Home
Dotz Brick 3.3
Contents
1. ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX d and PIN 3 DMX of the last fixture Figure 4 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for DATA transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion Conductor 3 Pin XLR Female Out 5 Pin XLR Male In Ground Shield Pin 1 Pin 1 Data Compliment signal Pin 2 Pin 2 Data True signal Pin 3 Pin 3 Not Used Do Not Use Not Used Do Not Use ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 6 Dotz Brick 3 3 System Menu Built In Programs Blackout STATIC COLOR Red Green Blue Yellow Cyan Purple White CL RGB Flash00 99 Flash speed adjustable DREAM Seven color dreaming Speed00 99 Flash00 99 Speed amp Flash adjustable METEOR Seven color flow Speed00 99 Flash00 99 Speed amp Flash adjustable FADE Seven color fade Speed00 99 Flash00 99 Speed amp Flash adjustable C
2. is displayed 4 The slave units will now follow the Master unit ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 11 Dotz Brick 3 3 Pixel Flip Settings Dotz Brick 3 3 Photometrics Follow this chart to figure out your desired Pixel setup Your de desired setting only works in 27 Channel mode and 32 Channel mode Intensity LUX j Red LEDs 974 270 114 6 45 STANDARD Green LEDs 1444 405 185 109 71 Blue LEDs 2010 574 270 154 10 1 2 3 Full LEDs 3370 1014 475 265 171 6 5 4 7 8 3 Flip 1 3 2 1 2 4 5 6 gt E 1 9 8 7 E o Flip 2 a 0 9 8 7 E ZO A 5 6 Q1 3 2 1 2 Flip 3 7 8 9 3 6 5 4 0 1 2 3 4 5 1 2 3 25 Diameter m 0 65 1 08 153 197 2 41 30 Diameter m 0 75 1 27 1 80 233 2 87 Flip4 1 2 3 4 5 6 7 8 9 ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 12 ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 13 Dotz Brick 3 3 3 Channel Mode Dotz Brick 3 3 8 Channel Mode Channel Value 1 Function _ ______ k Function _ _ ___ k 0 255 0 100 0 100 0 255 0 100 0 100 3 BLUE BLUE 0 100 0 100 COLOR MACROS amp PROGRAMS Dotz Brick 3 3 NO FUNCTION RED RED GREEN 0 100 BLUE GREEN RED amp GREEN 0 100 GREEN amp BLUE BLUE RED amp BLUE 0 100 RED GREEN amp BLUE MASTER DIMMER COLOR
3. www adj com Dotz Brick 3 3 User Manual Page 19 Dotz Brick 3 3 32 Channel Mode Channel Value TST PROGRASPEEDISOURD SENSE PROGRAM SPEED SOUND SENSE 0 255 PROGRAM SPEED SLOW FAST MASTER DIMMER 0 100 BORT 0 255 SLOW FAST DIMMER CURVES 0 41 STANDARD 42 84 STAGE 85 127 TV 128 170 ARCHITECTURAL 171 213 THEATER 214 255 DEFAULT TO UNIT CURVE SETTING When Channel 28 is being used between the values of 136 239 Channel 29 will control the speed of the programs When Channel 28 is being used between the values of 240 255 Channel 29 will control sound sensitivity ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 20 Dotz Brick 3 3 Installation When installing the unit the trussing or area of installation must be able to hold 10 times the weight without any deformation When installing the unit must be secured with a secondary safety attach ment e g and appropriate safety cable Never stand directly below the unit when mounting removing or servicing the unit Overhead mounting requires extensive experience including calculat ing working load limits installation material being used and perodic safety inspection of all installation material and unit If you lack these qualifications do not attempt the installation yourself These installaiton should be checked by a skilled person once a year The Dotz Brick 3 3 is fully operational in two different mounting posi tions
4. 2 Press ENTER to move through the various adjustments of each program and use the UP and DOWN button to make adjust ments Dim Curve This setting will let you select your desired dimming curve 1 Press the MENU button until Dim Curve is displayed press ENTER 2 1 of 5 dimming curve settings will be displayed Standard Stage TV Architectural or Theatre Use the UP and DOWM but tons to select your desired dimming curve and press ENTER to confirm Pixel Flip In this mode you adjust the unit so that the LEDs in DMX mode will illuminate at your desired starting point See the diagram on page 12 to selet your Pixel setting 1 Press the MENU button until Pixel Flip is displayed press ENTER ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 9 Dotz Brick 3 3 System Menu 2 Either Standard or 1 of 4 modes will be displayed Use the UP and DOWN buttons to find your desired mode and press ENTER NO DMX This mode can be used as a precaution mode that in case the DMX signal is lost the operating mode chosen in the setup is the running mode the fixture will go into when the DMX signal is lost You can also set this as the operating mode you would like the unit to return to when power is applied 1 Press the MENU button until NO DMX is displayed and either Sound Auto Black or Hold will be displayed beneath 2 Press ENTER and the bottom choice will b
5. B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the pro duct only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instru ment is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at
6. hanging upside down from a ceiling or set on a flat level sur face To avoid internal damage to the unit never mount the unit on its side as illustrated above Be sure this fixture is kept at least 0 5m away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent acci dental damage and or injury in the event the clamp fails Never use the carrying handles for secondary attachment Dotz Brick 3 3 Power Cord Daisy Chaining With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 7 fixtures maximum for 120V and 14 fixtures maxi mum for 230V After the maximum fixtures has been reached you will need to use a new power outlet They must be the same fix tures DO NOT mix fixtures ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 21 Dotz Brick 3 3 Locate and remove the unit s power cord Once the cord has been removed located the fuse holder located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder has a built in socket for a spare fuse be sure not to confuse the spare fuse with active fuse Dotz Brick 3 3 Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses must be carried out periodically to optimize lig
7. in a master slave configuration 1 Press the MENU button until Slave Mode is displayed Your unit will now follow the Master Sound Mode tn this mode the unit will run in sound active mode 1 Press the MENU button until Sound Mode is displayed 2 Press ENTER to adjust your sound sensitivity When you press ENTER the number next to Sens will begin to flash use the UP and DOWN buttons to adjust the sound sensitivity Once you found your desired sensitivity press ENTER to confirm 3 When you press ENTER the number next to FQN will not begin to flash use the UP and DOWN buttons to adjust the fre quency rate Press ENTER to confirm your setting Auto Run 1 Press the MENU button until Auto Run is displayed press ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 8 Dotz Brick 3 3 System Menu ENTER 2 FQN XX will now be displayed XX representing the Fre quency Rate Auto Run speed 3 Press ENTER and the number will begin to flash use the UP and DOWN buttons to adjust the speed 01 being the slowest and 99 being the fastest Press ENTER to confirm Built In Programs See the chart on page 7 to find your desired program Built In Programs will not be dis played one of the programs listed on page 7 will 1 Press the MENU button until one of the Programs on page 7 is displayed The displayed program depends on the last pro gram you had set the unit to
8. its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC AI products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to
9. 1 0 100 COLOR 2 COLOR 3 COLOR 4 DIMMER CURVES COLOR 5 STANDARD COLOR 6 STAGE COLOR 7 TV COLOR 8 ARCHITECTURAL COLOR FADE 1 THEATER COLOR SNAKE 214 255 DEFAULT TO UNIT CURVE SETTING COLOR FADE 2 COLOR CHANGE COLOR FLOW 1 COLOR FLOW 2 COLOR FLOW 3 COLOR FLOW 4 COLOR FLOW 5 COLOR FLOW 6 216 223 COLOR FLOW 7 ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 14 ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 15 Dotz Brick 3 3 8 Channel Mode Dotz Brick 3 3 27 Channel Mode Channel Value Function COLOR MACROS amp PROGRAMS RED 1 216 223 COLOR FLOW 7 0 100 224 231 COLOR FLOW 8 GREEN 1 232 239 COLOR FLOW 9 0 100 240 247 COLOR FLOW 10 BLUE 1 248 255 N G 0 100 0 255 PROGRAM SPEED SLOW FAST 0 100 6 0 255 MASTER DIMMER 0 100 GREEN 2 0 255 SLOW FAST BLUE 2 DIMMER CURVES 0 100 0 41 STANDARD REDS 42 84 STAGE 0 100 85 127 TV GREEN 3 128 170 ARCHITECTURAL 0 100 171 213 THEATER BLUES 214 255 DEFAULT TO UNIT CURVE SETTING 100 When Channel 4 is being used between the values of 136 239 Channels 10 21 continue the same RGB LED Pattern Channel 5 will control the speed of the programs When Channel 4 is being used between the values of 240 255 RED 8 Channel 5 will control sound sensitivity 0 255 0 100 GREEN 8 0 100 BLUE 8 0 100 RED 9 0 100 GREEN 9 0 100 BLUE 9 0 100 ADJ Prod
10. 10 13 User Instructions 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indi rect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent assembly installation rigging and operation of this product Dotz Brick 3 3 Introduction Unpacking Thank you for purchasing the Dotz Brick 3 3 by ADJ Products LLC Every Dotz Brick 3 3 has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appe
11. 3 Channel Mode 6 Channel Mode 8 Channel Mode 27 Channel Mode amp 32 Channel Mode Any safe working position 3 Year 1095 days Working Position Warranty Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 26 ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com ADL Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands service adjgroup eu www adj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On HOM facebook com americandj twitter com americandj youtube com adjlighting
12. HANGE Seven color change Speed00 99 Flash00 99 Speed amp Flash adjustable FLOW 1 Seven color chase Speed00 99 Flash00 99 Speed amp Flash adjustable FLOW 2 Seven color chase Speed00 99 Flash00 99 Speed amp Flash adjustable FLOW 3 Seven color chase Speed00 99 Flash00 99 Speed amp Flash adjustable FLOW 4 Seven color chase Speed00 99 Flash00 99 Speed amp Flash adjustable FLOW 5 Seven color chase Speed00 99 Flash00 99 Speed amp Flash adjustable FLOW 6 Seven color chase Speed00 99 Flash00 99 Speed amp Flash adjustable FLOW 7 Seven color chase Speed00 99 Flash00 99 Speed amp Flash adjustable FLOW 8 Seven color chase Speed00 99 Flash00 99 Speed amp Flash adjustable FLOW 9 Seven color chase Speed00 99 Flash00 99 Speed amp Flash adjustable ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 7 Dotz Brick 3 3 System Menu The LCD backlight will shut off after 30 seconds to relight the background press the MODE button for 5 seconds DMX Mode Set the DMX Address and DMX Channel Mode 1 Press the MENU button until DMX Mode and underneath ADDR XXX and CH XX is displayed press ENTER 2 XXX will now begin to flash use the UP and DOWN buttons to find your desired DMX address then press ENTER 3 XX will now begin to flash use the UP and DOWN buttons to find your desired DMX Channel mode then press ENTER Slave Mode This will let you set your unit as a slave
13. ars to be damaged carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact In the case damage has been found or parts are missing please contact our toll free customer support number for fur ther instructions Do not return this unit to your dealer without first con tacting customer support Introduction The Dotz Brick 3 3 is part of ADJ s continuing pursuit for creating high quality affordable intelligent fixtures The Dotz Brick 3 3 is a high performance DMX intelligent moving head LED fixture This fixture is a great piece for retail stores displays mood architec tural interior and exterior decoration and clubs This unit can be used as a stand alone or in a Master Slave configuration The unit can also be controlled via DMX controller This fixture is suitable for theaters studios retail stores and other similar locations Customer Support ADJ Products LLC provides a toll free cus tomer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail support americandj com To purchase parts online visit http parts americandj com Warning To prevent or reduce the risk
14. de see page 8 1 This function will allow you to control each individual fixture s traits with a standard DMX 512 controller such as the Elation Show Designer or the Elation DMX Operator 2 Torun your fixture in DMX mode follow directions on page 8 to set your DMX address and DMX Channel mode 3 Plug in the fixture via the XLR connections to any standard DMX controller 4 For longer cable runs more than a 100 feet use a terminator on the last fixture Dotz Brick 3 3 Master Slave Configuration Master Slave Operation This function will allow you to link up to 16 units together and operate without a controller The units will be sound activated In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 Using approved DMX data cables daisy chain your units together via the XLR connector on the rear of the units Remember the Male XLR connector is the input and the Female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only For longer cable runs we suggest a termina tor at the last fixture 2 On the Master unit designate the unit as a Master unit following the instructions on page 10 Then set your desired operating mode 3 On the slave units press the MODE button until Slave Mode
15. e unit s main power e Always mount this unit in safe and stable matter e Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit e Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 22 for cleaning details e Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances inclu ding amplifiers that produce heat The fixture should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 4 Dotz Brick 3 3 Set Up Power Supply The ADJ Dotz Brick 3 3 contains a automatic volt age switch which will auto sense the voltage when it is plugged into a power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere Always use the PowerCon cord that came with the unit DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and contr
16. egin to flash Use the UP or DOWN buttons to choose an operating mode you would like the unit to start up in when power is applied or the DMX signal is lost e Sound If the DMX signal is lost or power is applied the unit will automatically go into sound active mode e Auto If the DMX signal is lost or power is applied the unit will automatically go into Auto Run mode e Black Blackout If the DMX signal is lost or power is applied the unit will automatically go into stand by mode e Hold If the DMX signal is lost the fixture will stay in the last DMX setting If power is applied and this mode is set the unit will automatically go into the last DMX set up 3 Press ENTER to confirm your desired set up Personality This will let you set your unit as a Master in a master slave configuration 1 Press the MENU button until Personality is displayed Your unit will now be the Master unit in a Master Slave configuration ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 10 Dotz Brick 3 3 Universal DMX Control Universal DMX Control This function allows you to use a Elation universal DMX 512 controller to control the chases and patterns dimmer and strobe A DMX controller allows you to create unique programs tailored to your individual needs The Dotz Brick 3 3 has 5 DMX channel modes a 3 Channel Mode 6 Channel Mode 8 Channel Mode 27 Channel Mode amp 32 Channel Mode To select your channel mo
17. ght pre paid and accompany a return authorization R A number If the unit is under warranty you must provide a copy of your proof of purchase invoice Please contact ADJ Products LLC customer support for a R A number Warranty Registration ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 3 Dotz Brick 3 3 Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside e Never operate this unit when it s cover is removed e Never plug this unit in to a dimmer pack e Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged e This unit is intended for indoor use only use of this product out doors voids all warranties e During long periods of non use disconnect th
18. ht output Fuse Replacement Cleaning 1 Use a soft cloth to wipe down the outside casing Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew Dotz Brick 3 3 Troubleshooting Listed below are a few common problems the user may encounter with solutions Unit not responding to DMX 1 Check that the DMX cables are connected properly and are wired correctly pin 3 is hot on some other DMX devices pin 2 may be hot Also check that all cables are connected to the right connectors it does matter which way the inputs and outputs are connected Unit does not respond to sound 1 Quiet or high pitched sounds will not activate the unit If problems are not resolved Contact ADJ Products LLC for service 1 800 322 6337 ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 22 Dotz Brick 3 3 Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought
19. of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact ADJ Products LLC PLEASE recycle the shipping carton when ever possible ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 2 Dotz Brick 3 3 General Instructions To optimize the performance of this product please read these operat ing instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Dotz Brick 3 3 Features RGB Color Mixing Strobing e Electronic Dimming 0 100 e Built in Microphone e DMX 512 protocol e Five DMX Modes 3 Channel Mode 6 Channel Mode 8 Channel Mode 27 Channel Mode amp 32 Channel Mode 4 Operating Modes Sound Active Auto Run Built In Programs or DMX Control e Power Cord Daisy Chaining See Page 21 Dotz Brick 3 3 The Dotz Brick 3 3 carries a 3 year 1095 days limited warranty Please fill out the enclosed warranty card to validate your purchase and warranty You may also register your product online at www americandj com All returned service items whether under warranty or not must be frei
20. ollers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATA IN and DATA OUT XLR ter minals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compli ant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX Operation The Dotz Brick 3 3 can be controlled via DMX 512 protocol The Dotz Brick 3 3 has 5 DMX Channel Modes The DMX address is set on the rear panel of the Dotz Brick 3 3 Your unit and your DMX controller require a approved DMX 512 110 Ohm Data cable for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use s
21. tandard 110 120 Ohm shielded cable This cable may be purchased at almost all professional sound and lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split Figure 1 ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 5 Dotz Brick 3 3 Set Up Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR XLR Male Socket XLR Female Socket 1 Ground 7 2 Cold Figure 3 Figure 2 XLR Pin Configuration 1 2 Cold I d 1 Ground i Pin 1 Ground 1 S s n l Pin 2 Data Compliment negative 1 1 Pin 3 Data True positive EE EEE E EEE EEE EE EEE Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 90 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator
22. ucts LLC www adj com Dotz Brick 3 3 User Manual Page 16 ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 17 Dotz Brick 3 3 32 Channel Mode Dotz Brick 3 3 32 Channel Mode Function _ _____ Function __ _ _ k RED 1 COLOR MACROS amp PROGRAMS 0 255 Channels 10 21 continue the same RGB LED Pattern 0 255 0 255 0 255 0 255 0 255 0 255 ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 18 0 100 GREEN 1 0 100 BLUE 1 0 100 RED 2 0 100 GREEN 2 0 100 BLUE 2 0 100 RED 3 0 100 GREEN 3 0 100 BLUE 3 0 100 RED 8 0 100 GREEN 8 0 100 BLUE 8 0 100 RED 9 0 100 GREEN 9 0 100 BLUE 9 0 100 0 15 16 23 24 31 32 39 40 47 48 55 56 63 64 71 72 79 80 87 88 95 96 103 104 111 112 119 120 127 128 135 136 143 144 151 152 159 160 167 168 175 176 183 184 191 192 199 200 207 208 215 216 223 216 223 224 231 232 239 240 255 NO FUNCTION RED GREEN BLUE RED amp GREEN GREEN amp BLUE RED amp BLUE RED GREEN amp BLUE COLOR 1 COLOR 2 COLOR 3 COLOR 4 COLOR 5 COLOR 6 COLOR 7 COLOR 8 COLOR FADE 1 COLOR SNAKE COLOR FADE 2 COLOR CHANGE COLOR FLOW 1 COLOR FLOW 2 COLOR FLOW 3 COLOR FLOW 4 COLOR FLOW 5 COLOR FLOW 6 COLOR FLOW 7 COLOR FLOW 7 COLOR FLOW 8 COLOR FLOW 9 SOUND ACTIVE ADJ Products LLC
23. use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 90 Day Limited Warranty e L E D Products 3 year 1095 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty Only the L E D s carry a 3 year warranty ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 23 Dotz Brick 3 3 Notes Dotz Brick 3 3 Notes ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 24 ADJ Products LLC www adj com Dotz Brick 3 3 User Manual Page 25 Dotz Brick 3 3 Specifications SPECIFICATIONS Voltage 100V 240V 50HzZ 60Hz LEDs 9 x 9W COB TRI LEDs Power Consumption 116W Total All LED s Full Beam Angle 25 Degrees Fuse 2Amp Power Cord Daisy Chain 7 Fixtures Max 120V 14 Fixtures Max 230V Weight 11lbs 4 8Kgs Dimensions 10 25 L x 6 75 W x 12 H 259 x 169 x 300mm Colors RGB Color Mixing DMX Channels
Download Pdf Manuals
Related Search
Related Contents
lire l`article de Norbert Czarny PBworks User Manual: Plugins Oracle Enterprise Manager 1.0.4.0.0 User's Manual Kicker CompVR-CVR15/CVR12/CVR10/CVR8 Owner's Manual Efficient Semiconductor Solutions for Motor Control and Drives Guía del Usuario MLEK-A800W2LRD 取扱説明書 Light Level Sensor – Ceiling Mounted Copyright © All rights reserved.
Failed to retrieve file