4 4 Connecting the ACX 100 input 8 output expans
15. check the trouble by means of the LCD keypad connected to the controller start the BATTERY STATUS function SERVICE MODE TESTS BATTERY STATUS The first device on the list in which a problem has been diagnosed will be displayed The ACX 201 expander occupies 4 positions on the list of devices The Low battery message for the first item occupied by the expander means overloading of the AUX1 or AUX2 supply output for the second item discharged battery for the third item loss of AC supply The battery status information in the DLOAD10 program is displayed in on line mode The information display logic is identical to that in the LCD keypad connected to the controller The first item on ten list in the Battery column refers to the status of AUX1 amp AUX2 supply outputs the second one to the battery status and the third one to the AC supply status Note The EN50131 3 standard requires that zones must react to signals lasting more than 400 ms It means in case of the ACX 200 expander that no values exceeding 300 ms should be entered when programming the sensitivity the higher the value the lower the sensitivity 5 1 1 Configuration of ACX 200 or ACX 201 expander zones outputs for ACU 100 controller operation with INTEGRA INTEGRA Plus or VERSA control panel The expander occupies 4 zones and 4 outputs in the security alarm system Parameters of the zones and outputs are to be programmed in the same way as those of the other
16. eight output in the first group of 8 outputs and the first output in the second group of 8 outputs INTEGRA INTEGRA Plus ACU 100 List of devices APD 100 detector zones Device APD 100 detector outputs Device unused unavailable APD 100 detector APD 100 detector unused unavailable AMD 100 detector AMD 100 detector unused unavailable AMD 100 detector AMD 100 detector unused unavailable AMD 101 detector AMD 101 detector unused unavailable A AMD 101 detector unused unavailable unused unavailable unused unavailable 1 2 3 4 5 6 7 8 ASP 105 siren ASP 105 siren ASP 105 siren ASP 105 siren ASP 105 siren unused unavailable unused unavailable unused unavailable unused unavailable unused unavailable unused unavailable unused unavailable unused unavailable unused unavailable unused unavailable unused unavailable unused unavailable unused unavailable unused unavailable Table 7 An example of incorrect registration of wireless devices The system must reserve 16 zones and 16 outputs as well as 2 addresses for devices taking up 8 items The controller with address 0 is connected to the first expander bus INTEGRA INTEGRA Plus ACU 100 List of devices ASP 105 siren zones Device ASP 105 siren outputs Device ASP 105 siren A ASP 105 siren ASP 105 siren
17. input numbers Output numbers Table 4 4 5 ADDING NEW WIRELESS DEVICES Notes e The procedure of adding wireless devices for the controller interacting with the VERSA control panel is described in the installer manual of the control panel e In the controller connected to the VERSA control panel you cannot add the ARU 100 repeater using the DLOADX program or keypad connected to the control panel In order to add the repeater connect the computer to the RS 232 port of the controller and use the DLOAD10 program on the DIP switches temporarily set the mode of interfacing with any control panel and programming by means of the DLOAD10 program e If the controller operates with the INTEGRA firmware version 1 09 or newer or INTEGRA Plus control panel you can select in case of some wireless devices whether it will take one or two positions channels in the list of devices Depending on the device if one position is selected AMD 102 only additional inputs will be supported roller shutter and NC ATD 100 you will only be able to program one temperature threshold AVD 100 only vibration detector will be supported 4 5 1 DLOAD10 and DLOADX programs In order to add a new wireless device to the system do the following 1 Press the NEW DEVICE button in the program 2 A window will appear in which you should enter the 7 digit serial number of the device being added The serial number can be found on the
18. interaction between controller and VERSA control panel is contained in the manuals delivered with the control panel addressable zone expander able to work in conjunction with the CA 64 control panel zone expander able to work in conjunction with the CA 10 control panel module of wireless devices able to work in conjunction with any alarm control panel 10 1 EXPANDER OF WIRELESS DEVICES INTEGRA INTEGRA PLus Set the suitable operating mode and address of the controller on DIP switches address operating mode 4 INTEGRA INTEGRA Plus control panel Fig 7 Example of setting the DIP switches 28 Two way wireless system ABAX ACU 100 INTEGRA 64 INTEGRA 128 PTE Zi COM EX1 DT1 CK1 Durs ED ACU 100 o o ae N lt U U DDDDDDDDDDDDDDDDOZC TPR CON JAM LBA OUT1 OUT2 OUT3 OUT4 OUTS OUT6 OUT7 OUT8 COM AR1 AR2 AR3 AR4 Fig 8 Example of connecting the ACU 100 controller to the INTEGRA control panel Communication with the control panel is only effected by means of the communication bus This way is used for transmission of information on violations of detectors tampers and troubles of wireless devices as well as for control of operation of wireless devices Table 6 shows how the terminals of the controller communication bus should be connected to the communication bus terminals of the INTEGRA INTEGRA Plus alarm control
19. of certification body a acetate i pq iq oq iq qq eqq qe qu Debe baee Dis Telefication 16 HISTORY OF THE MANUAL UPDATES Described in the table below are changes as compared with the manual for the ACU 100 controller with firmware in version v1 03 FIRMWARE DATE VERSION INTRODUCED CHANGES 2005 09 1 04 e Added information on the options of programming the outputs of the controller and ACX 100 module as NO NC type p 8 and 43 e Added description of the manner to indicate active status of functional outputs p 9 e Supplemented service mode menu of the LCD keypad connected to the controller p 38 2006 11 1 05 e Information about new wireless devices added to section on controller outputs p 8 e Information added regarding new wireless devices of ABAX system ACX 200 zone output expander p 9 and 20 ASP 205 wireless indoor siren p 12 ASW 100 E and ASW 100 F 230 V AC wireless controllers p 13 and 26 and ARF 100 radio signal level tester p 13 and 26 e Modified section on adding new devices to ABAX system p 17 19 e Supplemented section on interaction between ACU 100 controller and INTEGRA control panels p 27 e Added information on the diagnostic capability of ACU 100 controller operating in configuration of expander of wireless devices for INTEGRA series control panels by means of DLOAD10 program p 35 and 39 e Supplemented information on Test mode p 43 2007 11 1 06 e Supplemen
20. open the window showing the radio signal level click on the button Also the level of radio signal received by the controller from individual devices can be represented in a diagrammatic form Note When the ACU 100 controller is connected to the INTEGRA INTEGRA Plus control panel the options regarding configuration of wireless devices are not available in the DLOAD10 program Available are only diagnostic functions including diagrams illustrating the radio signal levels 100 ACU way wireless system ABAX Two 40 wesboid QL avo1q eui ui MOpUIM GuqeJsdo Je oquo2 OOL NOV 8L 514 TWOJ p aalaap aaoway UDREZIUCIYDU G 2104 70v aslasp may f E apow sa ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON pe ec ce le De bic ZCL SLPLELZL LEOL 6 8 2r AAA 8r Ly Or Gy tw Ce Cb ib Op GE SE LE OE GE vt tt ZE le OF Ez S2 UZ SZIN JON 9 z cz zz kz OF 6b 8 Lb OL Gb bh EL ZL HL O 6 sndn 00L 00L 00L 00L 00L 00L 00L 00L 00L 00L 00L Z L 8 8 9 S L t t E F jenb PITT a PUBIS tiene g Puuadwe 1L ewszepoy i dui onuo 3 JET asjnd z AyAnisuas E Z joejuoo woyog 0 MAH HId 3591 LAY AIANSUBS gg MIANISUAS Q wnpaw AAHISUBS z joejuos api joejuos epis joejuoa wojog g l3d unpau fyanisues 7 l3d unipau Myanisuas z UNI SUI punos p zeSrS00 ZEGPGOD L mwsuena Q0L NHY ELEBFOO
21. output 16 3 CLK2 CLK4 f CLK3 keypad keypad keypad keypad in controller in controller Table 9 Control of the detectors changeover to active passive state sirens triggering alarm signal 230 V AC controller closing opening the electric circuit etc is performed through the control inputs of the ACU 100 controller Suitably programmed outputs of the alarm control panel should be connected to the control inputs Additionally it is possible to connect the first eight outputs of the controller to the control panel zones Thus the alarm control panel can receive information from the wireless devices assigned to these outputs Connecting the ACU 100 controller to the CA 10 control panel at the same time by means of communication bus and control panel zones will enable the system to be expanded by up to 14 wireless zones Fig 12 shows an example of configuration of the ACU 100 controller interacting with the CA 10 control panel One keypad is connected to the control panel therefore the CLK controller terminal is connected to the CLK2 panel terminal The zones made available by the ACU 100 controller to the control panel by means of the communication bus have in the security system numbers from 11 to 16 controller outputs from 11 to 16 These zones should be programmed in the control panel as 2EOL NO type The controller outputs OUT1 and OUT2 have been connected respectively to the control panel zones Z1 and Z2 thus the total number of
22. panels ACU 100 controller terminals 020 7 12V CLK DAT EX INTEGRA 24 INTEGRA 32 COM or CK DT Panel AUX terminals INTEGRA 64 INTEGRA 128 INTEGRA 64 Plus INTEGRA 128 Plus INTEGRA 256 Plus Table 6 Having connected the ACU 100 controller to the control panel start the expander identification function in the panel In the process of addition or removal of the wireless devices it must be borne in mind that during controller identification the INTEGRA INTEGRA Plus series control panels register the zones and outputs by groups of 8 Therefore it is important at the registration of wireless devices in the controller to maintain continuity i e to avoid spaces in the list which will eventually reduce the number of available inputs in the panel For example if 9 wireless devices were initially registered in the controller but item 7 was later deleted from the list the control panel will assign 2x8 zones to the controller although just 8 devices will be physically connected to it see Table 7 In case of devices which in addition to zones also take up outputs it is recommended that they be added to the system first so as to maintain the continuity of using both the zones and the outputs Table 7 presents a situation in which the first output of the siren has found itself in ACU 100 SATEL 29 position 8 and the second output in position 9 As a result 16 outputs have been reserved in the system the
23. programmed number of pulses within the 1 to 8 range pulse validity 30 120 or 240 seconds or unlimited duration on the display i e only switching over the detector from passive in to active state will reset the pulse counter 13 2 5 AGD 100 detector The A and V keys enable sensitivity to be selected within the 1 to 3 range see Table 10 13 2 6 AVD 100 detector After selecting the first position the first zone occupied by the AVD 100 the A and W keys allow you to indicate the active reed switch of the magnetic contact After selecting the second position the second zone occupied by the AVD 100 detector the parameters of the vibration detector can be configured The lt and gt keys allow you to navigate between the parameters and the A and VW keys to modify them The following should be programmed sensitivity within the range from 1 to 8 1 minimum 8 maximum number of pulses within the range from 0 to 7 13 2 7 ASD 100 detector The 4 and gt keys allow you to navigate between the programmable detector parameters and the A and W keys to modify them The following should be programmed operating mode of the heat sensor you can disable the sensor the symbol displayed or select the detection class A1 A2 or B acc to the standard EN 54 5 operating mode of the buzzer you can disable the buzzer the symbol displayed or select one of the three types of sound signaling
24. sequence of 16 characters 4 Open the Communication menu select the Configuration item and indicate the computer port to which the controller is connected 5 Open the File menu select New device and then ACU 100 ACU 100 SATEL 39 Control panel Communication Help i Open F3 m amp Save F2 Save as Shift F2 ypads Zones Partitions Outp New device CA5V1 01 Configuration Soe CA6V2 v2 00 v3 03 CA6 v3 04 v4 xx v5 xx CAb6v6 Exit CA10V2 CA10V3 CA10 v 4 0 4 2 CA10 v 4 3 4 5 CA10 v4 6 4 7 Comments Default settings Keyfobs receiver RX RE RXH GSM4 5 LT module ACU 100 Fig 17 Activation of the ACU 100 controller support in the DLOAD10 program 6 Having established communication the program will compare identifiers in computer and controller and if they coincide it will read data from the controller 7 Configure the controller settings 8 After completion of entering the new settings save them in the controller by clicking on the button A useful diagnostic tool in the DLOAD10 program is the level of signal currently received by the controller in its working radio band which is presented as a real time diagram It illustrates both the noise level and all registered at a particular moment signals from other radio devices operating on the same frequency band Presented in red color are signals from wireless devices operated by the controller To
25. system LCD keypad information on low batteries and other troubles is given in the user menu TROUBLES submenu and in the DLOADX program in the Troubles window Note When low battery status is indicated replace the battery within 2 3 weeks Jamming this function available in the LCD keypad connected to the controller makes it possible to check whether the wireless system operation is not jammed by any device which emits radio waves on the same frequency If there was a jamming event information is given of the fact stating how many times and what was its amplitude In the DLOAD10 program all the information on jamming is given in on line mode with no need for calling any function In the INTEGRA INTEGRA Plus or VERSA system LCD keypad the information on possible jamming is given in the user menu TROUBLES submenu and in the DLOADX program in the Troubles window Test mode activation of the test mode makes all the wireless devices indicate communication with the controller by blinking LEDs Detectors inform on violations and tampers using the LEDs In the normal operating mode of the wireless devices the 44 Two way wireless system ABAX ACU 100 signaling on LEDs is off for energy saving considerations When in the test mode the tamper alarm signaling in sirens is disabled After exiting the test mode its actual termination will take place at the next response period The test mode will be automatically exited 30 mi
26. to be CONFIQUIED eee eeeceee eee eennteeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeneeaaaes 23 7 Sirens in ABAX i med 24 7 1 Description of ASP 105 siren functioning eees eeeeeeeee aaa oe ewa wawa nennen ennt tnn 24 7 2 Description of ASP 205 siren functioning e eeeeeaae eee aaa aaa aaa a nicinnia 25 7 3 Additional siren parameters to be configured eeeee eee eee aaa aaa aaa aaa eenniwia 25 8 ASW 100 230V AC wireless controllers in ABAX system 2 sueeeeaaaaaaa22 26 9 Radio signal level tester in ABAX system sss 26 10 Interaction with alarm control panels cccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaaeeeeeeeeeeeeeeseaes 27 10 1 Expander of wireless devices INTEGRA INTEGRA Plus cccccccccceeceeeceeeeeeeeeeeeeaeeees 27 10 2 Addressable zone expander CA 64 cccccccccccceccceccceccceeeeeeeeeeceeeeceeceaeceeecesesenaeseaeeeaeenaeeaas 30 10 3 Zone expander CA 10 area day aaa eee odere AO A oa ci 31 10 4 Module of wireless devices any alarm control panel aeeaa aaa aaa aaa aaa aa aa aa aaaaaaaea 33 11 Programming and dIagnoSUGSN eerte ette A Z AE te ee ertt eren 35 11 1 LCD keypad of INTEGRA INTEGRA Plus security system seeeeee 35 11 2 LCD keypad of VERSA alarm system ssssssssssseeeeeeseeeeeee mene enne nennen nennen 35 rs ero Moles rin na RE
27. to connect any external detector of NC type e remote configuration of parameters e tamper contact e power supply lithium battery CR123A 3V 3 7 AMD 101 DUAL CHANNEL WIRELESS MAGNETIC DETECTOR e two reed switches e individually identifiable input to connect any external detector of NC type e remote configuration of parameters e tamper contact e power supply lithium battery CR123A 3V 3 8 AMD 102 WIRELESS MAGNETIC CONTACT WITH INPUT FOR ROLLER SHUTTER DETECTOR e two reed switches e individually identified input for connecting a roller shutter detector or NC type detector e remote configuration of parameters e tamper contact e power supply lithium battery CR123A 3V ACU 100 SATEL 11 3 9 AMD 103 WIRELESS MAGNETIC CONTACT one reed switch tamper contact power supply lithium battery CR2477N 3 V 3 10 AGD 100 WIRELESS GLASS BREAK DETECTOR detection of breaking plate laminated or tempered glass multi frequency digital signal analysis detection sensitivity adjustment remote configuration tamper contact power supply lithium battery CR123A 3V 3 11 AFD 100 WIRELESS WATER FLOOD DETECTOR external sensor tamper contact power supply lithium battery CR123A 3V 3 12 AVD 100 WIRELESS VIBRATION DETECTOR AND MAGNETIC CONTACT advanced processing of piezoelectric sensor signal vibration detection sensitivity adjustment remote configuration tamper contact power supply lithium battery CR123A 3V 3 13 ASD 10
28. 0 WIRELESS SMOKE AND HEAT DETECTOR optical sensor for visible smoke detection heat sensor which responds to the temperature rising above a predetermined threshold as well as to a high speed of temperature rise sensitivity range selection according to EN54 remote configuration acoustic and optical alarm indication power supply lithium battery CR123A 3V 3 14 ASD 110 WIRELESS SMOKE AND HEAT DETECTOR EN54 7 compliant visible smoke sensor EN54 5 compliant heat sensor acoustic and optical alarm indication test feature tamper contact power supply lithium battery CR123A 3V 12 Two way wireless system ABAX ACU 100 3 15 ARD 100 WIRELESS REORIENTATION DETECTOR e accelerometer to analyze acceleration and gravitation e memorizing the position when switched over to active mode or when test mode is activated e remote configuration of parameters e tamper contact e power supply lithium battery CR123A 3V 3 16 ATD 100 WIRELESS TEMPERATURE DETECTOR e digital temperature sensor e up to two programmable temperature thresholds e remote configuration e tamper contact e power supply lithium battery CR123A 3V Note The ATD 100 detector is only supported by the controller interfacing with the INTEGRA firmware version 1 09 or newer or INTEGRA Plus control panel 3 17 ASP 105 WIRELESS OUTDOOR SIREN e optical and acoustic signaling triggered independently by radio e acoustic signaling piezoelectric transducer e remote
29. 100 detector The 4 and gt keys enable navigation between the programmable parameters The A and V keys make it possible to select sensitivity within the range from 1 to 3 see Table 10 as well as enable disable the pet immunity option Enabled pet immunity option is indicated by the 11 symbol 13 2 2 APMD 150 detector The 4 and gt keys allow you to navigate between the detector programmable parameters and the A and VW keys to modify them The following should be programmed sensitivity of the PIR sensor within the 1 to 4 range 1 minimum 4 maximum sensitivity of the microwave sensor within the 1 to 8 range 1 minimum 8 maximum manner of operation in the test mode O signaling violation after motion is detected by both sensors 1 signaling violation after motion is detected by PIR sensor or 2 signaling violation after motion is detected by MW sensor 13 2 3 AMD 100 and AMD 101 detector Use the A and V keys to select the active reed switch ACU 100 SATEL 49 13 2 4 AMD 102 detector After selecting the first position the first zone occupied by the AMD 102 detector use the A and W keys to indicate the active reed switch After selecting the second position the second zone occupied by the AMD 102 detector the parameters of roller shutter zone can be configured The 4 and gt keys allow you to navigate between the parameters and the A and W keys to modify them The following should be
30. 24s 300 and for 36s 450 Outside the response period information on tampers of the devices and violations of the detectors being in their active state is sent to the controller Note In the case of the AMD 103 detector no communication takes place during polling Filter it is possible to define the number of unanswered polls after which no communication will be reported You may enter the values from the range of O to 50 Entering the digit O will disable control of the device for presence in the system Higher sensitivity for jamming detection if this option is enabled the sensitivity of detection of radio communication jamming is boosted The option is available when the controller is connected to the INTEGRA INTEGRA Plus or VERSA control panel Note In the case of the AMD 103 magnetic contact the presence check is performed in a different way than for the other ABAX system devices If the value programmed for the FILTER parameter differs from 0 the lack of presence will be reported if no transmission from the AMD 103 magnetic contact is received within one hour Configuration some wireless devices e g APD 100 APMD 150 AGD 100 AVD 100 and ASD 100 detectors ASP 105 and ASP 205 sirens make extra options available which can be configured by radio Problem signaling activation of any of the controller functional outputs TPR CON JAM or LBA can be indicated by LED or sound signal This option is unavaila
31. 47 13 19 AT DS100 detector coz ai Ovni ai OE usu p Asc 47 13 1E10ASPETOS SIFEM E PEE RP RR NANA tai iut neue 47 13 1 AS P2205 SEN ed retos A AR A mem AT EEE 47 13 1 12 ASW 100 E and ASW 100 F controllers eee erent EKNE aaa aaa aaa mener 48 13 2 LCD Key AG oar aoi C E 48 13 2 1 4APD100 det amp ctOt x i rtt did sec ya Ee RD oq nti et t pen ro da eint 48 Toz APMD 150 detector certe b Opa EROR PR rip Ee BOR ERR doda PGE EAE 48 13 2 3 AMD 100 and AMD 101 detector een eee EAE 48 13 2 4 4 AMD 102 OC Cte ClO lies im oett petto decreuit e tbc abend dion bO a flute sra reri ad 49 13 29 AGDE100 detector 5o mette detta ean iesu Talente na E fiut ette ida 49 19 210 4AVDS100 deteClOL zee oi too nene ped adopte eg tbc tbt ea en obo iun sos reus ed 49 19 254 AoD 100 detectol ibt mete ea nb metta eda ice Ee mod Miata 49 19 2 9 ARDETOQ detector nett pete ndr petet a edge toda te ios eae a funi rete 49 13 2 9 VAT D 4 00 detectors ober meo Pe bt metre te ed n ALE eibi Bod n d iuf sioe niet 49 13 210 AS P2105 SILEN eee reine ia UO vacate tee ERR ni Rn EPI OBEN Sete ss tedesca ep eb tenu eese si dae at 49 13 2 T T ASP 205 SITO ot ctr a ya f RIA Trini te mU dum oda Do A se e p 50 13 2 12 ASW 100 E and ASW 100 F controllers ssseeeee ene enm enne 50 14 Restoring controller default settings c eee eee ee aaa aaa aaa aaa aka saN AAA 50 15 SPCCIICALON
32. ABAX SYSTEM The sirens sent information on tampers and storage battery power supply status to the ACU 100 controller The information on tampers is sent immediately while all the other information at the response time see RESPONSE PERIOD Note Signaling of the tamper alarm is blocked on entering the test mode on entering the service mode if working in conjunction with the INTEGRA INTEGRA Plus or VERSA control panels for 40 seconds after power up of the siren The command to block unblock the tamper alarm signaling in connection with entering exiting the service mode or the test mode is sent during polling time Depending on the controller operating configuration the signaling is triggered on activating the output of INTEGRA INTEGRA Plus or VERSA system to which the wireless siren is assigned The output is to be suitably programmed on activating the controller input which has been selected as the control one 7 1 DESCRIPTION OF ASP 105 SIREN FUNCTIONING The ASP 105 outdoor siren occupies 2 positions on the list of devices supported by the controller acoustic signaling and optical signaling separately takes up 2 outputs and 2 zones in the INTEGRA INTEGRA Plus or VERSA alarm system takes up 2 zones and also requires 2 controller inputs to control signaling in the CA 64 or CA 10 alarm system requires 2 inputs and 2 controller outputs when working in conjunction with other contr
33. NTEGRA PLUS SECURITY SYSTEM 1 Enter the service code confirm with the key and press the key 9 to get access to the service mode 2 Proceed to the function of programming the controller settings a STRUCTURE gt HARDWARE EXPANDERS SETTINGS gt controller name 3 Program the controller as required 4 Quit the service mode Functions for programming the controller and wireless devices No autorst 3t Tamper in part Response period High jam sens New device Use ARU 100 Active mode Configuration Filter Remove device Synchronization Test mode on Test mode off Diagnostics of the controller and the wireless devices registered in it is facilitated by using functions available in the user menu Overview of all functions see Section DESCRIPTION OF FUNCTIONS OPTIONS AND COMMANDS 11 2 LCD KEYPAD OF VERSA ALARM SYSTEM In order to select the partition in which tamper alarm will be triggered if the controller is tampered or disconnected from the bus and or to program the response period and name you can use the SETTINGS function SERVICE MODE 2 HARDWARE 1 KPDS amp EXPS 36 Two way wireless system ABAX ACU 100 b 2 SETTINGS After selecting the controller from the list to be displayed the programming should be conducted according to the step by step method The other programming related functions of the ABAX system are available in the ACU 100 submenu SERVICE MODE 2 HARDWARE 1 KPDS amp EXPS 3 ACU 100
34. Normally if 3 consecutive tamper alarms are not cleared signaling of next tamper alarms will be blocked which prevents the same events being repeatedly saved in the control panel memory The option allows the blocking to be disabled Always active this option available when interacting with the INTEGRA INTEGRA Plus or VERSA series control panel allows the detector to be permanently switched to active state ACU 100 SATEL 45 Service end this function ends the service mode in the keypad 12 RETRANSMISSION If the ARU 100 repeater is registered in the controller you can define which wireless devices are to communicate with the controller via the repeater Depending on the alarm control panel to which the controller is connected you can do so using e INTEGRA INTEGRA Plus with firmware version 1 12 or newer DLOADX program version 1 12 or newer or keypad connected to the control panel e another control panel DLOAD10 program version 1 00 041 or newer 12 1 DLOADX DLOAD10 PROGRAM In the ARU column e leave the field blank if the device is to communicate directly to the controller e enter the ARU 100 repeater number in the list of wireless devices if the device is to communicate to the controller via the repeater the ARU 100 repeater takes up two positions on the list of devices enter the number of the first of them 12 2 KEYPAD CONNECTED TO THE CONTROL PANEL 1 Run the Use ARU 100 function SERVICE
35. P switches a inean aaa aae Ee E E E AEREE I RE AE E E a A EEE 6 2 9 GOMUOMPUS eser i di T E A EE AT 7 4 Outputs dee E t dtt E E E EO A 8 2 5 Fu cti nal 0UtDUtS ine e A PG ER RR rn ke RR d id e A EEE R E Ani 8 3 Wireless devices interfacing with the controller cccccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 9 3 1 ACX 100 Input 8 output expansion module cece eee eee eee aaa aaa aaa nenene 9 3 2 ACX 200 Hardwired zone output expander eeeeeeee eee aaa aaa aaa aaa aaa aaa aaa aaa aa aaa ae 9 3 3 ACX 201 Hardwired zone output expander with power supply sss 9 3 4 APD 100 Wireless passive infrared detector e eeeeee eee aaa aaa 10 3 5 APMD 150 Wireless dual motion detector sss 10 3 6 AMD 100 Wireless magnetic detector 24 2 44 eeees ea on eee a anawa aaa dia aka inni 10 3 7 AMD 101 Dual channel wireless magnetic detector eeee eee aaa aaa aaa aaaaaa ae 10 3 8 AMD 102 Wireless magnetic contact with input for roller shutter detector 10 3 9 AMD 103 Wireless magnetic contact 2 6 cccceesecceeccceeteeeeteeeecboeeeneeeetedseeedsnesdeeerseeeenesenneeeees 11 3 10 AGD 100 Wireless glass break detector eeeeesses eene tenens 11 3 11 AFD 100 Wireless water flood detector sss 11 3 12 AVD 100 Wireless vibration detector
36. R T QE EE 36 11 4 LCD keypad connected fo controller ee AO A e it Pine Dae erra siccus 37 11 4 1 Service mode of keypad connected to the controller ssse 37 11 5 Dload10 progra m 38 11 6 Description of functions options and commanQS e seea aaa aaa aaa aaa aa aaa aaa aaa aaa aa aanaaanaaenaa 41 12 Reran MI SIOM 6st eost tet t GR CC E 45 12 1 DloadX 7 Bload10 brogram aaa er rent a orte ett Rt alae RA HR Ra x opt eaa ug 45 12 2 Keypad connected to the control panel cccccccccceccceeeececeeeeeeeeeeeeeeeceeeceeeceeaeceaeesaeseaeesaeenas 45 13 Configuration of additional parameters and options in wireless devices 45 13 1 DloadX or Dload 10 program ua o re atr SR IER SUR ce E e ob n pce ki be era ra us 45 Tatt APD 100 detectorz ui itte tt a e ed at a RO RR ER coded reu agir 45 13 1 2 APMD3150 d6lteClOF a EA ee e RADI te eai ese E M A 46 13 1 3 AMD 100 and AMD 101 detectors ee eee aaa aaa aaa aaa aaa aaa nnne enne 46 13 1 4 AMB 102 detector iit o WEKA ak OE aaa A e In KD ERO ak 46 13 1 5 2AGD 190 deteGltor 4 nino Rte PRIOR ieee a van cab X dE aa FRE CA d en ER rec pe RR 46 13 1 6 2AVD 100 detectOr nim DR ERR RR PERRO ERES E GA ERR EM T ER cp uo red 46 13 14 ASD 100 detector eim Re AO Dex e O AAA A DA DI dea 46 13 126 ARO 100 Gd6teCtor ine er ERR GR RP RERO ERES EX ERR DU ERR e erect oda
37. S ax cncicattcactenteredeat e A E a a E R AEEA 50 16 History of the manual updeles aaa a a i a aa 51 4 Two way wireless system ABAX ACU 100 1 GENERAL The ACU 100 controller allows communication between any alarm control panel and the ABAX system wireless devices It enables wire operated security systems to be expanded by addition of wireless devices The ABAX system is based on two way communication All messages sent by the devices are acknowledged which ensures that the equipment status information will reach the controller and allows online check of the devices for their presence in the system Configuration of parameters and testing of the wireless devices is performed by radio without the need to dismantle their housings Coded communication between the units takes place within the frequency band of 868 0 MHz 868 6 MHz 2 DESCRIPTION OF ACU 100 WIRELESS SYSTEM CONTROLLER The ACU 100 controller supervises and coordinates operation of up to 48 wireless devices The status of devices is signaled on the OC type outputs It can also be transmitted to the control panel through the communication bus The controller settings and wireless equipment parameters are programmed by means of an LCD keypad or a PC computer 2 1 ELECTRONICS BOARD NI NOS diil dL diAL Ac NOJ A R5485 B CLK DAT COM 0O 2222222222222229 TPR CON JAM LBA OUT1 OUT2 OUT3 OUT4 OUTS OUT6
38. VERSA control panels the detector operating mode is controlled through the communication bus Arming the partition to which the zone with wireless detector belongs will switch the detector into the active mode while disarming will switch the detector into the passive mode In the other configurations the detector operating mode is controlled by means of the controller inputs Indicate for each detector the input that will control the detector operation Connect a suitably programmed control panel output to the input Activating the controller input will switch the detector into the active mode The detectors are switched over from the passive state to the active state and vice versa during the response time hence performance of this operation is delayed in relation to the moment of switchover command This delay depending on the chosen response frequency can be up to 12 24 or 36 seconds The RESPONSE PERIOD has an effect on the detector energy consumption level The battery use by the detector decreases as the frequency of communication between the controller and the wireless device lowers It is advisable in some situations that the detector be always active For example the user wants to be sure that no window is open in the facility at the moment of arming Switching over the window protection magnetic detector permanently in active state allows to avoid the risk that the window will be opened just before arming but the information abou
39. ased by connecting the ACX 100 expansion modules to the controller The maximum number of outputs 48 controller 5 ACX 100 modules The output activates after receiving suitable information from a wireless device assigned to it the information depending on the device type e the wireless detectors signal violations the ASP 105 siren inform of a discharged battery and a failure of 12 V DC external power supply e the ASP 205 sirens inform of battery discharge e the ACX 200 and ACX 201 expanders signal zone violation e the ASW 100 E and ASW 100 F controllers inform that the button was depressed in Mode 0 or the electric circuit was closed in Mode 1 and 2 The outputs can be programmed as NO normally open or NC normally shorted to ground All the outputs of the controller and the ACX 100 modules connected to it are being programmed at the same time Depending on how the outputs have been programmed activation of the output is indicated as follows LED assigned to the output comes ON outputs programmed as the NO type LED assigned to the output comes OFF outputs programmed as the NC type The outputs can be connected to the control panel zones FUNCTIONAL OUTPUTS 2 5 ZN If the controller is working as an expander with the INTEGRA INTEGRA Plus or VERSA control panels you are not required to know how the functional outputs operate because they need not be connected to the control panel all information will
40. ating the detectors in relation to arming The output programmed as the ARM STATUS will only get active after expiry of the exit time However some control panels allow you to choose another function which activates the output immediately after arming command is given to the control panel For example the output can be programmed in the CA 10 as type 35 POWER SUPPLY ON ARMED MODE and in the CA 64 as type 42 POWER SUPPLY IN ARMED STATE The delay effect in activating the detectors as against the arming can only be avoided when the exit time exceeds the RESPONSE PERIOD When controlling the detectors the input of the controller can also be programmed as always active In this case the detectors will remain permanently in active state In order to control the operation of sirens you should connect the control panel alarm signaling output to the controller input Activating the control panel output will trigger the siren 2 4 OUTPUTS ZN If the controller is working as an expander with the INTEGRA INTEGRA Plus VERSA or CA 64 control panels you are not required to know how the outputs operate because they need not be connected to the control panel information from wireless devices will be sent to the control panel via communication bus The PCB of the ACU 100 controller incorporates eight OC type outputs to which wireless devices are assigned Any number of wireless devices can be assigned to one output The number of outputs can be incre
41. be sent to the control panel via communication bus ACU 100 SATEL 9 The ACU 100 controller PCB incorporates four OC type outputs to signal TPR wireless device tampers lack of communication with ACX 100 modules and also controller tampers provided the TMP terminals are connected to the controller tamper circuit CON lack of communication with wireless devices JAM jamming the radio signal for the ABAX system to the degree which makes communication impossible LBA problems with power supply of a wireless device low battery discharged storage battery or loss of external power supply If the ACX 201 expander is registered in the controller overload of the expander AUX1 AUX2 supply outputs is additionally signaled at this output Depending on how the outputs have been programmed see OUTPUTS activation of the functional output is indicated as follows LED assigned to the output comes ON outputs programmed as the NO type LED assigned to the output comes OFF outputs programmed as the NC type After connecting the functional outputs to properly programmed zones of the control panel zone type function etc the control panel may signal occurrence of some problems in the ABAX system The problems can be diagnosed by means of LCD keypad or computer connected to the controller Connecting the TPR output to the CA 64 control panel is unnecessary since information on tampers of wireless devices is transmi
42. ble when the controller interacts with INTEGRA INTEGRA Plus or VERSA series control panels Input types the control inputs can be programmed as NO normally open or NC normally closed The parameter is not available if the controller is connected to the INTEGRA INTEGRA Plus or VERSA series control panels ACU 100 SATEL 43 Output type outputs of the controller and ACX 100 modules can be programmed as NO normally open or NC normally closed The parameter is not available if the controller is connected to the INTEGRA INTEGRA Plus or VERSA series control panels Set defaults this function which is only available in the LCD keypad connected to the controller is used to restore the defaults TESTS calls submenu of the keypad connected to the computer Signal level this function available in the LCD keypad allows checking the level of signal received from wireless devices The signal level is presented in percentage form In the DLOAD10 program the signal level is visualized graphically in on line mode with no need for calling any function In the DLOADX program information on the signal level is shown in the Wireless device window Communication state this function available in the LCD keypad connected to the controller allows you to check with which devices the communication is correct or non existent or was temporarily lost In the DLOAD10 program all the communication related information is sh
43. c contact which of the two reed switches on the electronics board is to be active Program the following for the vibration detector sensitivity a single vibration meeting the sensitivity criterion will cause violation of the detector number of pulses Registering the predefined number of vibrations within 30 seconds will cause violation of the detector All vibrations count they do not have to meet the sensitivity criterion For the value 0 the pulses are not counted Note Parameters are being independently analyzed As a result the detector can signal violation after registering a strong single vibration caused by a powerful impact as well as after a few slight vibrations caused by a series of weak strikes ASD 100 wireless smoke and heat detector The following is to be programmed operating mode of the heat sensor operating mode of the buzzer duration of alarm signaling by buzzer LED ARD 100 wireless reorientation detector Sensitivity is to be programmed 24 Two way wireless system ABAX ACU 100 ATD 100 wireless temperature detector For each position taken by the detector preset the following temperature threshold parameters threshold type high the detector will report violation when the temperature rises above the defined value or low the detector will report violation when the temperature drops below the defined value temperature tolerance 7 SIRENS IN
44. can be assigned will be displayed Using the Y and A keys select one of them and press the key press the key to terminate the new device adding procedure If the device takes more than one position on the list of devices additional zones following the selected one will be automatically assigned to the device 7 A message will be displayed to inform that the expander identification function has been started 8 After identification of the devices the keypad will display a suggested name for the zone to which the device is assigned The name can be changed The name will also be assigned to the output if the device is to be assigned to the output Press the key to save the new name Press the key to terminate the name giving procedure the zone will then be given a name consisting of the name and serial number of the device If the device occupies more than one zone this procedure is repeated for each zone 4 6 REMOVAL OF WIRELESS DEVICES Note The procedure of removing wireless devices for the controller operating with the VERSA control panel is described in the installer manual of the control panel 4 6 1 Dtoap10 and DLoADX programs In order to remove a wireless device from the system do the following 1 Click on the device you want to be removed 2 Press the Remove device button 3 Following the displayed instruction press the Yes button to confirm your intention to remove the device The device will be remo
45. can elapse from the moment the new settings are programmed to the moment they are actually saved in the expander if the response period is 36 seconds The settings of expander zones are stored in non volatile memory hence the loss of power supply will not mean any loss of preprogrammed settings Note If the communication with the ACU 100 controller is lost all of the previously activated outputs will enter the inactive state after 20 response periods Additionally the ACX 201 expander will transmit information on status of AUX1 AUX2 supply outputs overload information is sent when the AUX1 or AUX2 output load exceeds 0 5 A battery status battery discharge information is sent when the battery voltage drops below 11 V for longer than 12 minutes 3 battery tests This information will be sent to the controller until the battery voltage rises above 11 V for longer than 12 minutes 3 battery tests AC supply status power supply loss information is sent when the AC supply loss is lasting longer than 30 seconds Power restore is reported with the same delay When working in conjunction with the INTEGRA INTEGRA Plus or VERSA control panel information on these troubles is sent through the communication bus The troubles can be viewed by means of the keypad or DLOADX or GUARDX program When working with other control panels information on these troubles is transmitted through the LBA function output In order to
46. cation with the control panel green blinking light correct communication with the control panel e interaction with other alarm control panels green steady light normal operation of the controller green blinking light synchronization in the process alternate green and red blinking light occurrence of one of the problems signaled on functional outputs see FUNCTIONAL OUTPUTS LED indicators of output status Description of terminals COM common ground 12V power supply input TMP controller tamper terminals NC You can use the TMP terminals in two ways e connect the terminals to the tamper circuit of the control panel e connect one of the TMP terminals to the ITMP tamper circuit input and the other to the COM ground terminal information of the controller tamper will be fed to the TPR output and to the communication bus ITMP input for connecting controller tamper circuit Note If the TMP terminals are not connected to the controller tamper circuit the ITMP terminal must be shorted to the common ground TPR information output tampers CON information output no radio communication with wireless devices JAM information output radio jamming LBA information output problems with wireless devices power supply or with supply output overload in the ACX 201 expander OUT1 0UT8 information output wireless equipment status AR1 AR4 control inpu
47. ces Having connected the ACU 100 controller to the control panel start the expander identification function in it ACU 100 SATEL 31 CA 64 LEE DOOOO0220200000000000000090920 K1 COM EX2 DT2 CK2 Ji z2 23 COM Z4 Z5 COM Z6 27 COM Z8 Z9 COM Z10 Zi COM Z12 Z13 COM Z 4 Z15 COM Z16 ACU 100 CZ Q T N La lal lt JSTTTOOOOTP OO O TPR CON JAM LBA OUT1OUT2 OUT3 OUT4 OUTS OUT6 OUT OUTS ART AR A AR2 NL O9 dWLI dWL dL AZl WOO 2 2 2 e 2 4 W Fig 10 Example of connecting the ACU 100 controller to the CA 64 control panel When interacting with the CA 64 control panel the ACU 100 controller makes 48 wireless zones available to it The zone numbers are assigned to the wireless devices registered in the controller according to the following principle zone number 16 number of the wireless device on the list The system zones to which wireless devices are assigned can be programmed as NC NO or EOL depending on the type of device the zone will provide information about detector violation power failure etc 2EOL NC or 2bEOL NO depending on the type of device the zone will provide information about detector violation power failure etc and additionally about tampers Connection of the controller to the CA 64 alarm control panel excludes the possibility to connect to it the zone expanders CA 64 E CA 64 EPS and CA 64 ADR as wel
48. configuration of acoustic signaling e optical signaling LED indicators e tamper contact e power supply direct voltage 12 V 15 e emergency power supply 6 V 1 2 Ah battery 3 18 ASP 205 WIRELESS INDOOR SIREN e acoustic signaling piezoelectric transducer e optical signaling LED indicators e remote configuration of 2 signaling modes e tamper contact e power supply lithium battery CR123A 3V 3 19 APT 100 BIDIRECTIONAL KEYFOB e controls the INTEGRA INTEGRA Plus or VERSA alarm system e 5 buttons for starting up to 6 selected functions e 3LEDs to indicate the alarm system status e sound signaling of keypress and transmission reception acknowledgement e power supply CR2032 3V lithium battery Note The APT 100 keyfob is only supported by the controller interacting with the INTEGRA version 1 06 or newer INTEGRA Plus or VERSA version 1 01 or newer control panels Description of how the keyfobs should be added to the users or configured please see the user manuals for respective control panels ACU 100 SATEL 13 3 20 ASW 100 E 230 V AC WIRELESS CONTROLLER e remote switch ON switch OFF of devices to be connected to 230 V sockets e type of controller socket E e button for manual control of 230 V electric circuit e LED indicator of controller status e power supply 230 V AC 3 21 ASW 100 F 230 V AC WIRELESS CONTROLLER e remote switch ON OFF of devices to be connected to 230 V sockets e type of controller soc
49. controllers Enter a digit from the O to 2 range which corresponds to the selected mode of operation 13 2 LCD KEYPAD In the LCD keypad of INTEGRA INTEGRA Plus system additional parameters and options of the wireless devices are to be programmed by means of the CONFIGURATION function SERVICE MODE STRUCTURE HARDWARE EXPANDERS SETTINGS gt controller name gt CONFIGURATION Having started the function select the zone to which the wireless device is assigned and press the or key In case of devices which take up more zones selection of the suitable zone depends additionally on the parameter to be programmed Having programmed the parameters confirm the new settings with the key Automatic return to the zone selection list will follow In the LCD keypad connected to the controller additional parameters and options of the wireless devices are also programmed by means of the CONFIGURATION function SERVICE MODE SETTINGS CONFIGURATION Having started the function select the device form the list and press or b In case of devices which take up more zones selection of the suitable zone depends additionally on the parameter to be programmed Having programmed the parameters confirm the new settings with the key Automatic return to the device selection list will follow Configuration of the wireless devices by means of the LCD keypad of VERSA system is described in the programming manual for VERSA control panels 13 2 1 APD
50. d be enabled APMD 150 wireless dual motion detector The following is to be programmed sensitivity of PIR sensor sensitivity of microwave sensor test mode operation AMD 100 and AMD 101 wireless magnetic detectors with an additional input For the detectors with electronics version 3 5 D or newer you must specify which of the two reed switches on the electronics board is to be active in older detectors the selection is made by means of a jumper In case of the AMD 101 detector which occupies 2 positions on the list of devices 2 zones in the system the reed switch is to be selected for the first position first zone AMD 102 wireless magnetic contact with input for roller shutter detector For the magnetic contact you must specify which of the two reed switches on the electronics board is to be active For the roller shutter input you must program the following number of pulses the registration of which will cause violation of the input pulse validity the time counted from the pulse occurrence during which next pulses must occur for the input to become violated Note The counter of pulses is reset after the pulse validity time expires and after switching the detector over from passive into active mode AGD 100 wireless glass break detector Sensitivity of the high frequency channel is to be programmed AVD 100 wireless vibration detector and magnetic contact Determine for the magneti
51. e The program will not establish communication with the controller unless a valid identifier is entered If data of the system we wish to get access to were previously saved in the computer a window will be displayed on the screen with a list of files containing data with consistent identifier You can choose one of these files to establish communication Service code the keypad code password is intended for protection of the controller against an attempt of unauthorized reprogramming By default it has the form of 12345 but it can be changed to any sequence of 8 digits Without entering the correct code the controller service mode cannot be started in the keypad New device this command initiates the procedure of adding new wireless devices to the system Remove device this command initiates the procedure of deleting wireless devices from the system Device names you can assign names to the wireless devices registered in the controller This does not apply to the controller operating together with INTEGRA INTEGRA Plus or VERSA series control panels Serial numbers this service function in LCD keypad connected to the controller makes it possible to check the serial numbers of wireless devices included in the system The serial number in DLOADX and DLOAD10 programs is displayed in on line mode at each device registered in the controller 42 Two way wireless system ABAX ACU 100 Inputs you should select a control
52. e controller outputs OUT1 to OUTS are connected respectively to the control panel zones Z1 to Z5 preprogrammed as type NO The TPR output which informs of tampers of wireless devices and controller TMP terminals connected to COM and ITMP terminals is connected to the Z6 panel zone preprogrammed as NO type reaction type 24H AUDIBLE The OUT4 panel low current output has been programmed as type 35 POWER SUPPLY ON ARMED MODE and connected to the AR1 controller control input This input toggles the wireless detectors between the passive and active state The OUTS5 panel low current output has been programmed as type BURGLARY ALARM ACU 100 SATEL 35 SIGNALING and connected to the AR2 controller control input This input triggers the wireless siren 11 PROGRAMMING AND DIAGNOSTICS The way of programming and the access to diagnostic functions depend on the working configuration of the controller e interacting with INTEGRA INTEGRA Plus or VERSA control panels keypad of alarm system in service mode computer with DLOADX program connected to INTEGRA control panel computer with DLOAD10 program connected to the RS 232 port of the controller for the duration of diagnostic test e interacting with other control panels LCD keypad to be connected to the controller for the time of programming computer with DLOAD10 program connected to controller RS 232 port for the time of programming 11 1 LCD KEYPAD or INTEGRA I
53. e threshold or L low temperature threshold numerical value corresponding to a temperature from the 30 C to 70 C range with up to 0 5 accuracy numerical value corresponding to a tolerance from the 0 5 C to 10 C range with up to 0 5 accuracy 13 1 10 ASP 105 siren Program the acoustic signaling parameters the first position the first zone to which the siren is assigned i e enter the two digit sequence according to Table 12 1st digit 2nd digit acoustic signaling digit signaling duration sound type 1 1 minute sound type 2 3 minutes sound type 3 6 minutes sound type 4 9 minutes Table 12 For example entering the values 2 3 means that acoustic signaling type 2 has been selected and that its duration will be 6 minutes 13 1 11 ASP 205 siren Determine the signaling parameters independently for both positions zones occupied by the siren entering in each case a 3 digit sequence according to Table 13 48 Two way wireless system ABAX ACU 100 1st digit 2nd digit 3rd digit digit signaling duration digit acoustic signaling optical signaling 1 minute none disabled 3 minutes sound type 1 enabled 6 minutes sound type 2 9 minutes sound type 3 Table 13 For example entering the values 2 0 1 means that the signaling will last 3 minutes the acoustic signaling has been disabled and the optical signaling enabled 13 1 12 ASW 100 E and ASW 100 F
54. ed by the procedure of expander identification in the control panel 4 5 2 LCD keypad connected to the controller In order to add a new wireless device to the system do the following 1 Start the NEW DEVICE function 2 Enter the 7 digit serial number of the device to be added and press the key The serial number can be found on the electronics board or on the housing Each radio signal level tester has the serial number 0000500 3 Depending on which device is to be added to the system turn on power supply of the ACX 200 or ACX 201 expander turn on the ARF 100 tester plug the ASW 100 E ASW 100 F wireless controller into the 230 V socket install the battery in ASD 100 detector violate open the tamper contact in case of the other devices If the entered serial number is inconsistent with that of the device being added or the device with such serial number has already been registered a suitable message will be displayed and automatic return to the main menu will follow 4 A message will confirm addition of the new device with the serial number shown on the display Press the key to finish the procedure of adding the new device You can cancel the new device addition by pressing the key 4 5 3 LCD keypad of INTEGRA INTEGRA Plus alarm system In order to add a new wireless device to the system do the following 1 Start the function NEW DEVICE SERVICE MODE STRUCTURE HARDWARE EXPANDERS SETTINGS gt co
55. elected sensitivity for the high frequency channel see Table 10 13 1 6 AVD 100 detector For the magnetic contact the first position the first zone occupied by the AVD 100 detector enter the digit O the lower reed switch or 1 the side reed switch to select which of the two reed switches is to be active For the vibration detector the second zone occupied by the AVD 100 detector enter a 2 digit sequence 1 digit sensitivity from 1 to 8 1 minimum 8 maximum 2 digit number of pulses from 0 to 7 For example entering the values 4 6 means that sensitivity has been set to 4 and the number of pulses to 6 13 1 7 ASD 100 detector Enter a 3 digit sequence corresponding to the selected parameters as shown in Table 11 ACU 100 SATEL 47 1st digit 2nd digit 3rd digit digit heat sensor igi audible signaling digit signaling duration disabled none 1 minute A1 sound type 1 3 minutes A2 sound type 2 6 minutes B sound type 3 9 minutes Table 11 For example entering the 0 2 4 means that the heat sensor has been disabled acoustic signaling type 2 has been selected and the signaling by means of buzzer LEDs will last 9 minutes 13 1 8 ARD 100 detector Enter a digit from the 1 to 16 range corresponding to the selected sensitivity 1 minimum 16 maximum 13 1 9 ATD 100 detector For each position taken by the detector enter in turn letter H high temperatur
56. electronics board or on the housing Each ARF 100 tester has the serial number 0000500 3 Depending on which device is to be added to the system turn on power supply of the ACX 200 or ACX 201 expander turn on the ARF 100 tester plug the ASW 100 E ASW 100 F wireless controller into the 230 V socket install the battery in ASD 100 detector violate open the tamper contact in case of the other devices If an invalid serial number has been entered you will be informed of it by a suitable message Then you should enter the correct serial number and repeat the above mentioned step 4 A confirmation message will be displayed that a new device has been added In case of the DLOADX program version 1 09 or newer suggested name for the zone output assigned to the device will appear the name is editable you can select for some devices whether it take one or two positions in the list of devices INTEGRA firmware version 1 09 or newer INTEGRA Plus 18 Two way wireless system ABAX ACU 100 5 Click your mouse on the OK button to finish the procedure of new device addition You can cancel addition of the new device by pressing the Abort button You can also add a next wireless device by pressing the Next button Note If the ACU 100 controller is connected as an expansion module to the CA 64 INTEGRA or INTEGRA Plus control panel the procedure of adding new wireless devices to the system must be follow
57. ends on the RESPONSE PERIOD See DESCRIPTION OF FUNCTIONS OPTIONS AND COMMANDS and can vary from 150 to 450 The higher the response frequency the lower the number of devices that can work within each other s range Recommendations for installation of particular wireless devices can be found in the manuals delivered with respective devices 4 1 INSTALLATION OF ACU 100 WIRELESS SYSTEM CONTROLLER The ACU 100 controller should be installed indoors in spaces with normal air humidity Its electronics board is mounted in the OPU 1 A plastic housing Before fastening the controller to the wall make inlets outlets in the rear wall of the housing for cables to connect the controller to the control panel or ACX 100 expansion modules Caution The cables should not be laid in the close vicinity of the antenna as this may cause radio communication interference Temporary connection of LCD keypad or computer is required for programming or diagnosing the controller if it not operates together with the INTEGRA INTEGRA Plus or VERSA control panels 4 2 CONNECTING LCD KEYPAD TO THE CONTROLLER The LCD keypad must be connected to the RJ socket with four wire cable Connection of the keypad communication bus to the RJ socket is shown in Fig 3 1 KPD 2 CKM 3 DTM 4 COM Fig 3 Sequence of wires in the plug connecting LCD keypad with controller 1 view of plug in the socket 2 view of plug from the pins side Address of the ke
58. er it turns out that further addresses are needed but they are occupied by other devices correct completion of the expander identification procedure will be impossible Then it will be necessary to change the addresses of devices connected to the expander bus The system zones to which wireless devices are assigned can be programmed as NC NO or EOL depending on the type of device the zone will provide information about detector violation power failure etc 2EOL NC or 2bEOL NO depending on the type of device the zone will provide information about detector violation power failure etc and additionally about tampers Changing the wireless detectors from passive to active state takes place simultaneously with arming the partition to which the zone with wireless detector belongs After disarming the detectors will re enter the passive state It does not refer to the 24hr zones The wireless detectors assigned to those zones remain always in the active state Additionally the ALWAYS ACTIVE option can be enabled for any wireless detector A Do not program reversed polarity for the alarm system outputs to which wireless devices are assigned because these devices will function in reversed mode the inactive output will arm and the active output will disarm 10 2 ADDRESSABLE ZONE EXPANDER CA 64 Using the DIP switches set the suitable operating mode address and programming mode of the ACU 100 controller Communicati
59. f keypad connected to the controller You can move through the menu and use the service functions by means of the following keypad keys A scroll the functions list up v scroll the functions list down enter the function submenu 38 Two way wireless system ABAX ACU 100 or exit the function submenu without making changes some functions can only be quitted by pressing the asterisk key H enter the function submenu accept the data entered The menu of service mode in LCD keypad connected to the controller Service end New device Remove device Device names Serial number Inputs Outputs Settings Response period Filter Configuration Trouble indication Input types Output type Set defaults Tests Signal level Communications state Tamper state Battery state Jamming Test mode Clear memory Synchronization Supply voltage Service code Overview of all functions see Section DESCRIPTION OF FUNCTIONS OPTIONS AND COMMANDS 11 5 DLoap10 PROGRAM 1 Set the option of programming through the RS 232 port on the DIP switches on the controller electronics board this is not required when the controller is used in conjunction with INTEGRA or INTEGRA Plus control panel 2 Connect computer to the controller see CONNECTING COMPUTER TO THE CONTROLLER 3 Launch the DLOAD10 program in the computer access to the program is protected with password which is 1234 by default and can be changed to any
60. ic circuit activates the alarm system zone ACU 100 controller output When configuring the ASW 100 E or ASW 100 F controller carefully select the FILTER value i e the number of response periods with no response after which loss of communication with the ASW 100 controller will be reported The 230 V sockets are installed at low position hence the ASW 100 controllers mounted in them are exposed to the risk of being covered by personnel moving around the premises 9 RADIO SIGNAL LEVEL TESTER IN ABAX SYSTEM The ARF 100 tester takes up one position on the list of devices supported by the ACU 100 controller The tester enables checking the level of radio signal received either by the controller from the tester or by the tester from the controller The signal level is displayed on the tester LEDs when the ACU 100 controller is running in the test mode Note Each tester has the serial number 0000500 ACU 100 SATEL 27 In order to check the radio signal level and find the optimum installation position for the wireless device by means of the tester do the following 1 Install battery in the tester 2 Add the tester to the wireless system see ADDING NEW WIRELESS DEVICES If the ACU 100 controller is used in conjunction with the CA 64 INTEGRA INTEGRA Plus or VERSA control panels it is recommended that the ARF 100 tester be added as the last wireless device after the other devices to be installed in the ABAX system This wil
61. input for each wireless device registered in the controller This does not apply to the controller operating together with INTEGRA INTEGRA Plus or VERSA series control panels Notes e When a new wireless device is added to the system the input 1 is indicated by default as the control input e When the entered input number is higher than 24 the input to control the device will be always active Outputs wireless devices are assigned to particular controller outputs This does not apply to the CA 64 it is possible to assign the devices to outputs but the outputs will not be used for communication with the control panel INTEGRA INTEGRA Plus and VERSA control panels Note When a new wireless device is being added to the system it is by default assigned to the output 1 SETTINGS calls submenu of the keypad connected to the computer Response period the controller communicates with the wireless devices at specified time intervals During those periods the controller gathers information on the status of devices and if necessary sends commands to the devices e g switches the detectors to their active passive state activates deactivates the test mode and changes configuration of the devices The response period may be 12 24 or 36 seconds The rarer the communication between the controller and wireless devices the more wireless devices can work within each other s range The maximum number of devices for 12s is 150 for
62. ion modules ssssssssess 16 4 5 Adding new wireless devices teme R RE etude dO AAC PAPAE at KAI 17 4 5 14 DLOAD10 and DLOADX programs sirni saarni iae kaeida a e a ea nnne aaa da aasi enne 17 4 5 2 LCD keypad connected to the controller sssseeene ene eemmmeneennns 18 4 5 33 LCD keypad of INTEGRA alarm system INTEGRA Plus sse eee 18 4 6 Removal of wireless devices sssssssssssss emen aaa entre nennen 19 4 6 1 DLOAD10 and DLOADX programs aaa a a aaa aaa aaa aaa aaa wawa aaa aaa tenni E aaa ana 19 Apa JECD keypad ue nuo enm aite eda tute ire aud 19 5 Hardwired zone output expanders in ABAX system ssssssssssseeeeeee 20 5 1 1 Configuration of ACX 200 or ACX 201 expander zones outputs for ACU 100 controller operation with INTEGRA INTEGRA Plus or VERSA control panel sssseme n 20 5 1 2 Configuration of ACX 200 expander zones outputs for ACU 100 or ACX 201 controller operation with CA 64 control panel eee ea aaa ae aaa aaa aaa aaa aaa aaa st einn nnne 21 5 1 3 Configuration of ACX 200 or ACX 201 expander zones outputs for ACU 100 controller operation with other control panels a aaa a a aaa aaa aaa aaa einn nnne 21 6 Wireless detectors in ABAX system ss eeaaaaa aaa eee aaa aaa aaa aaa nennen nennen 22 ACU 100 SATEL 3 6 1 Additional detector parameters
63. ket F e button for manual control of 230 V electric circuit e LED indicator of controller status e power supply 230 V AC 3 22 ARF 100 RADIO SIGNAL LEVEL TESTER e checking the level of radio signal received by controller from tester or by tester from controller e simulating radio communication of devices to be supplied from battery or external sources e LED indicator showing the radio signal level e buzzer e power supply alkaline battery 9 V GLR61 3 23 ARU 100 RADIO SIGNAL REPEATER e retransmission of signals from 46 wireless devices e LED indicator of the repeater status e tamper contact e power supply 230 V AC Notes e If the controller is connected to a control panel other than INTEGRA or INTEGRA Plus you can only add the ARU 100 repeater using the DLOAD10 program e If the ARU 100 repeater has been registered using the DLOAD10 program in the controller connected to the VERSA control panel the ABAX system should be configured by means of the DLOAD10 program the VERSA control panel does not recognize the ARU 100 repeater and thus you cannot use the DLOADX program or keypad connected to the control panel 4 INSTALLATION A The ABAX two way wireless system should be installed so as to ensure a suitable level of radio signal from devices working together with the controller This will allow the communication problems to be avoided All electrical connections may only be made with power supply disconnected Befo
64. l prevent creating an unnecessary gap due to unused zone after the tester is removed from the system 3 Using the e designated button select the power supply mode for the wireless device which is to be installed and simulated by the tester 4 Start the test mode in the controller During response time the level of radio signal received by the tester from the controller will be displayed on the LED indicator Press the 6 designated button to see the level of signal received by controller from the tester The signal level is always refreshed during the response time which is signaled by 1 short beep If a higher update frequency is required activate the dense polling mode by means of the button The signal level displayed on the LEDs will be refreshed every 2 seconds Information update will be signaled by 2 short beeps Note According to requirements of the EN50131 standard the level of radio signals sent by wireless devices is reduced during the test mode operation 5 Find the optimum location to install the new wireless device 6 Having completed the test switch off the tester and remove it from the ABAX wireless system Note If not used the tester will switch off automatically after 10 minutes 10 INTERACTION WITH ALARM CONTROL PANELS The ACU 100 controller can be used as an expander of wireless devices able to work in conjunction with the INTEGRA INTEGRA Plus or VERSA control panels all information related to the
65. l as the CA 64 PP zones amp outputs expander with power supply 10 3 ZONE EXPANDER CA 10 Using the DIP switches set the suitable operating mode address and programming mode of the ACU 100 controller To determine the operating mode you should take into account the number of keypads installed in the system Depending on the number of keypads the controller makes it possible to expand the system by 2 4 or 6 wireless zones see Table 9 the status of which violations and tampers of the wireless devices assigned to these zones will be transmitted by means of the communication bus 32 Two way wireless system ABAX ACU 100 address 0011 programming DLOAD10 Fig 11 Example of setting the DIP switches operating mode CA 10 control panel with 1 keypad g 2 ot ot XESTE 2 Osgsjo 9 Numbers of additional system zones lots ors zones 9 and 10 are reserved in the system for the 1 keypad zones x sEce js2e o 2285258 EEEHIERE HHHH a oLl8 o88 n C n 11 12 13 14 15 16 output 11 output 12 output 13 output 14 output 15 output 16 1 CLK1 CLK2 in controller in controller in controller in controller in controller in controller 2 CLK1 cLk3 Zone ina zone in 2 output 13 output 14 output 15 output 16 CLK2 keypad keypad in controller in controller in controller in controller SEKI zone in 2 zone in 2 zone in 3 zone in 3 output 15
66. n must be longer than the response time It is recommended that this time correspond to the signaling duration as programmed in the siren Violation of the siren tamper contact will generate tamper alarm which will last 3 minutes sound type 1 and optical signaling Depending on the controller operating configuration the low battery will cause violation of both zones occupied by the siren in the system communication through the bus with INTEGRA INTEGRA Plus VERSA CA 64 or CA 10 control panels activate the controller LBA output activate the controller outputs assigned to both positions occupied by the siren on the list of devices 7 3 ADDITIONAL SIREN PARAMETERS TO BE CONFIGURED ASP 105 wireless triggered outdoor siren The following is to be programmed type of acoustic signaling 26 Two way wireless system ABAX ACU 100 maximum duration of acoustic signaling ASP 205 wireless indoor siren You can program two types of signaling defining for each of them maximum duration of signaling type of acoustic signaling whether optical signaling is to be enabled 8 ASW 100 230V AC WIRELESS CONTROLLERS IN ABAX SYSTEM The 230 V AC wireless controller takes up 1 position on the list of wireless devices supported by the ACU 100 controller occupies 1 output and 1 zone in the INTEGRA INTEGRA Plus or VERSA alarm system takes up 1 zone and additionally requires 1 ACU 100 cont
67. nd 22 e Specifications have been supplemented p 50 2011 12 4 00 e Section Electronics board has been modified p 4 e Information on ASD 110 wireless smoke and heat detector has been added p 11 2013 04 4 02 e Information on INTEGRA Plus control panels has been added e Information on AMD 103 wireless magnetic contact detector has been added p 11 22 42 and 44 e List of service functions for the controller working in conjunction with INTEGRA INTEGRA Plus control panel has been updated p 35 e Description of the Higher sensitivity for jamming detection option has been added p 42 2014 02 4 03 e Information on ARU 100 radio signal repeater has been added p 13 A note on adding the ARU 100 repeater when the controller is connected to the VERSA control panel has been added p 17 List of service functions for the controller working in conjunction with INTEGRA INTEGRA Plus control panel has been updated p 35 Description of the ARU option has been added p 44 e Section Retransmission has been added p 45 SATEL sp z o o ul Schuberta 79 80 172 Gda sk POLAND tel 48 58 320 94 00 infoQsatel pl www satel eu
68. ntroller name gt NEW DEVICE 2 Enter the 7 digit serial number of the device and press the 4 key The serial number can be found on the electronics board or on the housing Each radio signal level tester has the serial number 0000500 If a device with the entered serial number is already registered in the system the keypad will signal it by 3 long beeps and will fail to proceed to the next step of the procedure 3 After the Open device tamper is displayed turn on power supply of the ACX 200 or ACX 201 expander turn on the ARF 100 tester plug the ASW 100 E ASW 100 F wireless controller into the 230 V socket install the battery in ASD 100 detector violate open the tamper contact in case of the other devices If the serial number of the device to be added is different from the one previously entered a suitable information message will be displayed Press the key and then start the procedure of device addition from the beginning ACU 100 SATEL 19 4 The new device name and serial number will be displayed Press the key 1 to proceed to the next step of the procedure press any other key to terminate the procedure of adding a new device 5 If there is an option to select one or two positions channels for the device in the list of devices a suitable message will be displayed Press the key 1 to select one channel Press the key 2 to select two channels 6 A list of system zones to which the device
69. nutes after itis started through the DLOADX program If the WIRELESS DEVICES window is opened during this time in the DLOADX program the test mode duration will be extended the 30 minute countdown will run from closing the window termination of the service mode in the INTEGRA INTEGRA Plus or VERSA control panel or the keypad connected to the controller closing the DLOAD10 program Notes e According to requirements of the EN50131 standard the level of radio signals sent by wireless devices is reduced during the test mode operation e For the AMD 103 detector entering the test mode remotely is not possible Clear memory this command will erase the memory where information on tampers of wireless devices low battery and jamming is stored Restart communication test the command available in the DLOAD10 and DLOADX programs only which resets the communication test The communication test consists in monitoring the response cycle If during a consecutive poll a device fails to establish communication with the controller the fact is registered and presented as impairment of communication quality The test is carried out in the on line mode and its results are visualized as the Communication quality in percentage form Synchronization the ACU 100 controller checks whether other wireless systems are operating within its range and if so it adjusts the response time accordingly Synchronization is performed a
70. ol panels Information on power supply status and tampers is conveyed by means of the alarm system zones controller outputs The siren allows for independent triggering of optical and acoustic signaling The command to trigger the signaling is transmitted by the controller to the siren immediately Duration of the acoustic signaling cannot exceed the time programmed for the siren Duration of the optical signaling is not limited The siren requires 12 V DC supply A 6 V 1 2 Ah battery can be used as an backup power supply source Note The siren does not test the battery hence the battery status should be periodically checked by the service personnel as part of the maintenance work ACU 100 SATEL 25 Depending on the controller operating configuration the loss of 12 V DC voltage will cause violation of the second zone occupied by the siren in the system communication through the bus with INTEGRA INTEGRA Plus VERSA CA 64 or CA 10 control panels activate the controller LBA output activate the controller output assigned to the optical signaling the second position occupied by the siren on the list of devices Depending on the controller operating configuration the low battery will cause violation of the first zone occupied by the siren in the system communication through the bus with INTEGRA INTEGRA Plus VERSA CA 64 or CA 10 control panels activate the controller LBA output activa
71. ol panels Programming the zones outputs of the expander is possible by using the keypad connected to the controller or by means of the DLOAD10 program It is necessary that operating configuration of the detector connected to the expander be determined and sensitivity defined for each expander zone Additionally the expander zones should be assigned to the selected controller outputs Irrespective of how the expander zones will be programmed the control panel zones to which the ACU 100 controller outputs will be connected are to be configured as NO or NC type see also section INTERACTION WITH ALARM CONTROL PANELS In the LCD keypad any changes of the zone type and sensitivity level are to be done by means of the CONFIGURATION function The A and W keys make it possible to change the parameter values The 4 and gt keys allow you to move between the top and bottom lines of the display i e between the parameters to be programmed In the DLOAD10 program click in the Configuration column on the field referring to the expander zone for which type and sensitivity are to be programmed These parameters are separated by a dash The first position indicates the zone type Using the keypad you can enter here a digit from the 0 to 5 range according to Table 5 Zone type no detector NC NO EOL 2EOL NO 2EOL NC Table 5 The second position indicates the zone sensitivity Using the keypad you can enter a value from the 20ms to
72. on with the control panel is effected by means of the communication bus This way is used for transmission of information on violations of detectors and tampers of wireless devices Control of the detectors changeover to active passive state sirens triggering alarm signal 230V AC controller closing opening the electric circuit etc is performed through the control inputs of the ACU 100 controller Suitably programmed outputs of the alarm control panel should be connected to the control inputs address programming operating mode 25 DLOAD10 CA 64 control panel Fig 9 Example of setting the DIP switches Fig 10 shows a configuration example of the ACU 100 controller working together with the CA 64 control panel The controller communication bus is connected to the second expander bus of the control panel The OUT9 panel low current output has been programmed as type 42 POWER SUPPLY ON ARMED and connected to the AR1 controller control input This input is used to toggle the wireless detectors between their passive and active state The OUT10 panel low current output has been programmed as type 1 BURGLARY ALARM and connected to the AR2 controller control input This input triggers the wireless siren In the presented example the controller information outputs CON JAM LBA remain unconnected They can be connected to the control panel inputs so as to obtain in this way information on troubles related to operation of the wireless devi
73. one out of three types of acoustic signaling selected maximum duration of signaling 1 3 6 or 9 minutes operating mode of optical signaling it can be disabled the symbol displayed or enabled the kd symbol displayed The LCD keypad of INTEGRA INTEGRA Plus system allows you to enable disable the signaling by pressing any numerical key the A and V keys have no effect 13 2 12 ASW 100 E and ASW 100 F controllers Use the A and V keys to select the operating mode of the ASW 100 controller 14 RESTORING CONTROLLER DEFAULT SETTINGS The following parameters are preprogrammed by default e service code 12345 e DLOAD10 identifier 0000000000000000 e response period 24s e problem signaling LED indicator e no registered wireless devices The default factory settings can be restored by means of the SET DEFAULT function in the keypad connected to the controller or by way of hardware restart In order to restore the defaults by means of the hardware restart follow the instructions below 1 Disconnect the controller power supply Disconnect the cables connected to the controller communication bus Short the CLK and DAT terminals Reconnect the power supply A short while after power up the operating mode LED indicator will light in red When default settings are restored the LED color will change to green Open the CLK and DAT terminals 5 6 Disconnect the controller power supply 7 8 AUN
74. only be connected when the controller is configured as a wireless device module interfacing with any alarm control panel The modules should be connected to the controller bus in parallel The connection can be made by means of the unscreened straight through cable using the twisted pair type of cable is not recommended When connecting the modules remember to set the correct number of ACX 100 modules connected to the controller on the controller DIP switches Lack of communication with the module will be signaled on the TPR output as tamper ACU 100 WOO dil dWAWL Act WO RYB CLK DAT COM OLDLDDDDDDDDDDDDDDDO TPR CON JAM LBA OUT1OUT2 OUT3 OUT4 OUTS OUT6 OUT7 OUT8 COM ARI AR2 AR3 ARA UELUT oes Fig 6 Example of connecting two ACX 100 modules addresses 0 and 1 to ACU 100 controller Each module connected to the bus must have a different address set from the range 0 to 4 These addresses must correspond to the number of a next module as shown in Table 4 If one ACX 100 module is connected to the controller it must have address 0 set if two one of them must have address O set and the other address 1 etc The numeration of control inputs and outputs of the expansion module in the system depends on the address set in it See table 4 The module TMP terminals must be connected to the control panel tamper circuit ACU 100 SATEL 17 Consecutive module number Module address Control
75. oth sensors 1 signaling violation after motion is detected by PIR sensor or 2 signaling violation after motion is detected by microwave sensor For example entering the values 4 4 0 means that the PIR sensor sensitivity has been set to 4 the microwave sensor sensitivity also to 4 and in the test mode the detector will signal violation the LED will light up after motion is sensed by both sensors 13 1 3 AMD 100 and AMD 101 detectors Enter the digit O the lower reed switch or 1 the side reed switch to select which of the two reed switches is to be active 13 1 4 AMD 102 detector For the magnetic contact the first position the first zone occupied by the AMD 102 detector enter the digit O the lower reed switch or 1 the side reed switch to select which of the two reed switches is to be active For the roller shutter input the second position the second zone occupied by the AMD 102 detector enter a sequence of two digits 1 digit number of pulses from 1 to 8 2 4 digit pulse validity O 30 s 1 120 s 2 240 s or 3 unlimited duration only switching over the detector from passive into active mode will reset the pulse counter For example entering the values 4 2 means that the zone will be violated after registering 4 pulses and the maximum time that can elapse between the first and the last pulse can be 240 seconds 13 1 5 AGD 100 detector Enter a digit from 1 to 3 which corresponds to the s
76. own in real time with no need for calling any function In the INTEGRA INTEGRA Plus or VERSA system LCD keypad the information on possible lack of communication is given in the user menu TROUBLES submenu and in the DLOADX program in the Troubles window Tamper state this function available in the LCD keypad connected to the controller allows you to check which of the wireless devices are or were tampered with In the DLOAD10 program all the tamper related information is given on line with no need for calling any function In the INTEGRA INTEGRA Plus or VERSA system LCD keypad as well as in the DLOADX program it is possible to check the wireless device controller for presence of tamper by using the EveNTS function Additionally the information on possible tampers of wireless devices can be found in the DLOADX program in the Zones state Battery status function is available in the LCD keypad connected to the controller Depending on the type of device the low battery message may indicate low battery detectors loss of 12 V DC supply ASP 105 siren loss of 18 V AC supply ACX 201 expander discharged battery ASP 105 siren ACX 201 expander overload of AUX1 or AUX2 supply output ACX 201 expander In the DLOAD10 program information on the status of battery power supply storage battery supply outputs is given in on line mode in the Battery column In the INTEGRA INTEGRA Plus or VERSA
77. puter the computer must be connected to the RS 232 port Connection between the controller RS 232 port and the computer port should be made as shown in the picture below you can buy a ready made cable manufactured by SATEL RTS cts DTR 4C_5 TXD 3 C2 eases Fig 5 Connection of computer to the controller serial port PIN5 plug is shown on the left DB 9 female plug is shown on the right as seen from solder side Notes e Do not short or touch the RS 232 port with your fingers e Prior to connecting the cable remove preliminarily the electrostatic charge e g by touching a grounded piece of equipment faucet heater etc with top of your palm 16 Two way wireless system ABAX ACU 100 e It is recommended that the cable be first connected to the controller port If the DLOAD10 program fails to communicate with the computer after connection of the RS 232 port you should check that the option of programming by means of RS 232 port has been selected on the controller DIP switches check that the port through which the computer communicates with the controller has been properly selected in the DLOAD10 program check that the cables connecting the computer with controller have been properly connected 4 4 CONNECTING THE ACX 100 INPUT amp OUTPUT EXPANSION MODULES The ACU 100 controller communication bus can accept up to five ACX 100 input amp output expansion modules The modules can
78. r to the CA 10 control panel 10 4 MODULE OF WIRELESS DEVICES ANY ALARM CONTROL PANEL Using the DIP switches set the suitable operating mode of the ACU 100 controller number of ACX 100 modules which are connected to it as well as the programming mode number of ACX 100 modules programming operating mode 3 keypad any control panel Fig 13 Example of setting the DIP switches 34 Two way wireless system ABAX ACU 100 pe Z AE QOD bw ouT2 com ode KPD DTA Z 74 Z DODO T LET ACU 100 A RS485 B _CLK_ DAT COM WOO dWLI dNL dil Ack WOD Fig 14 Example of connecting the ACU 100 controller to the CA 6 control panel Communication with the control panel in this configuration is effected by means of controller outputs and inputs The controller outputs to which the wireless devices are assigned should be connected to the control panel zones Control of the detectors changeover to active passive state sirens triggering alarm signal 230 V AC controller closing opening the electric circuit etc is performed through the control inputs of the ACU 100 controller Suitably programmed outputs of the alarm control panel should be connected to the control inputs Shown in the example Fig 14 is the CA 6 alarm control panel of SATEL make however it can be any other panel as well Th
79. re proceeding to the system installation you should plan the arrangement of all the devices The installation place for the controller should be chosen so that all devices to be supervised by it are within its range It is recommended that the controller and the wireless 14 Two way wireless system ABAX ACU 100 devices be mounted at a high position which will enable a better range of radio communication to be reached while avoiding a risk of incidental masking of the controller and devices by people moving around the facility Before permanently mounting the system components you should check the level of signal received by the controller from individual devices A helpful instrument for checking the signal level is the SATEL made ARF 100 tester If the signal level from a particular unit is too low less than 40 a change of the device position will be necessary At times it is sufficient to move the device some ten to twenty centimeters to get a significant improvement of the signal quality Having reached the optimal level of radio signal from all devices you can proceed to permanently mounting them in position Several ACU 100 controllers can work within each other s range Automatic synchronization with the wireless systems already in use is always performed when the controller is switched on and after each operation of addition removal of supported devices The number of wireless devices already working within the range of each other dep
80. roller input to control operation in the CA 64 or CA 10 alarm system requires 1 zone and 1 ACU 100 controller output when working with other control panels Depending on the ASW 100 controller operating configuration the electric circuit is closed on activating the INTEGRA INTEGRA Plus or VERSA system output to which the ASW 100 controller is assigned The output must be programmed accordingly on activating the ACU 100 controller input which has been selected as the control one The command to close open the 230 V electric circuit is transmitted by the ACU 100 controller to the ASW 100 controller at once The ASW 100 E and ASW 100 F controllers can work in three modes given in square brackets is description from the LCD keypad of INTEGRA INTEGRA Plus or VERSA system mode 0 button inactive the electric circuit is only remotely controlled mode 1 button interim control the electric circuit can be controlled remotely or manually mode 2 button combined control the electric circuit can be controlled remotely or manually but remote control can be manually overridden Information transmitted through the alarm system zone ACU 100 controller output depends on the ASW controller operating mode mode 0 button status It is sent immediately mode 1 or 2 electric circuit status It is only sent during polling time see RESPONSE PERIOD Pressing the button closing the electr
81. t it has not yet come The manner of permanently switching the detector to its active state depends on the controller working configuration If the controller operates together with the INTEGRA INTEGRA Plus or VERSA series control panels select the corresponding option for wireless detector Otherwise the controller input for detector control should be programmed as always active A According to the EN50131 3 standard all Hold Up devices used with ACU 100 controller must be always in active mode The batteries ensure operation of the detectors for a period of about 3 years provided that they remain in the passive state for some portion of that period and the RESPONSE PERIOD is 12 seconds A longer polling period 24 or 36 seconds means extension of the battery life time The battery life time in the detectors switched permanently into the active mode is shorter than in those ACU 100 SATEL 23 which are periodically switched to the passive mode However if the specific character of a detector or its installation place is such that the number of violations is low switching the detector permanently into the active mode will not adversely affect the battery life time 6 1 ADDITIONAL DETECTOR PARAMETERS TO BE CONFIGURED APD 100 wireless passive infrared detector Sensitivity is to be programmed In case of detectors with firmware version 2 01 determine additionally whether the option of immunity to pets up to 15 kg in weight shoul
82. te the controller output assigned to the acoustic signaling the first position occupied by the siren on the list of devices 7 2 DESCRIPTION OF ASP 205 SIREN FUNCTIONING A Do not leave the ASP 205 siren with its battery inside if the siren is not installed in the system The wireless device which has no communication with the control panel for more than 10 minutes will consume more energy thus reducing the battery life The ASP 205 wireless indoor siren occupies 2 positions on the list of devices supported by the controller takes up 2 outputs and 2 zones in the INTEGRA INTEGRA Plus or VERSA alarm system takes up 2 zones and also requires 2 controller inputs to control signaling in the CA 64 or CA 10 alarm system requires 2 inputs and at least 1 controller output when used in conjunction with other control panels the output is assigned to each of the two positions occupied by the siren on the list of devices hence it is possible to assign two outputs but the same information will be supplied to both of them Information on power supply status and tampers is conveyed by means of the alarm system zones controller outputs The siren allows for independent triggering of two different types of signaling with programmable parameters A command to trigger the signaling is only send to the siren during the response time Hence the cutoff time of the control panel outputs which control the ASP 205 wireless indoor sire
83. ted description of LBA function output p 5 9 e Added information on new wireless devices of ABAX system hard wired zones and outputs expander with power supply ACX 201 p 9 20 wireless dual motion detector p 10 wireless glass break detector p 11 wireless water flood detector p 11 wireless vibration and magnetic detector p 11 and wireless smoke and heat detector p 11 e Modified section on adding new devices to ABAX system p 17 19 e Added information on lowering the radio signal level during test mode operation p 27 44 e Modified and supplemented description of Battery status function p 43 2008 07 2 00 e Information on pet immunity has been added to description of APD 100 detector p 10 e Information on APD 100 detector configuration has been modified and supplemented p 23 45 and 48 e Information on AMD 100 and AMD 101 detector configuration has been modified and supplemented p 23 46 and 48 e Section Zone expander for CA 10 control panel has been modified p 31 52 Two way wireless system ABAX ACU 100 2009 07 2 01 e Added information on interaction with VERSA control panel e Modified section on controller control inputs p 7 e Modified section on controller control outputs p 8 e Added information about AMD 102 wireless magnetic contact with roller shutter input p 10 23 46 and 49 e Added information about ARD 100 wireless reorienta
84. tion detector p 12 23 47 and 49 e Added information about APT 100 bidirectional keyfob p 12 e Revised section Installation subsections on detectors p 22 sirens p 24 wireless controllers p 26 and radio signal level tester p 26 have become separate subsections and all of them have been modified information on installation of particular wireless devices has been deleted it can be found in manuals of respective devices description of configuration of particular devices has been moved to section Configuration of additional parameters and options in wireless devices p 45 e Added information about the method of configuration of INTEGRA system zones to which wireless devices are assigned p 30 e Added information about the method of configuration of CA 64 system zones to which wireless devices are assigned p 31 e Added subsection about programming ABAX wireless system by means of VERSA alarm system keypad p 35 e Added subsection about configuration of additional parameters and options of wireless devices p 45 2011 05 3 00 e Information on ATD 100 wireless temperature detector has been added p 12 24 47 and 49 e Information on AMD 102 ATD 100 and AVD 100 detectors which can take one or two positions in the list of wireless devices has been added to section Adding new wireless devices p 17 19 e Information on requirements of standard EN50131 3 has been added p 20 a
85. ts A RS485 B RS 485 port terminals not used 6 Two way wireless system ABAX ACU 100 CLK DAT communication bus It enables direct connection to the control panel communication bus INTEGRA INTEGRA Plus VERSA CA 64 CA 10 or expansion of the system by adding the ACX 100 input output expansion modules 2 2 FUNCTIONS OF DIP SWITCHES DIP switch number Controller function Wireless device module for all control panels Expander for CA 10 with 1 keypad 6 zones Expander for CA 10 with 2 keypads 4 zones Expander for CA 10 with 3 keypads 2 zones Addressable zone expander for CA 64 Wireless device expander for INTEGRA INTEGRA Plus or VERSA control panels Table 1 The way of using DIP switches for controller configuration 0 DIP switch in OFF position 1 DIP switch in ON position P selection of controller programming mode DIP switch in OFF position through RS 232 port DLOAD10 program DIP switch in ON position by means of LCD keypad h le 13 DIP switches for setting the number of ACX 100 modules connected to the computer To determine this number tot up the values set on individual DIP switches as per Table 2 DIP switch number Numerical value for switch in ON position Table 2 The controller accepts up to 5 input output expansion modules hence if a higher value is set on the DIP switches it will be also recognized as 5
86. tted through the communication bus 3 WIRELESS DEVICES INTERFACING WITH THE CONTROLLER 3 1 ACX 100 INPUT amp OUTPUT EXPANSION MODULE e 4 control inputs e 8 outputs OC type e communication bus e tamper contact e power supply direct voltage 12 V 15 3 2 ACX 200 HARDWIRED ZONE OUTPUT EXPANDER e 4zones e 4relay outputs e tamper contact e power supply direct voltage 12 V 15 3 3 ACX 201 HARDWIRED ZONE OUTPUT EXPANDER WITH POWER SUPPLY e 4zones e 4relay outputs e switching mode power supply 1 2 A capacity e battery charging and control system e power supply 18 V AC 10 Two way wireless system ABAX ACU 100 3 4 APD 100 WIRELESS PASSIVE INFRARED DETECTOR e digitally processed signal from pyroelectric sensor e high resistance to interference e adjustable detection sensitivity e option of immunity to pets up to 15 kg in weight detectors with firmware version 2 01 or newer e remote configuration of parameters e changeable Fresnel lenses e tamper contacts e power supply lithium battery CR123A 3V 3 5 APMD 150 WIRELESS DUAL MOTION DETECTOR e microwave MW sensor and double pyroelectric PIR element e advanced power management e high immunity to interference and false alarms e independent sensitivity adjustment for PIR and MW e remote configuration e tamper contacts e power supply lithium battery CR123A 3V 3 6 AMD 100 WIRELESS MAGNETIC DETECTOR e two reed switches e input
87. two way wireless X system WIRELESS SYSTEM CONTROLLER ACU 100 Program version 4 03 User Manual Senes C 14710 acu100 en 02 14 N IMPORTANT The controller incorporates electronic components sensitive to electrostatic discharges Prior to installation remove the electrostatic discharges and avoid touching the controller board components in the process of installation Do not deform the controller antenna as this may adversely affect the quality of radio communication Hereby SATEL sp z 0 0 declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at www satel eu ce The SATEL Company sets itself an objective to continually enhance quality of its products which can entail changes to their technical specifications and software Information on the introduced modifications can be found on our web site Please visit us at http www satel eu New features of the ACU 100 controller with firmware version 4 03 e Support for new wireless device ARU 100 radio signal repeater 2 Two way wireless system ABAX ACU 100 CONTENTS 1 Generala mule ide cado a TER Arial GA A o Un oa mes 4 2 Description of ACU 100 wireless system controller ccccccceceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeenes 4 2 4 Electronics boarda nter erbe rer En A deen fer edi died Eee to Ee Le E EO 4 2 2 Functions of DI
88. utomatically on starting the controller and after each operation of addition removal of devices supported by it Additionally it can be started manually with this command Supply voltage function if the LCD keypad which allows the controller supply voltage level to be checked In the DLOAD10 DLOADX programs the information on supply voltage is provided in on line mode with no need for starting any function whatever In Out module tampers information on communication of the controller with the ACX 100 input output expansion modules available in the DLOAD10 program only Lack of communication is recognized as the module tamper ARU Use ARU 100 parameter available for a wireless device if the ARU 100 repeater is registered in the controller It allows you to define whether the device is to communicate to the controller directly or via the selected ARU 100 repeater several ARU 100 repeaters can be registered in the controller The programming procedure is described in section RETRANSMISSION Tamper alarm in partition Expander tamper this option available when the controller is connected to the INTEGRA INTEGRA Plus or VERSA control panel makes it possible to indicate the partition where alarm will be triggered in the event of controller tamper No blocking after 3 tampers option available when interacting with the INTEGRA INTEGRA Plus series control panel The controller generates alarm on opening the tamper contact
89. ved Note If the ACU 100 controller is connected as an expansion module to the CA 64 INTEGRA or INTEGRA Plus control panel a new identification of expanders must be carried out after completion of the procedure of removal of a new wireless device from the system 4 6 2 LCD keypad In order to remove a wireless device from the system you should 1 Start the REMOVE DEVICE function 2 Select from the list the device to be removed from the system and press 3 Following the displayed instruction press the key with digit 1 to remove the device Removal of the device will be acknowledged by the keypad with four short and one long beeps Note Pressing any key instead of the key 1 will take you back to the selection list of wireless devices 20 Two way wireless system ABAX ACU 100 5 HARDWIRED ZONE OUTPUT EXPANDERS IN ABAX SYSTEM The hardwired zone output expander ACX 200 or ACX 201 takes up 4 positions on the list of devices supported by the controller Up to 12 hardwired zone output expanders can work together with the ACU 100 controller The expander provides real time information on the zone status The controller sends to the expander commands to change the status of outputs in real time and to modify the settings of zones during polling Data related to configuration of one zone are sent during one response period hence 4 response periods are needed to send information on the settings of 4 zones more than 2 minutes
90. wireless zones in the system will amount to 8 The control panel zones to which the controller outputs have been connected should be configured as NO type Still available are the control panel zones from Z3 to Z8 You can connect to them wire operated devices or consecutive controller outputs as well as wireless devices assigned to them The OUTS control panel low current output has been programmed as type 35 POWER SUPPLY ON ARMED MODE and connected to the AR1 controller control input This input switches the wireless detectors from passive to active state and vice versa The OUT6 control panel low current output has been programmed as type 01 BURGLARY ALARM and connected to the AR2 controller control input This input triggers the wireless siren In the presented example the controller information outputs TPR CON JAM LBA have remained unconnected These ACU 100 SATEL 33 outputs can be connected to the control panel zones so as to obtain in this way information on problems connected with operation of wireless devices SYNT iS M OUT6 OUTS fav D SQQ Jj ZA PO OOO O Ee op OO 0005000090000 O 4 COM KPD DATA CLK1 CLK2 f UN Z1 COM Z2 COM Z4 Z5 COM Z6 77 COM Z8 NN OUT2 OUT1 CLK DAT ACU 100 200 DOWGOOSOP DOG Lp 2 O62 000P OO NISZA NL Z WOO dIALI dNL diNL AZl WOD Fig 12 Example of connecting the ACU 100 controlle
91. ypad to be connected to the ACU 100 controller must be set as 0 If properly connected the keypad will display a message the upper line of which will include the device name and program version info If the rA TROUBLE LED goes on in the ACU 100 SATEL 15 keypad one of the functional outputs is active In order to start the service mode the service code must be entered The service mode is indicated by lighting of the 39 SERVICE LED If the a m message fails to appear on the display after connection you should check that the option of programming by means of LCD keypad has been selected on the controller DIP switches check that the cables connecting the keypad with controller have been properly connected check that address 0 has been set in the LCD keypad In order to check the keypad address and if necessary to change it 1 Disconnect the KPD keypad power supply and the data bus cables CKM DTM 2 Short the CKM DTM keypad terminals 3 Connect the keypad power supply 4 The keypad address will be displayed n 0 7 current address of the keypad Fig 4 Programming the keypad address 5 Change the address to O if necessary The keypad will acknowledge performance of the function with four short and one long beeps 6 Connect the keypad to the ACU 100 controller as required CKM DTM 4 3 CONNECTING COMPUTER TO THE CONTROLLER If the ACU 100 controller is to be programmed by means of a com

ACU-100

Contents

Download Pdf Manuals

Related Search

Related Contents